Manuel d'utilisation / d'entretien du produit tl-sl5428e du fabricant TP-Link
Aller à la page of 259
TL-SL5428E 24-Port 10/100Mbp s + 4-Port Gigabit JetS t ream L2 Managed Switch Rev: 1.2.0 1910010529.
I COPYRIGHT & TRADEMARKS S pecifications ar e subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., L TD. Other brands and product names are trademarks or registered trademarks of t heir respective holders.
II CONTENTS Package C ontent s ............................................................................................................... ........... 1 Chapter 1 About this G uide...................................................................
III 5.1.2 Port Mi rror ........................................................................................................ 31 5.1.3 Port Security ....................................................................................................
IV 6.10 Application Example for Privat e VLAN ........................................................................ 82 Chapter 7 S panning T ree .......................................................................................................
V 9.3 V oice VLAN .............................................................................................................. 134 9.3.1 Global C onfi g ................................................................................................
VI 1 1.4.2 DoS Detect .................................................................................................... 175 11 . 5 802.1X ..............................................................................................................
VII 14.2.1 Log T abl e ....................................................................................................... 224 14.2.2 Local Log .......................................................................................................
1 Package Content s The following items should be found in your box: ¾ One TL-SL5428E Switch ¾ One power cord ¾ One console cable ¾ Two mounting brackets and other fittings ¾ Quick Installation G.
2 Chapter 1 About this Guide This User Guide contains information for se tup and management of TL-SL5428E switch. Please read this guide carefully before operation. 1.1 Intended Readers This Guide is intended for network managers fam iliar with IT concepts and network terminologies.
3 Chapter Introduction Chapter 4 System This module is used to c onfigure system properties of the switch. Here mainly introduces: z System Info: Configure the description, system time and network parameters of the switch.
4 Chapter Introduction Chapter 8 Multicast This module is used to co nfigure multicast func tion of the switch. Here mainly introduces: z IGMP Snooping: Configure global parameters of IGMP Snooping function, port propertie s, VLAN and multicast VLAN. z Multicast IP: Configure multicast IP t able.
5 Chapter Introduction Chapter 12 SNMP This module is used to configure SNMP function to provide a management frame to monitor and maintain the network devices.
6 Chapter 2 Introduction Thanks for choosing the TL-SL5428E 24-Port 10/ 100Mbps + 4-Port Gigabit L2 Manag ed Switch! 2.1 Overview of the Switch Designed for workgroups and department s, TL-S L5428E from TP-LINK provides wire-speed performance and full set of layer 2 management featur es.
7 + Supports T elnet, CLI, SNMP v1/v 2c/v3, RMON and web access. + Port Mirroring enables monitoring selected ingress/egress traffic. 2.3 Appearance Description 2.
8 2.3.2 Rear Panel The rear panel of TL-SL5428E features a power socket and a Gr ounding T erminal (marked with ). Figure 2-2 Rear Panel ¾ Grounding T erminal: TL-SL5428E already comes with Lightning Protection Mechanism. Y ou can also ground the Switch through the PE (Protecti ng Earth) cable of AC cord or with Ground Cable.
9 Chapter 3 Login to the Switch 3.1 Login 1) T o access the configurat ion utility , open a web-browser and type in the default address http://192.168.
10 Figure 3-3 Main Setup-Menu Note: Clicking Apply can only make the new conf igurati ons effective before the switch is rebooted. If you want to keep the configur ations effective even the switch is rebooted, please click Saving Config .
11 Chapter 4 System The System module is mainly for system confi guration of the switch, including four submenus: System Info , User Manage, System T ools and Access Security . 4.1 System Info The System Info, mainly for basic proper ties configuration, can be implemented on System Summary , Device Description , Sy stem T ime and Sy stem IP pages.
12 Indicates the 1000Mbps port is not connected to a device. Indicates the 1000Mbps port is at the speed of 1000Mbp s. Indicates the 1000Mbps port is at the speed of 10Mbp s or 100Mbps. Indicates the SFP port is not connected to a device. Indicates the SFP port is at the speed of 1000Mbps.
13 Figure 4-3 Bandwid th Utilization ¾ Bandwidth Utilization Rx: Select Rx to display the bandwidth utilization of receiving p ackets on this port. Tx: Select Tx to display the bandwi dth utilization of sending p ackets on this port.
14 Device Location: Enter the location of the switch. System Cont act: Enter your contact information. 4.1.3 System Ti me System T ime is the time displayed while th e switch is running. O n this page you can configure the system time and the s ettings here will be used for other time-based functions l ike ACL.
15 Get GMT : When this option is selected, y ou can configure the time zone and the IP Address for the NTP Se rver . The switch will get GMT automatically if it has connected to a NTP Server . z T ime Zone: Select your local time. z Primary/Secondary NTP Server: Enter the IP Address for the NTP Server .
16 IP Address Mode: Select the mode to obtain IP Address for the switch. z S tatic IP: When this option is selected, you should enter IP Address, Subnet Mask and Default Gateway manually . z DHCP: When this option is selected, the switch will obtain network parameters from the DHCP Server .
17 Figure 4-7 User T able 4.2.2 User Config On this page you can configure the access level of the user to log on to the Web management page. The switch provides two access levels : Guest and Admin. The guest only can view the settings without the right to conf igure the switch; the admin can c onfigure all the functions of the s w i t c h .
18 Password: T ype a password for users’ login. Confirm Password: Retype the password. ¾ User T able Select: Select the desired entry to delete the corresponding user information. It is multi-optional T he current user information can’t be deleted.
19 Note: 1. It will take a few minutes to restore the c onfiguration. Please wait without any operation. 2. T o avoid any damage, please don’t power down the switch while being restored. 3. After being restored, the current settings of the switch will be lost.
20 Figure 4-1 1 Firmware Upgrade Note: 1. Don’t interrupt the upgrade. 2. Please select the proper software version matching with your hardware to upgrade. 3. T o avoid damage, please don't turn off the device while upgrading. 4. After upgrading, the devic e will reboot automatically .
21 Figure 4-13 System Reset Note: After the system is reset, the sw itch will be reset to the default an d all the settings will be cleared. 4.4 Access Security Access Security provides different security m easures for the remote l ogin so as to enhance the configuration management secu rity.
22 Figure 4-14 Access Control The following entries are displayed on this screen: ¾ Access Control Config Control Mode: Select the control mode for users to log on to the W eb management page. z IP-based: Select this option to lim it the IP-range of the users for login.
23 Session Timeout: If you do nothing with the Web management page within the timeout time, the system will log out automatically . If you want to reconfigure, pl ease login again. ¾ Access User Number Number Control ； Select Enable/Disable the Number Control function.
24 Figure 4-15 SSL Config The following entries are displayed on this screen: ¾ Global Config SSL: Select Enable/Disable the SSL function on the switch. ¾ Certificate Download Certificate File: Select the desired certificate to download to the switch.
25 an insecure network environment. It can encry pt all the transmission data and prevent the information in a remote management being leaked. Comprising server and client, SSH has two versi ons, V1 and V2 which are not compatible with each other .
26 ¾ Key Download Key T ype: Select the type of SSH Key to download. The switch supports three types: SSH-1 RSA, SSH-2 RSA and SSH-2 DSA. Key File: Select the desired key file to download. Download: Click the Download button to down the desired key file to the switch.
27 Application Example 2 for SSH: ¾ Network Requirements 1. Log on to the switch via password authentic ation using SSH and the SSH function is enabled on the switch. 2. PuTTY client sof tware is recommended. ¾ Configuration Procedure 1. Select the key type and key length, and generate SSH key .
28 3. On the Web management page of the switch, download the public key file saved in the computer to the switch. Note: 1. The key typ e should accord wit h the type of the key file. 2. The SSH key dow nloading can not be i nterrupted. 4. Download the private key f ile to SSH client software.
