Manuel d'utilisation / d'entretien du produit TL-WR542G du fabricant TP-Link
Aller à la page of 69
User Guide TL-WR542G 54Mbp s Wireless Router.
TL-WR542G 54M Wireless Router User Guide - 1 - COPYRIGHT & TRADEMARKS S pecifications ar e subject to change without n otice. is the registered trademark of TP-LINK T echnologies Co., Lt d. Other brands and product names are trademarks or registered trademarks of their respective holders.
TL-WR542G 54M Wireless Router User Guide - 2 - Package cont ents .............................................................................................................. 4 Chapter 1: About this Guide .............................................
TL-WR542G 54M Wireless Router User Guide - 3 - 5.8.1 Fir ewall ................................................................................................................. ......... 39 5.8.2 IP Addr e ss Filtering ................................
TL-WR542G 54M Wireless Router User Guide - 4 - Package contents The following contents should be found in your box: • One TL-WR542G 54Mbp s Wireless Router • One AC power Adapter for TL-WR542G 54M.
TL-WR542G 54M Wireless Router User Guide - 5 - Chapter 1: About this Guide Thank you for choosing the TL-WR542 G 54Mbp s Wireless Router . The Ro uter provides dedicated solution for Small Office/Home Of fice (SOHO) network.
TL-WR542G 54M Wireless Router User Guide - 6 - Chapter 2: Introduction 2.1 Overview of the Router The TL-WR542G 54Mbps Wireless Router integr ates firewall, NA T -router and Wireless AP . It s design is dedicated to Small Offi ce/Home Office ( SOHO) Wireless network solution.
TL-WR542G 54M Wireless Router User Guide - 7 - • Provides WP A and WP A-PSK authentication and TKIP/AES encryption security • Provides wireless LAN ACL (Access Control List) filtering • Built-in.
TL-WR542G 54M Wireless Router User Guide - 8 - 2.3.2 The Rear Panel The Rear panel contains the following f eatures. (V iewed from left to right:) • Wireless antenna • Factory Default Reset button There are two ways to reset the Router's factory defaults: 1.
TL-WR542G 54M Wireless Router User Guide - 9 - Chapter 3: Connecting the Router 3.1 System Requirement s Broadband Internet Access Service (DSL/Cable/Ethernet) One DSL/Cable modem that has RJ4.
TL-WR542G 54M Wireless Router User Guide - 10 - To L A N Switch/Hub 4 3 2 1 WAN To WA N RESE T （） XDSL C abl e Et her ne t 、、 Figure 3-1: Physical Installation of the TL-WR542G 54Mbps Wireless.
TL-WR542G 54M Wireless Router User Guide - 11 - Chapter 4: Quick Installation Guide After connecting the TL-WR542G Router into y our network, you should configure it. This chapter describes how to c onfigure t he basic functions of your TL-WR542G Wireless Router .
TL-WR542G 54M Wireless Router User Guide - 12 - Figure 4-1: Successful result of Ping command Congratulations! The connection between your PC and the Router has been established. If the result displayed similar to that shown in Figure 4-2: Figure 4-2: Failed result of Ping command It means that your PC has not connected to the Router .
TL-WR542G 54M Wireless Router User Guide - 13 - Figure 4-4: Login Windows If the User Name and Password are correc t, the Setup Wizard page will appear , shown in figure 4-5.
TL-WR542G 54M Wireless Router User Guide - 14 - 1) If you choose " PPPoE ", you will see this page shown in figure 4-7: Figure 4-7: Setup Wizard - PPPoE User Name and Password - Enter the User Name and Password provided by your ISP. These fields are case s ensitive.
TL-WR542G 54M Wireless Router User Guide - 15 - Figure 4-9: Setup Wizard - Wireless settings In the page, you can configure the follow wireless parameter: Wireless Radio - indicates whether the Access Point feature of the Router is enabled or not.
TL-WR542G 54M Wireless Router User Guide - 16 - Chapter 5: Configuring the Router This chapter describes eac h web page's key functions. 5.1 login After your successful login, you can confi gure and manage the Router . There are ten main menus on the left of the web- based utility .
TL-WR542G 54M Wireless Router User Guide - 17 - Figure 5-1: Router status 5.3 Setup Wizard Please refer to Section 4.2: "Quick Installation Guide.
TL-WR542G 54M Wireless Router User Guide - 18 - There are three submenus under the Network menu (shown in figure 5-2): LAN , WA N and MAC Clone. Click any of them, and you can conf igure the corresponding function. The detailed explanations for ev ery submenu are provided below .
