Manuel d'utilisation / d'entretien du produit TL-WR743ND du fabricant TP-Link
Aller à la page of 145
TL-WR743ND 150Mbps Wireless AP/Client Router Rev: 2.0.0 1910010644.
COPYRIGHT & TRADEMARKS S pecifications are subjec t to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., L TD. Other br ands and product names are trademarks or registered trademarks of t heir respective holders.
FCC RF Radiation Exposure S t atement This equipment complies with FCC RF radiatio n exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co -located or operating in conjunction with any other antenna or transmitter .
This device has been designed to operate with the antennas listed below , and having a maximum gain of 5 dBi. Antennas not included in this list or having a gain greater than 5 dBi are strictly prohibited for use with this device. T he required antenna impedance is 50 ohms.
- IV - NCC Notice: 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功 率或變更原設計之特性及功能。 低功.
TP-LINK TECHNOLOGIES CO., L TD DECLARA TION OF CONFORMITY For the following equipment: Product Description: 150Mbp s Wireless AP/Client Router Model No.
CONTENTS Package Content s ............................................................................................................................... ...1 Chapter 1. Introduction ...................................................................
4.6.3 LAN ...................................................................................................................... 56 4.7 Wireless ..........................................................................................................
- III - 4.14 Bandwidth Control .......................................................................................................... 105 4.14.1 Control Settings .....................................................................................
TL-WR743ND 150Mbps Wireless AP/Client Router - 1 - Package Contents The following items should be found in your package: TL-WR743ND 150Mbps Wireless AP/Client Router DC Power A dapter for TL-W.
TL-WR743ND 150Mbps Wireless AP/Client Router - 2 - Chapter 1. Introduction 1.1 Overview of the Router Th e TL-WR743ND 15 0Mbps Wireless AP/Client R outer i nte gr at es 4-port Switch, Fir ew al l, NA T -R out er an d Wi re le ss AP .
TL-WR743ND 150Mbps Wireless AP/Client Router - 3 - Since the Router is compatible with virtually all the major operating systems, it is very easy to manage. Quick Setup Wizard is supported and detailed instructions are provided step by step in this user guide.
TL-WR743ND 150Mbps Wireless AP/Client Router - 4 - 1.4 Panel Layout 1.4.1 The Front Panel Figure 1-1 Front Panel sketch The Router ’s LEDs are located on the front panel (View from lef t to right). Name Statu s Indication Off Power is off. （ Power ） On Power is on.
TL-WR743ND 150Mbps Wireless AP/Client Router - 5 - Note: After a device is successfully added to the network by WPS function, the WPS LED will keep on for about 5 minutes and then turn off. 1.4.2 The Rear Panel Figure 1-2 Rear Panel sketch The following parts are lo cated on the rear panel (View from left to right).
TL-WR743ND 150Mbps Wireless AP/Client Router - 6 - INTERNET : This INTERNET port is where you will connect the DSL/cable Modem, or Ethernet. WPS: If you have client devices, such as wire less .
TL-WR743ND 150Mbps Wireless AP/Client Router - 7 - Chapter 2. Connecting the Router 2.1 System Requirement s Each PC in the LAN needs a working Ether net Adapter and an Ether net cable with RJ45 connectors TCP/IP protocol must be inst alled on each PC Web browser , such as Microsoft Internet Explorer 5.
TL-WR743ND 150Mbps Wireless AP/Client Router - 8 - a) Client Router Mode Figure 2-1 Hardware Inst allation of the TL-WR743ND in Client Rout er mode 1. Connect the notebook/PC to the LAN port of TL-WR743ND r outer with an Ethernet cable.
TL-WR743ND 150Mbps Wireless AP/Client Router - 9 - c) Repeater Mode (Range Extender) Figure 2-3 Hardware Inst allation of the TL-WR743ND in Rep eater mode 1. Plug one end of the provi ded power adapter in to the POWER jack of the router , and the other end to a standard electrical wall socke t.
TL-WR743ND 150Mbps Wireless AP/Client Router - 10 - e) Client Mode Figure 2-5 Hardware Inst allation of the TL-WR743ND in Client mod e 1. Connect the PC to the LAN port of TL -WR743ND r outer with an Ethernet cable.
TL-WR743ND 150Mbps Wireless AP/Client Router - 1 1 - Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functions of your TL-WR743ND 150Mbps Wireless AP/Client Router using Quick Setup Wiz ard within minutes.
TL-WR743ND 150Mbps Wireless AP/Client Router - 12 - Figure 3-1 Success result of Ping command If the result displayed is similar to the Figure 3-2 , it means the connec tion between your P C and the Router is failed. Figure 3-2 Failure result of Ping command Please check the connection following these step s: 1.
