Manuel d'utilisation / d'entretien du produit Futura 131G du fabricant Stoelting
Aller à la page of 33
Endura/Futura 131G OWNER'S MANUAL Manual No. 513536-4 Feb. 2004, Rev . 0.
.
Need Part s or Service? We stock the parts you need. Our Technicians are factory trained and are certified in the Stoelting Technicare program. Model No.: _______________________ Serial No.: _______________________ Purchase Date: ____________________ Start-Up Date:____________________ CALL Distributor: _________________________ Phone No.
.
This manual provides basic information about the freezer . Instructions and suggestions are given covering its operation and care. The illustrations and specifications are not binding in detail.
.
T ABLE OF CONTENTS SECTION 1 - SPECIFICA TIONS .................................................................................. 1 1.1 Description .......................................................................................................
Fig. Description Page 1 Model Endura/Futura 131G Freezer ................................................................... 1 2 Specifications .................................................................................................... 1 3 W arning Label Locations .
1 1.1 DESCRIPTION The Stoelting Endura/Futura 131G counter freezer is grav- ity fed. The freezer is equipped with fully automatic controls to provide a uniform product. The freezer is designed to operate with almost any type of commercial soft serve or non-dairy mixes available, including ice milk, ice cream, yogurt, and frozen dietary desserts.
2 MODEL ENDURA/FUTURA 131G COUNTER MODEL GRAVITY FREEZER Dimensions: Freezer: 22" (56 cm) wide x 28" (72 cm) deep x 34.75" (88 cm) high Crated: 28" (71 cm) wide x 35" (89 cm) deep x 38" (96 cm) high Weight: Freezer: 370 lbs.
3 SECTION 2 INSTALLATION INSTRUCTIONS 2.1 SAFETY PRECAUTIONS Do not attempt to operate the freezer until the safety precautions and operating instructions in this manual are read completely and are thoroughly understood. T ake notice of all warning labels on the freezer (Fig.
4 Fig. 4. Space and Ventilation Requirements 2.2 SHIPMENT AND TRANSIT The freezer has been assembled, operated and in- spected at the factory . Upon arrival at the final destina- tion, the complete freezer must be checked for any damage which may have occurred during transit.
5 Fig. 7. Floor Stand 2.4 FLOOR ST AND INST ALLA TION T o install the E/F131G on the floor stand, follow the steps outlined below . 1. Uncrate the floor stand and place in an upright posi tion. NOTE Detailed instructions are included with each floor stand.
6.
7 3.1 OPERA TOR'S SAFETY PRECAUTIONS SAFE OPERA TION IS NOT AN ACCIDENT ; Observe these rules: A. Know the freezer . Read and understand the Operating Instructions. B. Notice all warning labels on the freezer . C. Wear proper clothing. Avoid loose fitting garments, and remove watches, rings or jewelry which could cause a serious accident.
8 C. PUSH TO FREEZE SWITCH The PUSH TO FREEZE switch is a "snap" switch used to start the freezing cycle. During initial freeze down, the OFF-ON switch is placed in the ON position. Then the PUSH TO FREEZE switch is pressed until the drive motor and compressor come "ON".
9 In general, sanitizing may be conducted as follows: A . Push the mix inlet regulator into hopper with air inlet (long) tube toward the front of the freezer . (Fig. 10). B . Prepare 2 gallons (7.5 liters) of sanitizing solution following manufacturer’s instructions.
10 D. Fill hopper with approximately 3 gallons (1 1.4 liters) o f prechilled (40°F or 4°C) mix. CAUTION DO NOT OVERFILL THE HOPPER. MIX LEVEL MUST NOT BE HIGHER THAN 2 INCHES (5 CM) FROM THE TOP OF THE AIR INLET TUBE ON THE MIX INLET REGULA- TOR. E .
