Manuel d'utilisation / d'entretien du produit VLYNQ Port du fabricant Texas Instruments
Aller à la page of 49
TMS320DM644x DMSoC VLYNQ Port User's Guide Literature Number: SPRUE36A September 2007.
2 SPRUE36A – September 2007 Submit Documentation Feedback.
Contents Preface ............................................................................................................................... 7 1 Introduction .........................................................................................
A.2 Supported Ordered Sets ....................................................................................... 40 A.3 VLYNQ 2.0 Packet Format .................................................................................... 41 A.4 VLYNQ 2.X Packets .
List of Figures 1 VLYNQ Port Functional Block Diagram ................................................................................. 10 2 External Clock Block Diagram .................................................................................
List of Tables 1 VLYNQ Port Pins ........................................................................................................... 12 2 Serial Interface Width ..................................................................................
Preface SPRUE36A – September 2007 Read This First About This Document This document describes the VLYNQ™ communications interface port in the TMS320DM644x Digital Media System-on-Chip (DMSoC). Notational Conventions This document uses the following conventions.
www.ti.com Related Documentation From Texas Instruments SPRAAA6 — EDMA v3.0 (EDMA3) Migration Guide for TMS320DM644x DMSoC. Describes migrating from the Texas Instruments TMS320C64x digital signal processor (DSP) enhanced direct memory access (EDMA2) to the TMS320DM644x Digital Media System-on-Chip (DMSoC) EDMA3.
1 Introduction 1.1 Purpose of the Peripheral 1.2 Features User's Guide SPRUE36A – September 2007 VLYNQ Port The VLYNQ™ communications interface port is a low pin count, high-speed, point-to-p.
www.ti.com 1.3 Functional Block Diagram Slave config bus Interface Master config Interface bus VL YNQmodule VL YNQregister access CPU/EDMA initiated transfersto remotedevice Offchip (remote) deviceaccess ARM/EDMA memory System VL YNQ_SCRUN VL YNQ_CLOCK VL YNQ_RXD[3:0] VL YNQ_TXD[3:0] INT31 ARMinterrupt controller VLQINT 1.
www.ti.com 2 Peripheral Architecture 2.1 Clock Control CLKDIR=0 VL YNQ DMxxxdevice VL YNQ.CLK CLKDIR=0 VL YNQ VL YNQdevice CLKDIR=1 VL YNQ DMxxxdevice VL YNQ.
www.ti.com 2.2 Signal Descriptions 2.3 Pin Multiplexing 2.4 Protocol Description Peripheral Architecture The VLYNQ module on the DM644x device is configurable for a 1 to 4 bit-wide RX/TX. Chip-level pin multiplexing registers control the configuration.
www.ti.com 2.5 VLYNQ Functional Description Address translation commands Outbound Outbound command FIFO data Return FIFO data FIFO Return command Inbound FIFO Registers translation Address TxSM 8B/10B.
www.ti.com 2.5.1 Write Operations Address translation commands Outbound Outbound command FIFO data Return FIFO data FIFO Return command Inbound FIFO Registers translation Address TxSM 8B/10B encoding .
www.ti.com 2.5.2 Read Operations Address translation commands Outbound Outbound command FIFO data Return FIFO data FIFO Return command Inbound FIFO Registers translation Address TxSM 8B/10B encoding S.
www.ti.com 2.6 Initialization 2.7 Auto-Negotiation 2.8 Serial Interface Width Configuration Peripheral Architecture Note: Not servicing read operations results in deadlock.
www.ti.com 2.9 Address Translation Peripheral Architecture Remote VLYNQ device(s) are memory mapped to the local (host) device’s address space when a link is established (this is similar to any other on-chip peripherals).
www.ti.com Mapregion1 Mapregion2 Mapregion3 Mapregion4 0400:0000 (0C00:0000onCONFIGbus) 0800:0000 07FF:FFFF 0800:0100 0800:00FF 0801:0100 0801:00FF 0841:00FF Mapreg.
www.ti.com Peripheral Architecture DM644x VLYNQ Module: 0C00 : 0054h Initial address at the slave configuration bus 0000 : 0054h Initial address [25:0] at the slave configuration bus interface subtrac.