TL-WR743ND 150Mbps Wireless AP/Client Router - 13 - 2. Is the TCP/IP configur ation for your PC correct? Note: If the Router's IP address is 192.
TL-WR743ND 150Mbps Wireless AP/Client Router - 14 - 2. After a su ccessfully login, you can click the Quick Setup menu to quickly configure your Router . Figure 3-5 Quick Setup 3. Click Next , and then Operation Mode page will appear , as shown in Figure 3-6 .
TL-WR743ND 150Mbps Wireless AP/Client Router - 15 - Figure 3-7 W AN Connection T ype The router in Client Router mode supports three popular ways to connect to the Internet. Please select the one compatible with your ISP . 2. Click Next to enter the necessary network parameters.
TL-WR743ND 150Mbps Wireless AP/Client Router - 16 - Figure 3-9 S tatic IP Note: The IP parameters should have been provided by your ISP. IP Address - This is the W AN IP address as seen by external users on the Internet (including your ISP). Enter the IP address into the field.
TL-WR743ND 150Mbps Wireless AP/Client Router - 17 - Wireless Name of WISP S tation （ SSID ） - The SSID of the AP your Router is going to connect to as a client.
TL-WR743ND 150Mbps Wireless AP/Client Router - 18 - Figure 3-12 Note: If you know the SSID of the desired AP , you can also input it into the field "Wireless Name of WISP S tation" manually . 4. Click the Next button in Figure 3-12 , the Local Wireless AP Setting p age will appea r as below .
TL-WR743ND 150Mbps Wireless AP/Client Router - 19 - Figure 3-14 Finish Note: Y ou may click the Save button to save these settings as a text file for future reference. 3.2.2 Configuration for Router Mode When you choose Router on Operation Mode page as shown in Figure 3-6 , t ake the following steps: 1.
TL-WR743ND 150Mbps Wireless AP/Client Router - 20 - The Router provides Auto-Detect function and supports three popular ways Dynamic IP , PPPoE and Static IP to connect to the Internet. It’s re commended that you make use of the Auto-Detect function.
TL-WR743ND 150Mbps Wireless AP/Client Router - 21 - Figure 3-18 Quick Setup - S tatic IP 3. Click Next to continue, the Wireless setti ngs p age will appear as shown in Figure 3-19 . Figure 3-19 Quick Setup – Wireless Wireless Network Name (SSID) - Enter a value of up to 32 characters.
TL-WR743ND 150Mbps Wireless AP/Client Router - 22 - Figure 3-20 Quick Setup – Finish Note: Y ou may click the Save button to save these settings as a text file for future reference. 3.2.3 Configuration for Repeater Mode When you choose Repeater on Operation Mode page as shown in Figure 3-6 , take the following steps: 1.
TL-WR743ND 150Mbps Wireless AP/Client Router - 23 - Repeater Mode - Choosing WDS Repeater is to enable WDS, while choosing Univers al Repeater is to disable WDS. If WDS is enabled, all traffic from wired networks will be forwarded in the format of WDS frames consisting of four add ress fields.
TL-WR743ND 150Mbps Wireless AP/Client Router - 24 - Connect in the corresponding row . For example, the fi rst item is selected. The target network’s SSID will be automatically filled into the corresponding box whic h is shown as the Figure 3-23 .
TL-WR743ND 150Mbps Wireless AP/Client Router - 25 - Figure 3-24 Quick Setup – Network DHCP Server - Enable or Disable the server. If you disable the Server, you must have another DHCP server within your network or el se you must configure the IP address of the computer manually.
TL-WR743ND 150Mbps Wireless AP/Client Router - 26 - Figure 3-25 Quick Setup – Finish Note: Y ou may click the Save button to save these settings as a text file for future reference. 3.2.4 Configuration for Bridge with AP Mode When you choose Bridge wi th AP on Operation Mode page in Figure 3-6 , the following steps: 1.
TL-WR743ND 150Mbps Wireless AP/Client Router - 27 - Figure 3-26 Quick Setup – Wireless Bridge Setting Wireless Name of Remote AP - The SSID of the AP your Router is going to connect to as a client. You can also use the search f unction to select the SSID to join.
TL-WR743ND 150Mbps Wireless AP/Client Router - 28 - Channel - This field determines which operating frequency will be used. The default channel is set to 6. It is not necessary to change t he wireless channel unless you notice interference problems with another nearby access point.
TL-WR743ND 150Mbps Wireless AP/Client Router - 29 - Figure 3-28 Note: If you know the SSID of the desired AP , you can also input it into the field "Wireless Name of Remote AP" manually . 2. The Local Wireless AP Setti ng page will appear as shown in Figure 3-29 .
TL-WR743ND 150Mbps Wireless AP/Client Router - 30 - Figure 3-30 Quick Setup – Network DHCP Server - Enable or Disable the server. If you disable the Server, you must have another DHCP server within your network or el se you must configure the IP address of the computer manually.
