Manuel d'utilisation / d'entretien du produit PN-E471 du fabricant Sharp
Aller à la page of 43
PN-E471 PN-E421 LCD MONIT OR OPERA TION GUIDE.
2 E This guide contains instructions regarding operation, settings, and similar details. For instructions regarding connection and installation, refer to the included Operation Manual. Manual Scope - Microsoft, Windows and Internet Explorer are registered trademarks of Microsoft Corporation.
3 E n Front view 2 345 1 1. LCD panel 2. Remote control sensor 3. Input switch (See page 5.) 4. Power switch 5. Power LED TIPS • Use a pointed object such as a pen tip to press the switches at the front of the monitor . Part Names n Rear view When the PN-ZB01 (optional) is attached 1 18 17 16 15 19 79 2 5 6 4 10 11 22 21 20 24 23 12 13 14 3 8 1.
E 4 Part Names n Remote control unit 1 2 3 4 5 6 9 8 7 1. Signal transmitter 2. POWER button 3. DISPLA Y button (See page 5.) 4. MUTE button (See page 5.) 5. VOL +/- buttons (See page 5.) BRIGHT +/- buttons (See page 5.) Cursor control ( / / / ) buttons 6.
5 E Basic Operation 1 2 3 4 5 6 7 8 1. INPUT (Input mode selection) The menu is displayed. Press or to select the input mode, and press to enter . * Y ou can select the input terminal by pressing the input switch of the monitor .
E 6 Basic Operation n Switching the screen size Even when the screen size is changed, the display may remain the same depending on the input signal. WIDE PC input Displays image so it lls the entire screen. A V input An image with a 4:3 aspect ratio is stretched to ll the entire screen.
7 E Menu Items Displaying the menu screen Video and audio adjustment and settings of various functions are enabled. This section describes how to use the menu items. See pages 10 to 13 for details of each menu items. Caution • Do not turn the main power switch off while the menu items are being displayed.
E 8 Menu Items List of menu items The displayed menu items vary depending on whether or not the PN-ZB01 (optional) is attached. ○: Item is available, -: Item is not available.
E 9 Menu Item PN-ZB01 (optional) Not attached Attached OPTION DA TE/TIME SETTING ○ ○ SCHEDULE ○ ○ INPUT SELECT DVI - ○ BNC - ○ HDMI ○ ○ AUDIO SELECT PC DVI-D - ○ PC HDMI ○ ○ PC D.
E 10 Menu item details The menu will differ depending on the input mode. n SCREEN AUTO (PC D-SUB/PC RGB) The CLOCK, PHASE, H-POS, and V -POS are automatically adjusted.
E 11 n AUDIO TREBLE Adjusts the volume of treble-level sound. BASS Adjusts the volume of bass-level sound. BALANCE Adjusts the balance of the audio sound between right and left. RESET Resets the values of the AUDIO menu items to the factory preset values.
E 12 Menu Items AUTO INPUT CHANGE Specify whether to change inputs automatically . When ON is selected and no signal is present in the selected input mode, AUTO INPUT CHANGE automatically changes the selected mode to another mode where a video signal is present.
E 13 Menu Items n PIP/PbyP PIP MODES Sets the display method. OFF .........Displays one screen. PIP ...........Displays a sub screen inside a main screen. PbyP ........ Displays a main screen and a sub screen in a line. PbyP2 ...... Displays a main screen which measures 1280 pixels in the longest direction and a sub screen in a line.
E 14 Menu Items n Enlarge • Y ou can align several monitors and integrate them into a single large screen to display . • Up to ve monitors can be aligned in both the horizontal and vertical directions. • Each monitor displays enlarg ed views of separated images.
E 15 n SCHEDULE Y ou can set the time to switch the monitor on and off. Set th is funct ion with “SCHEDU LE” in t he OPTIO N menu. (See page 12.) SCHEDULE No. POWER DA Y OF THE WEE KT IME INPU T XXXX/XX/XX XXX XX:XX:XX (2) OK … [MENU] 1920x1080 V: 60 Hz H: 67.
E 16 n ADV ANCED items (A V input) (See page 10 for additional Menu item details.) FLESH TONE Adjust the hue control. 3D-NR Reduce the noise of playback images on video. Setting a higher level reduces more noise. However , it may cause blurring on an image.
17 E Y ou can return the settings to their factory-preset values and restrict operations. 1. After pressing for about 5 seconds, press , , , and in that order . OFF UNLOCKED ON ON LED OFF MONI TO R FUNCTION 1/1 AL L RESET ADJUSTMENT LOCK RS-232C OSD DISPL AY LED TEMPER AT URE ALERT ST AT US ALERT POWER BUT TO N CONTROLLER INPUT END … [MENU] 2.
18 E Controlling the Monitor with a PC (RS-232C) Y ou can control this monitor from a PC via RS-232C (COM port) on the PC. Y ou can also connect multiple monitors via a daisy chain by using a PC. By assigning ID numbers to each monitor (see page 19), you can make input mode selection/adjustment or can check the status of a specic monitor .
E 19 Controlling the Monitor with a PC (RS-232C) n Response code format When a command has been executed correctly O K Return code (0D H , 0A H ) A response is returned after a command is executed.
E 20 Controlling the Monitor with a PC (RS-232C) n Commands for ID control The command examples shown on this page assume the following connection and ID number set up. ID number: 1 ID number: 2 ID number: 3 ID number: 4 IDST ......... A monitor receiving this command sets its own ID number in the parameter eld.
