Manuel d'utilisation / d'entretien du produit A794-D100 du fabricant Axiohm
Aller à la page of 140
A794 Thermal Receipt Printer Owner's Guide A794-D100 TM.
.
March 1999 i Legal Notices Disclaime r Infor mation in th is do cument is subje ct to chan ge w ithout n otice. Consul t your Ax ioh m s ale s representative for inform ation that is ap plicable and cu rrent. Axiohm reserves t he right to improve product s as new technology, c omponents, software, and firm ware become av ailable.
March 1999 ii In order to ensure compliance with the Product Safety, FCC and CE marking requirements, you must use t he power supply, po wer cord, and interface c able which were shipped wit h this pr.
A794 Owner’s Guide Contents March 1999 iii Contents Chapter 1: About the Printer .............................................................. 1 Description o f Printer .................................................................... 2 Models Available .
Contents A794 Owner’s Guide March 1999 iv Chapter 5: Communication Interface................................................ 33 Commun ication O verview ............................................................ 34 Interface ......................
Chapter 1: About the Printer ♦ Description of Printer ♦ Models Available Model Identification Communication Interfaces ♦ Installations On a Flat Surface On a Wall On a Flat Surface Vertically .
Chapter 1: About the Printer A794 Owner’s Guide March 1999 2 Description of Printer The A794 thermal receipt printer i s extremely fas t, quiet , and very reliable. Wi th thermal printing technology, there is no ribbon cassette to change, and paper loa d ing is extremely simple.
A794 Owner’s Guide Chapter 1: About the Printer March 1999 3 Models Available There are several models of th e printer depending on the commu nication interface an d the combination of options se lected . Model Identific ation See the illustration for the features designa ted by the printer ID number.
Chapter 1: About the Printer A794 Owner’s Guide March 1999 4 Installations You can set up the prin ter three ways: set it flat on any level surface, mo unt it vertically on any level surface, or mount it on a wa ll using a wall-mount kit. Either wa y, be sure to leave room to o pen the cover and access th e cables.
A794 Owner’s Guide Chapter 1: About the Printer March 1999 5 On a Fl at Su rface Vertically (see n o te) Features Interfaces RS-232C, Parallel Memory/Firmware 512K Flash Memory , Histo ry EEROM, 4K .
Chapter 1: About the Printer A794 Owner’s Guide March 199 9 6 Options ♦ Knife (Cutter) ♦ Wall Mount ♦ Power Su pply: 55 Watt/ 75 Watt ♦ Power Cords: US, SEV, UK AC Cord, and Australia AC Cord ♦ 1MB memory ♦ Paper Low Senso r ♦ Paper Width ♦ 82.
Chapter 2: Using the Printer ♦ Printer Controls ♦ Changing Paper ♦ Testing the Printer.
Chapter 2: Using the Printer A794 Owner’s Guide March 1999 8 Printer Controls Paper Fe ed Button LED (Green) Reset Button Reset Button Use the Reset Button to reset th e printer in case of a jam or fault con dition. When the Reset Button is pressed, the printer go es through a startup routine as if it h ad been turned off, then o n again.
A794 Owner’s Guide Chapter 2: Using the Printer March 1999 9 Tone A single beep indicates the printer has successfully completed its sta r tup routine ( a fter having been reset or the po wer supply turned on). If the printer beeps twice, a problem m ay be indicated.
Chapter 2: Using the Printer A794 Owner’s Guide March 1999 10 Changing Paper Change the paper wh en either of the fo llowing co nditions o ccurs: ♦ Colored stripe appears on the receipt paper in dicating the paper is low Change the pape r as soon as possible to a void running out of pa per par t wa y through a transaction.
A794 Owner’s Guide Chapter 2: Using the Printer March 1999 11 2. Remove the used ro ll. 3. Tear off the end of the n ew roll so that the edge is lo ose.
