Manuel d'utilisation / d'entretien du produit Phaser 740 du fabricant Tektronix
Aller à la page of 44
® www .tek.com/Color_Print ers/ P H A S E R ® 7 4 0 a n d 7 4 0 L LA SER PRIN T ERS User Guide.
0 Contents Tektronix Supplies 1 Getting The Most From Your Printer 2 Printing 3 All About Media 4 Loading Media Trays 7 Using the Multi-Purpose Tray 8 Duplex Printing 16 Front Panel Messages 20 Troubl.
1 T o order supplies and accessories, contact y our local dealer or visit the T ektronix web site: www .tek.com/Color_Printers/supplies Accessories Order n umber Description Paper T rays 436-0282-02 A/Letter (U.S.) 436-0283-02 A4 (Metric Letter) 436-0314-02 Legal T ransparency T rays 436-0284-02 A/Letter (U.
2 Getting The Most Fr om Y our Printer Supplies Startup Kit Z740SS Option 01 for Metric ■ 4 Standard color T oner Car tridges (CMYK) ■ Glossy Coated Paper (100 sheets) ■ T ektronix T ransparencies (50 sheets) Color Kit Z740LCS Converts a Phaser 740L color -capable printer to a full-color printer: ■ Adds three color toners.
3 Print Quality Modes Standard ■ General-purpose mode for full-color printing. Premium Monochr ome ■ Highest-quality monochrome (gray scale) prints. Premium Requires Plus Featur es ■ Highest-quality color prints. ■ Near -photographic detail. Fast Monoc hrome ■ Fastest gray scale printing.
4 All About Media P aper T ra ys Load only laser paper in the paper tra ys; specialty media (such as glossy paper , card stock, en velopes , and labels) must be loaded in the Multi-Pur pose T ra y . Laser paper only ■ T ray sizes: A/Letter A4 Legal ■ 60 - 90 g/m 2 , 16 - 24 lb.
5 Multi-Purpose T ray Laser paper ■ A/Letter A4 Legal ■ 75 - 150 g/m 2 , 20 - 40 lb. T ektronix transparencies ■ A/Letter A4 T ektronix Glossy Coated paper ■ A/Letter A4 Laser labels ■ A/Letter A4 ■ Recommended Avery ™ labels (U.
6 Supported page siz es and ima g e area The printer supports four media sizes, which you select in the Print screen (using a supported printer driver). Margins Media Pa g e size Print area T op / Bottom Sides 1 Letter 8.5 x 11 in. 8.2 x 10.6 in. .2 in.
7 Loading Media T ra ys 1 Push down on the tray’ s metal plate until it clicks, locking it in place. 2 Fan the media to release sheets that ar e stuck together . 3 Place the media in the tray under the hooks. 4 T ransparencies: Place the T ektronix logo strip face-up under the hooks.
8 Using the Multi-Purpose T ra y 1 Adjust the guides for the width of the media. 2 Adjust the Media Thic kness switch for the media you are using (see page 9). 3 Insert the media, printing side face-up (for T ektronix transparencies, the logo strip is face-down ).
9 Setting Media Thickness Manually select a media thickness for the most reliable paper -picking from the Multi-Purpose T ray . 1 Open the left side door .
10 Loading specialty media En velopes T ektronix T ransparencies Letterhead Laser Labels Ne ver use en velopes with windows or metal clasps; they will damage the printer . Use env elopes that are at least #10-size . Ne ver use media f or inkjet printers; inkjet media may damage the Fuser .
11 P aper 2nd Side T ektronix F abric T ransfer T ektronix Glossy Coated P aper F or best results on double-sided printing, use 90 g/m 2 (24 lb . bond) laser paper.
12 Printing En velopes 1 Prepar e each envelope: tuck in the envelope flap. 2 Adjust the printer’ s media thickness switch to Thick . 3 Adjust the printer’ s media guides for the width of your envelopes.
13 7 In your application: ■ Create a document with these measur ements: ■ Access the P age Setup menu and make these selections: 8 In the Print scr een (using a supported printer driver), make this selection and send the job to the printer . ■ Width: 4.
14 Printing on labels Recommended Avery ™ labels: At the printer 1 Adjust the printer’ s media thickness switch to Thick . 2 Insert the label sheets (maximum capacity is 30 sheets): ■ Side to be printed is face-up . ■ The top of the sheet enters the printer first .
15 In the application 1 If your application has a setting for Avery ™ labels, use it as a template. Otherwise, refer to the instructions included with the labels for margin settings. 2 In the Print scr een, select the Multi-Purpose T ray . Send the job to the printer .
16 A utomatic Duplex Printing A utomatic duple x printing requires that the Lower T ray Assemb ly be installed. 1 Make sure that the Duplex Unit is inserted in the printer’ s upper ( a ) slot. 2 Load 75 - 90 g/m 2 (20 - 24 lb.) paper in the paper tray .
17 4 Decide on a binding prefer ence (how the page turns) for Step 5 : 9102-50 Landscape Portrait Long edge Short edge 5 In the Print scr een, select the Duple x option and a binding prefer ence: Macintosh Drivers: LaserWriter 8.5.1 ■ From the pull-down menu, choose La yout .
18 Manual Duple x Printing: Multi-Purpose T ray Side 1 F or a multi-page document, print odd-numbered pages for Side 1 . (This selection is application-specific). 1 Insert paper with the side to be printed face-up . This example shows letterhead paper .
19 Side 2 F or a multi-page document, print even-numbered pages f or Side 2 . (This selection is application-specific). 1 Insert the paper with the blank side face-up .
