Manuel d'utilisation / d'entretien du produit XG-C435X du fabricant Sharp
Aller à la page of 71
DA TA PR OJECT OR MODEL XG-C465X XG-C435X OPERA TION MANU AL Introduction Quic k Start Setup Connections Basic Operation Useful Features Appendix.
IMPOR T ANT • For your assistance in reporting the loss or theft of your Projector , please recor d the Model and Serial Numbers located on the bottom of the projector and r etain this information.
-1 Introduction Before using the pr ojector , please read this operation man ual carefully . There ar e two important reasons for prompt warranty r egistration of your new SHARP Projector , using the REGISTRA TION CARD packed with the projector .
-2 W ARNING: The cooling fan in this projector continues to r un for about 90 seconds after the projector enters the standby mode. During normal operation, when putting the projector into standby mode always use the ST ANDBY button on the projector or on the r emote control.
-3 Introduction -42 Picture Picture Mode Contrast Bright Red Blue CLR T emp Reset Signal Type COMP .1 Standard 7500K Auto SEL./ADJ. RETURN ENTER END 0 0 0 0 Using the Menu Screen Menu Selections Example: Adjusting “Bright” • This operation can also be performed by using the b uttons on the projector.
-4 Contents Preparing Switching the Eco+Quiet Mode .......................... 36 Selecting the Picture Mode ............................... 36 Resize Mode ...................................................... 37 Using the Remote Control as the Wir eless Computer Mouse .
-5 Introduction Reference Appendix Maintenance ................................................. 55 Replacing the Air Filter ................................ 56 Replacing the Air Filter ...................................... 56 Maintenance Indicators .
-6 PDF operation manuals in several languages are included in the CD-ROM, so that you can w ork with the pr ojector . T o utilize these manuals, you need to install Adobe ® Reader ® on your computer (Windows ® or Macintosh ® ). Please download Adobe ® Reader ® from the Inter net ( http://www .
-7 Introduction 1. Read Instructions All the safety and operating instructions should be read befor e the product is operated. 2. Retain Instructions The safety and operating instructions should be retained for future r eference. 3. Heed Warnings All warnings on the product and in the operating instructions should be adhered to.
-8 Ensur e that you read the following safeguar ds when setting up your pr ojector . Caution concerning the lamp unit ■ Potential hazard of glass par- ticles if lamp ruptures. In case of lamp rupture, contact your nearest Shar p A uthorized Pro- jector Dealer or Service Cen- ter for replacement.
-9 Introduction Caution regar ding usage of the projector ■ When using the projector , t a ke care not to sub- ject it to hard impact and/or vibration, as this can result in damage.
-10 Accessories Remote control <RRMCGA623WJSA> Tw o R-6 batteries (“AA” size, UM/SUM-3, HP-7 or similar) Po wer cord * F or U .S., Canada, etc. (6' (1.8 m)) <QACCD A007WJPZ> F or Europe , except U .K. (6' (1.8 m)) <QACCV A011WJPZ> * Use the power cord that corresponds to the w all outlet in y our countr y .
-11 Introduction Optional lenses ■ Lens Projection distance for 100" screen size Wide-zoom lens ( × 1.5 – 1.9) AN-C12MZ 9'11" – 12'5" (3.0 m – 3.8 m) T ele-zoom lens ( × 2.2 – 2.8) AN-C18MZ 14'10" – 18'10" (4.
-12 42 MENU button For displa ying adjustment and setting screens. 43 46 AUTO SYNC button For automatically adjusting images when connected to a computer. ENTER button For setting items selected or adjusted on the menu. 32 KEYSTONE button For entering the Keystone Correction mode.
-13 Introduction Projector (Rear View) * Using the Kensington Lock • This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the system for instructions on how to use it to secure the projector .
-14 Remote Control 30 ST ANDBY button For putting the projector into standby mode . 32 KEYST ONE button For entering the K eystone Correction mode. 35 FREEZE button For freezing images . 35 MA GNIFY (Enlarge/Reduce) buttons For enlarging/reducing part of the image.
-15 Introduction Using the Remote Control Inserting the Batteries 1 Pull down the tab on the cover and remove the cover towards the di- rection of the arro w . 2 Insert the included batteries. • Insert the batteries making sure the po- larities correctly match the and marks inside the battery compartment.