29 5. After the public key and private key are downl oaded, please log on to the int erface of PuTTY and enter the IP address for login. After successful authentication, pl ease enter the login user name. If you log on to the switch without entering password, it indicates t hat the key has been successfully downloaded.
30 Chapter 5 Switching Switching module is used to conf igure the basic functi ons of the switch, in cluding four submenus: Port , LAG , T raffic Monitor and MAC Address . 5.1 Port The Port function, allowing you to configure the basic features fo r the port, is implemented on the Port Config , Port Mirror , Port Security and Port Isolation p ages.
31 Description: Give a description to the port for identification. Statu s: Allows you to Enable/Dis able the port. When Enable is selected, the port can forward the packet s normally . Speed and Duplex: Select the S peed and Duplex mode for the port.
32 Figure 5-2 Mirroring Port The following ent ries are displ ayed on this screen. ¾ Mirroring Port Mirroring Port: Select a port from the pull-down list as the mirroring port.
33 Note: 1. The LAG member can not be selected as the mirrored port or mirroring port. 2. A port can not be set as the mirrored port and the mirroring por t simultaneously .
34 Select: Select the desired port for Port Security configuration. It is multi-optional. Port: Displays the port number . Max Learned MAC: S pecify the maximum number of MAC addresses that can be learned on the port. Learned Num: Displays the number of MAC addr esses that have been learned on the port.
35 Figure 5-4 Port Isolation Config The following ent ries are displ ayed on this screen: ¾ Port Isolation Config Port: Select the port number to set its forwardlist. Forward Portlist: Select the port that to be forwarded to. ¾ Port Isolation List Port: Display the port number .
36 5.2 LAG LAG (Link Aggregation Group) is to combine a number of ports together to make a single high-bandwidth data path, so as to implement the traffic load sharing among the member ports in the group and to enhance the connection reliability . For the member ports in an aggregation group, t heir basic configuration must be the same.
37 Figure 5-5 LAG T able The following ent ries are displ ayed on this screen: ¾ Global Config Aggregate Arithmetic: Select the applied scope of Aggregate Arithmetic, which results in choosing a port to transfer the p ackets.
38 Figure 5-6 Det ail Information 5.2.2 St atic LAG On this page, you can manually c onfigure the LAG . The LACP feat ure is disabled for the member ports of the manually added S tatic LAG . Choose the menu Sw it chin g → LAG → St atic LAG to load the following page.
39 Description: Give a description to the LAG for identification. ¾ LAG T able Member Port: Select the p ort as the LAG member . Clearing all the ports o f the LAG will delete this LAG . Tips: 1. The LAG can be deleted by clearing its all member ports.
40 Figure 5-8 LACP Config The following ent ries are displ ayed on this screen: ¾ Global Config LACP: Enable/Disable the LA CP feature here. ¾ LACP Config Port Select: Click the Select button to quick-select the corresponding port based on the port number you entered.
41 member . The port with smaller Port Priority will be considered as the preferred one. If the two port pr iorities are equal; the port with smaller port number is preferred. Statu s: Enable/Disable the LACP feat ure for your selected port. LAG: Displays the LAG number which the port belongs to.
42 Refresh Rate: Enter a value in seconds to specify the refresh interval. ¾ T raffic Summary Port Select: Click the Sele ct button to quick-select the corresponding port based on the port number you entered. Port: Displays the port number . Packets Rx: Displays the number of packet s received on the port.
43 Auto Refresh: Allows you to Enable/Disable refreshing the Traf fic Summary automatically . Refresh Rate: Enter a value in seconds to specify the refresh interval. ¾ St atistics Port: Enter a port number and click the Select button to view the traffic statistics of the corresponding port.
44 updated by auto-learning. In the stable networks, th e static MAC address entries can facilitate the switch to reduce broadcast packets and enhance the efficiency of packets forwarding remarkably. The address filtering feature allo ws the switch to filter the undesired packets and forbid its forwarding so as to improve the network security.
45 Figure 5-1 1 Address T able The following ent ries are displ ayed on this screen: ¾ Search Option MAC Address: Enter the MAC address of your desired entry . VLAN ID: Enter the VLAN ID of your desired entry . Port: Select the corresponding port number of your desired entry .
46 MAC Address: Displays the MAC address learned by the switch. VLAN ID: Displays the correspondi ng VLAN ID of the MAC address. Port: Displays the corresponding Port number of the MAC address. Ty p e : Displays the T ype of the MAC addres s. Aging St atus: Displays the Aging status of the MAC address.
47 Search Option: Select a Search Option from the pull-down list and click the Search button to find your desired entry in the S tatic Address T able. • MAC: Enter the MAC address of your desired entry . • VLAN ID: Enter the VLAN ID number of your desired entry .
48 Figure 5-13 Dynamic Address The following ent ries are displ ayed on this screen: ¾ Aging Config Auto Aging: Allows you to Enable/Disable t he Auto Aging feature.
49 Select: Select the entry to delete the dy namic address or to bind the MAC address to the corresponding port statically . It is multi-optional. MAC Address: Displays the dynamic MAC Address. VLAN ID: Displays the correspondi ng VLAN ID of the MAC address.
50 The following ent ries are displ ayed on this screen: ¾ Create Filtering Address MAC Address: Enter the MAC Address to be filtered. VLAN ID: Enter the corresponding VLAN ID of the MAC address.
51 Chapter 6 VLAN The traditional Ethernet is a data network comm unication technology basi ng on CSMA/CD (Ca rrier Sense Multiple Access/Collision Detect) vi a shared communication medium.
52 different VLANs. The switch can analyze the received untagged p ackets on the port and match the packet s with the MAC VLAN, Protocol VLAN and 802. 1Q VLAN in turn. If a p acket is matched, the switch will add a corresponding VLAN tag to it and forward it in the corresponding VLAN.
53 （ 2 ） TRUNK: The TRUNK port can be added in multiple VL ANs, and the egress rule of the port is T AG . The TRUNK port is generally used to connect the cascaded network devices for it can receive and forward the packets of multiple VLANs. When the p ackets are forwarded by the TRUNK port, it s VLAN tag will n ot be changed.
54 Figure 6-3 VLAN T able T o ensure the normal communication of the factory sw itch, the default VLAN of all ports is set to VLAN1. The Web Management Page of switch can only be accessed through the ports in VLAN1. VLAN1 can not be modified or deleted.
55 Figure 6-4 Create or Modify 802.1Q VLAN The following ent ries are displ ayed on this screen: ¾ VLAN Config VLAN ID: Enter the ID number of VLAN. Description: Give a description to the VLAN for identification. Check: Click the Check button to check whether the VLAN ID you entered is valid or not.
56 Egress Rule: Select the Egress Rule for the VLAN port member . The defa ult egress rule is UNT AG . • T AG: All packe ts forwarded by the port are tagged. The packet s contain VLAN information. • UNT AG: Packets forwarded by the port LAG: Displays the LAG to which the port belongs.
57 Link T ype: Select the Link T ype from t he pull-down list for the port. • ACCESS: The ACCESS port c an be added in a single VLAN, and the egress rule of the port is UNT AG . The PVID is same as the current VLAN ID. If t he current VLAN is deleted, the PVID will be set to 1 by default.
58 the description for the VLAN. Meanwhile, specify its member ports. 3 Modify/View VLAN. Optional. On the VLAN → 802.1Q VLAN → VLAN Config pa ge, click the Edit/Det ail button to modify/view the information of the corresponding VLAN. 4 Delete VLAN Optional.
59 ¾ VLAN T able MAC Address: Enter the MAC address. Description: Give a description to the MA C addres s for identification. VLAN ID: Enter the ID number of the MAC VLAN.
