Manuel d'utilisation / d'entretien du produit CST38MH du fabricant TOA Electronics
Aller à la page of 24
D R A F T 0 5 - 2 3 - 0 6 ( 2 ) I N S T A L L A T I O N I N S T R U C T I O N S M A N U A L 36" W ood Burning Fireplaces P/N 70 0,0 33M , R EV . C , 12 /20 06 Model CST38MH Retain These Instructions For Future Reference Report No.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 2 1 . Before starting your fireplace installation, read these installation instructions carefully to be sure you understand them completely and in entirety . Failure to follow them could cause a fireplace malfunction resulting in serious injury and/or property damage.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 3 Figure 1 TYPICAL INST ALLA TION INTRODUCTION General Information The CST38MH Series is a radiant-heat, two- sided fireplace with standard glass doors and an outside combustion air kit is provided.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 4 Figure 2 ASSEMBL Y OUTLINE Before Y ou Start Check your inventory list to be sure you have all the necessar y parts supplied in good us- able condition. Check also for any concealed damage. Check the operation of the damper .
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 5 Figure 7 Figure 6 ASSEMBL Y STEPS Note: The following steps represent the normal sequence of installation. Each installation is unique, however , and might require a different sequence. 1. Position firebox prior to framing or into prepared framing.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 6 The safety strips should extend in front and sides of the fireplace opening 2" (51 mm) . In the event a wooden support is used to elevate .
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 7 Figure 13 7" Min. (178 mm) 23 ¹⁵⁄₁₆ " (608 mm) 42 ³⁄₄ " (1086 mm) 49" (1245 mm) 40 ¹⁄₄ " (1022 mm) 4.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 8 Figure 14 FRAMING WALL V ARIA TIONS As many as six (6) different framed wall con- figurations can be constructed to enclose the Fireplaces. The following illustrations depict these variations of wall enclosures.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 9 INST ALLING THE CHIMNEY SYSTEM Step 1. Chec k flue da m p e r for prope r opera tio n. T o open, push handle up and release. Damper will open automatically . T o close, pull handle down and release damper will fall to the closed posi- tion.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 10 For new construction, to determine chimney center line, use plumb line from roof or ceil- ing above fireplace to center of flue collar on fireplace.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 11 Step 5. The heigh t of ver tica l chimne y pip e sup- ported only by the fireplace must not exceed 30'. Chimney heights above 30' must be supported by a Model FTF8-S4 stabilizer installed at 30' intervals.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 12 Step 8. The standard Security Chimneys FTF8 roof flashing assemblies include a storm collar . Slide the storm collar over outer chimne y , rest on flashi ng spac ers and align with top sur face of flashing.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 13 Figure 33 TEN FOOT RULE SUMMARY The minimum chimney height above the roof and/or to adjacent walls and buildings is speci- fied by all major building codes.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 14 A B FTF8-ES30 Number of FTF8 A B Offset Height Offset/Return FTF8-S4 Chimney Sections Offset Height (Inches) (Inches) Elbow Set Stabilizer 12&q.
15 11 0 11 1 0 0 0 279 0.28 17 1 5 0 1 0 0 432 0.43 21 1 9 2 0 0 0 540 0.54 27 2 3 1 1 0 0 692 0.69 35 2 11 0 0 1 0 889 0.89 47 3 11 0 0 0 1 1194 1.19 51 4 3 0 1 1 0 1302 1.30 57 4 9 1 0 0 1 1454 1.45 63 5 3 0 1 0 1 1607 1.61 67 5 7 2 0 0 1 1708 1.71 73 6 1 1 1 0 1 1861 1.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 16 OFFSET ELBOW ASSEMBL Y Offset elbows install the same as chimney sections. First, snap the inner section INTO the preceding inner section of flue. Check con- nection by pulling up slightly to ensure a tight fit.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 17 CHIMNEY OFFSET 30° THROUGH FLOOR OR CEILING It may be necessar y to assemble the chimney at 30° when passing through the floor or ceil- ing area. Use the F8FS30-2 firestop spacer as shown in Figures 41 and 42.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 18 If you’re installing a gas line, connect it before the fireplace is framed and enclosed in the finished wall. The gas knockout is determined by a 1-1/8" (29 mm) round indentation located at the bottom and slightly off center in the side refractories.
19 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Figure 46 Hearth Extension Dimensions A 16" B 28-1/2" C 8" D 44-1/2" Methods of Determining Hearth Extension and Wall Shiel.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 20 ACCESSORY P ARTS AND COMPONENTS LIST FOR MODEL CST38MH The accessory parts and components shown on Pages 21 and 22 are to be used only with your CST -38MH fireplace system. Separate installa- tion instructions are packaged with all combus- tion air kits and chimney terminations.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 21 INST ALLA TION COMPONENTS 63L10 FTF8-12 63L13 FTF8-18 H0522 FTF8-24 63L14 FTF8-36 Chimney Section 63L15 FTF8-48 Offset/ Return Package 30 Degre.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 22 “All-Glass TM ” 38" Aluminum Bi-Fold Doors 12M07 (Black) Standard 38ABF 12M08 (Brass) 38ABF-BB 12M09 (Brushed Stainless) 38ABF-BS ACCESSORIES AND COMPONENTS Chase T ermination 96L20 FTF8-CTT Arch T ype T ermination 96L22 FTF8-ATT Arch Type Termination 96L22 FTF8-ATT Ref.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 23 NOTES.
24 Printed in U.S.A. © 2006 by LHP P/N 700,033M REV . C 12/2006 The manufacturer reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté TOA Electronics CST38MH c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du TOA Electronics CST38MH - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation TOA Electronics CST38MH, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le TOA Electronics CST38MH va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le TOA Electronics CST38MH, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du TOA Electronics CST38MH.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le TOA Electronics CST38MH. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei TOA Electronics CST38MH ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
