Manuel d'utilisation / d'entretien du produit R9002031 du fabricant Barco
Aller à la page of 45
R9002031 R9002038 INST ALLA TION MANUAL DA T A 808s.
BARCO PROJECTION SYSTEMS Date : 170397 Art. No. : R5975607 R9002031 R9002038 INST ALLA TION MANUAL DA T A 808s.
Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, March 1997. All rights reserved. Trademarks are the rights of their respective owners.
Table of contents i-1 5975607 BARCODATA 808s 110397 TABLE OF CONTENTS .............................................................................................................. .................. I-1 SAFETY INSTRUCTIONS On saf ety ................
Table of contents i-2 5975607 BARCODATA 808s 110397 Connecting a Component Video source to Port 4/5 ............................................................................. 7 - 3 Connecting a RGB Analog source with Tri-level sync to Port 4/5 (option) .
Safety instructions 1-1 5975607 BARCODATA 808s 110397 1 SAFETY INSTRUCTIONS Projectors are built in accordance with the requirements of the international safety standards IEC950, UL 1950 and CSA C22.2 No. 950, which are the safety standards of information technology equipment including electrical business equipment.
Safety instructions 1-2 5975607 BARCODATA 808s 110397 unless proper ventilation is provided. On servicing Do not attempt to service this projector yourself, as opening or removing covers may expose you to dangerous voltage potential and risk of electric shock! Refer all projector service to a qualified BARCO service center.
Unpacking and dimensions 2-1 5975607 BARCODATA 808s 110397 2 UNP ACKING AND PROJECT OR DIMENSIONS Unpacking Contents of the shipping carton : ρ 1 BARCODATA 808s projector ρ 1 Remote Control Unit plus 1 battery 9V ρ 1 power cord with outlet plug type CEE7 or ANSI 73.
Unpacking and dimensions 2-2 5975607 BARCODATA 808s 110397 Projector dimensions (in mm) 1040 A 596 169. 5 ROTATION COVER *SERVICE* GRAVITY POINT CRT POINT 362 B 286 226 170 84 27 45.
Installation guidelines 3-1 5975607 BARCODATA 808s 170397 3 INST ALLA TION GUIDELINES Installation guidelines Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to optimize the use of the projection system.
Installation guidelines 3-2 5975607 BARCODATA 808s 170397 Where to install the projector ? To indicate a correct installation position it is necessary to know : The distance from projector to ceiling in case of Ceiling mounted or the distance from projector to floor in case of Table mounted; The distance from projector to screen.
Installation setup 4-1 5975607 BARCODATA 808s 170397 4 INST ALLA TION SETUP Removing the top cover During some installations, it will be convenient to remove the top cover from the projector totally.
Installation setup 4-2 5975607 BARCODATA 808s 170397 Scan Adaptation The scan switches must be placed in the correct position which corresponds to the desired scanning configuration. To change the scanning, it is necessary to remove the projector top cover and to open the protection plate.
Installation setup 4-3 5975607 BARCODATA 808s 170397 - Press the module lock and lift up the module handle; - Repeat this action on both sides of the module and extract the module out of the main frame.
Installation setup 4-4 5975607 BARCODATA 808s 170397 To check the current positions of the scan switches, proceed as follows: Attention : This procedure can only be done after power (mains) connection. So, first continue with the projector setup and the connections and then return to this procedure.
Projector setup 5-1 5975607 BARCODATA 808s 170397 5 PROJECT OR SETUP StdBY MA IN POWER PROC ESSOR CY C BLOC K MATC H ERROR RCU RCV DS PC PA US E PRO J EC TO R A DDRES S (sum ) OF F ON BAUD R A T E T A.
Projector setup 5-2 5975607 BARCODATA 808s 170397 1 128 2 6 4 3 3 2 4 1 6 5 8 6 4 7 2 8 1 Setting the address is a hardware SETUP of your projector which must be done during installation. Use the 8 DIP switches provided on the controller board labelled 'Projector Address'.
Projector setup 5-3 5975607 BARCODATA 808s 170397 Position of DIP switches and baud rate codes : Baud Rate for communication with a computer The communication speed between the projector and the computer has 8 possible settings. With DIP Switch No. 6, No.
Projector setup 5-4 5975607 BARCODATA 808s 170397.
AC power connection 6-1 5975607 BARCODATA 808s 170397 6 AC POWER CONNECTION AC Power (mains) cord connection Use the supplied cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the back of the projector.
AC power connection 6-2 5975607 BARCODATA 808s 170397 AC Power check Check the power voltage which is determined by the ART. NR. (Article number) included in the label pasted on the backside of the projector. Projectors with the ART. NR. R9000901 and R9000902 must be connected to a 230 VAC power source.
AC power connection 6-3 5975607 BARCODATA 808s 170397 Switching on the projector Push the power (mains) switch located on the rear panel of the projector to switch the projector ON and OFF : If th.
AC power connection 6-4 5975607 BARCODATA 808s 170397.
Source connections 7-1 5975607 BARCODATA 808s 170397 4/5 Component video 8 with Tri-level sync R, G and B with composite sync on Green; 3 RGB 3 R, G and B with separate composite or with separate Horizontal and Vertical sync. Port No Projector input Numeric button Description of input signal 1 Composite Video 1 S-video : Y/C (luma/chroma).
Source connections 7-2 5975607 BARCODATA 808s 170397 Connecting a S-Video (or Composite Video) source to Port 2 Separate Y-luma/C-chroma signals for higher quality playback of Super VHS signals can be connected to Port 2 . The composite video can also be connected to this port.