E 21 Controlling the Monitor with a PC (RS-232C) n Repeater control This system has a function to allow setting of multiple monitors connected in a daisy chain using a single command. This function is called repeater control. Y ou can use Repeater control function without assigning ID numbers.
E 22 RS-232C command table How to read the command table Command: Command eld (See page 18.) Direction: W When the “Parameter” is set in the parameter eld (see page 18), the command functions as described under “Control/Response Contents”.
E 23 PICTURE menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) AUTO AGIN W 1 When the input mode is PC D-SUB, PC RGB. - ○ ○ CONTRAST CONT WR 0-60 0-60 0-127 on PC D-SUB, PC RGB. ○ BLACK LEVEL BL VL WR 0-60 0-60 0-127 on PC D-SUB, PC RGB.
E 24 SETUP menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) OSD H-POSITION OSDH WR 0-100 0-100 ○ ○ ○ OSD V -POSITION OSDV WR 0-100 0-100 MONITOR (for PN-E4.
E 25 OPTION menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) DA TE/TIME SETTING DA TE WR AABBCCDDEE AABBCCDDEE AA: Y ear, BB: Month, CC: Day , DD: Time, EE: Minu.
E 26 Controlling the Monitor with a PC (RS-232C) ENLARGE menu (When the input mode is PC) Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) ENLARGE MODE EMAG WR 0-4 0-.
E 27 PIP/PbyP menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) PIP MODES MWIN WR 0-3 0-3 0: OFF , 1: PIP , 2: PbyP , 3: PbyP2 ○ ○ ○ PIP SIZE MPSZ WR 1-12 1.
E 28 Others Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) SCREEN SIZE (PC) WIDE WR 1-5 1-5 1: WIDE, 2: NORMAL, 3: Dot by Dot, 4: ZOOM1, 5: ZOOM2 ○ ○ ○ SCREEN.
29 E When the PN-ZB01 (optional) is attached, your monitor can be connected to a LAN allowing you to control it from a PC on the LAN. Y ou can also congure the monitor to send e-mail notication when it has a problem. The connection requires a commercially available LAN cable (UTP cable, Category 5, straight through).
30 E 30 ■T osetfromaPC When the monitor is connected to a PC, LAN settings can be congured via PC. Set up process (1) Connect your monitor to a PC (2) Specify the PC’s IP address.
31 E 31 5. Click on “LAN SETUP” under NETWORK. 6. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc. DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically , change this setting to “ON”. T o set the address manually , set this to “OFF”.
32 E 32 ■INFORMA TION Information about this monitor appears. ■CONTROL Y ou can control the operations corresponding to the buttons ( ) on the remote control unit.
33 E 33 ■NETWORK(LANSETUP) This screen allows you to set the settings necessary when the monitor is connected to a LAN. DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically , change this setting to “ON”.
34 E 34 ■NETWORK(GENERAL) This screen allows you to specify the general LAN settings. MONITOR NAME Specify a name for this monitor as it should appear on the Internet Explorer screen. AUTO LOGOUT TIME Specify the time (in minutes) to elapse before automatically disconnecting this monitor from the network.
35 E 35 ■MAIL(RECIPIENT) This screen allows you to specify the recipients of the e-mail sent periodically or when the monitor has an error . RECIPIENT E-MAIL ADDRESSES Specify the e-mail addresses to send error notication e-mail to. CONDITION Specify the conditions to send mails.
36 E 36 Controlling the Monitor with a PC (LAN) ■SNMP Y ou can congure settings related to SNMP . SNMP SETTING Set whether to enable or disable SNMP . VERSION Set the version of the SNMP to be supported. COMMUNITY NAME 1 to 3 Set the name of the community required for the access.
37 E T roubleshooting If you are experiencing any problem with your display , before calling for service, please review the following troubleshooting tips.
38 E Specications n ProductSpecications Model PN-E471 PN-E421 LCD component 47" Class [46-15/16 inch (1 19.3cm) diagonal] TFT LCD 42" Class [42-1/16 inch (106.7cm) diagonal] TFT LCD Max. resolution (pixels) 1920 x 1080 Max. colors Approx.
39 E Specications n Dimensional Drawings Note that the values shown are approximate values. [ PN-E471] 42-5/8 [1083] Opening width (41-1/16 [1043]) 38-1/16 [967] Opening height (23-1/8 [588]) 24-3/.
40 E Specications n Power management This monitor conforms to VESA DPMS and DVI DMPM. Both your video card and computer must support the same standard in order for the monitor ’s power management function to work.
41 E n Compatible signal timing (PC) VESA Wide US TEXT Sun Screen resolution Hsync Vsyn c D ot frequency Digital 640 × 480 800 × 600 848 × 480 1024 × 768 1 152 × 864 1280 × 768 1280 × 800 1280 .
42 E Specications n PC/A V DVI-D input terminal pins (DVI-D 24 pin) No. Function No. Function 1 TMDS data 2- 13 N.C. 2 TMDS data 2+ 14 +5V 3 TMDS data 2/4 shield 15 GND 4 N.C. 16 Hot-plug detection 5 N.C. 17 TMDS data 0- 6 DDC clock 18 TMDS data 0+ 7 DDC data 19 TMDS data 0/5 shield 8 N.
PN-E471E421 G EN10B(2).
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Sharp PN-E471 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Sharp PN-E471 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Sharp PN-E471, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Sharp PN-E471 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Sharp PN-E471, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Sharp PN-E471.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Sharp PN-E471. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Sharp PN-E471 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
