Manuel d'utilisation / d'entretien du produit XE-A40S du fabricant Sharp
Aller à la page of 116
ELECTRONIC CASH REGISTER CAJA REGISTRADORA ELECTRONICA INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES XE-A40S MODEL MODELO.
FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user ’ s authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
1 English English INTRODUCTION Thank you very much for your purchase of the SHARP Electronic Cash Register, Model XE-A40S. Please read this manual carefully before operating your machine in order to gain full understanding of functions and features. Please keep this manual for future reference.
CONTENTS INTRODUCTION ............................................................................................................................................1 IMPORTANT .............................................................................
PRIOR TO PROGRAMMING ......................................................................................................................27 BASIC FUNCTION PROGRAMMING (For Quick Start) ................................................................
4 P ARTS AND THEIR FUNCTIONS Front view Rear view External View 1 The printer is a receipt/journal dual station type thermal printer, and therefore it does not require any type of ink ribbon or cartridge. Lift the rear of the printer cover to remove. To re-install, hook the pawls on the cabinet and close.
5 The mode switch can be operated by inserting one of the two supplied mode keys - manager (MA) and operator (OP) keys. These keys can be inserted or removed only in the “ REG ” or “ OFF ” position. The mode switch has these settings: OFF: This mode locks all register operations.
6 This key locks and unlocks the drawer. To lock it, turn 90 degrees counterclockwise. To unlock it, turn 90 degrees clockwise. Drawer Loc k Key 6 Operator display • Clerk code or Mode name The mode you are in is displayed. When a clerk is assigned, the clerk code is displayed in the REG or OP X/Z mode.
7 GETTING ST AR TED Please follow the procedure shown below. Initializing the cash register In order for the cash register to operate properly, you must initialize it before operating for the first time. Follow this procedure. 1. Make sure the power cord plug is not inserted into the AC outlet.
8 Precaution: The paper cutter is mounted on the printer (receipt side). Take caution when installing paper rolls. The register can print receipts and journals. For the printer, you must install the paper rolls (receipt and journal paper rolls) provided with the register.
9 5. Set a paper roll in the paper roll cradle of the journal side. 6. Insert the end of the paper into the paper chute of the printer until it is caught by the printer auto-feed and comes out of the top of the printer. If the printer does not catch the paper, feed the paper while pressing the } key.
10 Now you are ready for sales registration. Starting sales entries 7 • Amount entry digit limit for PO amount, RA amount, Manual tax amount The factory setting makes the maximum amount you can enter.
11 O VER VIEW OF FLO W OF D AIL Y SALES ENTRIES Things to do before starting sales entries: • Make sure the power cord is securely connected to the AC outlet. • Turn the mode switch to OP X/Z position and check if date and time are correctly set. • Replace the till, if removed for safety.
12 BASIC SALES ENTR Y Listed below is a basic sales entry example when selling items by cash. For operation details, please refer to each section. Mode switch setting 1. Turn the mode switch to the REG position. Clerk assignment 2. Enter your clerk code.
13 Clerk assignment Prior to any item entries, clerks must enter their clerk codes into the register. However, the code entry may not be necessary when the same clerk handles consecutive transactions. Receipt ON/OFF function You can disable receipt printing in the REG mode to save paper using the receipt ON/OFF function.
14 Single item entries Department entries For a merchandise classification, the cash register provides a maximum of 99 departments. To the departments, group attributes such as taxable status are applied to items when they are entered.
15 Example: Selling a dept. 12 item ($12.00) , a dept. 21 item ($5.00), a dept. 14 item (using preset price), a dept. 22 item (using preset price), and a dept. 50 item ($15.00), a dept. 41 item (using preset price), a PLU 2 item (PLU entry) and a PLU 12 item (subdept.
16 Split pricing entries This function is practical when the customer wants to purchase items normally sold in bulk. To realize this function, you must change the programmed setting. Refer to “ Various Function Selection Programming 1 ” ( job code 70 ) for programming details.