Chapter 2: Using the Printer A794 Owner’s Guide March 199 9 12 4. Place the new roll into the paper bucket with a few in ches of paper extending over the cabinet front (or top, if printer is mounted vertically) . Caution : Be sure the paper unrolls from the bottom of the roll.
A794 Owner’s Guide Chapter 2: Using the Printer March 1999 13 Testing the Printer Run this test to ch eck the printer. The test prints the settin gs for several functions, an d partially cuts the paper between each va riation. The printouts may vary depending on the model.
Chapter 2: Using the Printer A794 Owner’s Guide March 199 9 14 For more in f orma t ion a bout See t his section Poorly printed test pr intout “Troubleshooting the Pr inter”.
A794 Owner’s Guide Chapter 2: Using the Printer March 1999 15 Troubleshooting the Printer The printer is simple and generally trouble-free, but from time to time minor problems may occur. Follow these pro cedures to determine the cause and reso lution of any problems the printer m ay be having.
Chapter 2: Using the Printer A794 Owner’s Guide March 1999 16 Printing Problem s Problem Possible Causes What to Do Where to Go Colored stripe on the receipt. Paper is low. Change the paper. A794 Owner’s Guide Receipt does not co me out all the way.
Chapter 3: Media and Supplies Guide ♦ Ordering Thermal Paper Thermal Paper S pecifications Manufacturers How to Order ♦ Ordering Miscellaneous Supplies Ordering Cash Drawer s Ordering P ower Suppl.
Chapter 3: Media and Supplies Guide A794 Owner’s Guide March 1999 18 Ordering Thermal Paper Thermal Paper Specifications The printer requires qu alified thermal paper with the fo llowing dimensio ns: Width Diameter Leng th 80 mm ± .2 m m (3.15 in .
A794 Owner’s Guide Chapter 3: Media and Supplies Guide March 1999 19 Ordering Miscellaneous Supplies Ordering Ca sh Drawer s Order cash drawers from the followin g suppliers: Cash Drawers Number NCR 7052-K657 M-S Cash Draw er Corp.
Chapter 3: Media and Supplies Guide A794 Owner’s Guide March 1999 20 Ordering Com munication Ca bles Contact your sales representative to order the communica tion ca bles listed in the table. The numbers are fo r reference only. Suppliers may use ot her numbers.
Chapter 4: Print Specifications ♦ Characters Print Modes Size ♦ Paper Specifications ♦ Print Zones Print Zones for 80 mm Paper Print Zones for 82.
Chapter 4: Print Specifications A794 Owner’s Guide March 1999 22 Characters Print Modes Here are the available print modes. ♦ Standard ♦ Compressed ♦ Double High ♦ Double Wide ♦ Upside Dow.
A794 Owner’s Guide Chapter 4: Print Specifications March 1999 23 Paper Specifications The printer requires qu alified thermal thermal paper with the following dimensions: Width Diameter Leng th 80 mm ± .2 m m (3.15 in . ± .02 in.) 90 mm m ax. (3.27 in.
Chapter 4: Print Spec ific ations A794 Owner’s Guide March 1999 24 Print Zones for 82. 5 mm Paper Here are t he s pecifications of the print zone for 82.5 mm paper: ♦ 640 dots (ad dressable) @ 8 dots/m m, centered on 82.5 mm ♦ Sta ndar d mo d e: mi nimum ma rgins : 1 .
A794 Owner’s Guide Chapter 4: Print Specifications March 1999 25 Character Sets Code Page 4 37.
Chapter 4: Print Specifications A794 Owner’s Guide March 1999 26 Code Page 8 50.
A794 Owner’s Guide Chapter 4: Print Specifications March 1999 27 Code Page 8 52.
Chapter 4: Print Specifications A794 Owner’s Guide March 1999 28 Code Page 8 58.
A794 Owner’s Guide Chapter 4: Print Specifications March 1999 29 Code Page 8 60.
Chapter 4: Print Specifications A794 Owner’s Guide March 1999 30 Code Page 8 63 f.