20 Fr ont P anel Messages Message Action Pag e <color>:low The displayed color T oner Cartridge is running out; replace it soon. Energy Star Mode Wake Up Menu The printer is in energy conservation mode. Press the Wake Up button on the front panel or send a print job to bring the printer to Ready .
21 T r oubleshooting Print Quality If you notice a problem with the quality of your prints, the probable solution is r eplacing one of the consumables. Keep in mind this basic guideline: ■ If the symptom appears in a single color: Replace the T oner Cartridg e .
22 Symptom: In one color only? Solution: Replace that color T oner Cartridge . 1 color has many vertical streaks. Replace the T oner Cartridge. 1 color has a light vertical streak. 1 color is light or faded. 1 Adjust the color density (see page 38). 2 Replace the T oner Cartridge.
23 Symptom: In all four colors? Solution: 1) Choice of media or 2) Replace Imaging Unit, or Fuser , or Fuser Roll. Streak thr ough all 4 colors. 1 Use T ektronix media. 2 Use the correct media tray for the media you are using. 3 When using the Multi-Purpose T ray , select the correct media in the front panel.
24 Symptom: In all four colors? Solution: 1) Choice of media or 2) Replace Imaging Unit, or Fuser , or Fuser Roll or Main Charge Grid. Prints are black (edge to edge). 1 Remove, then re-insert the Main Charge Grid. 2 Replace the Main Charge Grid. Hints ■ Use T ektronix media.
25 Symptom: In all four colors? Solution: 1) Choice of media or 2) Replace Imaging Unit, or Fuser , or Fuser Roll or Main Charge Grid. Pieces of the printed image are missing and reappear out of place, approximately 129 mm (5 in.) down the page. or Media frequently wraps ar ound the Fuser ( Jam at C ).
26 Media Jams Preventing media jams ■ T o reduce the frequency of media jams, use T ektronix media and occasionally clean the rollers. See page 32. ■ When using the Multi-Purpose T ray , always set the media thickness switch for the media you are using.
27 Jam at A Solution 1 Open the left side door; remove the jammed media. Solution 2 Remove the media tray; remove the jammed media from inside the printer . 33100-08 33100-09 Jam at B Solution 1 Open the lower left side door and remove the jammed media.
28 Jam at C 1 Remove the Fuser: a Open the printer’ s front door . b T urn the small blue thumbscrew counterclockwise to unlock the Fuser . c Press the safety catch and slide the Fuser out of the printer . 2 Remove the Fuser Roll: a Press out on the two tabs to unlock the Fuser Roll.
29 Jam at D The Fuser is hot. T o av oid personal injur y , use caution or wait f or it to cool before touching it. Solution 1 1 Open the front door . 2 Pull open the access door; the media is visible. 3 T urn the Fuser’ s large blue knob counterclockwise .
30 Jam at E Solution 1 Remove the jammed media from the output tray . Solution 2 Pull open the access door (above the plastic output tray) and remove the media.
31 Jam at Duplex Unit 1 Remove the Duplex Unit (it is in the printer’ s upper slot). 2 Open the Duplex Unit. 3 Remove the jammed media. 4 Close the Duplex Unit; press down to make sure that it snaps shut. 5 Re-insert the Duplex Unit into the printer’ s upper slot.
32 Occasional Cleaning If your printer experiences frequent media jams, clean the r ollers. Instructions are included in these locations: ■ Cleaning menu in the fr ont panel ■ Video clips on the printer’ s CD-ROM Print the cleaning instructions 1 On the printer’ s front panel, press Menu .
33 Printing Help P ages from the Fr ont Panel The front panel contains pages to help you use the printer and diagnose print quality . 1 On the printer’ s front panel, press Menu ; you see this message: 2 Press Menu ; you see this message: 3 Press <--- or ---> to scr oll to any of these help pages: 4 Press Print .
34 Consumables Inf ormation Using the Consumables P age ■ T oner life remaining: ■ % Remaining gauge for all other consumables ■ Count ■ A verage T oner Co verage per Color ■ Date of install.
35 Using the Usage Profile Report Provides in-depth information on printer usage: ■ Consumables used ■ T ray and media selections ■ Printer interventions ■ Analysis of usage rates For detailed information on the Usage Profile report, refer to “Printer Management” on the printer’ s CD-ROM or web site.
36 Using PhaserLink ™ software PhaserLink software, using W orld Wide Web technology , provides these printer management tools: ■ Print job status ■ Printer usage ■ Routine troubleshooting ■ Configuration of printer settings PhaserLink requir es a TCP/IP connection.
37 Replacing Consumables Detailed, illustrated replacement instructions ar e shipped with each replaceable component. Component A verage Life* T oner Hi-capacity cartridges 10,000 pages (CMY) 12,000 p.
38 Contr olling Color Density When colors look faded, adjust the toner color density to extend the life of the components. Print and use the Color Reference P age 1 In the printer’ s front panel, scroll to Calibrate Colors , press Menu and print the Color Reference Page.
Color Density Samples Phaser ® 740 Color Laser Printer Color Density Samples Phaser ® 740 Color Laser Printer.
40.
41 Getting More Inf ormation Find detailed printer information in any of these locations. Printer CD-ROM T ektronix W eb Site ■ Advanced Features and T roubleshooting ■ Consumables instructions .
42 Getting Help Online Services Supplies Information on local T ektronix dealers : W orld Wide Web: T ekSMART ™ Knowledge Base: T echnical support: Current software: Anonymous ftp server: Subscribe to email update notices: www .tek.com/Color_Printers/ www2.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Tektronix Phaser 740 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Tektronix Phaser 740 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Tektronix Phaser 740, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Tektronix Phaser 740 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Tektronix Phaser 740, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Tektronix Phaser 740.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Tektronix Phaser 740. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Tektronix Phaser 740 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