TL-WR542G 54M Wireless Router User Guide - 19 - Figure 5-4 WAN - DHCP This page displays the W AN IP pa ramete rs assigned dynamically by your ISP , including IP address, Subnet Mask, Default Gateway , etc. Click Renew button to renew the IP parameters from your ISP .
TL-WR542G 54M Wireless Router User Guide - 20 - Figure 5-4a: W A N - 802.1X + DHCP • User Name - Enter the user name for 802.1x authentication provided by your ISP • Password - Enter the password for 802.1x authentication provided by your ISP. Click Login button to start 802.
TL-WR542G 54M Wireless Router User Guide - 21 - MTU. But this is rarely required, and should not be done unless you are sure it is necessary for your ISP connection. Primary DNS : Optional, type the D NS address in dotted-decimal notation provided by your ISP .
TL-WR542G 54M Wireless Router User Guide - 22 - Figure 5-6: WAN - PPPoE User Name/Passwo rd : Enter the User Name and Password provided by your ISP . These fields are case-sensitive. Connect on Demand : Y ou can configure the Rout er to disconnect your Internet connection after a specified period of inactivity ( Max Idle Time ).
TL-WR542G 54M Wireless Router User Guide - 23 - Figure 5-7: PPPoE Advanced Settings Packet MTU : The default MTU size is usually fine. The normal MTU (Maximum T ransmission Unit) value for most Ether net networks is 1492 bytes. For some ISPs, you need modify the MTU.
TL-WR542G 54M Wireless Router User Guide - 24 - Figure 5-8: MAC Address Clone Some ISPs require that you register t he MAC Address of your adapter, which is connected to your cable or DSL modem during installation. Usually, Don’t change anything here.
TL-WR542G 54M Wireless Router User Guide - 25 - 5.5.1 Wireless Settings The basic settings for Wireless network are set on this page, figure 5-10: Figure 5-10: Wireless Settings SSID - Enter a value of up to 32 characters. The same name (SSID) must be assigned to all wireless devices in your network.
TL-WR542G 54M Wireless Router User Guide - 26 - Enable Wireless Router Radio - The wireless radio of this Router can be enabled or disabled to allow wireless stations a ccess. If enabled, wireless stations will be able to access the Router, otherwise, wire less stations will not be able to access the Router.
TL-WR542G 54M Wireless Router User Guide - 27 - WPA-PSK Passphrase – You can enter a WPA passphrase between 8 and 6 3 characters long. Group Key Update Period - Specify the group key updat e interval in seconds. The value can be either 0 or at least 30.
TL-WR542G 54M Wireless Router User Guide - 28 - accessing the Router, which depend on the station's MAC addresses. • MAC Address - The wireless station's MAC address that you want to access control. • Description - A simple description of the wireless station.
TL-WR542G 54M Wireless Router User Guide - 29 - any combination of hexadecimal digits (0 -9, a-f, A-F) in specified length. For example: 2F34D20BE2. 5. Statu s - Select Enabled or Disabled for this entry on the Status pull-down list. 6. Click the Save button to save this entry .
TL-WR542G 54M Wireless Router User Guide - 30 - access the Router, however, other wireless stations that are not in the list can access the Router. Note : If you enable the function and select the Den.
TL-WR542G 54M Wireless Router User Guide - 31 - Figure 5-14: the DHCP menu There are three submenus under the DH CP menu (shown in figure 5-14): DHC P Settings , DHCP Client s List and Address Reservation. Click any of them, and yo u can configure the corresponding function.
TL-WR542G 54M Wireless Router User Guide - 32 - consult your ISP. Secondary DNS: Optional. You can input the IP address of another DNS server if your ISP provides two DNS servers. Note: To use the DHCP server function of the Router, you must configure all computers on the LAN as "Obtain an IP A ddress automatically" mode.
TL-WR542G 54M Wireless Router User Guide - 33 - Figure 5-17: Address Reservation MAC Address – The MAC address of the PC that you want to reserve IP Address. Assigned IP Address –The IP Address of Router reserved. To Reserve IP addresses: 1.
TL-WR542G 54M Wireless Router User Guide - 34 - 5.7 Forwarding Figure 5-18: the Forwarding menu There are four submenus under the Fo rwarding menu (shown in figure 5-18): Vi rt ua l Servers , Port T riggering , DMZ and UPnP . Click any of them, and you can configure the corresponding function.
TL-WR542G 54M Wireless Router User Guide - 35 - IP Address - The IP Address of the PC running the service application Protocol - The protocol used for th is application, either TCP or UDP , or All (include all protocol that can be accessed by the Router).