TL-WR743ND 150Mbps Wireless AP/Client Router - 31 - Figure 3-31 Quick Setup – Finish Note: Y ou may click the Save button to save these settings as a text file for future reference. 3.2.5 Configuration for Client Mode When you choose Client on Operation Mode page in Figure 3 -6 , the following steps: 1.
TL-WR743ND 150Mbps Wireless AP/Client Router - 32 - Figure 3-32 Wireless Wireless Name of WISP S tation （ SSID ） - The SSID of the AP your Router is going to connect to as a client. Y ou can also use the sear ch function to select the SSID to join.
TL-WR743ND 150Mbps Wireless AP/Client Router - 33 - Click Survey button on the Wireless page as shown in Figure 3-32 , and then AP List page will appear as shown in Figure 3-33 . Find the SSID of the Access Poin t you wan t to acce ss, and click Connect in the corresponding row .
TL-WR743ND 150Mbps Wireless AP/Client Router - 34 - Figure 3-35 Quick Setup – Network DHCP Server - Enable or Disable the server. If you disable the Server, you must have another DHCP server within your network or el se you must configure the IP address of the computer manually.
TL-WR743ND 150Mbps Wireless AP/Client Router - 35 - Figure 3-36 Quick Setup – Finish Note: Y ou may click the Save button to save these settings as a text file for future reference.
TL-WR743ND 150Mbps Wireless AP/Client Router - 36 - Chapter 4. Configuring the Router This chapter will show each Web p age's ke y functions and the c onfiguration way . 4.1 Login After your successful login, you will see the sixt een main menus on the lef t of the Web-based utility .
TL-WR743ND 150Mbps Wireless AP/Client Router - 37 - Figure 4-2 Router S tatus 4.3 Quick Setup Please refer to Section 3.2: "Quick Installation Guide." 4.4 WPS This section will guide you to add a new wire less device to an existing network quickly by WPS Wi-Fi Protected Setup) function.
TL-WR743ND 150Mbps Wireless AP/Client Router - 38 - Figure 4-3 WPS WPS St atus - Enable or disable the WPS function here. Current PIN - The current value of the R outer's PIN is displayed her e. The default PIN of the Router can be found in the label or User Guide.
TL-WR743ND 150Mbps Wireless AP/Client Router - 39 - Step 2: Press and hold the WPS/QSS button of the adapter directly for 2 or 3 seconds. Step 3: W ait for a while until the next screen appears.
TL-WR743ND 150Mbps Wireless AP/Client Router - 40 - The WPS Configuration Screen of Wireless Adapter Step 3: W ait for a while until the next screen appears.
TL-WR743ND 150Mbps Wireless AP/Client Router - 41 - Figure 4-4 Add A New Device Step 2: Choose “ Press the button of the new device in two minutes ” and click Connect .
TL-WR743ND 150Mbps Wireless AP/Client Router - 42 - The WPS Configuration Screen of Wireless Adapter II. By PIN If the new device supports Wi-Fi Protected Set up and the PIN method, you can add it to the network by PIN with the following two methods.
TL-WR743ND 150Mbps Wireless AP/Client Router - 43 - The WPS Configuration S creen of Wireless Adapter Note: In this example, the default PIN code of this adapter is 13492564 as the above figure shown. Method T wo: Enter the PIN from my Router Step 1: Get the Current PI N code of the Router in Figure 4-3 (each Router has its unique PIN code.
TL-WR743ND 150Mbps Wireless AP/Client Router - 44 - Note: The default PIN code of the Router can be found in its label or the WPS configuration screen as Figure 4-3 . c). Y ou will see the following screen when the new device successfully connected to the network.
TL-WR743ND 150Mbps Wireless AP/Client Router - 45 - WISP , the Wireless port works as a W AN port at Client Router mode. The Ethernet port acts as a LAN port. Router - In this mode, the device enables multi- users to share Internet via ADSL/Cable Modem.
TL-WR743ND 150Mbps Wireless AP/Client Router - 46 - Figure 4-7 WAN – Dynamic IP This page displays the W AN IP parameters assigned dynamic ally by your ISP , including IP address, Subnet Mask, Default Gateway , etc. Click the Renew button to renew the IP parameters from your ISP .
TL-WR743ND 150Mbps Wireless AP/Client Router - 47 - Get IP w ith Unicast DHCP - A few ISPs' DHCP servers do not support the broadcast applications. If you cannot get t he IP Address normally , you can choose this option. (It is rarely required.
TL-WR743ND 150Mbps Wireless AP/Client Router - 48 - 3. If your ISP provides a PPPoE connection, select PPPoE/Russia PPPoE option. Then you should enter the following parameters ( Figure 4-9 ): Figure 4-9 W AN – PPPoE/Russia PPPoE User Name/Password - Enter the User Name and Password provided by your ISP .