-16 Quick Start 7 ST ANDBY button 3 ON button 6 COMPUTER 1 button 37 ST ANDBY/ON button 6 INPUT buttons 6 ENTER button 4 Height Adjustment buttons 5 Zoom knob 5 Focus ring 4 Tilt dial Page 18 1.
-17 Quick Start Pag es 31, 32 4. Adjust the angle 5. Adjust the focus and the zoom Pag e 3 3 7. Tu rn the Power off Pag e 3 0 6. Select the INPUT mode Pag e 3 4 • • • • • This projector is equipped with an “Auto Keystone Correction” function that automatically corrects any trapezoidal distortion within the projected image.
-18 Setting Up the Projector For optimal image quality , position the projector perpendicular to the screen with the pr ojector’ s feet flat and level. Doing so will eliminate the need for Keystone correction and pr ovide the best image quality . (See page 32 .
-19 Setup Projection (PRJ) Mode The projector can use an y of the 4 projection modes, shown in the diagram below . Select the mode most appro- priate for the pr ojection setting in use. (Y ou can set the PRJ mode in “ Options2” me n u. See page 52 .
-20 Storing the Projector Lens cap Fixing band Info How to Use the Storage Case When storing the projector , attach the lens cap to the lens, and place it in the supplied storage case. 1 Open the co ver of the storage case. 2 Place the projector into the stor - ag e case .
-21 Connections Samples of Cables for Connection •F or more details of connection and cables, ref er to the operation manual of the connecting equipment.
-22 T erminal on the projector AUDIO (for COMPUTER/ COMPONENT 1, 2, DVI-D) AUDIO (for VIDEO, S-VIDEO) MONIT OR OUTPUT AUDIO (MONIT OR OUT) Equipment Audio-visual equipment Monitor Amplifier T erminal .
-23 Connections Connecting to a Computer Before connecting, ensure the power cor d of the projector fr om the A C outlet is unplugged, and that the devices to be connected are turned off . After making all connections, turn on the projector and then the other de vices.
-24 When connecting with a DVI digital cable The projector emplo ys the D VI digital input ter minal f or direct input of Digital Video signals from a computer . * When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.
-25 Connections Connecting to Video Equipment The image quality is highest in order of the Component signal, the RGB signal, the S-video signal and the Video signal. If your audio-visual equipment has a component output terminal or RGB output ter minal, use the COMPUTER/COMPONENT terminal 1 or 2 on the projector for video connection.
-26 When connecting video equipment with S-video output terminal When connecting video equipment with video output terminal Note • When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector , use a com- mercially av ailable cab le that fits in the projector terminal you want to connect.
-27 Connections Controlling the Projector by a Computer When the RS-232C terminal on the projector is connected to a computer , the computer can be used to control the projector and check the status of the projector . Refer to the “SETUP MANUAL ” contained on the supplied CD-ROM f or “RS-232C Specifications and Commands”.
-28 To RGB input terminal RGB cable (commercially available) RGB cable To RGB output terminal To COMPUTER/ COMPONENT 1 input terminal To MONITOR OUT terminal Monitor Computer When connecting to the LAN terminal using a LAN cable Note • When connecting to hub , use straight-through Category 5 (CA T .
-29 Connections A udio signals input from equipment connected to each audio input terminal of the projector can be output to audio equipment. Note • Tu rn off the po wer of both the projector and audio equipment when connecting.
-30 AC socket To AC outlet T urning the Pr ojector On/Off Info • When “Auto Restart” is set to “On”: If the power cord is unplugged fr om the outlet or the breaker switch is turned off when the pr ojector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on.
-31 Basic Operation Image Projection Height Adjustment button Side View Lens center T op View Using the Adjustment Feet The height of the projector can be adjusted using the adjustment feet when the screen is located higher than the projector , the screen is inclined or when the installation site is slightly inclined.
-32 Image Projection " On-screen Display (Keystone Correction mode) KEYST ONE button MOUSE/Adjustment buttons ( ' / " / / | ) RETURN button Compresses lower side.
-33 Basic Operation Adjusting the Lens The image is focused and adjusted to the screen size using the focus ring or zoom knob on the projector . 1 The focus is adjusted by rotat- ing the focus ring.
-34 Image Projection Switching the INPUT Mode Select the appropriate input mode for the con- nected equipment. On the remote control Press , , , or on the remote control to select the input mode. On the projector 1 1 1 1 1 Press an INPUT ( ' ' ' ' ' / " " " " " ) b utton.