TL-WR542G 54M Wireless Router User Guide - 36 - 5.7.2 Port T riggering Some applications require multiple connections, like Internet games, video conferencing, Internet telephoning and so on. These applications cannot work with a pure NAT router. Port Triggering is used for some of these applications that can work with an NAT router.
TL-WR542G 54M Wireless Router User Guide - 37 - UDP , or ALL (include all protocol that can be access the Router). Enable - The Enable checkbox to enable por t forwarding for the application. Common Applications – some p opular applications already existing in the pull-down list.
TL-WR542G 54M Wireless Router User Guide - 38 - forwards all the ports at the same time. An y PC whos e port is being forwarded must have its DHCP client function disabled and should have a new static IP Address assigned to it because its IP Address may change when usi ng the DHCP function.
TL-WR542G 54M Wireless Router User Guide - 39 - UPnP device currently accessing the Router . • Ext. Port – external port, the device has opened for Router . • Protocol – what type of protocol is opened. • Int. Port – Internal port, the device has opened for local host.
TL-WR542G 54M Wireless Router User Guide - 40 - Figure 5-24: Firewall Settings Enable Firew all – the general firewall switch is on or off. Enable IP Address Filtering – set IP Address Filteri ng is enabled or disabled. There are two default filtering rules of IP A ddress Filtering, either Permit or Prevent accessing the Router.
TL-WR542G 54M Wireless Router User Guide - 41 - Figure 5-25: IP address Filtering To disable the IP Address Filteri ng feature, keep t he default setting, Disabled . To set up an IP Address Filt ering entry, click Enable Firewall and Enable IP Address Filtering on the Firewall page, and click the Add New… button.
TL-WR542G 54M Wireless Router User Guide - 42 - 4. WAN Port - type a WAN Port or a range of WA N Port in the field. Leave the field blank, which means all WAN Po rt have been put into the field. For example, 25 – 110. 5. Protocol - select which protocol is to be used, either TCP or UDP , or All (Both TCP and UDP).
TL-WR542G 54M Wireless Router User Guide - 43 - Figure 5-27: Domain Filtering Before adding a Domain Filtering e ntry, you must ensure that Enable Firewall and Enable Domain Filtering have been selected on the Firewall page. To Add a Domain filtering entry, clicking Add New… button.
TL-WR542G 54M Wireless Router User Guide - 44 - Click the Next button to go to the next page and the Previous button to return to the previous page. For example, if you want to block t he PCs on your LAN to access websites www.xxyy.com.cn , www.aabbcc.
TL-WR542G 54M Wireless Router User Guide - 45 - Figure 5-30: Add or Modify a MAC Address Filtering entry To add or modify a MAC Address Filter ing entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit).
TL-WR542G 54M Wireless Router User Guide - 46 - feature allows you to manage your Router fr om a remote location, via the Internet. Figure 5-31: Remote Management Web Management Port - Web browser access normally uses the standard HTTP service port 80.
TL-WR542G 54M Wireless Router User Guide - 47 - Figure 5-32: Advanced Security settings Packets S tatistic interval (5 ~ 60) - The default value is 10. Select a value between 5 and 60 seconds in the pull-down list. The Packets S t atistic i nterval value indicates the time section of the packe ts statistic.
TL-WR542G 54M Wireless Router User Guide - 48 - Ignore Ping Packet from W AN Port – Enable or Disable ignore ping packet from W A N port. The default is disabled.
TL-WR542G 54M Wireless Router User Guide - 49 - Figure 5-34: S tatic Routing T o add static route entries: 1. Enter the following data: • Destination IP Address - The Destination IP Address is the address of the network or host that you want to assign to a static route.
TL-WR542G 54M Wireless Router User Guide - 50 - using this feature, you need to sign up for DDNS service provider s such as www.oray.net or www.comexe.cn . The Dynamic DNS client service provider will give you a password or key. To set up for DDNS, follow these instructions: 5.
TL-WR542G 54M Wireless Router User Guide - 51 - Figure 5-36: Comexe.cn DDNS Settings To set up for DDNS, follow these instructions: 1. T ype the domain names your dynamic DNS service provider gave. 2. T ype the User Name for your DDNS account. 3. T ype the Password for your DDNS account.
TL-WR542G 54M Wireless Router User Guide - 52 - every submenu are provided below . 5.1 1.1 Time Y ou can set time manuall y or get GMT from In ternet for the Router on this page (shown in figure 5-38): Figure 5-38: T ime settings Time Zone : Select your local time zone from this pull down list.