TL-WR743ND 150Mbps Wireless AP/Client Router - 49 - Connect on Demand - In this mode, the Internet connection can be terminated automatically after a spec ified inactivity period ( Max Idle T ime ) and be re-established when you attempt to access the Internet again.
TL-WR743ND 150Mbps Wireless AP/Client Router - 50 - Figure 4-10 PPPoE Advanced Settings MTU Size - The default MTU size is “1480” bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP .
TL-WR743ND 150Mbps Wireless AP/Client Router - 51 - Figure 4-1 1 W AN – L2TP/Russia L2TP User Name/Password - Enter the User Name and Password provided by your ISP . These fields are case-sensitive. Dynamic IP/ St atic IP - Choose either as you are gi ven by your ISP .
TL-WR743ND 150Mbps Wireless AP/Client Router - 52 - disconnect from your Internet connection, and you will not be able to re-establish your connection automatically as soon as you attempt to access th e Internet again. T o us e this option, check the radio button.
TL-WR743ND 150Mbps Wireless AP/Client Router - 53 - If you choose static IP and enter the domai n name, you should also enter the DNS assigned by your ISP . And click the Save button. Click the Connect button to connect immediately . Click the Disconnect button to disconnect immediately .
TL-WR743ND 150Mbps Wireless AP/Client Router - 54 - Figure 4-13 User Name/Password - Enter the User Name and Password provided by your ISP . These fields are case-sensitive. Auth Server - Enter the authenticating serv er IP address or host name.
TL-WR743ND 150Mbps Wireless AP/Client Router - 55 - the number of minutes you want to have elapsed before your Internet access disconnects. Connect Automatically - The connection can be re-estab lished automatically when it was down. Connect Manually - Y ou can click the Connect / Disconnect button to connect/disconnect immediately .
TL-WR743ND 150Mbps Wireless AP/Client Router - 56 - Figure 4-14 MAC Address Clone Some ISPs require that you re gister the MAC Address of your adapter . Changes are rarely needed here. WAN MAC Address - This field displays the current MAC address of the WAN port.
TL-WR743ND 150Mbps Wireless AP/Client Router - 57 - MAC Address - The physical address of the LAN ports , as seen from the LAN. The value can't be changed. IP Address - Enter the IP address of your Router in dotted-decimal notati on (factory default: 192.
TL-WR743ND 150Mbps Wireless AP/Client Router - 58 - Figure 4-17 Wireless Settings Wireless Name of WISP S tation(SSID) - The SSID of the AP your Router is going to connect to as a client. Y ou can also use the sear ch function to select the SSID to join.
TL-WR743ND 150Mbps Wireless AP/Client Router - 59 - Local Wireless Name - Enter a value of up to 32 characters. The same N ame (SSID) must be assigned to all wireless devices in your network. Enable Wireless Router Radio - The wireless radio of the R outer can be enabled or disabled to allow wireless stations access.
TL-WR743ND 150Mbps Wireless AP/Client Router - 60 - Figure 4-18 AP List.
TL-WR743ND 150Mbps Wireless AP/Client Router - 61 - Figure 4-19 Note: If you know the SSID of the desired AP , y ou can also input it into the field " Wireless Name of WISP S tation" manually . Be sure to click the Save button to save your settings on this page.
TL-WR743ND 150Mbps Wireless AP/Client Router - 62 - Figure 4-20 Wireless Settings Wireless Network Name (also called the SSID) - Enter a value of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network.
TL-WR743ND 150Mbps Wireless AP/Client Router - 63 - 11g only - Select if all of your wireless clients are 802.11g. 11n only- Select only if all of your wireless clients are 802.11n. 11bg mixed - Select if you are using both 802.11b and 802.11g wireless clients.
TL-WR743ND 150Mbps Wireless AP/Client Router - 64 - MAC Address of Remote AP (BSSID) - The BSSID of the AP y our Router is going to connect to as a client. You can also use the s earch function to select the BSSID to join. Survey - Click this button, you can survey t he AP which runs in the current channel.
TL-WR743ND 150Mbps Wireless AP/Client Router - 65 - Figure 4-21 Wireless Settings Repeater Mode - Choosing WDS Repeater is to enabl e WDS, while choosing Universal Repeater is to disable WDS. Wireless Name of Root AP - The SSID of the AP your Rout er is going to connect to as a client.
TL-WR743ND 150Mbps Wireless AP/Client Router - 66 - 2. Failure to follow these gui delines can result in significant performance degradation or ina bility to wirelessly connect to the Router .