-35 Basic Operation Adjusting the Volume Press / VO L on the projector or / VO L on the remote control to adjust the v olume . Note • Pressing or V OL will lower the v olume.
-36 Displaying and Setting the Break Timer This function allows you to show the remaining time for break during meeting. 1 Press BREAK TIMER. The break timer starts to count down from 5 minutes.
-37 Basic Operation Resize Mode This function allows y ou to modify or customize the resize mode to enhance the input image. De- pending on the input signal, y ou can choose a desired image.
-38 VIDEO/DTV ** ** * * * * 4:3 aspect ratio Squeeze Letter box 16:9 aspect ratio 16:9 aspect ratio (4:3 aspect ratio in 16:9) For 4:3 screen For 16:9 screen Input signal Image type NORMAL Video/DTV 4.
-39 Basic Operation Using the Remote Control as the Wireless Computer Mouse When connecting the projector and the computer with a USB cable, you can use the remote control as the computer mouse.
-40 Menu Items The follo wing shows the items that can be set in the pr ojector . Note • “Fine Sync” menu is only displayed when the projector input is COMPUTER/COMPONENT 1, 2 or DVI-D.
-41 Useful Features “Options1” menu “Language” menu “Options2” menu Options1 Lamp Timer (Life) Resize Image Shift Ke ystone Auto K eystone OSD Display Background Eco+Quiet Mode Auto P ower Off System Sound Menu P osition System Lock Auto Restart h ( 100%) VIDEO Normal On On Logo On On On Center Disable On SEL.
-42 Picture Picture Mode Contrast Bright Red Blue CLR T emp Reset Signal T ype COMP .1 Standard 7500K Auto SEL./ADJ. RETURN ENTER END 0 0 0 0 Using the Menu Screen Menu Selections Example: Adjusting “Bright” • This operation can also be perf ormed by using the buttons on the projector .
-43 Useful Features Picture Picture Mode Contrast Bright Red Blue CLR T emp Reset Signal T ype COMP .1 Standard 7500K Auto SEL./ADJ. RETURN ENTER END 0 0 0 0 3 Press ' ' ' ' ' or " " " " " to select the item y ou want to adjust.
-44 Picture Picture Mode Contr ast Br ight Red Blue CLR T emp Reset Signal T ype Dynamic Range DVI Standard 7500K D. PC RGB Standard SEL./ADJ . RETURN ENTER END 0 0 0 0 Menu operation Pag e 42 1 2 3 4.
-45 Useful Features Menu operation Pag e 42 Note • The Video signal can only be set in VIDEO or S-VIDEO mode. • When “Video System” is set to “Auto”, y ou may not receiv e a clear picture due to signal differ- ences. Should this occur, s witch to the video system of the source signal.
-46 Fine Sync Clock Phase H-P os V- Po s Reset Resolution Auto Sync Signal Info COMP .1 640 × 480 On SEL./ADJ. RETURN ENTER END 0 0 0 0 Computer Image Adjustment (“Fine Sync” menu) Menu operation Pag e 42 1 2 3 1 1 1 1 1 Adjusting the Computer Image If the optim um image cannot be obtained with Auto Sync adjustment, use the Fine Sync function.
-47 Useful Features Options1 Lamp Timer (Life) Resize Image Shift Ke ystone Auto K eystone OSD Display Background Eco+Quiet Mode Auto P ower Off System Sound Menu P osition System Lock Auto Restart h ( 100%) VIDEO Normal On On Logo On On On Center Disable On SEL.
-48 Using the “Options1” Menu Menu operation Pag e 42 4 4 4 4 4 Keystone Correction When the image is projected either from the top or from the bottom towards the screen at an angle, the image be- comes distorted trapezoidally . The function f or correct- ing trapezoidal distortion is called Keystone Correction.
-49 Useful Features Menu operation Pag e 42 Description A confirmation sound is made when the projector turns on/off. No confirmation sound is made. Selectable items On Off 9 9 9 9 9 Setting the System Sound Description Displa yed on the center of the image .
-50 Menu operation Pag e 42 When System Lock is set When System Lock is set, the keycode in- put screen appears after the po wer is turned on. When it appears, enter the right keycode to start projection. Failure to enter the keycode will cause images not to be pr ojected even when signals are entered to the projector .