60 the description for the VLAN. Meanwhile, specify its member ports. 3 Create MAC VLAN. Required. On the VLAN → MAC VLAN page, create the MAC VLAN. For the device in a MAC VLAN, it’s required to set it s connected port of switch to be a me mber of this VLAN so as to ensure the normal communication.
61 6.3.1 Protocol VLAN On this page, you can create Protocol VLAN and view the information of the current defined Protocol VLANs. Choose the menu VLAN → Protocol VLAN → Protocol VLAN to load the following page.
62 Figure 6-10 Create and View Protocol T emplate The following ent ries are displ ayed on this screen: ¾ Create Protocol T emplate Protocol Name: Give a name for the Protocol T emplate. Ether T ype: Enter the Ethernet protocol type field in the protocol template.
63 Configuration Procedure: Ste p Operation Description 1 Set the link type for port. Required. On the VLAN → 802.1Q VLAN → Port Config page, set the link type fo r the port basing on its connected device. 2 Create VLA N. Required. On the VLAN → 802.
64 ¾ Configuration Procedure z Configure Switch A Ste p Operation Description 1 Configure the Link T ype of the ports Required. On VLAN → 802.1Q VLAN → Port Config page, configure the link type of Port 2, Port 3 and Port 4 as ACCESS, TRUNK and ACCESS respectively 2 Create VLAN10 Required.
65 z Notebook A and Notebook B, spec ial for meeting r oom, are of two different department s; z The two departments are in VLAN10 and VLAN20 respectively .
66 z Configure Switch B Ste p Operation Description 1 Configure the Link T ype of the ports Required. On VLAN → 802.1Q VLAN → Port Config page, configure the link type of Port 21 and Port 22 as GENERAL and TRUNK respectively . 2 Create VLAN10 Required.
67 ¾ Configuration Procedure z Configure Switch A Ste p Operation Description 1 Configure the Link T ype of the ports Required. On VLAN → 802.1Q VLAN → Port Config page, configure the link type of Port 1 1 and Port 13 as ACCESS, and configure the link type of Port 12 as GENERAL.
68 5 Port Enable Required. On the VLAN → Protocol VLAN → Port Enable page, select and enable Port 3, Port 4 and Port 5 for Protocol VLAN feature. 6 Create Protocol VLAN 10 On VLAN → Protocol VLAN → Protocol VLAN page, create protocol VLAN 10 with Protocol as IP .
69 This VLAN VPN function is implemented on the VPN Config , VLAN Mapping and Port Enable pages. 6.7.1 VPN Config This page allows you to enable the VPN function, adjust the global TPID for VLAN-VPN packets and enable the VPN up-link port.
70 Figure 6-13 Create VLAN Mapping Entry The following ent ries are displ ayed on this screen: ¾ VLAN Mapping Config C VLAN: Enter the ID number of the Custom er VLAN. C VLAN refers to the VLAN to which the packet received by switch belongs. SP VLAN: Enter the ID number of the Service Provider VLAN.
71 Figure 6-14 Enable VLAN Mapping for Port Select your desired port for VLAN Mapping function. All the ports are disabled for VLAN Mapping function by default.
72 3 Create SP (Service Provider) VLAN Optional. On the VLAN → 802.1Q VLAN page, create the SP VLAN. For the step s of creating VLAN, please refer to 802.1Q VLAN . 6.8 GVRP GVRP (GARP VLAN Registration Protocol) is an implementation of GA RP (generic attribute registration protocol).
73 • LeaveAll Timer: Once a GARP entity starts up, it st arts the LeaveAll time r, and sends out a LeaveALL message after the timer times out, so t hat other GARP entitie s can re-register all the attribute information on this entity. After that, the entity re starts the LeaveAll timer to begin a new cycle.
74 Figure 6-15 GVRP Config Note: If the GVRP feature is enabled for a member port of LAG , please ensure all the member ports of this LAG are set to be in the same status and registration mode. The following ent ries are displ ayed on this screen: ¾ Global Config GVRP: Allows you to Enable/Disabl e the GVRP function.
75 • Fixed: In this mode, a port cannot register/deregister a VLAN dynamically . It only propagates static VLAN information. • Forbidden: In this mode, a port cannot register/deregister VLANs.
76 devices need to identify Primary VLANs but not Secondary VLANs. Therefore, they can save VLAN resources without consider ing the VLAN configuration in the lower layer . Meanwh ile, the service provider can assign each user an individual Secondary VLAN, so that users are separated at the Layer 2 level.
77 ports is untag by default, that is, only thos e untagged p ackets can be forwarded, but you can modify the egress rule on VLAN → 802.1Q VLAN → VLAN Config page. 2) Port configuration and MAC addr ess duplication should be sync hronized on the Switch.
78 z MAC address duplication: After port configuration synchronizat ion, packets from Secondary VLAN can be forwarded via the p romiscuous port untagged, and those from Primary VLAN can be sent via the host port untagged.
79 The Private VLAN packet forwarding process (here we take traffic transmission for PC2) based on the figure above is illu strated as follows: 1) PC2 sends out it s first up stream pa cke t with the source MAC as mac_2 and the destination MAC as mac_a.
80 Figure 6-17 Create Private VLAN The following ent ries are displ ayed on this screen: ¾ Create Private VLAN Primary VLAN: Enter the ID number of the Primary VLAN.
81 Choose the menu VLAN → Private VLAN → Port Config to load the following page. Figure 6-18 Create and View Protocol T emplate The following ent ries are displ ayed on this screen: ¾ Port Config Port: Select the desired port fo r configuration. Port T ype: Select the Port T ype from the pull-down list for the port.
82 4 Delete VLAN. Optional. On the VLAN → Private VLAN → PVLAN page, select the desired entry to delete the correspondi ng VLAN by clicking the Delete button.
83 button. 2 Add Promiscuous port to Private VLANs Required. On the VLAN → Private VLAN → Port Configure page, configure the port type of Port3 and Port4 as Promiscuous , enter Primary VLAN 6 and Secondary VLAN 2-3, and click the Add button. 3 Add Host port to Private VLANs Required.
84 Chapter 7 S p anning T r ee STP (S panning T r ee Protocol), su bject to IEEE 802.1 D standard, is to disbra nch a ring network in the Data Link layer in a local netwo rk.
85 z Port: Port 3 is the root port of switch B and port 5 is the root port of switch C; port 1 is the designated port of switch A and por t 4 is the designated port of swit ch B; port 6 is the blocked port of switch C. Figure 7-1 Basic STP diagram ¾ STP T imers Hello T ime: Hello T ime ranges from 1 to 10 seconds.
86 ¾ STP Generation z In the beginning In the beginning, each switch regards itself as the root, and generates a configuration BPDU for each port on it as a root, with the root path cost being 0, the ID of the designated bridge being that of the switch, and the designated port being itself.
87 Tips ： In a STP with stable top ology , only the root port and designated port can forwa rd data, and the other ports are blocked. The blo cked ports only can receive BPDUs. RSTP (R apid S p ann ing T ree P ro toco l), evo lve d fr om the 802 .1D STP stan dard, enable Ethernet ports to transit their states rapidl y .
88 Figure 7-2 Basic MSTP diagram ¾ MSTP MSTP divides a network into several MST r egions. The CST is generat ed between these MST regions, and multiple spanning trees can be generated in each MST region. Each spanning tress is called an instance. As well as STP , MSTP uses BPDUs to generate spanning tree.
89 Figure 7-3 Port roles The S panning T ree module is mainly for spanning tree configuration of the switch, including four submenus: STP Config , Port Config , MSTP Instance and STP Security . 7.1 STP Config The STP Config function, for global configuration of spanning trees on the switch, can be implemented on STP Config and STP Summary pages.
