Manuel d'utilisation / d'entretien du produit TR-300 du fabricant Telex
Aller à la page of 38
Telex Operating Instructions PROFESSIONAL WIRELESS INTERCOM SYSTEM TR-300, BTR-300 R Ext Intercom Aux Audio 1 3 4 2 Portable Station Connect BTR-300 Talk Headset Controls Volume Power Headset Portable.
TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION GENERAL DESCRIPTION This manual covers the BTR-300 Base Station and the TR-300 Portable Transceiver. The RadioCom Models BTR-300 and TR-300 were specifically designed to provide the user .
The system operates on selected frequencies within the 150-216 MHz band. The BTR-300 system is fully compatible with a number of other wired intercom manufactur- ers units. See the BTR-300 Setup Section for additional information. The TR-300 Transceiver operates in the con- tinuous transmit mode with the audio acti - vated by a switch.
BTR-300 BASE STATION TRANSCEIVER TECHNICAL INFORMATION -3- SPECIFICATIONS BTR-300 Input Power (minimum) ....................................................................................12V AC/DC at 360 mA Intercom Output ........330 mV (Low) or 1 V (Hi) RMS into 300 ohm load typical (at rated deviation) Intercom Input (Gain Minimum) .
FEATURES The RadioCom Model BTR-300 is a Base Station with one transmitter and four re - ceivers. It is designed for portable two way communication with the capability for inter- face to other audio systems.
CONTROLS and CONNECTIONS FRONT PANEL (Refer to Figure 3) Power ON/OFF Switch: Push this switch once to turn power ON; push it again to turn the power OFF. Power ON Indicator: The Power ON light is illuminated when the Power ON/OFF Switch is pushed in the ON Position.
External Intercom Switch, Level Control, and indicator: This switch enables the wired intercom interface when “IN”, and disables it when “OUT”. For RTS intercoms, the “IN” position is channel 1 and the “OUT” position is channel 2. A screwdriver adjustable control is provided to control the input level of the wired intercom.
-7- Ext Intercom Aux Audio 1 3 4 2 Portable Station Connect BTR-300 Tal k Headset Controls Volume Power Headset Portable Transmit On Gain O/M Push Twice to Latch RadioCom ä POWER ON INDICA TOR POWER .
-8- PUSH PUSH T ransmit Antenna Auxiliary Audio Output Auxiliary Audio Input Headset Mic Dyn Elt Off Remote Cont Loop Thru Intercom Intercom Loop-Thru Speaker Power AC/DC 12V 700 mA T ransmit AUXILIAR.
TR-300 BELT-PACK TRANSCEIVER TECHNICAL INFORMATION -9- SPECIFICATIONS TR-300 Overall Power Requirements ..............................................................6 AA cells (Alkaline, NEDA, MN 1500) Nickel-metal hydride optional Current Drain ....
FEATURES · Lightweight, small size and is self-contained. · 2 separate antennas, one for transmit, the other for receive. · Push-to-Talk with Lock-to-Talk feature switch for the TR-300 and Push-to-Transmit with Lock-to-Transmit feature for the TR-300P.
Figure 6 External Controls, TR-300 -11- Bat/ ovmod talk talk BEL T CLIP LOW BA TTER Y / OVERMODULA TION INDICA T OR LIGHT T ALK INDICA T OR LIGHT PUSH-TO-T ALK/ LOCK-TO-T ALK SWITCH VOLUME OFF/ON CONT.
Figure 7 Internal controls, TR-300 INTERNAL CONTROLS (Refer to Figure 7) Microphone Gain Control: Screwdriver ad- justable by removing belt clip and prying out the small rubber plug to the right of the screw boss.
EQUIPMENT SET-UP BTR-300 SET-UP UNPACKING Unpack your BTR-300 and TR-300 System. If there are any damages or shortages, refer to the “Warranty Service Information” section in this manual.
Table 3 Pin Wiring for Rear Panel Jacks Figure 8 Internal Intercom Switches -14- Internal Auxiliary Audio Out Auxiliary Audio Input Intercom Loop Thru Switch (both jacks) Settings Pin 1 Pin 2 Pin 3 Pin1 Pin 2 Pin 3 Pin 1 Pin 2 Pin 3 T elex Audio Com Ground 600 ohm 600 ohm Ground 2.
RACK MOUNTING To rack mount the BTR-300 base transceiver do the following: Remove the front two #6-32 x 3/8” screws on each side of the transceiver as shown in Figure 9. Place the rack mount brackets (supplied) on either side of the unit and insert three #6-32 x 3/8” screws for each bracket.
ANTENNA INFORMATION ANTENNA CONNECTIONS The BTR-300 is supplied with two (2) anten- nas. One 5/8-wave antenna for Transmit and one 5/8-wave antenna for Transmit and one 5/8-wave for Receive. Assemble the 5/8-wave antenna by screwing the two sections together as shown in Figure 10.
Remoting Antennas: It will be necessary to remote both the transmit and receive antennas on the BTR-300 when it is rack mounted. Connect the coax cable assembly (not sup - plied), to the receive antenna receptacle and mount the 5/8-wave antenna. The antenna can be attached to either a wall mount bracket or a microphone stand bracket (not supplied).