17 Single item cash sale (SICS) entry • This function is useful when a sale is for only one item and is for cash. This function is applicable only to those departments that have been set for SICS or to their associated PLUs or subdepartments.
18 Check tendering Cash or chec k sale that does not require entry Enter items and press the A key if it is a cash sale or press the C if it is a check sale. The register will display the total sale amount. Charge (credit) sale Enter items and press a charge key ( X or Y ).
19 A utomatic tax When the register is programmed with a tax rate (or tax table) and the tax status of an individual department is set for taxable, it computes the automatic tax on any item that is entered directly into the department or indirectly via a related PLU.
20 T ax status shift The machine allows you to shift the programmed tax status of each department or the PLU key by pressing the T and/or U keys before those keys. After each entry is completed, the programmed tax status of each key is resumed. Example: Selling the following items for cash with their programmed tax status reversed • One $13.
21 OPTIONAL FEA TURES Discount and premium entries using the percent ke y The percent key is used to apply a manually entered or preset discount or premium percent rate to individual items or to a merchandise subtotal. In the default setting, you can manually enter a discount percent rate to both individual items and merchandise subtotal.
22 Discount for merchandise subtotal Discount for item entries Refund entries For a refund of a department item, start with entering the refund amount and press the f key, then press the corresponding.
23 Currency conversion The register allows payment entries in a foreign currency (only cash payment is available). Pressing the V key creates a subtotal in the foreign currency.
24 Received-on account and paid-out entries When you receive on account from a customer or when you pay an amount to a vendor, use the r key or the R key respectively. For the received-on-account (RA) entry, enter the amount, and press the r key. For the paid-out (PO) entry, enter the amount and press the R key.
25 CORRECTION If you make an incorrect entry relating to a department, PLU/subdepartment, percentage ( % and & ), discount ( - ) or refund, you can void this entry by pressing the v key immediately after the incorrect entry.
26 You can void an entire transaction. Once subtotal void is executed, the transaction is aborted and the register issues a receipt. This function does not work when more than 30 items have been entered. Any errors found after the entry of a transaction has been completed or during an amount tendered entry cannot be voided.
27 PRIOR T O PROGRAMMING Before starting sales entries, you must first program necessary items so the cash register suits your sales needs. In this manual, there are three sections, BASIC FUNCTION PRO.
28 Time For setting the time, enter the time in 4 digits using the 24-hour format. For example, when the time is set to 2:30 AM, enter 230; and when it is set to 2:30 PM, enter 1430.
29 Example: Programming the tax rate 4% as tax rate 2 with tax exempt as 12¢ • If you make an incorrect entry before pressing the third @ key in programming a tax rate, cancel it with the l key. • You do not need to enter the trailing zeros of a tax rate (after the decimal point), but you do need to enter the decimal for fractions.
30 The first figure to be entered depends upon whether the difference between a minimum breakpoint to be entered and the preceding minimum breakpoint is not less than $1.00 or more than 99¢. When the difference is not less than $1.00, enter “ 1, ” and when it is not more than 99¢, enter “ 0 ” or nothing.
31 • If the tax is not provided for every cent, modify the tax table by setting the tax for every cent in the following manner. When setting the tax, consider the minimum breakpoint corresponding to unprovided tax to be the same as the one corresponding to the tax provided on a large amount.
32 A UXILIAR Y FUNCTION PR OGRAMMING Merchandise can be classified into a maximum of 99 departments. Items sold using the department keys can later be printed on a report shown as the quantities sold and sales amounts classified by department. The data is useful for making purchasing decisions and other store operations.
33 Commission group number • A commission group (0 to 2, 0: non commission) can be assigned to each department for commission for clerks. Each commission amount for each clerk is calculated based on a programmed commission rate and later printed on clerk reports.