Source connections 7-3 5975607 BARCODATA 808s 170397 RGB Input Auto Sync Tracking Module Procedure to remove the line termination resistors : Turn off the projector and unplug the projector power cord. Remove the top cover from the projector (see p.
Source connections 7-4 5975607 BARCODATA 808s 170397 Connecting a RGB Analog source with Tri- level sync to Port 4/5 (option) RGB analog input terminals with Tri-level sync input or with Tri-level sync on green can be connected to the projector via Port 4/5.
Installation adjustment mode 8-1 5975607 BARCODATA 808s 120397 8 INST ALLA TION ADJUSTMENT MODE Before starting any adjustment. The BARCODATA 808s is factory optimized for a screen with range 1.9m (74.8 inch) to 3.2m (126.0 inch) You wish an optimal focused image for a screen width between 1.
Installation adjustment mode 8-2 5975607 BARCODATA 808s 120397 Adaptation procedure : 1. Open and remove the top cover LENSES Le ns nut 2. Remove the lenses by : - remove for each lens the 4 nuts, holding lens to picture tube support (nutdriver 8 mm).
Installation adjustment mode 8-3 5975607 BARCODATA 808s 120397 Access to Installation Adjustment Mode It will be necessary to perform several mechanical adjustments while in the Installation Adjustment Mode. It will be required to open and remove the projector's top cover in order to gain access to the adjustment points.
Installation adjustment mode 8-4 5975607 BARCODATA 808s 120397 Optical Lens Focusing The optical focusing procedure is performed separately for each lens. The appropriate CRT will be switched on as the user proceeds through the optical focusing adjustment sequence.
Installation adjustment mode 8-5 5975607 BARCODATA 808s 120397 Raster Centering The raster must be centered on the CRT faceplate of each tube, therefore, it is necessary to look into the lenses.
Installation adjustment mode 8-6 5975607 BARCODATA 808s 120397 CRT Projection Angle Adjustment The projection angle of the red and blue CRT's is dependent on the desired size of the projected image. If the centers of green, blue and red do not coincide, the CRT projection angle must be adjusted.
Installation adjustment mode 8-7 5975607 BARCODATA 808s 120397 Loosen bolts E, F, G and H to pivot the blue CRT until the center of the Blue image and the center of the Green image coincide. When the angle of the blue CRT is corrected, tighten the four bolts.
Installation adjustment mode 8-8 5975607 BARCODATA 808s 120397.
Messages, warnings and failure codes 9-1 5975607 BARCODATA 808s 120397 9 MESSAGES, W ARNINGS AND F AILURE CODES SOURCE 01 Fh= 15.6 kHz Fv= 050 Hz SOURCE 01 Fh= 15.6 kHz Fv= 050 Hz Announcement of the selected source. enter password xxxx Message to enter your password.
Messages, warnings and failure codes 9-2 5975607 BARCODATA 808s 120397 WARNING : go to stand by Projector will switch to 'Standby' when the RCVDS is no longer available. WARNING : invalid frequency input The entered frequency or applied frequency of the source is out of the projector's range.
Appendix A: BARCO ceiling mount support A-1 5975607 BARCODATA 808s 170397 A BARCO CEILING MOUNT SUPPORT This appendix gives only an overview of the contents of the installa- tion guidelines and some overview drawings. The installation guidelines for the BARCO ceiling mounting support can be ordered from BARCO.
Appendix A: BARCO ceiling mount support A-2 5975607 BARCODATA 808s 170397 Projector position corrections Water-level adjustment D Projector axis adjustment C.
Appendix B: G2 adjustment B-1 5975996 BARCODATA 808s 170397 B G2 ADJUSTMENT Once the on-screen menu "G2 ADJUSTMENT" is displayed, proceed as follows : < E X IT > t o re tu rn Use the potent iometer s on the G2-ADJ. module t o set t he scr een gri d vol t age for Red, Green and B lue.
Appendix B: G2 adjustment B-2 5975607 BARCODATA 808s 170397.
Gamma corrections C-1 5975607 BARCODATA 808s 170397 C GAMMA CORRECTIONS When entering the gamma corrections, a warning will be displayed : "RISK OF INCORRECT ADJUSTMENT OF THE PROJECTOR.
Gamma Corrections C-2 5975607 BARCODATA 808s 170397 To carry out the Red and Blue Midlights Correction : Push the control stick forward or backward to highlight the item R & B MIDLIGHTS in the menu and then press the <ENTER> key. If the <EXIT> key is pressed, the projector will return to the Service menu.
FORMULA OUTSIDE PACKAGE DIMENSIONS (Inches) CHEMICAL FAMILY FEDERAL STOCK NUMBER (FSN) GROSS WEIGHT (LBS) % TRESHOLD LIMIT VALUE (Units) ALLOYS AND METALLIC COATINGS % % PIGMENTS SOLVENTS ADDITIVES CATALYST VEHICLE HAZARDOUS MIXTURES OF OTHER LIQUIDS, SOLIDS, OR GASES APPEARANCE AND ODOR BOILING POINTS (°C.
STABILITY UNSTABLE STABLE CONDITIONS TO AVOID INCOMPATABILITY (Materials to avoid) HAZARDOUS DECOMPOSITION PRODUCTS HAZARDOUS POLYMERIZATION WILL NOT OCCUR CONDITIONS TO AVOID MAY OCCUR STEPS TO BE TA.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Barco R9002031 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Barco R9002031 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Barco R9002031, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Barco R9002031 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Barco R9002031, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Barco R9002031.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Barco R9002031. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Barco R9002031 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