www.ti.com 2.10 Flow Control Peripheral Architecture Example 1. Address Translation Example The remote address 0x 0400 : 0154 (or 0x0000 0054) was translated to 0x 8200 : 0054 on the DM644x (local) device in this example.
www.ti.com 2.11 Reset Considerations 2.11.1 Software Reset Considerations 2.11.2 Hardware Reset Considerations 2.12 Interrupt Support 2.12.1 Interrupt Events and Requests Peripheral Architecture Peripheral clock and reset control is done through the power and sleep controller (PSC) module that is included with the device.
www.ti.com VL YNQinterrupt pending/setregister (INTPENDSET) VL YNQ Status/clear register (INTST A TCLR) OR T ransmitserial interruptpacket VLQINT (ARMINT31) 14 0 INTLOCAL VL YNQcontrolregister(CTRL) Serialbuserror (LERROR/RERROR) CPUwrites Serialinterrupt packetfrom remotedevice INTLOCAL=1 INTLOCAL=0 2.
www.ti.com 2.12.3 Remote Interrupts 2.12.4 Serial Bus Error Interrupts 2.13 DMA Event Support Peripheral Architecture Remote interrupts occur when an interrupt packet is received over the serial interface from a remote device.
www.ti.com 2.14 Power Management 2.15 Emulation Considerations Peripheral Architecture The VLYNQ module can be placed in reduced-power modes to conserve power during periods of low activity. The power management of the peripheral is controlled by the processor Power and Sleep Controller (PSC).
www.ti.com 3 VLYNQ Port Registers VLYNQ Port Registers Table 5 describes the address space for the VLYNQ registers and memory. Table 5. VLYNQ Register Address Space Block Name Start Address End Addres.
www.ti.com 3.1 Revision Register (REVID) VLYNQ Port Registers The revision register (REVID) contains the major and minor revisions for the VLYNQ module. The REVID is shown in Figure 9 and described in Table 7 . Figure 9. Revision Register (REVID) 31 16 ID R-1h 15 8 7 0 REVMAJ REVMIN R-2h R-6h LEGEND: R = Read only; - n = value after reset Table 7.
www.ti.com 3.2 Control Register (CTRL) VLYNQ Port Registers The control register (CTRL) determines operation of the VLYNQ module. The CTRL is shown in Figure 10 and described in Table 8 .
www.ti.com VLYNQ Port Registers Table 8. Control Register (CTRL) Field Descriptions (continued) Bit Field Value Description 7 INT2CFG Interrupt to configuration register. Determines which register is written with the status contained in interrupt packets that are received over the serial interface.
www.ti.com 3.3 Status Register (STAT) VLYNQ Port Registers The status register (STAT) is used to detect conditions that may be of interest to the system designer.
www.ti.com VLYNQ Port Registers Table 9. Status Register (STAT) Field Descriptions (continued) Bit Field Value Description 8 RERROR Remote Error. Write a 1 to this bit to clear it. 0 No error This bit indicates that a downstream VLYNQ module has detected a packet error.
www.ti.com 3.4 Interrupt Priority Vector Status/Clear Register (INTPRI) 3.5 Interrupt Status/Clear Register (INTSTATCLR) VLYNQ Port Registers The interrupt priority vector status/clear register (INTPRI) displays the highest priority vector with a pending interrupt when read.
www.ti.com 3.6 Interrupt Pending/Set Register (INTPENDSET) 3.7 Interrupt Pointer Register (INTPTR) VLYNQ Port Registers The interrupt pending/set register (INTPENDSET) indicates the pending interrupt status when the INTLOCAL bit in the control register (CTRL) is not set.
www.ti.com 3.8 Transmit Address Map Register (XAM) VLYNQ Port Registers The transmit address map register (XAM) is used to translate transmit packet addresses to remote device configuration bus addresses. The XAM is shown in Figure 16 and described in Table 14 .
www.ti.com 3.9 Receive Address Map Size 1 Register (RAMS1) 3.10 Receive Address Map Offset 1 Register (RAMO1) VLYNQ Port Registers The receive address map size 1 register (RAMS1) is used to identify the intended destination of inbound serial packets. The RAMS1 is shown in Figure 17 and described in Table 15 .