ANTENNA POLARIZATION The Telex Wireless Intercom System is “Ver- tically Polarized”. This means both the trans- mitting and receiving antennas should operate in the vertical position.
Attempting to operate the wireless intercom system through or around walls, ceilings, metal objects, etc. will reduce system range and performance. SIGNAL REFLECTION OFF A MET AL OBSTRUCTION CAUSES RE.
LOCAL HEADSET CONNECTION Insert the headset/microphone into the 4 pin XLR connector on the front panel. See the mi- crophone connection diagram (Figure 2) if other than a Telex Headset is used.
INTERCONNECTION to a HARD-WIRED INTERCOM SYSTEM The RADIOCOM wireless system can be integrated into Telex intercom systems and most existing wired intercom systems includ- ing RTS and Clearcom.
Figure 22 Connecting Two BTR-300’s CONNECTING AUXILIARY AUDIO SYS - TEM Connect the BTR-300 to your auxiliary audio via the Auxiliary input/output receptacles on the rear of the unit. CONNECTING BTR-300’s Connect the first BTR-300 to other BTR-300s by using short XLR type cables (not supplied) plugged into either of the intercom jacks.
TR-300 SET-UP HEADSET CONNECTION Inset the headset/microphone into the connec- tor on the bottom of the unit. See the connec- tion diagram (Figure 5) if headsets other than Telex are used.
PRE-WALK-THRU CHECKLIST Following the instructions fully to this point, you have successfully completed the follow- ing checklist: Set (if necessary) the internal inter- com switches to correspond with the wired intercom. Located the BTR-300 transceiver properly.
SYSTEM OPERATION BTR-300 OPERATION POWER If you have followed the instructions until this point, you should now be ready to turn both the TR-300 and the BTR-300 “ON”. Place the power switch on the BTR-300 in the “ON” position. The red power on indicator light should illuminate.
TR-300 OPERATION POWER You should now be ready to turn the TR-300 “ON”. Rotate the OFF/ON Volume Control Switch on the TR-300 clockwise to turn the unit on. BATTERY CHECK As you turn the unit on, note that the battery light (labeled bat/ovmod) should flash one or more times with good batteries.
ENABLING AUDIO PORTABLE TRANSCEIVERS Select the TR-300 portables that will be used with the BTR-300. Push in the portable enable switches that correspond to the TR-300 remotes that you will be using. The numbers of the portable stations (1, 2, 3, and 4), are the last digit of the product number on the back of the TR-300.
SETTING SYSTEM GAIN LEVELS ADJUSTING GAIN The gain may need to be adjusted for various audio conditions. The overmodulation light will indicate when the gain is too high. If the light is illuminated when you are talking, the gain is too high and will need to be decreased.
INTERCOM GAIN If the audio volume at the intercom input is too high, the light will be illuminated when the person on the intercom is talking. De - crease the gain until the light does not illumi- nate while talking at normal volume. Occasional flashing of the light is allowable.
TROUBLESHOOTING Reread the sections of this manual to make sure you have completed system set-up prop- erly. If you are unable to solve the problem, con- tract the dealer from whom you purchased the system for assistance. -30- PROBLEM SOLUTION DISTORTION - System’s audio quality seems distorted at medium to high input levels.
BATTERY INFORMATION GENERAL Improper battery selection, use, installation, and care are the cause of numerous wireless system failures. Alkaline Batteries: Alkaline batteries such as Mallory’s DURACELL or Everready’s EN - ERGIZER provide the most reliable operation in wireless transceivers.
BC-300NM2 BATTERY CHARGER NOTE: The BC-300NM2 is not supplied with the TR-300. See “Accessory” Section for or- dering information. Remove the battery holder from the TR-300. CAUTION DO NOT ATTEMPT TO CHARGE ANY ALKALINE BATTERIES WITH THIS CHARGER.
ACCESSORIES AB-300 Microphone Stand/Surface Mount Bracket - for 5/8-wave antenna. Includes necessary hardware. Order No. 63906-100 25’ Coax Cable Order No. 63901-000 4’ Coax Cable Order No. 63901-001 5/8-Wave Antenna - Screw apart for easy storing.
-34- CUSTOMER SERVICE INFORMATION If your receiver or transmitter should need servicing under the warranty, please contact: Customer Service Department TELEX COMMUNICATIONS, INC. 8601 East Cornhusker Highway, P.O. Box 5579, Lincoln, Nebraska 68505-5579 U.
-35- FCC INFORMATION The Telex Models BTR-300 and TR-300 transceivers are Type Accepted under United States Federal Communications Commission Parts 90 and 74. Licensing of Telex equipment is the user’s responsibility and licensability depends upon the user’s classification, user’s application, and frequency selected.
R PN 803008-2 JAN 2001 Made in U.S.A TELEX COMMUNICATIONS, INC. 12000 Portland Ave. South, Bur nsville, MN 55337, U.S.A..
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Telex TR-300 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Telex TR-300 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Telex TR-300, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Telex TR-300 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Telex TR-300, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Telex TR-300.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Telex TR-300. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Telex TR-300 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