A794 Owner’s Guide Chapter 4: Print Specifications March 1999 31 Code Page 8 65.
Chapter 4: Print Specifications A794 Owner’s Guide March 1999 32 Code Page 8 66.
Chapter 5: Communication Interface ♦ Communication Overview Interface Sending Commands ♦ RS-232C Int erface Print S peed and Timing XON/X OFF Pr otocol DTR/DSR Proto col RS-232C Technical Specific.
Chapter 5: Communication Interface A794 Owner’s Guide March 1999 34 Communication Overview In order for a receipt to be prin ted, a program must be in place that translates the data from the hos t computer into a language th at the printer can understand.
A794 Owner’s Guide Chapter 5: Communication Interface March 1999 35 RS-232C Interface The RS-232C in terface uses ei ther XO N/XOF F (softw are) or DTR /DSR (h ardware) protocol to co ntrol the flow of information betw een the computer and the prin ter.
Chapter 5: Communication Interface A794 Owner’s Guide March 1999 36 XON/XOFF Protocol The XON/X OFF characters coordin ate the information transfer between the prin ter and the host co mputer. The printer sends an XON character wh en it is ready to receive data and it sends a n XOFF charac te r when it cannot a ccept any mor e data.
A794 Owner’s Guide Chapter 5: Communication Interface March 1999 37 RS-232C Technical Specifications This section describes the pin settings for the connectors and the RS-232C interface parameters. The R S-232C parameters are select ed through the con figuratio n menu feature.
Chapter 5: Communication Interface A794 Owner’s Guide March 199 9 38 Cash Drawer Connector The following illustration shows the pinouts f or the cash dr awer connector . P i n 1 P i n 6 The following table shows the pinouts for the cash drawer. The connector can support two cash drawers w ith a Y cable, and is located at th e rear of the printer.
A794 Owner’s Guide Chapter 5: Communication Interface March 1999 39 Parallel Interface The printer i s also avai lable with an IEEE-1284 parallel in terface.
Chapter 5: Communication Interface A794 Owner’s Guide March 1999 40.
Chapter 6: Programming Information ♦ List of Commands ♦ Comparisons ♦ Command Descriptions Command Conventions Printer Function Commands Vertical Positioning and P rint Commands Horizontal P osi.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 42 Commands contro l all operations and fun ctions of the printer; fro m selecting the size and placement of characters and graphics on the receipt to feeding and cutting the paper.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 43 Code (Hexadecim al) Comman d Page 1B 25 n Select Character Set 70 1B 26 s c1 c2 n1 d1.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 44 Code (Hexadecim al) Comman d Page 1D 02 nn Select Flash Memory S e ctor to Downloa d 124 1D 03 n Real Time Request to Printer 103 .
A794 Owner’s Guide Chapter 6: Programming Information March 1999 45 Comparisons The following table details the list of comma nds whose beha vior differs from the A793(A756) and the A794(A758) because of th e physical differences of a 6 dots/ mm head (A793/A756) vers us an 8 do ts/m m head (A794/ A758).