TL-WR743ND 150Mbps Wireless AP/Client Router - 67 - Key Format - Hexadecimal and ASCII formats are provided here . Hexadecima l format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. ASCII format stands for any combination of keyboa rd characters in t he specified length.
TL-WR743ND 150Mbps Wireless AP/Client Router - 68 - In an elevated location such as a high shelf. Away from the potential sources of interfer ence, such as PCs, microwaves, and cordless phones. With the Antenna in the upright position. Away from large metal surfaces.
TL-WR743ND 150Mbps Wireless AP/Client Router - 69 - Near the center of the area in which your wireless stations will operate. In an elevated location such as a high shelf. Away from the potential sources of interfer ence, such as PCs, microwaves, and cordless phones.
TL-WR743ND 150Mbps Wireless AP/Client Router - 70 - Disable Security - If you do not want to use wireless securi ty, check this radio button. But it’s strongly recommended to choose one of t he following modes to enable security. WP A/WP A2 - Personal(Recommended) - It’s the WPA/WPA2 authentication type based on pre-shared passphrase.
TL-WR743ND 150Mbps Wireless AP/Client Router - 71 - Figure 4-26 Radius Server IP - Enter the IP address of the Radius server. Radius Port - Enter the port number of the Radius server. Radius Password - Enter the password for the Radius server.
TL-WR743ND 150Mbps Wireless AP/Client Router - 72 - 64-bit - You can enter 10 hexadecimal digits (any co mbination of 0-9, a-f, A-F, zero key is not promoted) or 5 ASCII characters. 128-bit - You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 13 ASCII characters.
TL-WR743ND 150Mbps Wireless AP/Client Router - 73 - Figure 4-29 Add or Modify Wireless MAC Address Filtering entry To add or modify a MAC Address Filtering entry, follo w these instructions: 1. Enter the appropriate MAC Address into the MAC Address field.
TL-WR743ND 150Mbps Wireless AP/Client Router - 74 - 3. Delete all or disable all en tries if there are any entries already. 4. Click the Add New... button. 1) Enter the MAC address 00-0A-EB-B 0-00-0B/00-0 A-EB-00-07-5 F in the MAC Address field. 2) Enter wireless station A/B in the Description field.
TL-WR743ND 150Mbps Wireless AP/Client Router - 75 - particular receiving station and negotiate the s ending of a data frame. The default value is 2346. Fragmentation Threshold - This value is the maximum size determining whether packets will be fragmented.
TL-WR743ND 150Mbps Wireless AP/Client Router - 76 - Current Status - The connected wireless stati on's running status, one of STA - AUTH/ ST A- ASS O C/ S T A- JO I NE D / W P A/ W P A- PS K .
TL-WR743ND 150Mbps Wireless AP/Client Router - 77 - Figure 4-33 DHCP Setting s DHCP Server - Enable or Disable the DHCP server . If you disable the Server , you must have another DHCP server within your network o r else you must configure the computer manually .
TL-WR743ND 150Mbps Wireless AP/Client Router - 78 - 4.8.2 DHCP Clients List Choose menu “ DHCP → DHCP Client s List ”, and then you can view the information about the clients attach ed to the Router in the screen as shown in Figure 4-34 .
TL-WR743ND 150Mbps Wireless AP/Client Router - 79 - Reserved IP Address - The IP address reserved for the PC by the Router. Status - The status of this entry, either Enabled or Disabled . To Reserve an IP address: 1. Click the Add New… button.
TL-WR743ND 150Mbps Wireless AP/Client Router - 80 - There are four submenus under the Forwar ding menu (shown in Figure 4-37 ): Virtual Servers , Port T riggering , DMZ and UPnP . Click any of them, and you will be able to configure the corresponding function.
TL-WR743ND 150Mbps Wireless AP/Client Router - 81 - 3. T ype the IP Address of the computer in the IP Address box. 4. Select the protocol used for this application, either TCP , UDP , or All . 5. Select the Enable to enable the virtual server . 6. Click the Save button.
TL-WR743ND 150Mbps Wireless AP/Client Router - 82 - 4.9.2 Port Triggering Choose menu “ Forwarding → Port T riggering ”, and then you can view and add port triggerin g in the screen as shown in Figure 4-40 . Some applications require multiple connections, like Internet games, video conferenci ng, Internet calling and so on.
TL-WR743ND 150Mbps Wireless AP/Client Router - 83 - 1. Click the Add New… button, the next screen will pop-up as shown in Figure 4-41 . 2. Select a common application from the Common Applications drop-down list, then the T rigger Port field and the Incoming Ports field will be automatic ally filled.
TL-WR743ND 150Mbps Wireless AP/Client Router - 84 - 3. Incoming Port Range cannot overlap each other. 4.9.3 DMZ Choose menu “ Forwarding → DMZ ”, and then you can view and configure DMZ host in the screen as shown in Figure 4-42 .