11 3.6 REMOVING MIX FROM THE FREEZER T o remove the mix from the freezer, refer to the following steps: A . Remove the mix inlet regulator from the hopper by pulling straight up (Fig.16). B . Place the OFF-ON rocker switch in the ON position and push the CLEAN switch to rotate the auger .
12 T o disassemble the freezer , refer to the following steps: A . Remove the mix inlet regulator from the hopper by pulling straight up. B . Remove the front door by turning off the circular knobs and then pulling the front door off the studs (Fig.19).
13 C. Using this sanitizing solution and the large barrel brush provided, sanitize the rear of the barrel and drive area by dipping the brush in the sanitizing solution and brushing the rear of the barrel.
14 CAUTION DO NOT PLACE THE MIX INLET REGULA TOR INT O THE HOPPER BEFORE INST ALLING THE AUGER. E . Install the two plastic flights onto rear of the auger and insert part way into freezer barrel. F . Install the third plastic flight, push the auger into the freezer barrel and rotate slowly until the auger engages the drive socket.
15 Once milkstone has formed, it is very difficult to remove. Without using the correct product and procedure, it is nearly impossible to remove a thick layer of milkstone. (NOTE: general-purpose cleaners DO NOT remove milkstone.) This can lead to high bacteria counts and a food safety dilemma.
16 With proper daily use of STERA-SHEEN or it’s equivalent, there is no need for the use of a DELIMER . DO NOT USE BLEACH · BLEACH HAS ABSOLUTELY NO CLEANING PROPERTIES. · BLEACH IS CORROSIVE. It can and will damage components of the machine causing premature wear and metal corrosion.
17 The condenser and condenser filter require periodic cleaning. To clean, refer to the following procedures. W ARNING DISCONNECT FREEZER FROM ELECTRICAL SUPPL Y SOURCE BEFORE SER VICING . 1. Remove the Phillips head screw from the bottom of the right side panel, and then slide the panels down and out.
18.
19 SECTION 4 TROUBLESHOOTING CHARTS M E L B O R P E S U A C E L B I S S O P Y D E M E R s e o d r e z e e r F . n u r t o n . f f o s i r e z e e r f o t r e w o P . 1 . d e p p i r t r o n w o l b f i t i u c r i c r o e s u F . 2 . ) n r u t t o n l l i w r e g u a ( p u - e z e e r F .
20 s e o d t c u d o r P . e s n e p s i d t o n . r e p p o h n i x i m o N . 1 s i e b u t r o t a l u g e r t e l n i x i M . 2 . d e g g u l p d e d e e n r o t a l u g e r t e l n i x i m l a i c e p S . 3 . d e s u g n i e b x i m r o f g n i e b s i r e z e e r f f o y t i c a p a C .
21 ERROR CODE SYSTEM *Refer to Page 19 for Troubleshooting. ** If the Clean switch is operated three times within 10 seconds, this will cause the Push-T o-Freeze light to flash and the clean function will be disabled for 10 minutes. The power switch must remain on or the 10 minute timer will not time out.
22.
23 SECTION 5 REPLACEMENT PARTS 5 .1 HOW TO ORDER PARTS To assure receipt of the proper replacement parts, supply your dealer or distributor with the following information: A . Model number of equipment. B . Serial number of model, stamped on nameplate.
24 Item No. Part No. Description Qt y . 1 2177428 Front Door Only 1 2177072 1.5" Spigot Extension 2177073 2.5" Spigot Extension 2177074 3 " Spigot Extension 624677 C a stle T op O-Ring .
W ARRANTY SOFT SER VE / SHAKE FREEZERS 1. Scope: Stoelting, LLC warrants to the first user (the “Buyer”) that the freezer cylinders, hoppers, compressors, drive motors, speed reducers, auger and a.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Stoelting Futura 131G c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Stoelting Futura 131G - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Stoelting Futura 131G, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Stoelting Futura 131G va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Stoelting Futura 131G, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Stoelting Futura 131G.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Stoelting Futura 131G. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Stoelting Futura 131G ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
