Manuel d'utilisation / d'entretien du produit CST-38 du fabricant TOA Electronics
Aller à la page of 24
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 1 36" Wood Burning Fireplaces P/N 700,023M REV. C 06/2005 CST -38 CPF-38 MODELS CUSTOM SERIES This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace system.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 2 IMPORTANT: PLEASE READ AND UNDERSTAND THESE RULES TO FOLLOW FOR SAFETY. 1. Before starting your fireplace installation, read these installation instructions carefully to be sure you understand them completely and in entirety.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 3 Figure 1 TYPICAL INSTALLATION *Construction Materials: • framing materials • paneling • particle board • flooring • millboard • dry wall • plywood • etc. PRECAUTIONS Note: These fireplace systems are not difficult to install.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 4 For questions, please call your distributor or the manufacturer. Special restrictions apply to the front and facing of the fireplace and nearby walls (See pages 18, 19 and 20 ). CHIMNEY SYSTEM These fireplaces are designed and code listed for use with Security Chimneys FTF8 chimney System only.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 5 Figure 7 Figure 6 Carefully consider the position of the fireplace opening with respect to the location of adja- cent or nearby stairwells, bath or k.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 6 The safety strips should extend in front and sides of the fireplace opening 2" (51 mm) . In the event a wooden support is used to elevate the fi.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 7 FIREPLACE SPECIFICATIONS Figure 15 39 ¹⁄₄ " (997 mm) 23 ¹⁵⁄₁₆ " (608 mm) 25 ³⁄₁₆ " (640 mm) 8" (203 mm) Left.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 8 Figure 16 Figure 19 CPF CST Figure 17 Figure 18 Figure 21 CST - Front View CST - End View CPF - Right Front View CPF - End View FRAMING SPECIFICATIONS Figure 20 7" Min.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 9 Figure 22 FRAMING WALL VARIATIONS As many as six (6) different framed wall con- figurations can be constructed to enclose the CST and CPF fireplaces. The following illustra- tions depict these variations of wall enclosures.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 10 A minimum 2" (51 mm) air space must be reserved for all combustible materials extend- ing for any continuous length surrounding the chimney. Reference Figures 24 and 25 and charts “Fram- ing Dimensions for Ceiling and Roof” on page 8, which specify minimum ceiling and roof dimensions.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 11 Check vertical alignment of chimney pipe so that it projects from the roof in a true vertical position. Security's chimney sections do not need to be screwed together. Additional rein- forcement is not necessary, except in certain offset conditions (see to page 16, Figure 47 ).
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 12 Figure 40 Step 10. Using an FTF8-CTD Round Termi- nation: 1. Hold FTF8-CTD over top of last chimney section ( Figure 40 ). 2. Center inner slip section in inner flue pipe- slip down. 3. Center outer locking section over outer flue pipe.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 13 Figure 41 TEN FOOT RULE SUMMARY The minimum chimney height above the roof and/or to adjacent walls and buildings is speci- fied by all major building codes.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 14 11 0 11 1 0 0 0 279 0.28 17 1 5 0 1 0 0 432 0.43 21 ¹⁄₄ 19 ¹⁄₄ 2 0 0 0 540 0.54 27 ¹⁄₄ 23 ¹⁄₄ 1 1 0 0 692 0.69 35 2 11 0 0 1 0 889 0.89 47 3 11 0 0 0 1 1194 1.19 51 ¹⁄₄ 43 ¹⁄₄ 0 1 1 0 1302 1.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 15 A B FTF8-ES30 Number of FTF8 A B Offset Height Offset/Return FTF8-S4 Chimney Sections Offset Height (Inches) (Inches) Elbow Set Stabilizer 12" .
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 16 OFFSET ELBOW ASSEMBLY Offset elbows install the same as chimney sections. First, snap the inner section INTO the preceding inner section of flue. Check connec- tion by pulling up slightly to ensure a tight fit.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 17 There is a one-hand operated shut-off valve located in the enclosed corner of the fireplace opening behind the screen.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 18 GAS LINE INSTALLATION The CST and CPF fireplaces have been ap- proved to accept a ¹⁄₂ " (13 mm) gas line for an approved gas appliance. Always have the appli- ance installed by a qualified, licensed plumber in accordance with all local building codes.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 19 If there is a continuous perpendicular side wall closer than 18" (mm) from the CST-38 fireplace opening, it must be protected with a 40 x 40&qu.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 20 Example: Given that the required “R value” for a suitable hearth extension used must be equal to or greater than: “R” = r x T L = 1.19 x 1 " = 1.19. If it is desired to elevate a marble hearth exten- sion to a level of 5" or more above the floor surface.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 21 ACCESSORIES AND COMPONENTS 63L10 FTF8-12 63L13 FTF8-18 63L14 FTF8-36 Chimney Section 63L15 FTF8-48 Canadian (Outside) 62L92 FTF8-18C Chimney Section.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 22 Combustion Air Kit 011761 AK-4 (Less Duct) 011763 AK-4LD “All-Glass TM ” 38AEP Aluminum End Panel 38AEP-BB “All-Glass TM ” Cabinet Doors 38T.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 23.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 24 Printed in U.S.A. © 2001 by LENNOX HEARTH PRODUCTS P/N 700,023M REV. C 06/2005 The manufacturer reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté TOA Electronics CST-38 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du TOA Electronics CST-38 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation TOA Electronics CST-38, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le TOA Electronics CST-38 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le TOA Electronics CST-38, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du TOA Electronics CST-38.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le TOA Electronics CST-38. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei TOA Electronics CST-38 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