90 Figure 7-4 STP Config The following entries are displayed on this screen: ¾ Global Config STP: Select Enable/Disable STP f unction globally on the switch. V ersion: Select the desired STP version on the switch. z STP: S panning Tree Protocol. z RSTP: Rapid S panning T ree Protocol.
91 that occur in a specific region before the BPDU is discarded. The default value is 20 hops. Note: 1. The forward delay parameter and the network dia meter are correlated. A too small forwar d delay parameter may result in temporary loops. A too large forward delay may cau se a network unable to resume the normal state in time.
92 Figure 7-5 STP Summary 7.2 Port Config On this page you can c onfigure the parameters of t he ports for CIST Choose the menu Sp anning T ree → Port Config to load the following page.
93 Figure 7-6 Port Config The following entries are displayed on this screen: ¾ Port Config Port Select: Click the Select button to quick-select the corresponding port bas ed on the port number you entered. Select: Select the desired port for STP conf iguration.
94 Port Role: Displays the role of the port played in the STP Insta nce. z Root Port: Indicates the port that has the lowest p ath cost from this bridge to the Root Bridge and forwards packets to the root. z Designated Port: Indicates the port that forwards packet s to a downstream network segment or switch.
95 Figure 7-7 Region Config The following entries are displayed on this screen: ¾ Region Config Region Name: Create a name for MST region identif ication using up to 32 characters. Revision: Enter the revision from 0 to 6553 5 for MST region identification.
96 The following entries are displayed on this screen: ¾ Inst ance T able Inst ance ID Select: Click the Select button to quick-se lect the corresponding Instance ID based on the ID number you entered. Select: Select the desired Instance ID for c onfiguration.
97 Figure 7-9 Instance Port Config The following entries are displayed on this screen: ¾ Port Config Inst ance ID: Select the desired instance ID for its po rt configuration. Port Select: Click the Select button to quick-select the corresponding port bas ed on the port number you entered.
98 Note: The port status of one port in dif ferent spanning tree instances can be dif ferent. Global configuration Procedure for S panning T ree function: Ste p Operation Description 1 Make clear roles the switches play in spanning tree instances: root bridge or designated bridge Preparation.
99 A CIST and its secondary root bridges are usually located in the high-bandwidth core region. Wrong configuration or malicious attacks may resu lt in configuration BPD U p ackets with higher priorities being received by the legal root bridge, which causes the cu rrent legal root bridge to lose its position and network topology jitter to occur .
100 Figure 7-10 Port Protect The following entries are displayed on this screen: ¾ Port Protect Port Select: Click the Select button to quick-select the corresponding port bas ed on the port number you entered. Select: Select the desired port for port protect configuration.
101 7.4.2 TC Protect When TC Protect is enabled for the port on Port Protect page, the TC threshold and TC protect cycle need to be configured on this page.
102 7.5 Application Example for STP Function ¾ Network Requirements z Switch A, B, C, D and E all support MSTP function. z A is the central switch. z B and C are switches in the convergence layer . D, E and F are switches in the access layer . z There are 6 VLANs labeled as VLAN101-VLAN106 in the network.
103 z Configure Switch B: Ste p Operation Description 1 Configure ports On VLAN → 802.1Q VLAN page, configure the link type of the related ports as T runk, and add t he ports to VLAN 101 and VLAN 106. The detailed instructions can be found in the section 802.
104 z Configure Switch D: Ste p Operation Description 1 Configure ports On VLAN → 802.1Q VLAN page, configure the link type of the related ports as T runk, and add t he ports to VLAN 101 and VLAN 106. The detailed instructions can be found in the section 802.
105 ¾ Suggestion for Configuration z Enable TC Protect functio n for all the ports of switches. z Enable Root Protect function for a ll the ports of root bridges. z Enable Loop Protect function for the non-edge ports. Enable BPDU Protect function or BPDU Filter func tion for the edge ports which are connected to the PC and server .
106 Chapter 8 Multicast ¾ Multicast Overview In the network, packet s are sent in three modes: unicast, broadcas t and multicast. In unicast, the source server sends separate copy information to each receiver .
107 1. Multicast IP Address: As specified by IANA (Internet Assigned Numbe rs Authority), Class D IP addresses are used as destination addresses of multic ast packets. The multicast IP addresses range from 224.0.0.0~239.255.255.255. The following table displays the range and description of several special multicast IP addresses.
108 ¾ IGMP Snooping In the network, the hosts apply to the near Router for joining (leaving) a multicast group by sending IGMP (Internet Group Management Protocol) me ssages. When the up-str eam device forwards down the multicast data, the switch is responsible for sending them to the host s.
109 The host, running IGMPv1, does not send IGMP l eave message when leaving a multicast group, as a result, the switch can not get the leave information of the host momentarily .
11 0 Figure 8-4 Basic Config The following entries are displayed on this screen: ¾ Global Config IGMP Snooping: Select Enable/Disable IGMP S nooping function globally on the Switch. Unknown Multicast: Select the operation for the swit ch to process unknown multicast, Forward or Discard.
111 Figure 8-5 Port Config The following entries are displayed on this screen: ¾ Port Config Port Select: Click the Select button to quick-select the corresponding port based on the port number you entered. Select: Select the desired port for IGMP Snooping feature configuration.
11 2 Choose the menu Multicast → IGMP Snooping → VLAN Config to load the follo wing p age. Figure 8-6 VLAN Config The following entries are displayed on this screen: ¾ VLAN Config VLAN ID: Enter the VLAN ID to e nable IGMP Snooping for the desired VLAN.
11 3 Select: Select the desired VLAN ID for configuration. It is multi-optional. VLAN ID: Displays the VLAN ID. Router Port Time: Displays the router port time of the VL AN. Member Port T ime: Displays the member port time of the VLAN. Leave Time: Displays the leave time of the VLAN.
11 4 Figure 8-7 Multicast VLAN The following entries are displayed on this screen: ¾ Multicast VLAN Multicast VLAN: Select Enable/Disable Multicast VLAN feature. VLAN ID: Enter the VLAN ID of the multicas t VLAN. Router Port Time: S pecify the aging time o f the router port.
11 5 5. After a multicast VLAN is created, all the IGMP p ackets will be processed only within the multicast VLAN. Configuration procedure: Ste p Operation Description 1 Enable IGMP Snooping function Required. Enable IGMP Snooping globally on the switch and for the port on Multicast → IGMP Snooping → Snooping Config and Port Config p age .
11 6 ¾ Configuration Procedure Ste p Operation Description 1 Create VLANs Create three VLANs with the VLAN ID 3, 4 and 5 respectively , and specify the description of VL AN3 as Multicast VLAN on VLAN → 802.1Q VLAN page. 2 Configure ports On VLAN → 802.
11 7 8.3.1 Multicast IP T able On this page you can view the multicast IP table on the switch. Choose the menu Multicast → Multicast IP → Multicast IP T able to load the following page.
11 8 Choose the menu Multicast → Multicast IP → St atic Multicast IP to load the following page. Figure 8-9 S tatic Multicast IP T able The following entries are displayed on this screen: ¾ Create St ati c Multicast Multicast IP: Enter static multicast IP address.
11 9 8.4 Multicast Filter When IGMP Snooping is enabled, you can specified the multicast IP-range the ports can join so as to restrict users ordering multicast programs via configuring multicast filter rules. When applying for a multicast group, the host will send IGMP report message.
120 St art Multicast IP: Displays start multicas t IP of the IP-range. End Multicast IP: Displays end multicast IP of the IP-range. 8.4.2 Port Filter On this page you can configure t he multicast filter rules for port.
121 Action Mode: Select the action mode to process multicast pa ckets when the multicast IP is in the filtering IP-range. z Permit: Only the multicast packet s whose multicast IP is in the IP-range will be processed. z Deny: Only the multicast packets whose multicast IP is not in the IP-range will be processed.