-51 Useful Features Helpful Functions Set during Installation (“ Options2” menu) Menu operation Pag e 42 1 1 1 1 1 Setting a Password If you do not want other s to change the setting f or the “Options2” menu, set a passw ord. 1 Select “P assw ord”, then press | | | | | .
-52 8 8 8 8 8 Selecting the T ransmis- sion Speed (RS-232C) Make sure that both the projector and computer are set for the same baud rate. Description Tr ansmission speed is slow .
-53 Useful Features Menu operation Pag e 42 9 9 9 9 9 DHCP Client Setting Connect the LAN cable before turning the pro- jector on. If not, the DHCP Client function does not work. Select “On” for “DHCP Client”, then press ENTER . “Obtaining IP Address.
-54 q q q q q Confirming the Network Information for the Projector Y ou can confirm the MA C address and pr ojector name. w w w w w Returning to the Default Settings This function allows you to initialize the settings y ou have made in the projector .
-55 Appendix Cleaning the lens ■ Use a commercially available blower or lens clean- ing paper (for glasses and camera lenses) for clean- ing the lens. Do not use any liquid type cleaning agents, as the y may w ear off the coating film on the surface of the lens.
-56 Replacing the Air Filter • This projector is equipped with air filters to ensure the optimal operating condition of the projector . • Ask your nearest Sharp A uthorized Pro- jector Dealer or Service Center to ex- c hange the filter (PFILD A022WJKZ) when it is no longer possible to clean.
-57 Appendix 5 Place a replacement air filter . • Place the new air filter onto the filter co ver . 6 Replace the filter co ver . • Slide the filter cover in the direction of the arrow to close it. Note • Ensure the filter cov er is securely installed.
-58 Po w er indicator Lamp indicator T emperature warning indicator Maintenance Indicators Maintenance Indicators ■ The warning lights on the projector indicate pr oblems inside the projector . ■ If a problem occurs, either the temperature indicator or the lamp indicator will illuminate red, and the pr ojector will enter the standby mode.
-59 Appendix Maintenance indicator Problem Cause P ossible solution T emperature warning indicator Normal Abnormal Off Red on (Standby) The internal temperature is abnormally high. Abnormal • Blocked air intake • Relocate the projector to an area with proper ventilation (see page 8 ).
-60 Lamp ■ It is recommended that the lamp unit (optional: AN-C430LP) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality . The lamp life (per centage) can be chec ked with the on-screen display .
-61 Appendix Securing screws Optional accessory Lamp unit AN-C430LP Removing and Installing the Lamp Unit W arning! • Do not remov e the lamp unit from the pro- jector right after use. The lamp and par ts around the lamp will be v er y hot and may cause burn or injur y .
-62 5 Insert the new lamp unit. • Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws. 6 Replace the lamp unit cover . • Align the lamp unit cover and slide it to close. Then tighten the user service screw to secure the lamp unit co ver .
-63 Appendix Note • This projector ma y not be able to displa y images from notebook computers in simultaneous (CR T/LCD) mode. Should this occur , tur n off the LCD display on the notebook computer and output the displa y data in “CRT only” mode.
-64 Tr oubleshooting Check • Projector pow er cord is not plugged into the wall outlet. • Po w er to the e xternal connected devices is off . • The selected input mode is wrong. • The A V MUTE function is working. • Cables incorrectly connected to the rear panel of the projector .
-65 Appendix Check Problem P age Maintenance indicator illuminates or b links in red. The projector cannot be turned on or put into the standby mode using the ST ANDBY/ON button on the projector . Picture is green with component input signals (COMPUTER/ COMPONENT 1, 2, DVI-D) .
-66 For SHARP Assistance If y ou encounter any pr oblems during setup or operation of this projector , first refer to the “T roubleshooting” section on pages 64 and 65 . If this operation manual does not answer y our question, please contact the SHARP Service depar tments listed below .
-67 Appendix Specifications As a par t of policy of continuous improv ement, SHARP reser v es the r ight to mak e design and specification changes f or product improv ement without prior notice. The performance specification figures indicated are nominal v alues of production units.
-68 2D Progressiv e ......................................................... 45 3D Progressiv e ......................................................... 45 AC soc ket .................................................................. 30 Adjustment buttons .
SHARP CORPORA TION.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Sharp XG-C435X c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Sharp XG-C435X - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Sharp XG-C435X, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Sharp XG-C435X va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Sharp XG-C435X, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Sharp XG-C435X.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Sharp XG-C435X. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Sharp XG-C435X ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
