Manuel d'utilisation / d'entretien du produit DP8340R du fabricant Star Micronics
Aller à la page of 52
DOT MA TRIX PRINTER DP8340R SERIES [SERIAL INTERF ACE] USERS MANUAL.
Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
T ABLE OF CONTENTS 1. OUTLINE .............................................................................................. 1 2. UNPACKING AND INSTALLATION ................................................ 2 2-1. Unpacking ............................
8. INTERFACE FOR MODEL DP8340RD (D-SUB 25 PIN CONNECTOR) ......................................................... 30 8-1. Interface Specifications .............................................................. 30 8-2. Interface Circuit ..............
– 1 – 1. OUTLINE The DP8340R series of serial dot matrix printers is for use in ECR, POS, electronic instruments, banking machines and computer peripheral equipment.
– 2 – 2. UNP A CKING AND INST ALLA TION 2-1. Unpacking After opening the box, check if all necessary accessories are included. (A) Printer (B) Power Supply Unit Figure 2-1.
– 3 – 2-2. Installation o f P a per Holders and Re-Roll P r e v ention Guar d Install the Paper Holders in the intermost holes in the rear of the printer.
– 4 – Install the Re-Roll Prevention Wire in the holes of the printer cover. Twisting the Wire as shown in the figure below, will make the installation easier. Figure 2-3. Installation of Re-Roll Prevention 2-3. Handling Notes (1) Install the printer near an easily accessible socket-outlet.
– 5 – 3. P A R T ID E NTIFIC A TION AND NOMENCLA TURE 3-1. Power Supply Unit Figure 3-1. Power Supply Unit DC Power Connector (Output) Shape of AC Power plug will vary according to destinations.
– 6 – 3-2. Printer Figure 3-2. Printer: Front View Figure 3-3. Printer: Rear View.
– 7 – 3-3. Part Functional Description (1) AC Power Plug Connect to an outlet of the specified voltage. (2) DC Power Outlet Supplies DC 12V power to the printer. (3) Printer Cover Protects the printer against dust and reduces noise. (4) POWER Lamp Lights up (green LED) when power is on.
– 8 – 4. INST ALLA TION OF INK RIBBON AND PAPER 4-1. Installation of Ink Ribbon (1) Turn power off, lift the Printer Cover up and remove it. Note: Be careful not to touch the print head immediately after printing, because it can get very hot. Figure 4-1.
– 9 – Figure 4-2. Installation of Ink Ribbon Figure 4-3. Ribbon Spools 4-2. Removal of Ink Ribbon Hold the spool and lift gently, rotating it until the ribbon sags. Push the ribbon detecting lever out, lift the spool until it comes off the shaft. Remove the second spool in a similar manner.
– 10 – 4-3. Paper Insertion 4-3-1. For Roll Paper (1) Cut the Roll Paper end straight and square. Hold the roll so that the paper comes from the bottom. (2) Attach the Roll Paper to the Holders Paper by slipping one side of the roll onto the Hub and pulling the other Hub out to allow the roll to slip in place.
– 11 – 4-3-2. Roll Paper Installation (When using the optional Printer Cover 8340R) When installing roll paper with the optional “Ptinter Cover 8340R”, please use the following procedure. (1) Turn power off, lift the Printer Cover up and remove it.
– 12 – 4-3-3. Validation Option Installation The validation printing requires the optional printer cover 8340R. Refer to item 4-3-2 for the installation. (1) Turn power ON. (2 ) Enter the printer the validation mode. (Refer to the control code “GS” in Chapter 5.
– 13 – 5. CONTROL CODES CODE LF (0A) H FUNCTION Print and line feed instruction OUTLINE The LF code causes the data in the line buffer to be printed, followed by a single line feed. When the line buffer is empty, only the feed takes place. CODE CR (0D) H FUNCTION Print and line feed instruction OUTLINE Same function as of LF code.
– 14 – CODE SI (0F) H FUNCTION Inverted print instruction OUTLINE This function causes the printing to be inverted. This code must be received at the beginning of a line. If this code is received anywhere other than at the beginning of a line, it is disregarded.
– 15 – CODE ESC a n (1B) H (61) H n FUNCTION n-line feed OUTLINE After printing the data in the current line, n lines are fed by this code. The value of n ranges from 1 to 120. CODE ESC C n (1B) H (43) H n FUNCTION Sets page length in lines OUTLINE This code sets the length of a page to n lines.