122 Figure 8-12 Packet S tatistics The following entries are displayed on this screen: ¾ Auto Refresh Auto Refresh: Select Enable/Disable auto refresh feature. Refresh Period: Enter the time from 3 to 300 in seconds to specif y the auto refresh period.
123 Chapter 9 QoS QoS (Quality of Service) functi ons to provide different quality of service for various network applications and requirements and optim ize the bandwidth resource dist ribution so as to provide a network service experience of a better quality .
124 Figure 9-2 802.1Q frame As shown in the figure above, each 802.1Q T ag ha s a Pri field, comprising 3 bits. The 3-bit priority field is 802.1p priority in the range of 0 to 7. 802.1P priority determi nes the priority of the packets based on the Pri value.
125 Figure 9-4 SP-Mode 2. WRR-Mode: Weight Round Robin Mode. In this mode, pa ckets in all the queues are sent in order based on the weight value for each queue and every queue can be assured of a certain service time. The weight value indicates the occupied proportion of the resource.
126 The QoS module is mainly for traffic control and priority configuration, including three submenus: DiffServ , Bandwidth Control and V oice VLAN . 9.
127 Note: T o complete QoS function confi guration, you have to go to the Schedule Mode page to select a schedule mode after the configur ation is finishe d on this page. Configuration Procedure: Ste p Operation Description 1 Log on to the Port Priority page 2 Select the desired ports for configuration Select the desired ports.
128 SP+WRR-Mode: S trict-Priority + Weight Round R obin Mode. In this mode, this switch provides two scheduling groups, SP group and WRR group. Queues in SP group and WRR group are scheduled strictly based on strict-priority mode while the queu es inside WRR group follow the WRR mode.
129 Note: T o complete QoS function confi guration, you have to go to the Schedule Mode page to select a schedule mode after the configur ation is finishe d on this page. Configuration Procedure: Ste p Operation Description 1 Log on to the 8 02.1P Priority page 2 Enable 8 02.
130 Figure 9-9 DSCP Priority The following entries are displayed on this screen: ¾ DSCP Priority Config DSCP Priority: Select Enable or Disable DSCP Priority . ¾ Priority Level DSCP: Indicates the priority determined by the DS region of IP datagram.
131 3 Map the DSCP priority to the priority level Required. Select DSCP priority and the corresponding priority level. 4 Select a schedule mode Required.
132 Port: Displays the port number of the Switch. Ingress Rate (bps ): Configure the bandwidth for receiving packets on the port. Y ou can select a rate from the dropdown list or select "Manual&q.
133 Figure 9-1 1 S torm Control The following entries are displayed on this screen: ¾ Storm Control Config Port Select: Click the Select button to quick-select the corresponding port based on the port number you entered. Select: Select the desired port for S tor m Control conf iguration.
134 9.3 V oice VLAN V oice VLANs are configured spec ially for voice data stream. By configuring V oice VLANs and adding the ports with voice devices attached to voice VLANs, you can perform QoS-related configuration for voice data, ens uring the transmission priority of voice data stream and voice quality .
135 Port V oice VLAN Mode V oice Stream T ype Link type of the port and processing mode ACCESS: Not supported. TRUNK: Supported. The default VL AN of the port can not be voice VLAN. TA G v o i c e stream GENERAL: Supported. The defaul t VLAN of the port can not be voice VLAN and the egress rule of the access port in the voice VLAN should be T AG .
136 Note: Don’t transmit voice stream toget her with other business packet s in the voice VLAN except for some special requirements. The V oice VLAN functi on can be implemented on Global Config, Port Config and OUI Config pages.
137 Figure 9-13 Port Config Note: T o enable voice VLAN function for the LAG member port, please ensure its member state accords with its port mode. If a port is a member port of voice VLAN, changing .
138 Security Mode: Configur e the security mode for forwarding packets. z Disable: All packets are forwarded. z Enable: Only voice data are forwarded. Member St ate: Displays the st ate of the port in the current voice VLAN. LAG: Displays the LAG number which the port belongs to.
139 Configuration Procedure of V oice VLAN: Ste p Operation Description 1 Configure the link type of the port Required. On VLAN → 802.1Q VLAN → Port Config page, configure the link type of por ts of the voice device. 2 Create VLAN Requir ed. On VLAN → 802.
140 Chapter 10 ACL ACL (Access Control List) is used to filter packe ts by configuring match rules and process policie s of packet s in order to control the access of the illegal users to the network. Besides, ACL functions to control traffic flows and save network resource s.
141 10.1.2 T ime-Range Create On this page you can create time-ranges. Choose the menu ACL → Time-Range → Time-Range Create to load the following p age. Figure 10-2 T ime-Range Create Note: T o successfully configure time -ranges, please firstly specify ti me-slices and then time-ranges.
142 End Time: Displays the end time of the time-slice. Delete: Click the Delete button to delet e the corresponding time-slice. 10.1.3 Holiday Config Holiday mode is applied as a different secured a ccess control policy from the week mode. On this page you can define holidays according to your work arrangement.
143 The ACL C onfig functi on can be implemented on ACL Summary , ACL Create , MAC ACL , Stand ar d -I P AC L and Extend-IP ACL pages. 10.2.1 ACL Summary On this page, you can view the curr ent ACLs configured in the switch. Choose the menu ACL → ACL Config → ACL Summary to load the following page.
144 ACL ID: Enter ACL ID of the ACL y ou want to create. Rule Order: User Config order is set to be match order in this ACL. 10.2.3 MAC ACL MAC ACLs analyze and process packet s based on a se ries of match conditi ons, which can be the source MAC addresses, destination MAC addresse s, VLAN ID, and EtherT ype carried in the packet s .
145 User Priority: Select the user priority contained in the rule for the tagged p ackets to match. Time-Range: Select the time-range for t he rule to take ef fect.
146 10.2.5 Extend-IP ACL Extend-IP ACLs analyze and process data p acket s based on a series of ma tch conditions, which can be the source IP addresses, destination IP addre sses, IP protocol and other information of this sort carried in the packe ts.
147 Mask: Enter IP address mask. If it is set to 1, it must strictly match the address. IP Protocol: Select IP protocol contained in the rule. Select ICMP: Configure the predefined ICMP type and code. ICMP T ype: Configure the predefined ICMP type ICMP Code ： Configure the predefined ICMP code.
148 Select Policy: Select name of the desired policy fo r vi ew . If you want to delete the desired policy , please clic k the Delete button. ¾ Action T able Select: Select the desired entry to del ete the corresponding policy . Index: Enter the index of the policy .
149 Figure 10-1 1 Action Create The following entries are displayed on this screen: ¾ Create Action Select Policy: Select the name of the policy . Select ACL: Select the ACL for configuration in the policy . S-Mirror: Select S-Mir ror to mirror the data pa cket s in the policy to the specific port.
150 QoS Remark: Select QoS Remark to forward the data packet s based on the QoS settings. z DSCP: S pecify the DSCP region for the data p acket s those match the corresponding ACL. z Local Priority: S pecify the local priority for the data packet s those match the corresponding ACL.
151 Choose the menu ACL → Policy Binding → Port Binding to load the following p age. Figure 10-13 Bind the policy to the port The following entries are displayed on this screen: ¾ Port-Bind Config Policy Name: Select the name of the po licy you want to bind.
152 ¾ VLAN-Bind T able Index: Displays the index of the binding policy . Policy Name: Displays the name of the binding policy . VLAN ID: Displays the ID of the VL AN bound to the corresponding policy . Direction: Displays the binding direction. Configuration Procedure: Ste p Operation Description 1 Configure effective time-range Required.
153 ¾ Configuration Procedure Ste p Operation Description 1 Create VLANs On VLAN → 802.1Q VLAN page, create VLAN 6, specify it s description as RD, configure port 16 and port 2 as the members of VLAN 6. Connect RD department to port 16 of TL-SL5428E, and configure the link type of port 16 as GENERAL and its PVID as 6.
