Manuel d'utilisation / d'entretien du produit C-CV454D-9 CU du fabricant Toa
Aller à la page of 20
Thank you for purchasing TOA Outdoor Day/Night camera: Wide, Standard, or Tele. Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
2 T ABLE OF CONTENTS 1. SAFETY PRECAUTIONS ............................................................................... 3 2. GENERAL DESCRIPTION ............................................................................. 5 3. HANDLING PRECAUTIONS .
3 1. SAFETY PRECAUTIONS • Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation. • Make sure to observe the instructions in this manual as the conventions of safety symbols and messages regarded as very important precautions are included.
4 • Leave the installation of the unit to your TOA dealer because the installation requires expert experience and skills. The unit may fall off if incorrectly installed, resulting in possible personal injury.
5 2. GENERAL DESCRIPTION The TOA C-CV454 series are outdoor Day/Night cameras equipped with a 1/3" CCD. A lineup of cameras with three types of lenses, Wide, Standard, and Tele allows accurate monitoring over a wide range from near to distant subjects depending on the installation location.
6 ( 1 ) Vari-focal lens ( 2 ) Sunshade ( 3 ) Front cover ( 4 ) Mounting bracket (accessory) ( 5 ) Safety wire mounting hole ( 6 ) Sunshade fixing screw ( 7 ) Bracket mounting bolt (accessory) ( 8 ) Mo.
7 [Ceiling mounting example] [Wall mounting example] Bracket mounting bolt with washer , stainless steel (accessory) Camera mounting bolt M8 or W3/8 Safety wire mounting hole Note Install a safety wire as needed. Select the wire considering its length, diameter, and hook strength.
8 Camera mounting bolt M8 or W3/8 Camera mounting bolt M8 or W3/8 [Example 3: Mounting to a ceiling or wall] If only fine adjustment of camera angle is required; [Example 2: Mounting on a wall] If ang.
9 3. Install the camera unit to the mounting bracket using the supplied insulating spacers and Bracket mounting bolts (with washer, stainless steel). Note Be sure to position the insulating spacers between the bracket and bolt, as induction voltage or noise may be produced at the joints depending on installation conditions.
10 Fit the waterproof cap (shaded area) into place. 5. Attach the waterproof cap to the camera unit. Note If the waterproof cap is not secured to the mounting surface, water or moisture soaks in, causing the corrosion of the BNC connector. This may cause unit failure.
11 6. Connect the camera unit. Connect the camera unit to both the monitor and the power supply as illustrated below. Notes • If the Video output is not terminated at 75 Ω , camera images are not properly displayed. Make sure that the output has been terminated at 75 Ω at the connected monitor or switcher.
12 Loosen two sunshade fixing screws. T urn the sunshade, then extract it. 2. Connect the camera’s monitor output terminal to the monitor. Note: The camera will not operate if the monitor output terminal is connected to the camera drive unit. 3. Switch on the power supply.
13 Angle of view: ± 90° (T urn the Camera head) Projection Bracket mounting bolts Horizontal angle: ± 60° Camera mounting bolt V ertical angle: 90° (For the ceiling installation) Focus ring Zoom ring Mode setting switch Iris control The C-CV454D18 differ in positions of the focus ring and zoom ring; their positions are exchanged.
14 Sunshade fixing screw (Screw with captive washer M3x8) Slot to insert the sunshade fixing screw Sunshade Sunshade fixing screw After inserting the sunshade, turn clockwise to fix it in position (as shown), then secure it with the sunshade fixing screws.
15 Mode Setting Switch (Factory-preset setting) 1: Focus adjustment switch 2: Backlight compensation switch 3: Flickerless switch 4: A TW/AWB selection switch 5: Mode selection switch ATW D / N AWB COLOR F. A D J BLC 1/100 1/60 ON OFF ATW D / N AWB COLOR F.
16 ON OFF ON OFF ON OFF ON OFF 7.4. ATW/AWB selection switch: Set the white balance operation. ATW: Set to “OFF” position during normal use. The camera's white balance automatically changes as an object's color temperature varies. AWB: Set to “ON” when the difference between the displayed color and actual color is annoying.
17 Remedy Connect the cables correctly. Solder BNC plugs correctly. Focus the lens. Remove dirt on the lens. Adjust the level correctly in accordance with the instruction manual of the monitor. Focus the lens again after turning the Focus adjustment switch of the Mode setting switch to “ON” position.
18 9. SPECIFICA TIONS C-CV454D-3 (CU) C-CV454D-9 (CU) C-CV454D18 (CU) 24 V AC, 50/60 Hz or 12 V DC 4 W (300 mA, Maximum current: 800 mA) 1/3 type IT-CCD 771 (H) x 492 (V), 380,000 pixels 2:1 interlace Horizontal: 15.734 kHz, Vertical: 59.94 Hz VBS1.0 V(p-p), 75 Ω , RCA pin jack VBS1.
19 • Accessories Mounting bracket ..................................................................................... 1 Cable with waterproof cap (2 m) .............................................................. 1 Bracket mounting bolts (with washer, stainless steel) .
133-22-161-10 URL: http://www.toa.jp/.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Toa C-CV454D-9 CU c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Toa C-CV454D-9 CU - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Toa C-CV454D-9 CU, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Toa C-CV454D-9 CU va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Toa C-CV454D-9 CU, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Toa C-CV454D-9 CU.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Toa C-CV454D-9 CU. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Toa C-CV454D-9 CU ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