Chapter 6: Programming Information A794 Owner’s Guide March 1999 46 Command Descriptions Command Conv entions The followi ng informatio n describes how each command is organ ized: Command Name A descriptive name (not th e ASCII code) used to identify the co mmand.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 47 Printer Function Commands The printer f unc tion c ommands control the f ollowing basic printer functions and a re described in or.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 48 Perform Partial Knife Cut Partially cuts the receipt. The length of the cut can be cha nged through the configuration m enu. The default setting leaves .20 in ches (5 mm) of paper on the left edge.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 49 Select Print Mode Selects the print mode: stan dard, compressed, emphasized, un derlined, double high, o r double wide.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 50 Select Peripheral Device (fo r Multi-Drop) Selects the device to which th e host computer sen ds data.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 51 Select Paper Sensors to Output Paper End Signals Specifies the paper sensor to output a pa per end signa l.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 52 Select Sensors to Stop Printing Selects the paper sensor used to detect wh en the paper is out. The prin ter finishes printing the curren t line and feeds the paper before sto pping.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 53 Read from Non-Volatile Memory Reads a two-byte word f rom location k in history EEROM.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 54 Write to Non-Volatile Memory (NVRAM) Writes two-byte word, n 1 n 2, to location k in history EEROM.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 55 Vertical Positioning and Print Commands The vertical positioning and print commands control the vertical print positions of characters on the receipt. Print and Feed One Line Prints one line fro m the buffer and feeds paper on e line.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 56 Feed n Dot Rows Feeds the paper n dot row s ( n /203 inch , n /8 mm), without printing.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 57 Print Prints one line fro m the buffer and feeds paper on e line. ASCII ETB Hexadecimal 17 Decimal 23 Set Column Prints the first character of the n ext print line in column n . It must be sent fo r each line not printed at co lumn one.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 58 Set Line Spacing Sets the line spacing to n /406 inch ( n /16 m m). The minimum line spacing is 8.5 lines per inch. The line spa cing equals the char a cter height when n is too small.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 59 Print and Feed n Lines Prints one line fro m the buffer and feeds paper n lin es at the current line height.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 60 Horizontal Positioning Commands The horizonta l positioning commands c ontr ol the horizonta l print positions of characters on the receipt. Horizontal Tab Moves the print position to the next tab position set by the Set Horiz onta l Tab Positions (1B 44 n 1 n 2 .
A794 Owner’s Guide Chapter 6: Programming Information March 1999 61 Set Absolute S tarting Position Sets the print starting positio n to the specified number o f dots (up to the right margin) from the beginni ng of the line. The prin t starting position is reset to the first column after each line.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 62 Set Horizontal Tab Positions Sets up to 32 hor izontal ta b positions n columns from column one, but do es not move the print position . See the Horizont al Tab command (09). The tab positions remain unchan ged if the character widths are changed after the tabs are set.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 63 Set Relativ e Print Pos i tion Moves the print starting po sition the specified number o f dots either right (up to the right margin) or left (up to the left m argin) of the current position.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 64 Compatibility Inf ormation (A794 receipt v s. A793 receipt) There is a differen ce in the n ormal behavio r of this command i n A794 Emulati on Mode as compared to the original A793.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 65 Set Left Margin Sets the left margin of the printin g area. The left margin is set to ((( nH X 256) + nL ) times horizontal motion unit) inches. The hor izontal motion units a re set by the Set Horiz ontal and Vertical Minimum Motion Units co mmand (1D 50).
Chapter 6: Programming Information A794 Owner’s Guide March 1999 66 Set Horizontal and Vertical Minimum Motion Units Sets the horizontal an d vertical motion units to 1/ x inch and 1/ y inch respectively. When x or y is set to 0, the default setting for tha t motion unit is used.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 67 Set Printing Area Width Sets the width o f the printing area. If the settin g exceeds the printable area, the maximum value of the printable area is used. Th e width of the printin g area is set to ((( nH X 256) + nL ) times horiz ontal motion unit) inche s.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 68 Print Ch aracteri sti cs Commands These commands control what the printed information looks like, selection of cha racter sets, definition of custom -defined characters, and setting of m argins.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 69 Select 90 Degree Counter-Clockwise Rotated Print Rotates characters 90 degrees coun ter-clockwise. The com mand remains in effect until the printer is reset or until a Clear Prin ter (10) or Cancel Rotated Prin t (1B 56) command is received.