Manuel d'utilisation / d'entretien du produit ZS-D50 Operating Instructions (primary manual) du fabricant Sony
Aller à la page of 48
3-864-496- 71 (1) 1999 by Sony Corporation Operating Instructions ZS-D50 Personal Audio System.
Introduction 2 Warning To prevent fire or shock hazard, do not expose the player to rain or moisture. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Basic Operations 3 Introduction T able of contents Basic Operations 4 Playing a CD 6 Listening to the radio 8 Playing a tape 10 Recording on a tape CD Player 12 Using the display 13 Locating a specifi.
Basic Operations 4 Playing a CD Basic Operations Connect the supplied AC power cord (see page 34). 1 Press 6 CD OPEN/CLOSE (direct power-on) and place the CD on the CD tray until it clicks into place. 2 Press ^ . (On the remote, press ( on the CD section.
Basic Operations Basic Operations 5 Use these buttons for additional operations Tip Next time you want to listen to a CD, just press ^ . The player turns on automatically and starts playing the CD. To Press adjust the volume VOLUME +, – (VOL +, – on the remote) stop playback p pause playback ^ ( P on the remote) .
Basic Operations 6 Listening to the radio Connect the supplied AC power cord (see page 34). 1 Press RADIO BAND until the band you want appears in the display (direct power-on). 2 Hold down TUNING TIME SET + or – (TUNE + or – on the remote) until the frequency digits begin to change in the display.
Basic Operations Basic Operations 7 Use these buttons for additional operations Tips • If the FM broadcast is noisy, press MODE•MONO/ST ISS (MODE on the remote) until “Mono” appears in the display and the radio will play in monaural. • Next time you want to listen to the radio, just press the RADIO BAND button.
Basic Operations 8 Playing a tape Connect the supplied AC power cord (see page 34). 1 Press 6 PUSH OPEN/CLOSE to open the tape compartment and insert a recorded tape. Use TYPE I (normal), TYPE II (high position) and TYPE IV (metal) tapes. 2 Press 6 PUSH OPEN/CLOSE to close the compartment.
Basic Operations Basic Operations 9 Use these buttons for additional operations To Press adjust the volume VOLUME +, – (VOL +, – on the remote) stop playback p play the reverse side 9 fast-forward.
Basic Operations 10 Recor ding on a tape Connect the supplied AC power cord (see page 34). To record on a MiniDisc or DAT recorder, connect the component (see page 36). 1 Press 6 PUSH OPEN/CLOSE to open the tape compartment, and insert a blank tape. Use TYPE I (normal) tape only.
Basic Operations Basic Operations 11 3 Start recording. To record from the CD player: 1 Press r / P and then ( . (On the remote, while keeping r / P pressed, press TAPE ( .) 2 Press ^ to start playing the CD tracks. To record from the radio: Press r / P and then ( .
The CD Player 12 Using the display You can check information about the CD using the display. The CD Player DISPLAY Checking the total track number and playing time Press DISPLAY in stop mode. Total track number Checking the remaining time Press DISPLAY while playing a CD.
The CD Player The CD Player 13 Locating a specific track You can quickly locate any track using the number buttons. You can also find a specific point in a track while playing a CD. To locate Press a specific track directly number button of the track.
The CD Player 14 Playing tracks repeatedly (Repeat Play) You can play tracks repeatedly in normal, shuffle or program play modes (see pages 16 - 18.). Note When you repeat a single track or all the tracks, make sure neither “SHUF” nor “PGM” is lit in the display.
The CD Player The CD Player 15 Playing a single track (Single Track Play) You can play a single track once, and stop the player automatically. 1 Press p on the CD section. “Cd” appears in the display. 2 Press MODE until “1TRACK” appears in the display.
The CD Player 16 Playing tracks in random or der (Shuffle Play) You can play tracks in random order. 1 Press p on the CD section. “Cd” appears in the display. 2 Press MODE until “SHUF” appears in the display. 3 Press ( on the CD section to start shuffle play.
