Manuel d'utilisation / d'entretien du produit ZF2501KH, ZF5201M, ZF6101M du fabricant Snapper
Aller à la page of 32
1 Safety Instructions & Operator’s Manual for OUT FRONT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 1 POWER UNIT MODELS ZF2501KH MOWER UNIT MODELS ZF5201M ZF6101M MODEL NUMB ER EXPLA NA TION Z F 25 .
2 IMPORTA NT SA FETY INSTRUCTIONS WARNING: This pow erful cutting machin e is capable of ampu tating han ds and feet an d can t hrow object s that can cause injury and damag e! Failure to comply with t he follow ing SAFETY instruct ions could resu lt in serious injury or death to the operator or other persons.
3 IMPORTA NT SA FETY INSTRUCTIONS PREPA RA TION (Continued From Pre v ious Page) 4. Handle fuel w ith extra care. Fu els are flammable and vap ors are explosive. Use only an approv ed fuel contain er. DO NOT remove fuel cap or add fuel with engine running.
4 IMPORTA NT SA FETY INSTRUCTIONS MA INTENA NCE (Continued From Pre v ious Page) 7. Disconnect battery before pe rforming maintenance or service. Crankin g engine co uld cause injury. Disconnect n egative (b lack) cable from battery first and positiv e (red) cable last .
5 TABLE OF CONTENTS IMPORTA NT SAFETY INSTRUCTIONS................................................ 2-4 TA BLE OF CONTENTS .............................................................................5 SECTION 1 – FA MILIA RIZA TION .................
6 Section 1 - FA MILIA RIZA TION FIGURE 1.1 1. 1 INTRODUCT ION This manual has been prepar ed for the oper ator’s of the SNAPPER OUT FRONT Z-RIDER. Its purpose, aside from rec omm ending s tandard operating procedur es and routine servic e requirem ents, is to prom ote SAFET Y through the use of accepted operating practices .
7 Section 2 – SA FETY MESSA GES A ND SYMBOLS ENGINE SPEED A ND CHOKE CONTROLS RA BBIT “FA ST” TURTLE “SLOW” CHOKE “ON” CHOKE “OFF”.
8 Section 2 – SA FETY MESSA GES A ND SYMBOLS HOUR ME TE R LIGHT SWITCH BLA DE KEY SW I TCH MOTION CONTROL MULTI -DIRECTIONAL “STOP” “RUN ” “STA RT” ENGA GE “ON” DISENGAGE “OFF” .
9 Section 2 – SA FETY MESSA GES A ND SYMBOLS DA NGER! ROTA TING BLA DES KEEP CHILDREN A ND OTHERS O UT OF MO WING AREA DA NGER! ROTA TING BLA DES.
10 Section 3 - OPERA TING INSTRUCTIONS 3.1 PRE-START CHECK LIST Make the f ollowing check s and per form the servic e required bef ore each star t-up. 3.1.1. Check tires and add or r elease air as needed to bring press ure in drive tires to: 12 psi ( Turf T ype Tires ), 5 psi (All T errain T y pe Tires ) and 25 psi in rear caster tire.
11 Section 3 - OPERA TING INSTRUCTIONS 3.2 STARTING & STOPPING – ENGINE, BLA DES & PA RKING BRA KE This mac hine is equipped with dual hydrostatic wheel drive transm issions . Each transm iss ion is controlled by a single motion control lever or joystick.
12 Section 3 - OPERA TING INSTRUCTIONS 3.2. STOPPING ENGINE 3.2.1. ENGINE 1. Stop engine by tur ning key to the “OFF” position. Move engine speed c ontrol to turtle “SLOW ” pos ition and key to “ST OP” position. See Figure 3.6. WA RNING DO NOT leave mac hine with engine running.
13 Section 3 - OPERA TING INSTRUCTIONS 3.3 OPERATION – MOT ION CONTROL 3.3.1 DRIVING MACHINE IMPO RTANT: The joystick lever has to be manually mo ved to propel mac hine. Alway s return the jo y stick with hand assistance to the neutral position to s top ma chine.
14 Section 4 – MA INTENA NCE 4.1 INTRODUCT ION To retain the quality of the SNAPPER Out Fr ont Z- Rider, use genuine SNAPPER replacem ent parts only .
15 Section 4 – MA INTENA NCE 4.2.3. CHECK M OW ER DRIVE BELT 1. Drive Belt Cover Remov al a. Lower deck to lowest s etting. b. Remove f our k nobs that s ecure the deck cover. See Figure 4.3. c. Remove cover to gain acc es s to deck belt. FIGURE 4.3 2.