154 4 Configure for requirement 2 and 3 On ACL → ACL Config → ACL Create page, create ACL 100. On ACL → ACL Config → St andard-IP ACL page, select ACL 100 , create Rule 1, configure operatio n as Deny , configure S-IP as 172.31.70.1 and mask as 255.
155 Chapter 11 Network Security Network Security module is to provide the multip le protection measures fo r the network security , including five submenus: IP-MAC Binding , ARP Inspection , IP Source Guard, DoS Defend and 802.1X . Please configure t he functions appropriate to your need.
156 The following ent ries are displ ayed on this screen: ¾ Search Option Source: Select a Source from the pull-down list and click the Search button to view your desired entry in the Binding T able. • All: All the bound entries will be displayed. • Manual: Only the manually added entries will be displayed.
157 Figure 1 1-2 Manual Binding The following ent ries are displ ayed on this screen: ¾ Manual Binding Option Host Name: Enter the Host Name. IP Address: Enter the IP Address of the Host. MAC Address: Enter the MAC Address of the Host. VLAN ID: Enter the VLAN ID.
158 11.1.3 ARP Scanning ARP (Address Resolution Protocol) is u sed to analyze and map IP addresses to the corresponding MAC addresses so that p ackets can be delivered to their destinations correctly . IP address is the address of the Host on Network layer .
159 Figure 1 1-4 ARP Scanning The following ent ries are displ ayed on this screen: ¾ Scanning Option St art IP Address: S pecify the S tart IP Address. End IP Address: S pecify the End IP Address. VLAN ID: Enter the VLAN ID. If blank, the switch will send the unt agged packet s for scanning.
160 network configuration pr o tocol optimized and developed basing on the BOOTP , functions to solve the above mentioned problems. ¾ DHCP W orking Principle DHCP works via the “Client/Server” communication mode. The Client applies to the Server for configuration.
161 Figure 1 1-6 Interaction between a DHCP client and a DHCP server （ 1 ） DHCP-DISCOVER Stage: The Client broadcasts the DHCP-DISCOVER packet to find the DHCP Server .
162 Option 82 can contain 255 sub-options at most. If Option 82 is defined, at least a sub-option should be defined. This Switch s upports two sub-options: Circuit ID and Remote ID. Since there is no universal standard about the content of Op tion 82, different manufacturers define the sub-options of Option 82 to their need.
163 Cheating Attack by discarding the DHCP p ackets on the distrusted port, so as to enhance the network security . Choose the menu Network Security → IP-MAC Binding → Binding T able to load the following page.
164 ¾ DHCP Snooping Config DHCP Snooping: Enable/Disable the DHCP Snooping function globally . Global Flow Control: Select the value to specif y the maximum amount of DHCP messages that can be forwarded by the switch per second. The excessive massages will be discarded.
165 LAG: Displays the LAG to which the port belongs to. 11.2 ARP Inspection According to the ARP Implement ation Procedure stated in 1 1.1.3 ARP Scanning , it can be found that ARP protocol can facilit ate the Hosts in t he same network segment to communicate with one another or access to external network via Gatewa y .
166 Figure 1 1-10 ARP Attack – Cheating Gateway As the above figure shown, the at tacker sends the fake ARP p ackets of H ost A to the Gateway , and then the Gateway will automatically update its ARP table after receiving the ARP packet s.
167 Figure 1 1-1 1 ARP Attack – Cheating T erminal Hosts As the above figure shown, the atta cker sends the fake ARP p acket s of Host A to Host B, and then Host B will automatically update its ARP table afte r receiving the ARP p ackets.
168 Figure 1 1-12 Man-In-The-Middle Attack Suppose there are three Hosts in LAN connec ted with one another through a switch. Host A: IP ad dress is 192.168.0.101; MAC address is 00-00-00-1 1-1 1-1 1. Host B: IP address is 19 2.168.0. 102; MAC address is 00-00-00-22-22-2 2.
169 The IP-MAC Binding function allows the switch to bind the IP address, MAC address, VLAN ID and the connected Port number of the Host together when the Ho st connects to the switch.
170 Configuration Procedure: Ste p Operation Description 1 Bind the IP address, MAC address, VLAN ID and the connected Port number of the Host together . Required. On the IP-MAC Binding page, bind the IP address, MAC address, VLAN ID and the connected Port number of the Host together via Manual Binding, ARP Scanning or DHCP Snooping.
171 The following ent ries are displ ayed on this screen: ¾ ARP Defend Port Select: Click the Select button to quick-se lect the corresponding port based on the port number you entered. Select: Select your desired port for confi guration. It is multi-optional.
172 Figure 1 1-15 ARP S tatistics The following ent ries are displ ayed on this screen: ¾ Auto Refresh Auto Refresh: Enable/Disable the Auto Refresh feature. Refresh Interval: S pecify the refresh interval to display the ARP S tatistics. ¾ Illegal ARP Packet Port: Displays the port number .
173 Figure 1 1-16 IP Source Guard The following ent ries are displ ayed on this screen: ¾ IP Source Guard Config Port Select: Click the Select button to quick-selec t the corresponding port based on the port number you entered. Select: Select your desired port for confi guration.
174 With DoS Defend function enabled, the switch can anal yze the specific fields of the IP p ackets and distinguish the malicious DoS attack p ackets.
175 11.4.1 DoS Defend On this page, you can enable the DoS De fend type appropriate to your need. Choose the menu Network Securit y → DoS Defend → DoS Defend to load the following page. Figure 1 1-17 DoS Defend The following ent ries are displ ayed on this screen: ¾ Defend Config DoS Defend: Allows you to Enable/Dis able DoS Defend function.
176 Choose the menu Network Securit y → DoS Defend → DoS Detect to load the following page. Figure 1 1-18 DoS Detect The following ent ries are displ ayed on this screen: ¾ Detect Config Detect Time: S pecify the detect time for eac h DoS attack type except the flooding attack type.
177 Figure 1 1-19 Architecture of 802.1X authentication （ 1 ） Supplicant S ystem: The supplicant system is an entit y in LAN and is authenticated by the authenticator system. T he supplicant system is usually a common user terminal computer . An 802.
178 authentication by sending EAP-Reque st/Identity packet s to the supp licant. The supplicant system can also launch an 802.1X client program to initiate an 802.1X authentic ation through the sending of an EAPOL-S tart p acket to the switch, This TP-LINK switch can authentic ate supplicant systems in EAP relay mode or EAP terminating mode.
179 RADIUS Access-Challenge packet. The switch then sends the key to the 802.1X client program. 5. Upon receiving the key (encapsulated in an EAP-Request/MD5 Challenge packet) from the switch, the cli.
180 ¾ 802.1X Timer In 802.1 x authentication, the fo llowing timers are used to ensure that the supplicant system, the switch, and the RADIUS server interact in an orderly way: （ 1 ） Supplicant system timer (Supplicant Timeout): This timer is triggered by the switch after the switch sends a request packet to a supplicant system.
181 Figure 1 1-22 Global Config The following ent ries are displ ayed on this screen: ¾ Global Config 802.1X: Enable/Disa ble the 802.1X function. Authentication Method: Select the Authentication Me thod from the pull-down list. • EAP-MD5: IEEE 802.
182 failed to the 802.1X Authenticat ion, then the switch will not respond to the authentication requ est from the same supplicant during the Quiet Period.
183 Statu s: Select Enable/Disable the 802.1X authentication feature for the port. Guest VLAN: Select Enable/Disable the Gues t VLAN feature for the port. Control Mode: S pecify the Control Mode for the port. • Auto: In this mode, the port will normally work only after passing the 802.