TL-WR743ND 150Mbps Wireless AP/Client Router - 85 - Figure 4-43 UPnP Current UPnP Status - UPnP can be enabled or disabled by clicking the Enable or Dis able button. Current UPnP Settings List - This table displays the current UPnP information.
TL-WR743ND 150Mbps Wireless AP/Client Router - 86 - 4.10.1 Basic Security Choose menu “ Security → Basic Securit y ”, and then you can configure the basic security in the screen as shown in Figure 4-45 . Figure 4-45 Basic Security Firewall - A firewall protects your network from the outside world.
TL-WR743ND 150Mbps Wireless AP/Client Router - 87 - L2TP Passthrough - Layer 2 Tunneling Protocol (L2T P) is the method used to enable Point-to-Point sessions via the Internet on the Layer 2 level. To allow L2TP tunnels to pass through the Router, keep the default, Enabled .
TL-WR743ND 150Mbps Wireless AP/Client Router - 88 - Figure 4-46 Advanced Security Packets Statistics Interval (5~60) - The default value is 10. Se lect a value between 5 and 60 seconds from the drop-down list. The Packets S tatistics Interval value indicates the time section of the p ackets statistics.
TL-WR743ND 150Mbps Wireless AP/Client Router - 89 - UDP-FLOOD Packets Threshold (5~3600) - The default value is 500. Enter a value between 5 ~ 3600. When the current U PD-FLOOD Packets number is beyond the set value, the Router will startup the bl ocking function immediately.
TL-WR743ND 150Mbps Wireless AP/Client Router - 90 - the Setup page of the Router's W eb-Based Utility locally from insi de the network, c heck the radio button “ Only the PCs listed can browse the built-in w eb pages to perform Administrator tasks ”, and then enter each MAC Address in a separate field.
TL-WR743ND 150Mbps Wireless AP/Client Router - 91 - please enter http://202.96.12.8:8080 in your browser. Later, you may be asked for the Router's password. After successfully entering the usernam e and password, you will be able to access the Router's w eb-based utility.
TL-WR743ND 150Mbps Wireless AP/Client Router - 92 - 2. Enter the MAC address of the PC (e.g. 00-11-22 -33-44-AA) you’d like to control in the MAC Address of Child PC field. Or you can choos e the MAC address from the All Address in Current LAN drop-down list.
TL-WR743ND 150Mbps Wireless AP/Client Router - 93 - Figure 4-50 Add or Modify Parental Co ntrol Entry For example : If you desire that the child PC with MAC address 00-11-22-33-44-AA can access www.google.com on Saturday only while the parent PC with MAC addres s 00-11-22-33-44-BB is without any restriction, you should follow the settings below.
TL-WR743ND 150Mbps Wireless AP/Client Router - 94 - In Status field, select Enable. 4. Click Save to complete the settings. Then you will go back to the Parental Control Settings page and see t he following list, as shown in Figure 4-51 . Figure 4-51 Parental Control Settings 4.
TL-WR743ND 150Mbps Wireless AP/Client Router - 95 - Figure 4-53 Access Control Rule Management Enable Internet Access Control - Select the check box to enable the Internet Access Control function, so the Default Filter Policy can take effect. Rule Name - Here displays the name of the rule and this name is unique.
TL-WR743ND 150Mbps Wireless AP/Client Router - 96 - 5. Select a schedule from the Schedule drop-down list or choose “ Click Here To Add New Schedule ”. 6. In the Action field, select Deny or Allow . 7. In the Status field, select Enabled or Disabled to enable or disable your entry.
TL-WR743ND 150Mbps Wireless AP/Client Router - 97 - 3. Click “ Acce ss Control → Schedule ” in the left to enter the Schedule Settings page. Add a new entry with the Schedule Description is Schedule_1, Day is Sat and Sun, Start Time is 1800 and Stop Time is 2000.
TL-WR743ND 150Mbps Wireless AP/Client Router - 98 - To add a new entry, please follow the steps below. 1. Click the Add New… button. 2. In the Mode field, select IP Address or MAC Address. If you select IP Addre ss, the screen shown is Figure 4-56 .
TL-WR743ND 150Mbps Wireless AP/Client Router - 99 - 3. In Host Description field, create a unique description for the host (e.g. Host_1). 4. In MAC Address field, enter 00-11-22-33-4 4-AA. 5. Click Save to complete the settings. Then you will go back to the Host Se ttings page and see the following list.
TL-WR743ND 150Mbps Wireless AP/Client Router - 100 - 1) In Target Description field, create a unique description for the target (e.g. Target_1). 2) In Domain Name field, enter the domain name in the blank. You can enter 4 domain names. 3. Click the Save button.