34 The PLU function allows speedy key entries whereby a price is automatically called up when a code is entered. The subdepartment is a kind of “ open PLU ” , which requires you to enter a price after the PLU code is entered. A maximum of 1800 PLU/subdepartment settings are possible.
35 *: Item: Selection: Entry: A Commission group number 0-2 (0: Non commission) B PLU/subdepartment selection Subdepartment 0 PLU 1 When you program the last PLU code, the programming sequence will be complete with a press of the s key.
36 C , X , Y and A Compulsory entry of amount tender (not compulsory), entry digit limit (8 digits), footer printing (not printed) t (Manual tax) Entry digit limit (7 digits) * Item %/Item _ : Percent/discount calculation is applied to individual department and PLU/subdepartment.
37 P er cent rate limitation for % and & • Percent entries that exceed the upper limit may be overridden in the MGR mode. • 10.00% can be entered as 10 or 10P00 .
38 Entry digit limit (For discount key only) • The entry digit limit is in effect for the REG-mode operations but can be overridden in the MGR mode. The entry digit limit is represented by the number of allowable digit for the maximum entry amount for discount key.
39 Function parameters f or C , X , Y and A (when using as CA key) * 1: Item: Selection: Entry: A Footer printing Allow 1 Disallow 0 B Amount tendered entry Compulsory 1 Non-compulsory (for the CA or .
W Toggles between single-size and double-size characters. By default, the single-size character is selected. Once the W key is pressed, you are locked in for entering double size characters. “ W ” is displayed when double-size characters entry is selected as shown in the operator display example below.
41 Alphanumeric character code table (DC): Double-size character code ✱ ✱ Code 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 0.
42 Department text (item label) *To program departments 21 through 40, press the department shift key. PLU text (item label) Function text * Function no.
43 List of function texts 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 ( – ) %1 %1 %2 %2 Net sales total NET1 Net taxable 1 subtotal TAX1 ST .
44 • The items marked with “ * ” are for Canada only. • The items marked with “**” are for display only. • The function no. 55 “Exempt VAT” is only effective for the Canadian tax system (2 GST, VAT type). Clerk names Logo messages The register can print programmed messages on every receipt.
45 Logo print format (6 types) To print the logo message “THANK YOU” using double sized characters and centering on the third line. A 6-line logo message is preprogrammed when shipped. Please start entering from the first line when you first program a logo message.
46 AD V ANCED PR OGRAMMING Register number and consecutive number are printed on every receipt and journal. When your store has two or more registers, it is practical to set separate register numbers for identification. The consecutive number is increased by one each time a receipt and/or journal is issued.
47 *1 Enter job code using numeric keys specified in each section below. *2 Data entry details are listed on each table in each section below. An asterisk is entered for factory setting.
48 Receipt print format Job code: 7 * Item: Selection: Entry: A Always enter 0. (Fixed position) 0 B Always enter 0. (Fixed position) 0 C Subtotal print with a press of subtotal key Disallow subtotal .
49 Job code: 62 * Item: Selection: Entry: A Always enter 0. (Fixed position) 0 B Error beep activation By lock error* 0 By misoperation 1 C Key touch sound availability Allow to sound* 0 Disallow it 1.
50 Tax calculation system • For US tax system, select “ auto-tax ” . • For Canadian tax, from the table below, specify a tax system suitable for your province (if necessary contact your local tax office for correct sales tax information) and for your type of retail business.
51 The cash register provides various options so you can use the register to suit your sales needs. In this section, you can program the following features (parameters within parentheses indicates def.
52 Logo message print format You can select the number of lines for your logo message, and the position to print it on receipt. For details of the logo message type, please refer to “Logo messages” on pages 44 and 45 .
53 Thermal printer density * By default, 50 is set. To make the print darker, set a larger number, and to make the print lighter, set a smaller number. Language selection *Language: 0: English 2: French 3: Spanish When you change the language, the text such as clerk name, logo message and function text will be reset to the default settings.