The CD Player The CD Player 17 Cr eating your own pr ogram (Program Play) While listening to the CD, you can select the track you want and arrange the playing order of up to 20 tracks on a CD. 1 Press p on the CD section. "Cd" appears in the display.
The CD Player 18 To cancel Program Play Press MODE until “PGM” disappears from the display. To check the order of tracks before play Press ENTER•MEMORY CHECK on the player in stop mode until “CHECK” appears in the display. As you press = or + , the track number appears in the programmed order.
The Radio The Radio 19 The Radio Pr esetting radio stations You can store radio stations into the player's memory. You can preset up to 20 radio stations, 10 for each band in any order. RADIO BAND 1 Press RADIO BAND until the band you want appears in the display.
The Radio 20 Playing pr eset radio stations Once you've preset the stations, use the number buttons on the remote or PRESET +/– on the player to tune in your favorite stations. BAND 1 Press BAND to tune in the band you want. 2 Press the number buttons to display the preset number of the station you want.
The Tape Player The Tape Player 21 Finding the beginning of a track The player detects a blank between the tracks, and locates the beginning of the next/following track.
The Tape Player 22 Recor ding the tracks on CD by specifying the tape length There are three options in editorial recording: • Recording all the tracks in the original CD order (EDIT ALL) • Record.
The Tape Player The Tape Player 23 Tip To check the total recording time on the upper side and the reverse side: Press ENTER• MEMORY CHECK before starting recording.
The Tape Player 24 Recording the tracks on CD by specifying the tape length (continued) Recording programed tracks (EDIT PGM) The first half of the programed tracks will be recorded on one side of the tape, and the second half will be recorded on the other side.
The Tape Player The Tape Player 25 Tips • If you made a mistake, press CANCEL. The track programed last will be cleared. Re- program it. • To check the order of tracks, press ENTER• MEMORY CHECK after step 6 until “CHECK” appears in the display.
The Tape Player 26 Recording the tracks on CD by specifying the tape length (continued) Recording a single track (EDIT 1TRACK) EDIT 1TRACK is useful to record the first track of single CD, and to record a track from a number of different CDs. Recorded on the both sides mode “ ” is automatically selected.
The Tape Player The Tape Player 27 4 Press = or + to select the track you want to program. 5 Press r/P and press TAPE ( to record on the upper side or TAPE 9 to record on the reverse side. Recording will start for the selected track. When recording of the track is finished, the CD player and the cassette deck stop.
The Timer 28 Setting the clock “--:--” indication appears in the display until you set the clock. The Timer Tips • The time display system of this player is the 12-hour system: AM12:00 = midnight PM12:00 = noon • When you operate the player on AC power, “:” flashes as long as the clock goes.
The Timer 29 The Timer STANDBY TIMER Before you begin, make sure the t (clock) indication is not lit in the display. If it is lit, press STANDBY. 1 Prepare the music source you want to play. Source Do this C d Insert a CD. RAdIO Tune in a station. TAPE Insert a tape.
The Timer 30 Tip If you made a mistake, press CANCEL. The setting entered last will be cleared. Re-enter it. 4 Set the timer to the hour and the minutes you want the music to go on. 1 Press TUNING TIME SET + or – to set the hour and press ENTER•MEMORY CHECK.
The Timer 31 The Timer Falling asleep to music You can set the player to turn off automatically after 10, 20, 30, 60, 90 and 120 minutes, allowing you to fall asleep while listening to music. SLEEP 1 Play the music source you want. 2 Press SLEEP to display “SLEEP.
The Timer 32 Timer -r ecor ding radio programs You can set timer to record the radio at a certain time. You can also record the sound of the component connected to the LINE IN jack, using the timer. Make sure you have set the clock (see “Setting the clock” on page 28).
