Manuel d'utilisation / d'entretien du produit MZ-NF810 du fabricant Sony
Aller à la page of 68
SERVICE MANUAL POR T ABLE MINIDISC RECORDER US Model Canadian Model MZ-NF810CK AEP Model UK Model E Model A ustr alian Model Chinese Model T our ist Model MZ-NF810 SPECIFICA TIONS MZ-NF810/NF810CK US and f oreign patents licensed from Dolby Laboratories.
2 MZ-NF810/NF810CK Radio Frequenc y range USA model: FM: 87.5 - 108.0 MHz AM: 530 - 1,710 kHz (10 kHz step) 531 - 1,710 kHz (9 kHz step) TV : 2 - 13 C H WEA T HER : 1 - 7 CH Canad ian m odel: FM: 87.
3 MZ-NF810/NF810CK T ABLE OF CONTENTS 1. SER VICING NO TES ................................................ 4 2. GENERAL ................................................................... 5 3. DISASSEMBL Y 3-1. Disassembly Flow ......................
4 MZ-NF810/NF810CK NO TES ON HANDLING THE OPTICAL PICK-UP BLOCK OR B ASE UNIT T he laser diode in the optical pick-up block may suf fer electro- static break-do wn because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body .
5 MZ-NF810/NF810CK SECTION 2 GENERAL This section is e xtracted from instruction manual. 14 Looking at controls The recor der A x • CANCEL/CHG button B Display window C Batt ery co mpartment D GROUP.
6 MZ-NF810/NF810CK SECTION 3 DISASSEMBL Y • This set can be disassembled in the order sho wn below . 3-1. Disassembl y Flow CASE (LOWER) P ANEL (UPPER) SECTION In order to remov e mechanism deck (MT -MZN710-177) , please remov e MAIN board and upper panel section.
7 MZ-NF810/NF810CK Note: Follo w the disassembly procedure in the numerical order given. 3-2. Case (Lower) 3-3. MAIN Board, Battery Case 4 two screws (M1.4) 6 two screws (M1.4) 5 screw (M1.4) 3 Remove the battery case lid. battery lid 1 Open the battery case lid.
8 MZ-NF810/NF810CK 3-5. LCD Module, Panel Upper Bloc k 3-4. P anel (Upper) Section 1 six screws (1.7 × 2.5) 2 LCD module 4 spring (rec) Note: On installation, adjust the position of both switch and knob (hold), knob (t mark). knob (hold) button (t mark) 3 button (play ) switch 5 upper panel block 3 two screws (M1.
9 MZ-NF810/NF810CK 3-6. Mechanism Deck (MT -MZN710-177) 1 two step screws (MD) 4 set chassis assy 3 mechanism deck (MT-MZN710-177) 2.
10 MZ-NF810/NF810CK 3-7. OP Service Assy (LCX-5R) 4 rack spring 3 screw (M1.4) 1 washer (0.8-2.5) 2 gear (SA) 5 screw (M1.4) 6 thrust detent spring 8 Pull off lead screw. 7 over write head section OP service assy (LCX-5R) 9 Opening the over write head toward the direction A , remove the OP service assy (LCX-5R) toward the direction B .
11 MZ-NF810/NF810CK 3-9. DC Motor (Sled) (M602) 3-8. Holder Assy 4 holder ass y 3 boss 3 boss 1 convex portion 2 Open the holder assy. 2 washer (0.8-2.5) 5 DC motor (sled) (M602) 4 two screws (M1.4) 3 gear (SA) 1 Remove six solders of the motor flexible board.
12 MZ-NF810/NF810CK 3-10. DC Motor (Over Write Head Up/Down) (M603), DC SSM18B Motor (Spindle) (M601) 9 DC SSM18B motor (spindle) (M601) 8 three tapping screws 2 tapping screw 3 motor cover 6 gear (HA) 4 gear (HB) 5 gear (HC) DC motor (over write head up/down) (M603) 3.
13 MZ-NF810/NF810CK Operation in Setting the T est Mode •W hen the test mode becomes acti ve, first the display check mode is selected. • Other mode can be selected from the display check mode. •W hen the test mode is set, the LCD repeats the following dis- play .
14 MZ-NF810/NF810CK Configuration of T est Mode Manual Mode Mode to adjust or check the operation of the set by function. Normally , the adjustment in this mode is not executed.
15 MZ-NF810/NF810CK Self-Diagnosis Result Displa y Mode This set uses the self-diagnostic function system in which if an error occurred during the recording or playing, the mechanism control block and the po wer supply contr ol block in the microcomputer detect it and record its cause as history in the non volatile memory .