54 AUTO key programming — Automatic sequence key If you program frequently performed transactions or report sequences for the a key, you can call those transactions and/or reports simply by pressing the a key in key operations. Programming for a ; entering a PLU 2 item (programmed unit price: 1.
55 Mode Dept. code Function no.& its text Dept. unit price w/sign Dept. function Dept. group & commission group Minus department Function parametrs (F-H) Function parametrs (F-H) Discount amt.
56 2 Programming report 2 Job code A to H from the left Training clerk specification Language selection * Job code #63, 64, 65, 67, 68, 69, 71, 72, 76, 77, 85, 87 and 95 are fixed settings, for which you cannot change the settings.
57 READING (X) AND RESETTING (Z) OF SALES T O T ALS • Use the reading function (X) when you need to take a reading of sales information entered since the last reset. You can take this reading any number of times. It does not affect the register ’ s memory.
58 • When both sales quantities and sales amounts are zero, printing is skipped. If you do not want to skip, change the programming. (Refer to “ Print format ” of “ Various Function Selection Programming 1 ” .) • “ X ” represents read symbol and “ Z ” represents reset symbol in the reports.
59 Full sales report • Sample report Daily Sales T otals 2 Taxable 1 total Gross tax 1 total Refund tax 1 total Net tax 1 total Mode title*1 Reset counter Net grand total(GT2-GT3) Dept. code Sales q'ty Sales amount “ + ” dept. counter and total “ + ” bottle return dept.
60 PLU report by designated range • Sample report *: When you take Z1 report, “ Z1 ” is printed. PLU code Item label Mode title* Report title Range Range sum Sales q'ty and total Department.
61 T otal in drawer report • Sample report Cash in drawer Cash plus check in drawer Mode title Report title T ransaction report • Sample report This report shows the same transaction data as when a full sales report is run.
62 Daily net reports • Sample report *: When you take Z report, “ Z2 ” is printed instead of “ X2 ” . Customer counter Sales total Net amount total Mode title* Date Customer total General information The periodic reading or resetting reports are the same in format as those in the X1/Z1 report for daily sales.
63 O VERRIDE ENTRIES Programmed limit for functions (such as for maximum amounts) can be overridden by making an entry in the MGR mode. In this example, the register has been programmed not to allow discounts entries over $1.00. REG-mode 1500 £ entries 250 - .
64 OPERA T OR MAINTENANCE When power is lost, the machine retains its memory contents and all information on sales entries. • When power failure is encountered in register idle state or during an entry, the machine returns to normal operation after power recovery.
65 Be sure to use paper rolls specified by SHARP. The use of any other paper rolls other than those specified could cause paper jamming, resulting in register malfunction. Paper specification Paper width: 1.75 ± 0.02 in (44.5 ± 0.5 mm) Max. outside diameter: 3.
66 8. Remove the outer side of the take-up spool as shown on the left. 9. Remove the printed journal roll from the take-up spool. Installing the paper roll Caution: The paper cutter is mounted on the printer (receipt side). Be careful not to cut yourself.
67 Caution: The paper cutter is mounted on the printer (receipt side). Be careful not to cut yourself. Never touch the print head immediately after printing, because the head may still be hot.
68 The till in the register is detachable. After closing your business for the day, remove the till from the drawer and keep the drawer open. To detach the drawer, pull it forward fully with the till removed. And remove it by lifting it up. The 6-denomination coin case is detachable.
The malfunctions shown in the left-hand column below, labelled “ Fault, ” do not necessarily indicate functional faults of the machine. It is therefore advisable to refer to “ Checking ” shown in the right-hand column before calling for service.
