Manuel d'utilisation / d'entretien du produit SD-W1111 du fabricant Toshiba
Aller à la page of 34
TOSHIBA DISK PRODUCTS DIVISION SD-W 1111 DVD-RAM DRIVE PRODUCT SPECIFICA TION JUNE 1999 REV . 1.0 Specifications are subject to change without notice DOCUMENT NUMBER 12043.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 2 Product Specification Matters to be attended to: This drive adopts RPC-II for its “ Standard Specification Model ” .
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 3 Product Specification Precaution This equipment ( an optical disc drive) handled under the conditions out of product specif.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 4 Product Specification 1. Scope ...............................................................................................................................................
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 5 Product Specification 15. MISCELLANEOUS ........................................................................................................................... 30 15.1 Accessories .
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 6 Product Specification 1. Scope The specification is applied to DVD-RAM drive SD-W1111. 2. Features (1) 2.6 GBytes capacity on one side of a 120 mm disc • Us ing 650 nm short-wavelength laser, 0.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 7 Product Specification 3. External views and dimensions External views: 146.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 8 Product Specification 4. Basic specifications • 5.25 ” half height form factor • Applicable discs(1G B = 2 30 Byte, 1M B = 2 20 Byte 1K B = 2 10 Byte) 1) DVD-RAM * 1 DVD Specification s for R ewritable Disc Part 1 Ve rsion 1.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 9 Product Specification • Average seek time ( Operating time of SEEK command ) DVD-RAM 120 ms ( typ.) DVD-ROM 210 ms ( typ.) CD-ROM 140 ms ( typ.) • Average access time DVD-RAM playback 180 ms * 1 ( typ.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 10 Product Specification 5. Power supply specifications 5.1 Input power supply +5V ± 5%, peak current 3A (Max. 2 sec., at spindle motor ON/OFF) Note: Power supply current is usually 1.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 11 Product Specification According to the steps described below, the optical head auto-lock mechanism can be functioned. • Eject a disc. • Pull-in the tray inside the drive.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 12 Product Specification 8.2 Relative humidity Operating 8 to 80% RH Storing 5 to 95% RH Transporting (with packing) 5 to 95% RH (Temperature variation gradient: 10% /h, absolute humidity: 30 gm 3 ) * No dew condensation 8.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 13 Product Specification EN61000-4-6 : 1996 EN61000-4-8 : 199 3 EN61000-4-11 : 1994.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 14 Product Specification 9. Block diagram ROM (2 Mbit ) CPU DVD-RAM/ROM p rocessor LD c ontroller Mode select jumper Audio ou.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 15 Product Specification 10. Mounting 10.1 Mounting Mount the drive using four M3 tapping holes bottom and two M3 tapping holes on each side. The following shows an example mounting on a personal computer or a sub system.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 16 Product Specification 10.2 Mounting direction Install direction Horizontal or vertical installation (When using a n 80mm disc, vertical direction installation is not allowed.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 17 Product Specification 10.3 Notes on mounting • Keep more than 5mm clearance to circulate an adequate amount of air by c onvection around the drive and mounting metal parts.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 18 Product Specification • Do not apply force (under 1.5N : 150gf ) caving in the top plate. • Use screws of which length inside the drive should be more than 2.5mm and less than 3.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 19 Product Specification 11. Front bezel 11.1 Standard Bezel The front view of the drive with a s tandard bezel • Load/Unlo.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 20 Product Specification (3) A disc is not loaded, all LED ’ s turn off. (4) While executing following command, “ BUSY ” LED turns on.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 21 Product Specification 12. Rear View and Connectors The rear view of the drive • Power supply connector (4 pin): DC power supply is to be connected. • I / F (SCSI) connector (50 pin) : SCSI connector is to be connected.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 22 Product Specification 12.2 I/F connector (SCSI connector) 12.2.1 Pin No. table of connector terminal Pin Signal Pin Signal.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 23 Product Specification 12.2.2 External view diagram 12.2.3 Signal interface Type 50 core flat cable or 25 couple stranded wire cable Inductor size more than AWG28 Characteristic impedance 100 ohm ± 10% Maximum cable length 3.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 24 Product Specification 12.3 Mode select header s functions By inserting the jumper wire to the mode select headers , each kind of operation mode is made. Mode select headers : 2.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 25 Product Specification 1 2 3 4 12.3.4 ONE LUN/TWO LUN setting Pin 6 Function Open The drive operates in ONE LUN mode . Short The drive operates in TWO LUN mode . ONE LUN mode : The drive operates in one LUN (Logical Unit Number) for all discs to which SFF8090 Ver.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 26 Product Specification 13. Host interface specification 13.1 Applicable standard SCSI Command set SFF8090 Ver. 2 Rev 0.95 ANSI X3T9.2 Rev 10 L 13.2 SCSI command set Code (Hex.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 27 Product Specification Code (Hex.) Command 5A MODE SEN S E (10) A2 SEND E VENT A3 SEND KEY A4 REPORT KEY A5 PL AY AUDIO (12.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 28 Product Specification 14. Notes on data guarantee 14.1 Disappearance of data in buffer in a write cache operation In a write cache operation, before data are actually written to a disc, a status response to the WRITE command or WRITE & VERIFY command is sent.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 29 Product Specification Moreover, not only the data which tried to be recorded but also the data of other addresses in the same ECC block might be lost due to the failure to record.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 30 Product Specification 15. MISCELLANEOUS 15.1 Accessories Function setting jumper pins 5 p ie ce s. Emergency eject tool 1 p iece . 15.2 A bare disc setting at vertical installation In case of using a bare disc (ex.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 31 Product Specification 3. First hang a disc on a disc holder in an upper and rear side of a tray , and then put the disc on disc holders in a down side of the tray. 4. Check three disc holders to confirm to the disc surely.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 32 Product Specification Notes in use (1) A disc might be scratched, damaged and dropped from a tray when used with a disc not correctly installed. Please install correctly and use a disc.
OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 33 Product Specification 15.3 Disc eject at emergency Please do according to the following procedures when it is necessary to take out a disc from the drive in the emergency. Check that the power supply of the drive is turned off and one minute or more passes.
Deviation List Page Item Rev # 0.9 a Rev # 1 . 0 3 Caution s --- Add (6) 8 Rotational speed(DVD-RAM) 1 ,130 - 2,640 rpm 1,028 – 2,400 rpm Host I/F ANSI ~ R ev 10k ANSI ~ Rev 10L 9 Average access time 150 ms ( typ.) 170 ms ( typ.) 12 8.3 vibration 9.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Toshiba SD-W1111 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Toshiba SD-W1111 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Toshiba SD-W1111, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Toshiba SD-W1111 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Toshiba SD-W1111, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Toshiba SD-W1111.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Toshiba SD-W1111. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Toshiba SD-W1111 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