184 Primary IP: Enter the IP address of the authentication server . Secondary IP: Enter the IP address of the al ternate authentication server . Authentication Port: Set the UDP port of authentication server(s).
185 Chapter 12 SNMP ¾ SNMP Overvie w SNMP (Simple Network Management Protocol) has gained the most extens ive application on the UDP/IP networks. SNMP provides a managem ent frame to monitor and maintain the network devices. It is used for automatica lly managing the various network devices no matter the physical differences of the devices.
186 SNMP v1: SNMP v1 adopts Community Name authentic ation. The community name is used to define the relation between SNMP Management S tation and SNMP Agent. The SNMP packe ts failing to pass community name authentication are discarded. The community name can limit access to SNMP Agent from SNMP NMS, functioning as a p assword.
187 The User is configured in a SNMP Group can manage the switch via the client program on management station. The specif ied User Name and the Auth/Privacy Password are used for SNMP Management S tation to access the SNMP Agent, functioning as the pa ssword.
188 Note: The amount of Engine ID c haracters must be even. 12.1.2 SNMP V iew The OID (Object Identifier) of t he SNMP packets is used to describe the managed objects of the switch, and the MIB (Management Information Base) is the set of the OIDs. The SNMP View is created for the SNMP management station to manage MIB objects.
189 12.1.3 SNMP Group On this page, you can co nfigure SNMP Group to control the network access by providing the users in various groups with different management right s via the Read View , Write View and Notify View . Choose the menu SNMP → SNMP Config → SNMP Group to load the following page.
190 writing only and changes can be made to the a ssigned SNMP View . The View defined both as the Read View and the Write View can be read and modified. Notify V iew: Select the Vi ew to be the Notify View . The management station can receive notification messages of the assigned SNMP view generated by the Switch's SNMP agent.
191 Figure 12-6 SNMP User The following ent ries are displ ayed on this screen: ¾ User Config User Name: Enter the User Name here. User T ype: Select the type for the User . • Local User: Indicates that the user is connected to a local SNMP engine.
192 ¾ User T able Select: Select the desired entry to del ete the corresponding User . It is multi-optional. User Name: Displays the name of the User . User T ype: Displays the User T ype. Group Name: Displays the Group Name of the User . Security Model: Displays the Security Model of the User .
193 • read-only: Management right of the Community is restricted to read-only, and changes cannot be made to the corresponding View. • read-write: Management right of the Comm unity is read-write and changes can be made to the correspondin g View.
194 2 Create SNMP V iew . Required. On the SNMP → SNMP Config → SNMP View page, create SNMP V iew of the management agent. The default View Name is viewDefault and the default OID is 1. Create SNMP Community directly . 3 Configure access level for the User .
195 Figure 12-8 Notification Config The following ent ries are displ ayed on this screen: ¾ Create Notification IP Address: Enter the IP Address of the management Host. UDP Port: Enter the number of the UDP por t used to send notifications. The UDP port functions with the IP address for the notification sending.
196 Select: Select the desired entry to delete the corresponding management station. IP Address: Displays the IP Address of the management host. UDP Port: Displays the UDP port us ed to send notifications. User: Displays the User name of the management station.
197 The RMON Groups can be configured on the History Control, Event Config and Alarm Config pages. 12.3.1 History Control On this page, you can confi gure the History Group for RMON. Choose the menu SNMP → RMON → History Control to load the following page.
198 Figure 12-10 Event Config The following ent ries are displ ayed on this screen: ¾ Event T able Select: Select the desired entry for configuration. Index: Displays the index number of the entry . User: Enter the name of the User or the community to which the event belongs.
199 Figure 12-1 1 Alarm Config The following ent ries are displ ayed on this screen: ¾ Alarm T able Select: Select the desired entry for configuration. Index: Displays the index number of the entry . Va r i a b l e : Select the alarm variables from the pull-down list.
200 Interval: Enter the alarm interval time in seconds. Ow ne r: Enter the name of the device or user that defined the entry . Statu s: Select Enable/Disable t he corresponding alarm entry .
201 Chapter 13 Cluster With the development of network technology , the network scale is getting larger and more networ k devices are required, which may result in a mo re complicated network m anagement system.
202 z The commander switch discovers and determines candidate switches by collecting related information. z After being added to the cluster , the candidate switch becomes to be the member switch, z After being removed from the cluster , the mem ber switch becomes to be the candidate switch.
203 The following entries are displayed on this screen: ¾ Neighbor Search Option: Select the information the desir ed e ntry should contain and then click the Search button to display the desired entry in the following Neighbor Information table. ¾ Neighbor Info Native Port: Displays the port number of the switch.
204 Figure 13-3 NDP Summary The following entries are displayed on this screen: ¾ Global Config NDP: Displays the global NDP status (enabled or disabled) for the switch. Aging Time: Displays the period for the neighbor switch to keep the NDP packet s from this switch.
205 Det ail ： Click the Deta il button to view the complete information collected for the port. 13.1.3 NDP Config On this page you can configure the NDP function for the switch. Choose the menu Cluster → NDP → NDP Config to load the following page.
206 Port: Displays the port number of the switch. NDP: Displays NDP status of the current port. Enable: Click the Enable button to enable NDP for the port you select. Disable: Click the Disable button to disabl e NDP for the port you select. Note: 1. NDP function is ef fective only when NDP function is enabled globally and for the port.
207 ¾ Device T able Device T ype: Displays the device description collected through NTDP . Device MAC: Displays the MAC address of this device. Cluster Name: Displays the cluster nam e of this device. Role: Displays the role this device plays in the cluster .
208 Figure 13-7 NTDP Summary The following entries are displayed on this screen: ¾ Global Config NTDP: Displays the NTDP status (enabled or disabled) of the switch globally . NTDP Interval T ime: Displays the interval to co llect topology information.
209 Port: Displays the port number of the switch. NTDP: Displays NTDP status (e nabled or disabled) of the current port. 13.2.3 NTDP Config On this page you can configure NTDP globally . Choose the menu Cluster → NTDP → NT DP Config to load the following p age.
210 NTDP Hop Delay: Enter the time between the switch receiving NTDP request packet s and the switch forwarding NTDP request pa ckets for the first time. Th e default is 200 milliseconds. NTDP Port Delay : Enter the time between the port forwar ding NTDP request p ackets and its adjacent port forwarding NTDP request p ackets over .
21 1 ¾ Global Cluster: Displays the cluster status (enabl ed or disabled) of the switch. Cluster Role: Displays the role the switch plays in the cluster .
212 Device MAC: Displays the MAC address of the member switch. IP Address: Displays the IP address of the member switch used in the cluste r . Statu s: Displays the connection status of the member switch. Role: Displays the role the switch plays currently .
213 The following entries are displayed on this screen: ¾ Global Config Cluster: Displays the cluster status (enabl ed or disabled) of the switch. Cluster Role: Displays the role the switch plays in the cluster . 13.3.2 Cluster Config On this page you can configure the sta tus of the cluster the switch belongs to.
214 Figure 13-14 Cluster Configuration for Commander Switch The following entries are displayed on this screen: ¾ Current Role Role: Displays the role the current switch plays in the cluster . ¾ Role Change Candidate: Select this option to change the role of the switch to be can didate switch.
215 ¾ Current Role Role: Displays the role the current switch plays in the cluster . ¾ Role Change Individual: Select this o ption to change the role of the switch to be individual switch. z For an individual switch, the following page is displayed.
216 Figure 13-17 Member Config The following entries are displayed on this screen: ¾ Create Member Member MAC: Enter the MAC address of the candidate switch. ¾ Member Info Select: Select the desired entry to manage/delete the correspond ing member switch.
217 Figure 13-18 Collect T opology The following entries are displayed on this screen: ¾ Graphic Show Collect T opology: Click the Collect T opology button to display the cluster topology .