16 MZ-NF810/NF810CK • Description of indication history Histor y code number Description 1T he first error N The last error N1 One error before the last. N2 T wo errors before the last. R_ T otal recording time Reset the Err or Display Code After servicing, reset the error display code.
17 MZ-NF810/NF810CK Ke y Chec k Mode T his set can check if the set and remote commander function nor - mally . • Setting method of key chec k mode 1. Set the test mode (see page 13). 2. Pressing the [T MARK] key or [DISPLAY] key on the remote commander for several seconds (about 3 seconds) activates the ke y check mode.
18 MZ-NF810/NF810CK Outline • In this set, automatic adjustment of CD and MO can be per- formed by entering the test mode. Howe ver , before starting automatic adjustment, the memory clear , po wer supply adjustment, and laser po wer check must be performed in the manual mode.
19 MZ-NF810/NF810CK • Adjustment Method of VC2_HIGH (item number: 744) 1. Connect a digital voltmeter to the TP1905 (VCOUT) on the MAIN board, and adjust [VOL +] ke y (voltage up) or [VOL - - ] ke y (volta ge down) so that the v oltage becomes 2.55 ± 0.
20 MZ-NF810/NF810CK • Adjustment Method of REG3_LO W2 (item number: 748) 1. Connect a digital voltmeter to the TP1907 (REGO3) on the MAIN board, and adjust [VOL +] key (voltage up) or [VOL - - ] ke y (voltag e down) so that the v oltage becomes 1.25 ± 0.
21 MZ-NF810/NF810CK • Adjustment Method of CHGV_LO W (item number: 755) Note: Remove the r echargeable battery . 1. Connect a digital voltmeter to the B A TT+ on the MAIN board, and adjust [VOL +] ke y (voltage up) or [VOL - - ] ke y (v oltage do wn) so that the voltage becomes 1.
22 MZ-NF810/NF810CK Adjustment/checking and Connection Location: IC951 IC671 IC851 IC801 IC501 IC301 IC601 IC901 IC361 TP1715 TP1717 TP1524 TP1519 C533 TP1909 TP1930 TP1892 TP1356 1 6 7 13 18 19 24 12.
23 MZ-NF810/NF810CK Po wer Supply Adjustment A uto Item Feed Note: This mode is available to perform the temperature correction and power supply adjustment without entering the manual mode. • Setting method of power supply adjustment auto item feed mode.
24 MZ-NF810/NF810CK VOL+ key . key on the remote commander > key on the remote commander x key Overall adjustment mode (Title display) Continuing overall adjustment [END SEARCH] key [P MODE] key on.
25 MZ-NF810/NF810CK • Adjustment Method of CD and MO Overall Adjustment Mode 1. Set the test mode (see page 13). 2. Press the key or press [VOL - - ] key to activate the overall adjustment mode. 3. Insert CD disc in the set, and press the key to set the CD over all adjustment mode.
26 MZ-NF810/NF810CK Item No . Description 434 TWPP gain adjustment 431 TWPP offset adjustment 1 432 TE offset adjustment 2 449 TWPP OP offset adjustment 410 READ → WRITE selection 411 TWPP offset adjustment 1 412 TE offset adjustment 2 418 TWPP OP offset adjustment 490 HCL V LCL V selection process 450 HEAD DO WN .
27 MZ-NF810/NF810CK Remuse Clear Perform the Resume clear when all adjustments completed. • Resume Clear Setting Method 1. Select the manual mode of the test mode, and set item number 043 (see page 14). 2. Press the X key . 3. Press the x CANCEL/CHG key to return to the test mode (dis- play check mode).
28 MZ-NF810/NF810CK Rewriting the P atch Data at Replacement of Main Boar d (IC851) This set requires the patch data in the nonvolatile memory (IC851) to be rewritten using the application, when the MAIN board was replaced. Caution: T he application that meets the microcomputer version in this set must be used when re writing the patch data.
29 MZ-NF810/NF810CK 5. Confirm that the model and version indicated on the title bar coincide with the codes displayed in the Device Name block and the Ve r sion block in the window .
30 MZ-NF810/NF810CK • Confirmation of contents of the patch data rewrited 1. Click the [READ] button to confirm the contents of the patch data rewrited. 2. The application reads out the front and reverse patch areas and displays the results in the edit box.
31 MZ-NF810/NF810CK • Disconnecting the USB cable Disconnect the USB cable as the following procedure after rewriting the patch data and confirmation. Note : W hen the follo wing procedure is not completed but USB cable is extracted, the application does not recognize the set a t excha nging of the set.
32 MZ-NF810/NF810CK Rewriting the NV v alues Caution: T he application that meets the microcomputer version in this set must be used w hen rewriting the NV values. Re writing the NV values using the application not suitable for the microcomputer version could cause the set to malfunction.