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 70 Select Charact er Set Selects the character set. When an undefined RAM character is selected, curren t active ROM Code Page character is used. See th e Printing Specification Guide for the character sets.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 71 Define User- Defined Charact er Set Defines and enters do wnloaded characters in to RAM. The comm and may be used to overwrite single characters. User-defin ed characters are available until power is turn ed off or the Initialize Prin ter command (1B 40) is received.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 72 Select or Cancel Underline Mode Turns underline mod e on or off. U nderlines c a nnot be printed f or spaces se t by the Horizontal Tab, S e t A bsolute Start Position, or S e t Relative Print Position commands.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 73 Copy Charac te r Set from ROM to RAM Copies characters in the active R OM set to RAM.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 74 Select or Cancel Emphasized Mode Starts or stops emphasized printin g. The printer is reset to the stan dard print mode after a Clear Printer (10) command is received.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 75 Select or Cancel Italic Print Turns Italic print mode on or off. The printer is reset to th e standard print mode after a Clear Printer (10) command is received.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 76 Select International Charact er Set See the previous comm and, Select Character Code Table (page 72) Select or Cancel 90 Degree Clockwise Rot ated Print Rotates characters 90 degrees clockwise.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 77 Select Or Cancel Whit e/Black Reverse Print Mode Turns on White/Black reverse prin ting mode. In Wh ite/Black reverse printing mode, print dots and non-print dots are reversed, which means that white chara cters are printed on a black backgroun d.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 78 Select Superscript or Subscript Modes Turns superscript or subscript modes on or off.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 79 Graph i cs Command s These commands are used to enter and print graphi cs data and are described in order of their hexadecimal codes. Print Raster Graphics Prints one row of data. n 1 .
Chapter 6: Programming Information A794 Owner’s Guide March 1999 80 Set Absolute S tarting Position Sets the print starting positio n for graphics at the specified n umber of dots from the beginning o f the line. The print starting po sition is reset to column one after each line.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 81 Select Bit Image Mode Sets the print resolution and enters one line o f graphics data into the print buffer. Excess data is accepted but ignored. Any print com mand is required to print the data, after which the printer returns to normal processing mode.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 82 Select Bit Image Mode (continued) Top of Bit Image 24-Dot Single- Density M ode dn MSB LSB d1 d2 d3 d4 d7 d5 d6 dn Select Single-Density Graphics Enters one line of 8-dot sin gle-density graphics into th e print buffer.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 83 Select Double-Density Graphics Enters one line of 8-dot do uble-density graphics into th e print buffer. Any print command is required to prin t the line, after which th e printer returns to no rmal processing mode.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 84 Select the Current Logo Selects a logo to be defined or prin ted. The active logo n remains in use until this command is sent again w ith a different logo n . When this comm and precedes a logo definition, that defin ition is stored in flash memory as logo n .
A794 Owner’s Guide Chapter 6: Programming Information March 1999 85 Define Downloaded Bit Image Enters a downloaded bit im age (such as a logo) into R AM or Flash with the n umber of dots specified by n 1 and n 2.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 86 Print Downloaded Bit Image Prints the downlo aded bit image in RAM or Flash at a density specified by m . It is ignored if any data is in the prin t buffer, if the downloaded bit im age is undefined.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 87 Printer Sta tus Comma nds These commands enable th e printer to commun icate with the ho st computer followi ng the selected handshaking proto col, either DTR/ DSR or XON/X OFF.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 88 Request Alternate St atus (parallel printers only) This command allows the printer to inform the host when the data in the buffer has been processed.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 89 Transmit Paper Sensor Status Sends status data to the hos t computer. The printer sends on e byte to the host com puter when it is not busy or in a fault condition. See the f ollowing table.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 90 Transmit Printer ID Transmits the printer ID specified by n . This command is a batch mode command; th at is, the response is transm itted after all prior data in the receive buffer has been processed.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 91 Transmit Printer ID, Remote Diagnostics Extension Performs the remot e diagnostic functions specified by n.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 92 Value of n Remote di agnost ic it em Function Hex Dec 31 49 Flash fir mware pa rt # Not available, cannot write to ROM 32 50 Flash.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 93 Value of n Remote di agnost ic it em Function Hex Dec 95 149 Boot firmware version Not available 96 150 Boot firmware version Not .