– 16 – CODE ESC @ (1B) H (40) H FUNCTION Printer initialization OUTLINE All printing conditions except ESC BEL n 1 n 2 , the line buffer and data buffer are set to the power on default condition. CODE ESC BEL n 1 n 2 (1B) H (07) H n 1 n 2 FUNCTION Sets peripheral unit drive pulse duration.
– 17 – CODE FS (1C) H FUNCTION Trigger peripheral unit drive (immediate) OUTLINE Causes a peripheral drive pulse to be generated immediately CODE ENQ (05) H FUNCTION Enquiry OUTLINE When this code is received, the printer outputs status data.
– 18 – CODE ESC M (1B) H (4D) H FUNCTION Select 15 CPI OUTLINE This code causes the printer to print at 15 CPI. The number of columns per line is 44.
– 19 – Character Code List Character Code Function 1 LF (0A)H Print and line feed instruction 2 CR (0D)H Print and line feed instruction (same as LF) 3 SO (0E)H Expanded character instruction 4 DC.
– 20 – 6. GENERAL SPECIFICA TIONS Printing method Serial impact dot matrix printing, 9 wires Number of print columns 29 columns (10CPI), 44 columns (15CPI) Print speed Approx. 2 lines/sec Print direction Bi-directional Line spacing 1/6 inch Paper feed method Friction Feed Paper feed speed Approx.
– 21 – Power supply unit Four supplies available with following ratings Input Output AC 100 – 240 V DC 12.0 V ± 5% 47Hz – 63 Hz 0.8 A Max 2.0 A Paper specification Paper type Ordinary and carbonless copy paper Size Paper width 82.55 ± 0.5mm (3.
– 22 – Figure 6-1. Roll Paper and Print Area Figure 6-2. Material to be validated and One Line Validation Printing.
– 23 – Shape of AC Power plug will vary according to destinations. Figure 6-3. External Dimensions (Printer) Figure 6-4. External Dimensions (Power Supply Unit) 120mm 2.
– 24 – 7. INTERF A CE FOR MODEL DP8340RM (MODULAR JA CK CONNECT OR) 7-1. Interface Specifications (1) Synchronization system Asynchronous (2) Baud rate 150, 300, 600, 1200, 2400, 4800, 9600, BPS (.
– 25 – TYPE ONLY M 7-3-2. DIP-SW2 Switch ON OFF Factory setting 2-1 International character set : ON U.S.A FRANCE 2-2 Always ON ON 2-3(*2) 2-color Ribbon Monochrome Ribbon ON 2-4 CR Invalid CR Valid ON 7-3.
– 26 – 7-4. Connectors and Signals Pin No. Signal Direction Function Name 1 GND — Shield Ground 2 GND — Frame Ground 3 TXD OUT This pin carries data from the printer. (Return channel) 4 RXD IN This pin carries data to the printer. 5 RTS OUT This is SPACE when the printer power is ON.
– 27 – TYPE ONLY M 7-5. Interface Connections For interface connections, refer to the instructions for interface of the host computer. The following gives basic examples.
– 28 – Figure 7-6. Wiring of cable for direct connection between DP8340 and IBM PC serial part 7-6. Peripheral Unit Drive Cir cuit The Control Board of this unit is equipped with a circuit for driving a peripheral unit (Paper Cutter, Take-Up Device, Cash Drawer, etc.
– 29 – TYPE ONLY M Absolute Ratings (Ta = 25˚C) D1 Voltage Breakdown 100V Peak Forward Current 1A Figure 7-8. Cable Connection 7-6-2. Peripheral Drive Circuit Figure 7-9. Drive Circuit Caution: Do not use external power supply with peripheral drive circuit.
– 30 – 8. INTERF A CE FOR MODEL DP8340RD (D-SUB 25 PIN CONNECT OR) 8-1. Interface Specifications (1) Synchronization system Asynchronous (2) Baud rate 150, 300, 600, 1200, 2400, 4800, 9600 BPS (Se.
– 31 – TYPE ONLY D 8-2. Interface Circuit 8-2-1. RS-232C Input (RXD, CTS) Output (DTR, FAULT, TXD, RCH, RTS) Figure 8-1. RS232-C Interface 8-2-2. Current Loop Input (TTY-RXD, TTY-RXDR) Output (TTY-TXD, TTY-TXDR) Note: Resistance should be set so that Current Loop is restricted to the range of 10 ~ 20 mA.