33 MZ-NF810/NF810CK 5. Confirm that the model and version indicated on the title bar coincide with the codes displayed in the Device Name block and the Ve r sion block in the window .
34 MZ-NF810/NF810CK 7. The operation will terminate with “Compere OK” given to all areas. If “Compere NG” is giv en to any area, the non volatile memory will be faulty .
35 MZ-NF810/NF810CK 9. Confirm that the windo w becomes as shown belo w where the [Write + V erify] button is inacti ve. 10. Disconnect the USB cable from the personal computer and the set.
36 MZ-NF810/NF810CK MEMO.
MZ-NF810/NF810CK 37 37 SECTION 6 DIA GRAMS 6-1. Bloc k Diagram OPTICAL PICK-UP BLOCK LDA FOCUS COIL TRACKING COIL MOTOR/COIL DRIVE IC701 FO2 30 RO2 32 13 11 TRK+ TRK- FCS+ FCS- 28 FI2 RF AMP IC501 11 .
MZ-NF810/NF810CK 38 38 Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except f or electrolytics and tantalums. • All resistors are in Ω and 1 / 4 W or less unless otherwise specified.
MZ-NF810/NF810CK 39 39 6-3. Printed Wiring Board – MAIN Boar d (Side A) – :Uses unleaded solder . • Semiconductor Location IC701 IC651 IC990 MAIN BOARD (SIDE A) LCX-5R J302(2/2) (OPTICAL) OPTICA.
MZ-NF810/NF810CK 40 40 6-4. Printed Wiring Board – MAIN Boar d (Side B) – :Uses unleaded solder . • Semiconductor Location IC951 IC671 IC851 IC801 IC501 IC301 IC601 IC901 IC361 1 16 49 64 33 48 .
MZ-NF810/NF810CK 41 41 6-5. Schematic Diagram – MAIN Boar d (1/4) – • See page 38 for W a vef or ms. • See page 47 and 49 for IC Bloc k Diagr ams.
MZ-NF810/NF810CK 42 42 6-6. Schematic Diagram – MAIN Boar d (2/4) – • See page 38 for W av eforms. • See page 45 for IC Bloc k Diagrams . C366 C211 Q361 C362 D302 C315 C 323 C206 C207 C106 C10.
MZ-NF810/NF810CK 43 43 6-7. Schematic Diagram – MAIN Boar d (3/4) – • See page 38 for W av ef or ms. • See page 50 f or IC Block Diagrams . C834 S801 C819 S805 S803 S804 C827 C835 C826 C825 C8.
MZ-NF810/NF810CK 44 44 6-8. Schematic Diagram – MAIN Boar d (4/4) – • See page 38 for W av eforms. • See page 46 and 48 for IC Bloc k Diagrams.
45 MZ-NF810/NF810CK • IC Block Dia grams IC301 AK5356VN-N V REF MT SW BST SW BEEP 19 20 21 22 23 24 18 17 16 15 14 13 PW SW 12 11 10 8 7 BST1 9 BST2 6 5 4 3 2 1 BST AGC PW B PW A ADD TC MT VCC INR I.
46 MZ-NF810/NF810CK IC501 SN761058ZQLR 1 IX 2 PS 3 EQ 4 A GND 5 OFC-C1 6 OFC-C2 7 VREF10 8 VC 9 RFO 10 VREF09 11 AVCC2 AVCC2 AVCC AVCC2 12 PD-NI 13 PD-I 14 PD-O D-C A-C SCF1(NC) SMON ADIP-IN SCF2(NC) .
47 MZ-NF810/NF810CK IC601 XPC18A22AEPR2 VG VG3 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 54 55 56 1 53 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 24 23 25 26 .
48 MZ-NF810/NF810CK IC701 SC111258EPR2 14 13 56 55 CPWI2 CPVI2 CPUI2 COM2 RI2 FI2 UI1 PWM1 CPUO1 CPWO1 VG VC 36 37 38 39 40 41 52 51 50 49 48 47 46 45 44 43 42 23 24 25 12 11 10 9 8 7 6 5 4 3 2 1 GND1.
49 MZ-NF810/NF810CK IC951 SC901582EPR2 1 2 3 4 5 6 7 8 9 10 11 12 18 19 17 16 15 14 24 23 22 21 20 19 DELAY VCR TIME DIVIDER OSC LOGIC SIGNAL RECEIVER VOLTAGE REFERENCE LOGIC SIGNAL RECEIVER VO VREF N.
50 MZ-NF810/NF810CK 6-9. IC Pin Function Description • IC801 CXD2680-203GA (SYSTEM CONTR OLLER, DIGIT AL SIGNAL PR OCESSOR) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 .