218 Ste p Operation Description 1 Enable the NDP function globally and for the port, and then configure NDP parameters Optional. On Cluster → NDP → NDP Config page, enable the NDP function on the switch. 2 Enable the NTDP function globally and for the port, and then configure NTDP parameters Optional.
219 z Port 1 of the commander switch is connecting to the external ne twork, port 2 is connecting to member switch 1 and port 3 is c onnecting to member switch 2.
220 4 Configure the member switch On Cluster → Cluster → Member Config page, select the member switch and click the Manage button to log on to its W eb management page.
221 Chapter 14 Maintenance Maintenance module, assembling the commonly used system tools to manage the switch, provides the convenient method to locate and solve the network problem. （ 1 ） System Monitor: Monitor the utilization stat us of the memory and the CPU of switch.
222 Figure 14-1 CPU Monitor Click the Monitor button to enable the switch to monitor and display its CPU utilization rate every four seconds. 14.1.2 Memory Monitor Choose the menu Maintenance → S ystem Monitor → Memory Monitor to load the following page.
223 Figure 14-2 Memory Monitor Click the Monitor button to enable the switch to monitor and display its Memory utilization rate every four seconds. 14.
224 The Log function is implemented on the Log T able , Local Log , Remote Log and Backup Log pages. 14.2.1 Log T abl e The switch supports logs output to two directions , namely , log buffer and log file.
225 14.2.2 Local Log Local Log is the log information saved in switch. By default, all system logs are saved in log buffer and the logs with severities from level_0 to level _4 are saved in log file meanwhile. On this page, you can set the output channel for logs.
226 Figure 14-5 Log Host The following ent ries are displ ayed on this screen: ¾ Log Host Index: Displays the index of the log host. The switch supports 4 log hosts. Host IP: Configure the IP for the log host. UDP Port: Displays the UDP port used for receiving/sending log information.
227 Figure 14-6 Backup Log The following ent ry is displayed on this screen: ¾ Backup Log Backup Log: Click the Backup Log button to save the log as a file to your computer . Note: It will take a few minutes to backup the l og file. Please wait without any operation.
228 Statu s: Displays the connection status of the cable connected to the port. The test results of the cable include normal, close, open or impedance. Length: If the connection status is normal, here displays the length range o f the cable. Error: If the connection status is close, open or impedanc e, here displays the error length of the cable.
229 T est: Click the T est button to st art the loopback test for the port. 14.4 Network Diagnose This switch provides Ping test and T rac ert test functions for network diagnose.
230 14.4.2 T racert T racert test function is used to test the connecti vity of the gateways during its journey from the source to destination of the test data. When ma lfunctions occur to the network, you can locate trouble spot of the network with this tracert test.
231 Chapter 15 System Maintenance via FTP The firmware can be downloaded to the switch via FTP function. FTP (File Transfer Protocol), a protocol in the applicati on layer, is mainly used to transfer files between the remote server and the local PCs. It is a common protocol used in the IP network for file s transfer.
232 Figure 15-2 Open Hyper T erminal 2 ） The Connection Description Wi ndow will prompt shown as Figure 15-3. Enter a name into the Name field and click OK . Figure 15-3 Conn ection Description 3 ） Select the port to connect in Figure 15-4 and click OK .
233 Figure 15-4 Select the port to connect 4 ） Configure the port selected in t he step above shown as the following Figure 15-5. Configure Bit s per second as 38400, Data bit s as 8, Parity as None, Sto p b i ts as 1, Flow control as None, and then click OK .
234 Figure 15-6 bootrom Menu As the prompt is displayed for a short time, you are suggested not to release the CTRL-B key until you enter into bootrom menu after powering on the switch. 3 ） After entering into bootrom menu, please firstly configure the IP p arameters of the switch.
235 7 ） Please enter st art command to start the swit ch shown as the following figure. Enter the user name and password (the default user name and password are both admin) to login to the CLI command window and you can m anage the switch via CLI command.
236 Appendix A: S pecifications IEEE802.3 10Base-T Ethernet IEEE802.3u 100Base-TX/100Bas e-FX Fast Ethernet IEEE802.3ab 1000Base-T Gigabit Ethernet IEEE802.3z 1000Base- X Gigabit Ethernet IEEE802.3x Flow Control IEEE802.1p Priority IEEE802.1q VLAN Bridge Standards IEEE802.
237 Appendix B: Configuring the PCs In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows 2000. First make sure your Ethernet Adapter is work ing, refer to the adapter ’s manual if necessary .
238 Figure B-2 5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default..
239 6) Select Use the following IP address . And the following items will be available. If the switch's IP address is 192.168.0.1, specify IP address as 192.168.0. x (x is from 2 to 254), and the Subnet mask as 255.255.255.0. Now: Click OK to save your settings.
240 Appendix C: 802.1X Client Sof tware In 802.1X mechanism, the supplicant Client s hould be equipped with the corresponding client software complied with 802.
241 Figure C-3 Welcome to the InstallShield Wizard 4. T o continue, choose the destination location for the installation files and click Next on the following screen. Figure C-4 Choose De stination Location By default, the installation files are saved on t he Program Files folder of system disk.
242 Figure C-5 Install the Program 6. The Inst allShield Wizard is installing TpSupplicant-V2.0 shown as the following screen. Please wait. Figure C-6 Setup S tatus 7.
243 Figure C-7 InstallShield Wizard Complete Note: Please pay attention to the ti ps on the above screen. If you have not installed WinPcap 4.0.2 or the higher version on your computer , the 802.1X Client Softw a re TpSupplicant can not work. It’s recommended to go to http://www .
244 Figure C-8 Preparing Setup 3. On the continued screen, click Ye s to remove the application from your PC. Figure C-9 Uninstall the Application 4. Click Finish to complete. Figure C-10 Uninstall Complete 1.3 Configuration 1. After completing inst allation, double click the icon to run the TP-LINK 802.
245 Figure C-1 1 TP-LINK 802.1X Client Enter the Name and the Passwo rd specified in the Authentic ation Server . The length of Name and Password should be less than 15 characters. 2. Click the Properties button on Figure C-1 1 to lo ad the following screen for configuring the connection prope rties.
246 Auto reconnect af ter timeout: Select this option to allow the Client to automatically start the connection again when it does not re ceive the handshake reply packet s from the switch within a period. 3. T o continue, click Connect button after entering the Name and Password on Figure C-1 1 .
247 FA Q : Q1: Why does this error dialog box pop up when star ting up the TP-LINK 802.1X Client Software? A1: It’s because the supported DLL file is missing. Y ou are suggested to go to http://www .winpcap.org to download WinPcap 4.0 .2 or the higher version for installation, and run the client software again.
248 Appendix D: Glossary Access Control List (ACL) ACLs can limit network traffic and restrict access to certain users or devices by checking each packet for certain IP or MAC (i.
249 GMRP allows network devices to register end stations with multic ast groups. GMRP requires that any participating network devic es or end stations comply with the IEEE 802.1p standard. Group Attribute Registration Protocol (GARP) See Generic Attribute Registration Protocol.
250 Data Link layer in the ISO 7-Layer Data Commun ica tions Protocol. This is related directly to the hardware interface for network devices and passes on traffic based on MAC addresses.
251 A secure replacement for remote access functi ons, including Telnet. SSH can authenticate users with a cryptographic key, and encrypt data c onne ctions between manage ment clients and the switch. Simple Network Management Protocol (SNMP) The application protocol in the Internet suit e of protocols which o ffers network management services.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté TP-Link tl-sl5428e c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du TP-Link tl-sl5428e - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation TP-Link tl-sl5428e, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le TP-Link tl-sl5428e va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le TP-Link tl-sl5428e, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du TP-Link tl-sl5428e.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le TP-Link tl-sl5428e. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei TP-Link tl-sl5428e ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