TL-WR743ND 150Mbps Wireless AP/Client Router - 101 - 1. Click Add New… button in Figure 4- 58 to enter the Add or Modify an Access Targe t Entry page. 2. In Mode field, select Domain Name from the drop-down list. 3. In Target Description field, create a unique description fo r the target (e.
TL-WR743ND 150Mbps Wireless AP/Client Router - 102 - 4. In Time field, you can select all day-24 hours or you may enter the Start Time and Stop Time in the corresponding field. 5. Click Save to complete the settings. Click the Delete All button to delete all the entries in the table.
TL-WR743ND 150Mbps Wireless AP/Client Router - 103 - 4.13 Advance d Routing Figure 4-63 Advanced Routing There are two submenus under the Advanced Routing menu as shown in Figure 4-63 : Stati c Routing List and System Routing T able. Click any of them, and you w ill be able to configure the corresponding function.
TL-WR743ND 150Mbps Wireless AP/Client Router - 104 - 2. Enter the following data: Destination Network - The Destination Network is the address of the netwo rk or host that you want to assign to a static route.
TL-WR743ND 150Mbps Wireless AP/Client Router - 105 - Subnet Mask - The Subnet Mask determines which por tion of an IP address is the network portion, and which portion is the host portion. Gateway - This is the IP address of the gateway device that a llows fo r contact between the Router and the network or host.
TL-WR743ND 150Mbps Wireless AP/Client Router - 106 - Note: For optimal control of the bandwi dth, please select the right bandwidth type and ask your ISP for the total bandwidth of the egress and ingress.
TL-WR743ND 150Mbps Wireless AP/Client Router - 107 - Figure 4-70 Bandwidth Control Rule Settings Step 3: Click the Save button. 4.15 IP& MAC Bing Setting Figure 4-71 the IP & MAC Binding menu There are two submenu s under the IP &MAC Binding menu (shown in Figure 4-71 ): Binding Settings and ARP List .
TL-WR743ND 150Mbps Wireless AP/Client Router - 108 - IP Address - The assigned IP address of the cont rolled computer in the LAN. Bind - Check this option to enable ARP binding for a specific device. Modify - To modify or del ete an existing entry.
TL-WR743ND 150Mbps Wireless AP/Client Router - 109 - Figure 4-74 Find IP & MAC Binding Entry Click the Enable All button to make all entries enabled.
TL-WR743ND 150Mbps Wireless AP/Client Router - 1 10 - Click the Load All button to load all items to the IP & MAC Bind ing list. Click the Refresh button to refresh all items. Note: An item could not be loaded to the IP & MAC Binding list if the IP address of the item has been loaded before.
TL-WR743ND 150Mbps Wireless AP/Client Router - 1 1 1 - 2. T ype the Password for your DDNS account. 3. T ype the Domain Name you received from dynamic DNS service provi der . 4. Click the Login button to log in the DDNS service. Connection Status - The status of the DDNS servic e connection is displayed here.
TL-WR743ND 150Mbps Wireless AP/Client Router - 1 12 - 4.16.3 Comexe.cn DDNS If the dynamic DNS Service Provider you select is www.comexe.cn , the page will appear as shown in Figure 4-78 . Figure 4-78 Comexe.cn DDNS Settings To set up for DDNS, follow these instructions: 1.
TL-WR743ND 150Mbps Wireless AP/Client Router - 1 13 - 4.17 System T ools Figure 4-79 T he System T ools menu Choose menu “ System T ools ”, and then you can s ee the s ubmenus under t he main menu: Ti me Settings , Diagnostic , Firmw are Upgrade , Factory Default s, Backup & Restore, Reboot, Password, System Log and St atistics.
TL-WR743ND 150Mbps Wireless AP/Client Router - 1 14 - Time Zone - Select your local time zone from this pull down list. Date - Enter your local date in MM/ DD/YY into the right blanks. Tim e - Enter your local time in HH/MM/SS into the right blanks.
TL-WR743ND 150Mbps Wireless AP/Client Router - 1 15 - Note: 1. This setting will be used for some time-based fu nctions such as firewall. Y ou must specify your time zone once you login to the router successfully , otherwise, these functions will not take ef fect.
TL-WR743ND 150Mbps Wireless AP/Client Router - 1 16 - Y ou can use ping/traceroute to test both numeric IP address or domain name. If pinging/tracerouting the IP address is successf ul, but pinging/tracerout ing the domain name is not, you might have a name resolution problem .
TL-WR743ND 150Mbps Wireless AP/Client Router - 1 17 - Figure 4-84 Firmware Upgrade Firmware Version - This displays the current firmware version. Hardware Version - This displays the current hardware version. The hardware version of the upgrade file must accord with the R outer’s current hardware version.