51 MZ-NF810/NF810CK Pin No. 51 52 53 54 55 56 57 58 59 60 61 62, 63 64 to 66 67 68 69 70 71 72 73 74 75 76 77 78 to 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109.
52 MZ-NF810/NF810CK Pin No. 111 112 113 114, 115 116 117 118 119, 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139, 140 141 142 143 144 145 146 147 148 149 150 151 152 1.
53 MZ-NF810/NF810CK Pin No. 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195, 196 197 198 199 200 201 202 to 204 205, 206 207 208.
54 MZ-NF810/NF810CK Pin No. 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 .
55 MZ-NF810/NF810CK Pin No. 299 300 301, 302 303, 304 305 306 to 312 I/O — — — — — — Pin Name FVDD0 FVSS0 DVDD5, 6 DRAMVDD3, 4 MSAK NC Description Power supply terminal (for the built-in f.
56 MZ-NF810/NF810CK 7-1. Case Section SECTION 7 EXPLODED VIEWS NO TE: • -XX and -X mean standardized parts, so they may have some dif ference from the original one.
57 MZ-NF810/NF810CK 7-2. Chassis Section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark MD mechanism deck (MT -MZN710-177) not supplied MAIN board section 51 57 58 52 59 53 .
58 MZ-NF810/NF810CK 7-3. MAIN Board Section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 101 3-245-891-01 TERMINAL (–), BA TTERY 102 3-245-890-01 CASE, BA TTERY 103 X-3382-584-1 TERMINAL (+) ASSY , BATTER Y 104 3-234-449-19 SCREW (M1.
59 MZ-NF810/NF810CK 7-4. Mechanism Deck Section-1 (MT -MZN710-177) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark mechanism deck section-2 A A 301 not supplied 311 310 308 309 307 305 304 303 302 306 301 X-3381-219-1 HOLDER ASSY 302 3-224-779-02 SPRING, THRUST DETENT 303 3-225-996-01 SCREW (M1.
60 MZ-NF810/NF810CK 7-5. Mechanism Dec k Section-2 (MT -MZN710-177) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark M601 not supplied M603 351 351 364 363 362 361 360 359 352.
61 MZ-NF810/NF810CK SECTION 8 ELECTRICAL P ARTS LIST Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark NO TE: • Due to standardization, replacements in the parts list may be dif ferent from the parts speci- fied in the diagrams or the components used on the set.
62 MZ-NF810/NF810CK Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C527 1-164-941-11 CERAMIC CHIP 0.0047uF 10.00% 16V C533 1-164-943-11 CERAMIC CHIP 0.01uF 10.00% 16V C534 1-164-941-11 CERAMIC CHIP 0.0047uF 10.00% 16V C535 1-125-837-91 CERAMIC CHIP 1uF 10% 6.
63 MZ-NF810/NF810CK Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark CN701 1-573-350-11 CONNECTOR, FFC/FPC 10P CN871 1-573-355-11 CONNECTOR, FFC/FPC 15P < DIODE > D101 8-719-056-72 DIODE 02DZ2.4-Z(TPH3) D201 8-719-056-72 DIODE 02DZ2.
64 MZ-NF810/NF810CK Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < RESISTOR > R101 1-208-927-11 MET AL CHIP 47K 0.5% 1/16W R102 1-208-715-11 MET AL CHIP 22K 0.5% 1/16W R103 1-208-715-11 MET AL CHIP 22K 0.5% 1/16W R104 1-208-707-11 MET AL CHIP 10K 0.
65 MZ-NF810/NF810CK Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark MAIN R836 1-218-985-11 RES-CHIP 470K 5% 1/16W R837 1-218-973-11 RES-CHIP 47K 5% 1/16W R838 1-218-957-11 RES-CHIP 2.
66 MZ-NF810/NF810CK Part No. Description Remark 1-794-451-11 CONNECTOR, LIGHT (US,CND,3CED,4CED,UK,TW ,AUS,JE) 1-794-451-51 CONNECTOR, LIGHT (E,HK,CH) 1-823-519-11 CORD, CONNECTION 3-008-521-01 CASE, .
67 MZ-NF810/NF810CK MEMO.
MZ-NF810/NF810CK REVISION HIST OR Y Clicking the ver sion allows you to jump to the re vised page. Also, clicking the v ersion at the upper right on the revised page allo ws you to jump to the next re vised page. Ve r. Date Description of Revision 1.0 2003.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Sony MZ-NF810 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Sony MZ-NF810 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Sony MZ-NF810, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Sony MZ-NF810 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Sony MZ-NF810, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Sony MZ-NF810.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Sony MZ-NF810. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Sony MZ-NF810 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