70 SPECIFICA TIONS Model: XE-A40S Dimensions: 16.5 (W) x 16.8 (D) x 11.7 (H) in. (420 (W) x 427 (D) x 297 (H) mm) Weight: 28.0 Ib (12.7 kg) Power source: 120V AC ± 10%, 60 Hz Power consumption: Stand-by 8.6W Operating 49W (max.) Working temperature: 32 °F to 104 °F (0 °C to 40 °C) Electronics: LSI (CPU) etc.
71 Function Te x t Unit price Dept. code BR G CM T4 T3 T2 T1 SICS SIGN LMT ENT ABC D E FG H I J K 010 0 0 01 0053 Ex. 5 FRUIT 100 Programming sheet f or departments (Please make copies of this sheet.) F or details of pro gr amming, re f er to pages 32 , 33 , and 42 .
72 Function Te x t Unit price/ Limit amount PLU code Associated dept. CM TYPE AB 1 1 MELON Ex. 1 125 1 Programming sheet f or PLUs/subdepartments (Please make copies of this sheet.) F or details of pro gr amming re f er to pages 34 , 35 and 42 . Unit price/Limit amount Max.
1 English Español INTRODUCCION Le agradecemos la adquisición de la caja registradora electrónica SHARP modelo XE-A40S. Sírvase leer este manual detenidamente antes de hacer funcionar la caja registradora para familiarizarse y comprender por completo sus funciones y características.
INDICE INTRODUCCION............................................................................................................................................1 IMPORTANTE ...............................................................................
3 P ARTES Y SUS FUNCIONES V ista delantera Vista trasera V ista exterior 1 La impresora es una impresora térmica de recibos/registro diario de dos estaciones, y por lo tanto no requiere ningún tipo de cartucho ni cinta entintada. Levante la parte posterior de la cubierta de la impresora para extraerla.
4 El selector de modo funciona insertando una de las dos llaves de modo suministradas: la llave del administrador (MA) y la del operador (OP). Estas llaves pueden insertarse o sacarse sólo cuando el selector esté en la posición “REG” u “OFF”.
5 Esta llave bloquea y desbloquea el cajón. Para bloquear el cajón, gire la llave 90 grados hacia la izquierda. Para desbloquearlo, gírela 90 grados hacia la derecha. Llave de la cerradura del cajón 6 V isualizador para el operador • Código de dependiente o nombre de modo Se visualiza el modo en el que ahora se encuentre.
6 P ARA EMPEZAR Siga el procedimiento mostrado a continuación. 1. Inicialice la caja registradora. Para que la caja registradora pueda funcionar correctamente, deberá inicializarla antes de ponerla en funcionamiento por primera vez. Siga el procedimiento siguiente.
7 P ARA EL OPERADOR REGISTRO BASICO DE VENT AS A continuación se muestra un ejemplo de registro básico de ventas en metálico de artículos. Para los detalles de la operación, consulte cada sección respectiva. Ajuste del selector de modo 1. Gire el selector de modo a la posición REG.
8 Función de activación/desactivación (ON/OFF) de recibo Podrá inhabilitar la impresión de recibos en el modo REG. Pulse la tecla R en la posición OP X/Z.
9 • Cuando se emplea la tecla de registro de código de sección * 1 Menos que los importes de límite superior programado Cuando se introduce cero, sólo se añade la cantidad de ventas. Registros de PLU/subsecciones La caja registradora ya está programada para el modo PLU y cero para el precio unitario.
10 Registros de venta en metálico de un solo artículo (SICS) • Esta función es útil cuando se vende solamente un artículo en metálico. Esta función es aplicable sólo a las secciones que se han ajustado para SICS o a sus PLU o subsecciones asociadas.
11 Impuestos automáticos Cuando se ha programado una tasa de impuestos (o tabla de impuestos) en la caja registradora y el estado de impuestos para una sección individual está ajustado a imponible,.
12 Cálculo porcentual para el subtotal de mercancías Cálculo porcentual para registros de artículos Registros de descuento y recargo empleando la tecla de descuento La tecla de descuento se emplea para aplicar un importe de descuento o recargo manualmente introducido o preajustado a artículos individuales o a un subtotal de mercancías.