Chapter 6: Programming Information A794 Owner’s Guide March 1999 94 Select or Cancel Aut omatic Stat us Back (ASB) Enables or disables automatic sta tus back (ASB ) a nd specifies the status items. This command is a batch mode co mmand; that is, it is processed after all prior data in the receive buffer has been processed.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 95 Select or Cancel Auto matic Status Back ( ASB) (continued) Default 0 (ASB disabled) Exceptions If n = 0, ASB is disabled.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 96 Select or Cancel Auto matic Status Back ( ASB) (continued) Second By te ( E rror informati on) Bit Off/O n Hex Decimal S tatus for ASB 0 - - - Undefined 1 - - - Undefined 2 - - - Undefined 3O f f On 00 08 0 8 No knife error.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 97 Transmit Status Transmits the status specified by n . This is a batch mode command which tra nsmits the response after all prior data in the receive buffer has been processed.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 98 Transmit Status (continued) Cash Drawer Status ( n = 2 or n = 50) Bit Off/On Hex Decimal Status for Tr ansmit Status 0O f f On 00 01 0 1 One or both cash drawers open. Both cash drawers clo sed.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 99 Send Printer Software Version The printer returns 8 bytes con taining the bo ot and flash software version . The first 4 bytes returned are an ASCII string fo r the boot versio n. The second 4 bytes are an ASCII string for the flash version .
Chapter 6: Programming Information A794 Owner’s Guide March 1999 100 Real Ti me Co mmands The Real Time com mands provide an application interface to the printer even when the printer is not han dli.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 101 Moving Data through the Buffer Applications should not let the buffer f ill up with Rea l Time commands when the printer is busy at t he RS-232C in terface.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 102 Recognizing Data from the Printer An applica tion sending va r ious Real Time a nd non-Rea l Time comma nd s to which the printer responds can determin e which command a respo nse belongs to by th e table below.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 103 Real Time Request to Print er The printer responds to a req uest from the hos t specified by n . This command includes two sequen ces: GS and DLE. The op erations performed depen d on the value of n , according to th e followin g parameters.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 104 Real Time Status Transmission Transmits the selected one byte printer status specified by n in Real Time according to the followin g parameters. This command includes tw o sequences: GS and D LE.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 105 Real Time Status Transmission (continued) 2 = Transmit RS-232C B usy Status Bit Sta tus Hex Decimal Funct ion 0 Off 00 0 Fixed to Off. 1 On 02 2 Fixed to On. 2O f f On 00 04 0 4 Cover closed.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 106 Real Time Status Transmission (continued) 4 = Transmit Receipt Paper Status Bit Sta tus Hex Decima l Function 0 Off 00 0 Fixed to.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 107 Real Time Printer Status Transmission Transmits one byte status of the printer in real time. ASCII GS ENQ Hexadecimal 1D 05 Decimal 29 5 Value of By te Bit Sta tus H ex Deci mal Funct ion 0O f f On 00 01 0 1 Paper adequate.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 108 Bar Code Com mands These commands fo rmat and print bar codes an d are described in order of their hexadecimal codes. Select Printing Position of H RI Characters Prints HRI (Human R eadable Interface) characters above o r below the bar code.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 109 Select Bar Code Height Sets the bar code height to n do ts or n /203 in ch ( n /8 mm).
Chapter 6: Programming Information A794 Owner’s Guide March 1999 110 Print Bar Code (continued) Values First Variation: String term inated with NULL Character M Bar Code Dn , Lengt h 0 UPC-A 48- 57 .
A794 Owner’s Guide Chapter 6: Programming Information March 1999 111 Print Bar Code (continued) m Bar Code Dn , Lengt h 65 UPC-A 48- 57 (ASCII numerals) Fixed Leng th: 11, 12 66 UPC-E 48- 57 Fixed L.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 112 Page Mode Com mands Page mo de is one of two m odes th at the A794 prin ter uses t o operate. St andard mode i s typical of how most prin ters operate by printing data as it is received and feedin g paper as the various paper feed com mands are received.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 113 Print Data in Page Mode Collectively prints all buffered data in the printin g area.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 114 Select Standard Mode Switches from page m ode to standard mo de. In switching fro m page mode to standard mode, data buffered in .