The Timer 33 The Timer 5 Set the timer to the hour and the minutes you want to start recording. 1 Press TUNING TIME SET + or – to set the hour and press ENTER•MEMORY CHECK. 2 Press TUNING TIME SET + or – to set the minutes, and press ENTER•MEMORY CHECK.
Setting Up 34 Setting Up Choosing the power sour ces You can use the AC power or batteries as a power source. Use the AC power source whenever you record since recording consumes much power. 14 Battery compartment AC IN 1 Inserting the back-up batteries Insert four size AA (R6) batteries (not supplied) into the battery compartment.
Setting Up 35 Setting Up 3 Inserting batteries into the remote Insert two size AA (R6) batteries (not supplied) Replacing batteries With normal use, the batteries should last for about six months. When the remote no longer operates the player, replace all the batteries with new ones.
Setting Up 36 Connecting optional components You can record a CD on a MiniDisc or enjoy the sound from a VCR, TV or MiniDisc player/recorder through the speakers of this player. Be sure to turn off the power of each component before making connections.
Setting Up 37 Setting Up Tip You can record the sound of the connected component. Insert a blank tape into the tape compartment, and press r / P then TAPE ( (page 11).
Setting Up 38 Listening through the speakers of other audio equipment 1 Connect the LINE OUT jack of this player with the analog line input jack of the amplifier using the audio connecting cable (not supplied) . 2 Turn on the power of this player and the amplifier and start playing sound on this player.
Setting Up 39 Setting Up Selecting the audio emphasis (Sound Mode/MEGA BASS) You can adjust the audio emphasis of the sound you are listening to. SOUND MEGA BASS Selecting the sound characteristic Press SOUND to select the audio emphasis you want. Each time the button is pressed, the display changes.
Additional Information 40 Pr ecautions Additional Information On placement • Do not leave the player in a location near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock. • Do not place the player on an inclined or unstable place.
Additional Information 41 Notes on CDs • Before playing, clean the CD with a cleaning cloth. Wipe the CD from the center out. • Do not use solvents such as benzine, thinner, commercially available cleaners or anti-static spray intended for vinyl LPs.
Additional Information 42 T r oubleshooting General Remedy • Press POWER to turn on the player. • Connect the AC power cord to the AC IN socket and a wall outlet securely. • Make sure the batteries are inserted correctly. • Replace all the batteries with new ones if they are weak.
Additional Information 43 Remedy • If you are listening to an FM program near the TV with an indoor antenna, move the player away from the TV. • Insert the tape properly and close the tape compartment securely. • Replace all the batteries with new ones.
Additional Information 44 Troubleshooting (continued) The player uses a built-in micro computer for its various operations. Due to change in power supply conditions, etc., operation may sometimes become unstable. After trying the above remedies, if the player still does not function properly, unplug the AC power cord and remove all the batteries.
Additional Information 45 Cleaning the tape heads and tape path Wipe the heads, the pinch rollers and the capstans with a cleaning swab slightly moistened with cleaning fluid or alcohol after every 10 hours of operation for optimum playback and recording quality.
Additional Information 46 Specifications AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION With 3-ohm loads, both channel driven from 150 - 8,000 Hz; rated 2 W per channel- minimum RMS power, with no more than 10 % total harmonic distortion in AC operation.
Additional Information 47 Index A Audio emphasis 39 B Batteries for memory 34 for player 35 for remote 35 C CD Player 12 Cleaning cabinet 45 CD 41 tape heads and path 45 Connecting AC power cord 34 op.
Additional Information 48 Sony Corporation Printed in China.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Sony ZS-D50 Operating Instructions (primary manual) c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Sony ZS-D50 Operating Instructions (primary manual) - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Sony ZS-D50 Operating Instructions (primary manual), vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Sony ZS-D50 Operating Instructions (primary manual) va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Sony ZS-D50 Operating Instructions (primary manual), mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Sony ZS-D50 Operating Instructions (primary manual).
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Sony ZS-D50 Operating Instructions (primary manual). Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Sony ZS-D50 Operating Instructions (primary manual) ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