16 Section 4 - MA INT ENA NCE 4.3.3. RIDING M OWER - LUBRICATION 1. F ront & Rear Wh eel Bearings Lubricate with Kendall NLGI No. 2 lithium grease or equivalent, fr om a gr ease gun. See Figure 4.5. FIGURE 4.5 2. Transaxle Check the level of f luid in both of the f luid reservoir s.
17 Section 4 – MA INTENA NCE 4.5 A NNUA LLY (END OF EA CH SEA SON) (Continued from previous P age) 4.5.2. F UEL FILT ER Service f uel filter as instructed below. T urn k ey to “OFF ” position. Engine MUST be stopped and MUST be cold befor e rem oving filter.
18 Section 5 - A DJUSTMENTS & REPA IR DA NGER Exercise EXTREM E CA UTION w hen making this adjustment, due to clos e proximity of moving parts. 5.1 NEUTRAL POSITIO N A DJUSTM ENTS The joystick contr ols the movem ent and stopping of the machine. Move the joystick to the center or neutral position to st op m achine.
19 Section 5 - A DJUSTMENTS & REPA IR 5.2.1. MO WER DECK A DJUSTMENT (Continued) 7. Tur n ball joint in or out until ball joint anchor hole aligns with m ounting hole. Reinstall bolt and tighten sec urely. Use sam e procedure on other caster wheel.
20 Section 5 - A DJUSTMENTS & REPA IR 5.5 M OWER BLADE REPA IR/REPLACEMENT 5.5.1. BL A D E WEA R LIM ITS 1. Inspect blade f requently for signs of excess ive wear or damage. See F igure 5.5. FIGURE 5.5 WA RNING DO NOT use a cuttin g blade that show s signs of excessive wear or damage.
21 Section 5 - A DJUSTMENTS & REPA IR 5.6.2. ENGINE BELT REPLACEMENT 1. Route belt around blade pulleys and idler pulley in sam e the position as old belt was rem oved. It may be necessar y to use a pry bar to pull idler pulley back to install belt.
22 Section 5 - A DJUSTMENTS & REPA IR 5.7.4. BATTERY TEST ING There ar e two ty pes of battery tests: Unloaded and Loaded. The unloaded tes t is the procedure that will be disc us sed. It’s the sim plest and m ost c omm only used. An unloaded test is made on a battery wi thout discharging c urrent.
23 Section 5 - A DJUSTMENTS & REPA IR 5.8 M OWER SPINDLES (Field Serv iceable Spindles) BEA RING REPLACEMENT In the event that a spindle bearing requir es replacem ent, the SNAPPER Field Servic eable Spindles have been designed so that no s pecial tools or pres ses are r equired.
24 TROUBLESHOOTING PROBLEM PROBA BLE CAUSE CORRECTIVE ACTION Starter Will Not Crank 1. Battery dead. 1. Service battery. Engine 2. Blown fuse. 2. Replace fuse. 3. Electrical connections loose or corroded. 3. C l ean and check connections for good contact.
25 TROUBLESHOOTING PROBLEM PROBA BLE CAUSE CORRECTIVE ACTION Tractor Will Not Move 1. Joystick in the neutral “N” position. 1. Place joystick in desired speed position. Loss Of Traction 2. R o ll r e le a s e lever is in “R O LL ” p os i t i o n.
26 SERVICE SCHEDULE ITEM SERVICE PERFO RMED REF. EA CH USE 5 HRS 25 HRS 50 HRS 100 HRS EA CH SEA SON Engine Oil Check Oil Level Page 10 X Initial Oil Change Page 14 X Periodic Oil Change Page 14-15 X*.
27 2 YEAR LIMITED WA RRANTY For two (2) years from purc hase date for the or iginal purchaser 's use, SNA PPER , through any authorized SNA PPER dealer will replace, f ree of char ge (except f or.
28 PRIMA RY MA INTENA NCE.
29 PRIMA RY MA INTENA NCE.
30 PRIMA RY MA INTENA NCE.
31 PRIMA RY MA INTENA NCE.
32 Safety Instructions & Operator’s Manual for OUT FRONT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 1 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactur ed. The labels on those engine s contain very important emissions information and critic al safety warnings.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Snapper ZF2501KH, ZF5201M, ZF6101M c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Snapper ZF2501KH, ZF5201M, ZF6101M - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Snapper ZF2501KH, ZF5201M, ZF6101M, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Snapper ZF2501KH, ZF5201M, ZF6101M va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Snapper ZF2501KH, ZF5201M, ZF6101M, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Snapper ZF2501KH, ZF5201M, ZF6101M.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Snapper ZF2501KH, ZF5201M, ZF6101M. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Snapper ZF2501KH, ZF5201M, ZF6101M ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