A794 Owner’s Guide Chapter 6: Programming Information March 1999 115 Select Print Direction in Page Mode Selects the printing direction and start position in page mode.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 116 Set Print Area in Page Mode Sets the position an d size of the printing area in page mode.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 117 Select Charact er Size Selects the character height using bits 0 to 2 and selects the chara c ter width using bits 4 to 6, as fo .
Chapter 6: Programming Information A794 Owner’s Guide March 1999 118 Select Character Size ( continued) Value of n 1-8 = vertic al number of times normal f ont 1-8 = hor izontal numbe r of times nor ma l font Range of n 0-255 Default of n 11 hexadecimal Exceptions If n is out of the defined rang e, this command is ignored.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 119 Set Relative Vertical Print Posit ion in Page Mode Sets the relative vertical print starting positio n from the current po sition. This command can also c ha nge the horiz ontal and vertica l motion unit.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 120 Macro Command s These commands are used to select and perform a user-defined seq uence of printer operations.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 121 Execute Macro Executes a macro. After waiting for a specified period the printer w aits for the Paper Feed Button to be pressed. After the button is pressed, the printer executes the macro once.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 122 Flash Download Commands These commands are used to lo ad firmware into the printer. There are three ways to enter th e download m ode. 1. Powering the prin ter up with DIP Switch 1 down.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 123 Switch to Flash Download Mode Puts the printer in flash dow nload mode in preparatio n to receive commands controlling the downloading of objects into fla sh memory.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 124 Select Flash Memory Sector to Download Selects the flash sector (nn ) for which th e next download o peration applies. The values of the possible sector are restricted, depending upon the flash part type.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 125 Erase All Flash Contents Except Boot Sector Causes the entire flash mem ory to be erased. The printer returns ACK if the command is successful; NA K if it is unsuccessf ul. ASCII GS SO Hexadecimal 1D 0E Decimal 29 14 Exceptions Available only in downloa d mode.
Chapter 6: Programming Information A794 Owner’s Guide March 1999 126 Download to Act ive Flash Sector Contai ns a start address (ah x 256 + al) and coun t (ch x 256 + cl ) of binary by tes to l oad into the selected sector, follo wed by that many bytes.
A794 Owner’s Guide Chapter 6: Programming Information March 1999 127 Select Memory Type (SRAM/Flash) Where to Save Logos or User-Defined Fonts Specifies whether to load th e logos or user-defined characters to flash memory or to RAM (vola tile memory) .
Chapter 6: Programming Information A794 Owner’s Guide March 1999 128 Erase User Flash Sector Erases a page of flash memory an d sends a carriage return when the operation is complete.
A794 Owner’s Guide Index March 1999 129 Index —8— 80 mm paper print zones, 23 82.5 mm pap er print zones, 24 —A— Accessories. Se e Supplies —B— Bar codes, 5 BASIC sending commands, 34 .
Index A794 Owner’s Guide March 1999 130 —I— IEEE Bi-directional P arallel connector communication conn ector, 39 Interface. See RS-232C inte rface Interfac es, 5 —L— LED, 8 continuously flas.
A794 Owner’s Guide Index March 1999 131 two-to ne bee p, 1 5 —W— Wall-mount kit ordering, 20 —X— XON/XOFF protocol, 36.
Index A794 Owner’s Guide March 1999 132.
.
TM A794-D100 189- 9200223 0399 A XIOHM is the name an d mark of AXIOHM © 1999 AXIOHM Printed in U. S.A..
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Axiohm A794-D100 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Axiohm A794-D100 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Axiohm A794-D100, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Axiohm A794-D100 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Axiohm A794-D100, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Axiohm A794-D100.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Axiohm A794-D100. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Axiohm A794-D100 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