– 32 – 8-3. Setting of the DIP Switches 8-3-1. DIP-SW 1 Switch ON OFF Factory setting 1-1 ON 1-2 Data transfer rate — see below (*1) ON 1-3 ON 1-4 Stop bit 1 Stop bit 2 ON 1-5 DTR MODE (1 BLOCK).
– 33 – TYPE ONLY D 8-4. Jumper Setting The serial interface is set to the RS-232C mode upon shipment from the factory. When using in the 20mA current loop mode, it is necessary to set the jumpers. The jumpers built into the Control Board allow for setting of functions shown in the table.
– 34 – Pin No. Signal Direction Function Name 1 G N D — Frame Ground 2 TXD OUT This pin carries data from the printer. (Return channel) 3 RX D IN This pin carries data to the printer. 4 RT S OU T This is SPACE when the printer power is ON. 5 CTS IN This pin is SPACE when the computer is ready to send data.
– 35 – TYPE ONLY D Figure 8-5. D-Sub 25 Pin Connector 8-6. Interface Connections For interface connections, refer to the instructions for interface of the host computer.
– 36 – 8-7. Peripheral Unit Drive Cir cuit The Control Board of this unit is equipped with a circuit for driving a peripheral unit (Paper Cutter, Take-Up Device, Cash Drawer, etc.) The Control Board Connector (CN3) is used to connect the Peripheral Unit to the Drive Circuit.
– 37 – TYPE ONLY D Figure 8-8. Cable Connection 8-7-2. Peripheral Drive Circuit Absolute Ratings (Ta = 25˚C) D1 Voltage Breakdown 100V Peak Forward Current 1A Drive Output 12V, MAX. 1A Figure 8-9. Drive Circuit Caution: Do not use external power supply with peripheral drive circuit.
– 38 – 9. DA T A STR UCTURE AND CONTROL 9-1. DTR Mode (1 BLOCK) Controls Data Transfer by using DTR line as BUSY FLAG (a) (b) In case of Paper Empty Paper Empty When the paper out detector indicates end of paper, the printer stops printing after a maximum of two lines of printing or paper feed.
– 39 – 9-2. X-ON/X-OFF Mode The printer transmits an X-ON (Control Code; DC1, Hexadecimal Value; 11H,) signal after power is turned on, if there is no printer error being generated. When this signal is received by the host computer, the host computer transmits the data to the printer.
– 40 – Paper Empty When the paper out detector indicates end of paper, the printer stops printing after a maximum of two lines of printing or paper feed.
– 41 – 9-3. STX-ETX Mode The start of the STX-ETX mode should occur with a totally empty print buffer. This can be achieved by sending an ENQ code to the printer and checking the status until the status code indicates an empty buffer. At that point, the STX code is sent by the host computer followed by a data block.
– 42 – STX-ETX Mode Flow Diagram.
– 43 – 10. CHARACTER CODE LIST.
– 44 –.
– 45 – International Character Sets.
– 46 – When printer power is supplied by the user rather than through the accessory power source unit, please be careful of the following points. Note 1: The power supply must be +12V 2A or above. An electrolytic ca- pacitor (C = 4700µF/25V to 6800µF/25V) must be connected across the output of the power supply.
– 47 – VAC 14V C2 100 ~ 200µF/25V VDC 12V ZD1 VZD = 14V (1W) IAC 2 ~ 3A C3 4700 ~ 6800µF/25V C1 6800µF/25V TR1 2SD633 (TOSHIBA) Other parameters may be determined by user.
– 48 – 1999.05.30 Printed in Japan, 80870185 ELECTRONIC PRODUCTS DIVISION STAR MICRONICS CO., LTD. 536 Nanatsushinnya, Shimizu, Shizuoka 424-0066 Japan Tel: 0543-47-0112, Fax: 0543-48-5271 Please access the following URL http://www.star-micronics.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Star Micronics DP8340R c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Star Micronics DP8340R - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Star Micronics DP8340R, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Star Micronics DP8340R va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Star Micronics DP8340R, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Star Micronics DP8340R.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Star Micronics DP8340R. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Star Micronics DP8340R ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