TL-WR743ND 150Mbps Wireless AP/Client Router - 1 18 - Figure 4-85 Restore Factory Default Click the Restore button to reset all configuration settings to their default values. The default User Name : admin The default Password : admin The default IP Address : 192.
TL-WR743ND 150Mbps Wireless AP/Client Router - 1 19 - 4.17.6 Reboot Choose menu “ System T ools → Reboot ”, and then you can click the Reboot button to reboot the Router via the next screen.
TL-WR743ND 150Mbps Wireless AP/Client Router - 120 - It is strongly recommended that you should change the factor y default user name and passwor d of the Router, because all users who try to access the Router's Web-based utility or Quick Setup will be prompted for the Router's default user name and password.
TL-WR743ND 150Mbps Wireless AP/Client Router - 121 - Figure 4-90 Mail Account Settings From - Your mail box address. The Router would connect it to send logs. To - Recipient’s address. The destination mail box where the logs would be received.
TL-WR743ND 150Mbps Wireless AP/Client Router - 122 - Log Level - By selecting the log level, only l ogs of this level will be shown. Refresh - Refresh the page to show the latest log list. Save Log - Click to save all the logs in a txt file.
TL-WR743ND 150Mbps Wireless AP/Client Router - 123 - Click Delete All to delete all entries in the table. Statistics Table: IP A ddress/MAC Addre ss T he IP Address and MAC address are displa yed with related statistics Packets The number of packets received an d transmitted by the Router.
TL-WR743ND 150Mbps Wireless AP/Client Router - 124 - Appendix A: FAQ 1. How do I configure the Router to access the Internet b y ADSL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your AD SL Modem to the W AN port on the Router .
TL-WR743ND 150Mbps Wireless AP/Client Router - 125 - 2. How do I configure the Router to access the Internet b y Ethernet users? 1) Log in to th e Router , click the “ Netw ork ” menu on the left of your browser , and click " WA N " subm enu.
TL-WR743ND 150Mbps Wireless AP/Client Router - 126 - Figure A-4 V irtual Servers Figure A-5 Add or Modify a Virtual server Entry Note: Your opposite side should call your WAN IP , which is displayed on the “Status” page.
TL-WR743ND 150Mbps Wireless AP/Client Router - 127 - Figure A-7 Basic Security 4. I want to build a WEB Server on the LAN, w hat should I do? 1) Because the WEB Server port 80 will inte rfere with the WEB management port 80 on the Router , you must change the WEB management port number to avoid interference.
TL-WR743ND 150Mbps Wireless AP/Client Router - 128 - Figure A-8 Remote Management Note: If the above configuration takes effect, configure to the Router by typing 19 2.168.0.1:88 (the Router’s LAN IP address: Web Management Port) in t he address field of the Web browser.
TL-WR743ND 150Mbps Wireless AP/Client Router - 129 - Figure A-1 0 Add or Modify a Virtual server Entry 5. The wireless st ations cannot connect to the Router . 1) Make sure the " Enable Wireless Router Radio " is checked. 2) Make sure that the wireless stations' SSID accord with the Router's SSID.
TL-WR743ND 150Mbps Wireless AP/Client Router - 130 - Appendix B: Configuring the PC In this section, we’ll introduce how to inst all and configure the TCP/IP correctly in Windows XP . First make sure your Ethernet Adapter is work ing, refer to the adapter ’s manual if necessary .
TL-WR743ND 150Mbps Wireless AP/Client Router - 131 - Figure B-2 5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default.
TL-WR743ND 150Mbps Wireless AP/Client Router - 132 - Figure B-3 Note: For Windows 98 OS or before, the PC and Router may need to be restarted. Setting IP address manually 1 Select Use the following IP address radio button. And the fo llowing items available 2 If the Router's LAN IP addr ess is 192.
TL-WR743ND 150Mbps Wireless AP/Client Router - 133 - Figure B-4 Now: Click OK to keep your settings..
TL-WR743ND 150Mbps Wireless AP/Client Router - 134 - Appendix C: Specifications General S tandards IEEE 802.3, 802.3u, 802.3x, 802.1x , 802.1 1n, 802.1 1b, 802.
TL-WR743ND 150Mbps Wireless AP/Client Router - 135 - Appendix D: Glossary 802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output).
TL-WR743ND 150Mbps Wireless AP/Client Router - 136 - PPPoE ( P oint to P oint P rotocol o ver E thernet) - PPPoE is a protocol for connecting remote hosts to the Internet over an always-on connection by simulating a dial-up connection.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté TP-Link TL-WR743ND c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du TP-Link TL-WR743ND - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation TP-Link TL-WR743ND, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le TP-Link TL-WR743ND va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le TP-Link TL-WR743ND, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du TP-Link TL-WR743ND.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le TP-Link TL-WR743ND. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei TP-Link TL-WR743ND ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