TL-WR542G 54M Wireless Router User Guide - 53 - Figure 5-39: Firmware Upgrade New firmware versi ons are posted at www.tp-link.com and can be downloaded free. If the Router is not experienci ng difficulties, there is no need to downl oad a more recent firmware version, unless that version has a new feature that you want to use.
TL-WR542G 54M Wireless Router User Guide - 54 - Figure 5-40: Restore Factory Default Click the Restore Factory Defaults button to reset all confi guration settings to their default values. • The default User Name : admin • The default Passw ord : admin • The default IP Address : 192.
TL-WR542G 54M Wireless Router User Guide - 55 - Figure 5-42: Password It is strongly recommended that you change t he factory default u ser name and password of the Router. All users who try to access t he Router's web-based ut ility or Setup Wizard will be prompted for the Router 's user name and password.
TL-WR542G 54M Wireless Router User Guide - 56 - Figure 5-44: S tatistics Current Statistics Status : Enable or Disable. The default value is disabled. To enable, click the Enable button. If disabled, the f unction of DoS protection in Security settings will be ineffective.
TL-WR542G 54M Wireless Router User Guide - 57 - Appendix A: F AQ 1. How to configure the Router to access Internet by ADSL users? 1) First, configure the ADSL modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from yo ur ADSL modem to the W AN port on the Router .
TL-WR542G 54M Wireless Router User Guide - 58 - Figure A-1: Virtual Server Note : Y our opposite side should call your W AN IP , which is displayed on the “S tatus” page. 4) How to enable DMZ Host: Log into the Router , click the “Forwarding” menu on the left of your browser , and click " DMZ" submenu.
TL-WR542G 54M Wireless Router User Guide - 59 - Figure A-3: Remote Management Note : T ype http://192.168.1.1:88 into browser to log into the Router if the abo ve configuration takes ef fect. 3) Log into the Router , click the “Forwarding” men u on the left of your browser , an d click " Virtual Servers" submenu.
TL-WR542G 54M Wireless Router User Guide - 60 - Appendix B: Configuring the PCs In this section, we’ll introduce how to inst all and configure the TCP/IP correctly in Windows 95/98. First make sure your Ethernet Adapter is working, refer to the adapter ’s manual if needed.
TL-WR542G 54M Wireless Router User Guide - 61 - 1) On the Windows taskbar , click the Star t button, point to Settings , and then click Control Panel . 2) Double-click the Netw ork icon, highlight the bound TCP/IP tab in the appearing Netw ork window .
TL-WR542G 54M Wireless Router User Guide - 62 - Figure B-4: IP Address tab b. Do not type anything into the N ew g at ewa y field on the Gatew ay t ab.
TL-WR542G 54M Wireless Router User Guide - 63 - a. Select S pecify an IP address on IP Address tab, as shown in the following figure. If the Router's LAN IP addr ess is 192.168.1.1 type IP address is 192.168.1.x (x is from 2 to 254), Subnet mask is 255.
TL-WR542G 54M Wireless Router User Guide - 64 - c. On the DNS Configuration tab, click Enable DNS radio, and type your computer name in to the Host field and a Domain (such as szonline.
TL-WR542G 54M Wireless Router User Guide - 65 - Appendix C: S pecifications General S tandards IEEE 802.3, 802. 3u, 802.1 1b and 802.1 1g Protocols TCP/IP , PPPoE, DHCP , ICMP , NA T , SNTP Channel 13.
TL-WR542G 54M Wireless Router User Guide - 66 - Appendix D: Glossary 2x to 3x eXtended Range TM WLAN Transmission Technology - The WLAN device with 2x to 3x eXtended Range TM WLAN transmission technology ma ke its sensitivity up to 105 dB, which gives users the ability to have robust, longer-range wire less connections.
TL-WR542G 54M Wireless Router User Guide - 67 - PPPoE ( P oint to P oint P rotocol o ver E thernet) - PPPoE is a pr otocol for connecting remote hosts to the Internet over an al ways-on connection by simulating a dial-up connection.
TL-WR542G 54M Wireless Router User Guide - 68 - Appendix E: Contact Information For help with the installation or operat ion of the TP-LINK TL-WR542G 54Mbps Wireless Router, please contact us. Tel: +86-755-2661-2350, 2652-5723 Fax: +86-755-2663-6921 E-mail: export@tp-link.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté TP-Link TL-WR542G c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du TP-Link TL-WR542G - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation TP-Link TL-WR542G, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le TP-Link TL-WR542G va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le TP-Link TL-WR542G, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du TP-Link TL-WR542G.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le TP-Link TL-WR542G. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei TP-Link TL-WR542G ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
