Manuel d'utilisation / d'entretien du produit MA4100 du fabricant TUBE DRIVER
Aller à la page of 19
OWNERS MANUAL MA4100 Congratulations Endpanel Layout Features & Specifications Endpanel Layout Installation Troubleshooting Wiring Troubleshooting Power / Ground Troubleshooting Connections Troubl.
The extended use of a high powered audio system may result in hearing loss or damage. While TUBE DRIVER systems are capable of "Concer t Le v el" volumes with incredible accuracy , they are also designed for you to enjoy at more reasonable levels all of the sonic subtleties created by musicians.
1 Power Bandwidth: 5 Hz -50 KHz T otal Harmonic Distortion: 0.2% or less (A-weighted) Input T opology: Balanced Differential Input Sensitivity: 500mV - 12 volts RMS Input Impedance: 10K Ohms Output Im.
Recommended Fuse Rating f o r M A 4100 i s 1 0 0 Amps Y ou will need to install an in-line fuse or circuit breaker in the po wer wire within 18” of the battery . This fuse or cir cuit breaker protects y our vehic le from fire in case the po wer wire shor ts to the vehic le body .
3 W arning! Y ou can mount the MA4100 in any position, even upside-down. However , yo u must maintain pr oper airflo w . Do not install your MA4100 under carpets or enclose it behind airtight panels. In trunk-mounted applications, be sure to provide venting for air circulation.
4 W arning! T o prevent a short to ground, disconnect the negative (-) terminal of the system’s battery before you begin. If the power cable shorts to ground, current will continue to flow until the short is opened, the main fuse blows, the battery explodes, or the wire melts.
5 Follow these simple instructions and ref er to the diagram belo w to make y our speaker connections: • Using at least 16 gauge wire, run wire from the speakers to the amplifier(s) using the same p.
6 Y ou can operate each pair of channels in both stereo and mono (3 channel or tri- mode) at the same time by using highpass filters (bass blockers) on the higher frequency stereo channels, and a lowpass filter (coil) on the subwoofers.
7 Input Jac ks The MA4100 includes both RCA and Mini-Din (balanced) inputs. The supplied RCA connections allow you to use the MA4100 with other brands of audio gear . Our Diff erential RCA inputs provide a dramatic impro v ement in noise reduction ov er standard RCA input types.
8 Input Gain Contr ols There are two Input Gain Controls located on the end panel under the RCA input jacks. These are not v olume controls! These controls match the output signal voltage of the source unit to the amplifier inputs.
HANDCRAFTED IN THE USA By Precision Power POWER CONNECT POWER W ARM UP 9 P o wer Side 1 3 2 1. PO WER A red light indicates that the amplifiier is turned on (After warm-up sequence). 2. W ARM UP A red light indicated that the tubes are warming up. (Refer to Pg.
10 Input/Contr ol Side L- L+ REM R+ R- L- L+ R+ R- FRONT SPEAKER OUTPUTS REAR SPEAKER OUTPUTS FRONT GAIN REAR GAIN FRONT INPUTS L R REAR INPUTS L R BALANCED INPUTS FRONT REAR DIN/RCA DIN/RCA -12dB -12dB H A N D C R A F T E D I N T H E U S A B y P r e c i s i o n P o w e r 8 9 10 11 12 17 5 4 3 26 1.
Do you have 12V at the amplifier ’s connections? 11 No Sound Is the W ARM UP LED illuminated? YES NO YES The warm up cycle can take up to 40 sec., Is there sound after that? NO Y ou’re done Is there signal on the RCA ’s? YES NO Does the amp remote (REM) have 12V? Check all connections.
12 No Sound in One Channel YES Reverse the left and right inputs. Check the pre-amp (RCA/Mini-Din) cables for open connections and make corrections. Did you find open connections? NO Y ou’re done SOUND IS NO W IN... Opposite Channel Problem is in the speaker or speaker wire of the silent channel.
Noises While the Engine is On Alternator whine: This noise changes in frequency with engine RPM. Check for: . Excessive input le vel setting on the amplifier . High resistance in cab ling or corroded and/or loose connections . P olarity of the input cab les If the problem persists, check the whines and pops chec klist below .
Check each side of the amplifier independently to see if the distortion is only on one channel. Is that the case? 14 Noises While the Engine is On or Off System hiss: Distortion: Distortion is garbled sounding music. This can often be caused by a shorted speaker wire.
15 eject VOLUME BASS TREBL E RIGHT LEFT BALANCE TR ACK REVERSE FOWARD 1 2 3 4 8 7 6 5 PPI MAR KET ING DPT Trk 1 Preamp/Equalizer Source Unit Sub Passive Crossover Passive Crossover Tweeter Tweeter Mid.
AMP RCA Rear Right Input DIF. RCA Rear Left Input INPUT ATTENUATION AMP RCA Front Right Input Left Left Right Right RCA Front Left Input MINI-DIN Front Input MINI-DIN Rear Input DIF.
Three-Y ear Limited U .S.A. W arranty This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté TUBE DRIVER MA4100 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du TUBE DRIVER MA4100 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation TUBE DRIVER MA4100, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le TUBE DRIVER MA4100 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le TUBE DRIVER MA4100, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du TUBE DRIVER MA4100.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le TUBE DRIVER MA4100. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei TUBE DRIVER MA4100 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