13 En ambos casos, la vuelta se visualizará en moneda nacional y, cuando el importe recibido sea insuficiente, el déficit se mostrará en moneda nacional. • Pulse la tecla l después de pulsar la tecla V para cancelar el pago en una divisa. • Si se programa, se imprime un símbolo de moneda extranjera.
Podrá cancelar cualquier registro de sección incorrecto, registro de PLU/subsección o registro de devolución de artículo hechos durante una transacción, si lo encuentra antes de finalizar la transacción (por ejemplo, pulsando la tecla A ). Esta función es aplicable sólo a los registros de sección, PLU/subsección y de devolución.
15 PROGRAMACION DE LAS FUNCIONES BASICAS (Para el inicio rápido) Para programar la caja registradora, ponga la llave del administrador en el selector de modo y gírelo a la posición PGM. Fecha Para ajustar la fecha, introduzca la fecha con 8 dígitos empleando el formato de mes-día-año (MM/DD/AAAA), y pulse entonces la tecla s .
16 Ejemplo: Programación de la tasa de impuestos del 4% como tasa de impuestos 2 con exención de impuestos de 12¢ T abla de impuestos (aplicable al impuesto añadido) Si se encuentra en una localidad que emplea una tabla de impuestos para el cálculo de los impuestos, podrá programar consecuentemente la caja registradora.
17 Este primer número que se introduce depende de si la diferencia entre un punto de división mínimo a introducirse y el punto de división mínimo anterior no son de menos de $1,00 ni de más de 99¢. Cuando la diferencia no sea de menos de $1,00, introduzca “1”, y cuando no sea de más de 99¢, introduzca “0” o no introduzca nada.
18 * 2: Elemento: Selección: Registro: A Tipo Devolución de botellas 1 Normal 0 B Número de grupo 0-9 (0: Sin grupo) C Número de grupo de comisión 0-2 (0: Sin comisión) D Estado de impuestos 4 I.
19 La función de PLU permite realizar registros rápidos con las teclas en los que el precio se busca automáticamente al introducir un código. La subsección es un tipo de “PLU abierta”, que requiere que usted introduzca un precio detrás del código de PLU.
20 T asa para % , & y V *: Tasa 0,00 – 100,00 (Tasa de porcentaje) 0,0000 – 9999,9999 (Tasa de conversión de divisas) Importe para - Límite de tasa porcentual para % y & • Los registros porcentuales que exceden al límite superior pueden suprimirse en el modo MGR.
21 *: Elemento: Selección: Registro: A Estado de impuestos 4 Imponible 1 No imponible 0 B Estado de impuestos 3 Imponible 1 No imponible 0 C Estado de impuestos 2 Imponible 1 No imponible 0 D Estado .
22 * 1: Elemento: Selección: Registro: A Impresión de pie del recibo Habilitar 1 Inhabilitar 0 B Registro de importe recibido Obligatorio 1 No obligatorio (para las teclas CA o CHK) 0 Invalidar (par.
23 Para programar la palabra “Clerk01” con la letra “C” de tamaño doble. Para que la letra “C” sea de tamaño doble Para que el tamaño de los caracteres vuelva al normal Para cambiar a l.
24 T exto de sección (etiqueta de artículo) *Para programar las secciones 21 a 40, pulse la tecla de cambio de sección. T exto de PLU (etiqueta de artículo) T exto de función * Número de función: Vea la “Lista de textos de función” mostrada de la página siguiente.
25 Lista de textos de función 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 (–) %1 %1 %2 %2 Total neto de ventas N.
26 • Los ajustes iniciales son los de español (cambio del ajuste de programación para selección del idioma al español). • Los elementos marcados con “*” son sólo para Canadá. • Los elementos marcados con “**” son sólo para la visualización.
