Manuel d'utilisation / d'entretien du produit C282 du fabricant Shindaiwa
Aller à la page of 28
C282 BR USHCUTTER SHIND AIWA O WNER’S/OPERA T OR’S MANU AL Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself with the contents.
2 The Shindaiwa 282 series is designed and built to deliver superior per for mance and reliability without compromise to quality , comfor t, safety or durability . Shindaiwa engines represent the leading edge of high-per for mance engine technology , delivering exceptionally high power with remarkably low displacement and weight.
3 W or k Saf el y T rimmers and br ushcutters operate at ver y high speeds and can do serious damage or injur y if they ar e misused or abused. Never allow a person with- out training or instruction to operate this unit! Stay Aler t Y ou must be physically and mentally fit to operate this unit safely .
4 Be Aware of the Working Environment Avoid long-term operation in very hot or very cold weather . Make sure bystanders or observers outside the 15 meter (50 feet) “danger zone” wear eye protection. Be extremely careful of slippery terrain, especially during rainy weather .
5 Product Description Specications Model Name C282 Engine Type 2-cycle catalyst Displacement 28.9 cc / 1.8 cu. in. Bore and Stroke 30 x 35 mm / 1.2 x 1.4 in Dr y W eight (less attachment) 7.0 kg / 15.5 lb. Dimensions (L x H x W) mm 1783 x 345 x 314 mm / 70.
6 Outer T ube Lower Cap Retaining Screws Handlebar Strap Lower cap Hanger Mounting the brushcutter handlebar Handle Positioning Label Assembly Prior to Assembly Before assembling, make sure you have all the components required for a com- plete unit and inspect unit and compo- nents for any damage.
7 4-6 mm Adjust throttle lev er fr ee play The thro ttle lever free play shou ld be approximately 4-6 mm. Make sure that the throttle lever operates smoothly without binding. If it becomes necessar y to adjust the lever free play , follow the procedures and illustrations that follow .
8 Assembly (continued) NOTE: This unit is shipped with Holder A, Holder B, shaft bolt, and bolt guard installed. The shaft bolt is a LEFT - HAND thread.
9 Assembly (continued) Hex Wrench Tighten the assembly (blade not shown for clarity) CA UTION! Install the blade so its printed sur- face is visible to the operator when the brushcutter is in the normal operating position. The unit should now be completely assembled and ready for use with a blade.
10 Handling Fuel DANGER Fuel is VERY ammable. Use extreme care when mixing, storing or handling or serious personal injury may result. • Use an approved fuel container . • DO NOT smoke near fuel. • DO NOT allow ames or sparks near fuel. • Fuel tanks/cans may be under pressure.
11 Star ting the Engine IMPORT ANT! Engine ignition is controlled by a two position switch mounted on the throttle housing labeled, “I” for ON or STAR T and “O” for OFF or STOP . WARNING! Never start the engine from the operating position. Slide the ignition switch to the “I” 1.
12 NEVER operate the unit with the cut - ting attachment shield or other protec - tive devices removed! Use only authorized Shindaiwa par ts and accessories with your Shindaiwa trimmer . Do not make modifications to this unit without written approval from Shindaiwa, Inc.
13 Y our Shindaiwa unit may be equipped with one of several Shindaiwa trimmer head models, each with features for spe - cific applications and/or operational requirements. Cutting gr ass with a trimmer head NOTE: For proper operation, always refer to the instructions accompanying the trim- mer head being used.
14 D O N O T C U T Blade T hr ust “Blade thr ust” is a sudden sideways or backward motion of the br ushcutter . Such motion may occur when the blade jams or catches on an object such as a sapling tree or tree stump. BE CON- STANTL Y ALER T FOR BLADE THRUST AND GUARD AGAINST ITS EFFECTS! The blade rotates counter-clockwise.
15 Mufer This unit must never be operated with a faulty or missing spark ar r ester or muf fler . Make sure the muf fler is well secured and in good condition. A wor n or damaged muf fler is a fire hazar d and may also cause hearing loss. Spar k Plug Keep the spark plug and wire connec- tions tight and clean.
16 Air Filter Element Unscrew Fastener Remove and clean or replace the element 10-hour maintenance CA UTION! Do not operate the unit if the air cleaner or lter is damaged, or if the lter is wet or water soaked. Per for m more frequently in dusty or dir ty conditions.
17 Maintenance (continued) Fuel lter element Hooked wire Fuel lter maintenance Remove and replace the fuel filter element. Before reinstalling the new filter element, inspect the condition of all the fuel sys - tem components (fuel pick-up line, fuel retur n line, tank vent line, tank vent, fuel cap and fuel tank).
18 Maintenance (continued) WARNING! Sharpen only the cutting teeth of a blade. DO NOT alter the contour of the blade in any way . WARNING! Wear protective gloves when handling or performing maintenance on the blade. When the cutting edges of the blade become dull, they can be resharpened with a few strokes of a file.
19 IMPORT ANT! Stored fuel ages. Do not mix more fuel than you expect to use in thir ty (30) days, ninety (90) days when a fuel stabilizer is added. Idle adjustment screw Adjusting engine idle Adjusting Engine Idle The engine must retur n to idle speed whenever the throttle lever is released.
20 T roubleshooting Guide V aporlock. Engine hot/heat soaked. Low fuel quality . Let cool completely and restar t. Refi ll with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO FD classifi ed oils at 50:1 gasoline/oil ratio.
21 ADDITIONAL PROBLEMS Poor acceleration. Clogged air fi lter . Clogged fuel fi lter . Lean fuel/air mixture. Idle speed set too low . Ignition switch tur ned of f. Fuel tank empty . W ater in the fuel. Clogged fuel fi lter . Shor ted spark plug or loose terminal.
22 ADDITIONAL PROBLEMS Poor acceleration. Clogged air fi lter . Clogged fuel fi lter . Lean fuel/air mixture. Idle speed set too low . Ignition switch tur ned of f. Fuel tank empty . W ater in the fuel. Clogged fuel fi lter . Shor ted spark plug or loose terminal.
23 SHINDAIW A LIMITED W ARRANTY ST A TEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO, INC’S RESPONSIBILITY ECHO Incorporated’s (ECHO, INC.) Limited W arranty , provides to the original purchaser that this Shindaiwa product is free from defects in material and workmanship.
24 PURCHASED REP AIR P ARTS AND ACCESSORIES • 90-day all applications A TTENTION ENGINE POWERED PRODUCT OWNERS This Shindaiwa engine powered product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior performance.
25 PURCHASED REP AIR P ARTS AND ACCESSORIES • 90-day all applications A TTENTION ENGINE POWERED PRODUCT OWNERS This Shindaiwa engine powered product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior performance.
26 NO TES.
27 NO TES.
ECHO Incorporated. 400 Oakwood Road Lake Zurich, IL 60047-1564 U.S.A. T elephone: 1-877-986-7783 Fax: 1-847-540-8416 www .shindaiwa.com Y amabiko Corporation 7-2 Suehirocho 1-Chome, Ohme, T okyo, 198-.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Shindaiwa C282 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Shindaiwa C282 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Shindaiwa C282, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Shindaiwa C282 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Shindaiwa C282, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Shindaiwa C282.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Shindaiwa C282. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Shindaiwa C282 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