www.ti.com 3.11 Receive Address Map Size 2 Register (RAMS2) 3.12 Receive Address Map Offset 2 Register (RAMO2) VLYNQ Port Registers The receive address map size 2 register (RAMS2) is used to identify the intended destination of inbound serial packets.
www.ti.com 3.13 Receive Address Map Size 3 Register (RAMS3) 3.14 Receive Address Map Offset 3 Register (RAMO3) VLYNQ Port Registers The receive address map size 3 register (RAMS3) is used to identify the intended destination of inbound serial packets.
www.ti.com 3.15 Receive Address Map Size 4 Register (RAMS4) 3.16 Receive Address Map Offset 4 Register (RAMO4) VLYNQ Port Registers The receive address map size 4 register (RAMS4) is used to identify the intended destination of inbound serial packets.
www.ti.com 3.17 Chip Version Register (CHIPVER) 3.18 Auto Negotiation Register (AUTNGO) VLYNQ Port Registers VLYNQ allows inter-connection of many VLYNQ devices. In order for software to control the device functions, there must be a mechanism that allows the software to identify VLYNQ devices.
www.ti.com 4 Remote Configuration Registers Remote Configuration Registers The remote configuration registers listed in Table 25 are the same registers as previously described, but they are for the remote VLYNQ device.
www.ti.com Appendix A VLYNQ Protocol Specifications A.1 Special 8b/10b Code Groups A.2 Supported Ordered Sets Appendix A VLYNQ relies on 8b/10b block coding to minimize the number of serial pins and allow for in-band packet delineation and control. The following sections include general 8b/10b coding definitions and their implementation.
www.ti.com A.2.1 Idle (/I/) A.2.2 End of Packet (/T/) A.2.3 Byte Disable (/M/) A.2.4 Flow Control Enable (/P/) A.2.5 Flow Control Disable (/C/) A.2.6 Error Indication (/E/) A.
www.ti.com VLYNQ 2.0 Packet Format Table A-3. Packet Format (10-bit Symbol Representation) Description Field Value Description PKTTYPE[3:0] This field indicates the packet type. 0000 Reserved 0001 Write with address increment. 0010 Reserved 0011 Write 32-bit word with address increment.
www.ti.com A.4 VLYNQ 2.X Packets VLYNQ 2.X Packets An example of what can happen to a write burst due to remote and local FIFO state changes and the link pulse timer expiring is shown in Example A-1 . This protocol can be extended to apply to multiple channels; therefore, the data return channel is logically isolated from the command channel.
www.ti.com VLYNQ 2.X Packets A command, length, address, and start receive data from the idle stream. A flow enable was received for the command channel, but there is data to return, so the flow is followed by a channel 1 descriptor (the command for return data actually indicates a channel 1), and the channel 1 packet is now under way.
www.ti.com Appendix B Write/Read Performance B.1 Write Performance Appendix B The following sections discuss the write versus read performance and how the throughput (read or write) should be calculated for a given data width and serial clock frequency.
www.ti.com Write Performance Table B-1. Scaling Factors Burst Size in 32-bit words Data Bytes Overhead Bytes Scaling Factor 1 4 6 40% 4 16 7 69.56% 8 32 7 82.05% 16 64 7 90.14% Table B-2. Expected Throughput (VLYNQ Interface Running at 76.5 MHZ and 99 MHZ) Interface Running at 76.
www.ti.com B.2 Read Performance Read Performance Since reads must complete a transmit-remote read-receive cycle before starting another read transaction, the data throughput is lower as compared to writes.
www.ti.com Appendix C Revision History Appendix C Table C-1 lists the changes made since the previous version of this document. Table C-1. Document Revision History Reference Additions/Modifications/Deletions Section 2.9 Changed fourth paragraph. Added NOTE.
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Texas Instruments VLYNQ Port c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Texas Instruments VLYNQ Port - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Texas Instruments VLYNQ Port, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Texas Instruments VLYNQ Port va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Texas Instruments VLYNQ Port, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Texas Instruments VLYNQ Port.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Texas Instruments VLYNQ Port. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Texas Instruments VLYNQ Port ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