27 PROGRAMACION A V ANZADA El número de caja registradora y el número consecutivo se imprimen en el recibo y en el registro diario. Número de caja registradora Ajuste de números consecutivos La caja registradora ofrece varias funciones detalladas como las que se mencionan a continuación.
28 Selección de función para teclas misceláneas Código de tarea: 5 * Elemento: Selección: Registro: A PO en el modo REG Habilitar la operación PO en el modo REG* 0 Inhabilitarla 1 B RA en el mod.
29 Selección de función para impuestos Código de tarea: 15 * Elemento: Selección: Registro: A Introduzca siempre 0. (Posición fija) 0 B Introduzca siempre 0. (Posición fija) 0 C Introduzca siempre 0. (Posición fija) 0 D Introduzca siempre 0. (Posición fija) 0 E Introduzca siempre 0.
30 Código de tarea: 66 * Elemento: Selección: Registro: A Impresión de un recibo después de la Sólo el total 0 transacción Detalles* 1 B Impresión del importe cuando el precio Habilitar la impr.
Formato de impresión del mensaje del membrete Podrá seleccionar el número de líneas del mensaje del membrete, y la posición en la que se imprime en el recibo.
32 Especificación de dependientes de instrucción para el modo de instrucción Para los detalles sobre la instrucción de dependientes, consulte el “MODO DE INSTRUCCION” en la página 33 .
MODO DE INSTRUCCION El modo de instrucción se utiliza cuando el operador o el administrador practica las operaciones de la caja registradora. Cuando se selecciona un dependiente que está en instrucción, la máquina se establece automáticamente en el modo de instrucción.
• Cuando las cantidades de ventas y los importes de ventas son cero, se pasa por alto la impresión. Si no desea que se pase por alto, cambie la programación. (Consulte el apartado de “Formato de impresión” de la sección “Programación 1 de selección de diversas funciones”.
REGISTROS DE ANULACION El límite programado para las funciones (tales como importes máximos) puede anularse haciendo un registro de anulación en el modo MGR.
36 • Si no va a utilizar la caja registradora durante mucho tiempo, tire de la palanca de liberación del cabezal de impresión hacia usted para que el cabezal de impresión se aleje de la placa.
37 3. Pulse la tecla } para hacer avanzar el papel de registro diario hasta que la parte impresa salga del paso. 4. Corte el papel y extraiga el carrete de toma. 5. Corte el papel detrás de la impresora y cerca del rollo de papel. 6. Pulse la tecla } hasta que el papel que queda en la impresora salga por completo.
38 4. Vuelva a poner la palanca de liberación del cabezal de impresión a su posición original. 5. Ponga correctamente el rollo de papel siguiendo los pasos mencionados en “Instalación del rollo de papel”. 6. Vuelva a colocar la cubierta de la impresora.
39 El cajón se abre automáticamente. Sin embargo, cuando haya un fallo o corte de la corriente o la registradora quede fuera de servicio, deslice la palanca situada en la parte inferior de la registradora en la dirección de la flecha. (Vea la figura a la izquierda.
40 D 22 2 E 21 1 1 I 27 7 J 26 6 N 32 12 O 31 11 S 37 17 T 36 16 B 24 4 C 23 3 G 29 9 H 28 8 L 34 14 M 33 13 Q 39 19 R 38 18 E 21 Ejemplo: Leche Pan A 25 5 F 30 10 K 35 15 P 40 20 Emplee estas etiquetas con las teclas de sección.
LIMITED W ARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when shipped in its original container, will be free f.
SHARP ELECTRONICS CORPORATION SHARP CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135 1-800-BE-SHARP For additional information and product registration, please visit www.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Sharp XE-A40S c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Sharp XE-A40S - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Sharp XE-A40S, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Sharp XE-A40S va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Sharp XE-A40S, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Sharp XE-A40S.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Sharp XE-A40S. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Sharp XE-A40S ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
