Manuel d'utilisation / d'entretien du produit DM95 du fabricant Servis-Rhino
Aller à la page of 106
DM82, DM95, DM1 12 & DM124 Disc Mower OPERA T OR'S MANUAL Published 04-14-03 Effective S/N DM82 20000- Current Part No.4909WC DISC MOWER Effective S/N DM95 20201- Current OPERA T OR'S MANUAL This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times.
TO THE OWNER/OPERA T OR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices.
In order to reduce accidents and enhance the safe operation of mowers, Alamo Gr oup Ag Division, in cooperation with other industry manufacturers has developed the AEM/FEMA Industrial and Agricultural Mower Safety Practices video and guide book.
Alamo Group Ag. Division is willing to provide one (1) AEM Mower Safety Practices V ideo Please Send Me: VHS Format – AEM/FEMA Mower Operator Safety V ideo DVD Format – AEM/FEMA Mower Operator Saf.
T ABLE OF CONTENTS SAFETY SECTION ......................................................................................................................................... 1-1 Safety Information ........................................................
When ordering parts for this manual be sure that orders for replacement parts include the following informa- tion: 1. Name of machine 2. Machine model number 3. Machine serial number (The serial number plate is located on the front of the 3-point frame) 4.
SAFETY SECTION Safety Section 1-1.
SAFETY Safety Section 1-2 DM 07-02 © 2004 Alamo Group Inc. A safe and careful operator is the best operator . Safety is of primary importance to the manufac- turer and should be to the owner/operator . Most accidents can be avoided by being aware of your equipment, your surroundings, and observing certain precautions.
SAFETY Safety Section 1-3 DM 07-02 © 2004 Alamo Group Inc. Si no lee Ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad.
SAFETY Safety Section 1-4 DM 07-02 © 2004 Alamo Group Inc. DANGER! Never allow children or other persons to ride on the Tractor or Implement. Falling off can result in serious injury or death. (SG-10) DANGER! Never allow children to operate or ride on the Tractor or Implement.
SAFETY Safety Section 1-5 DM 07-02 © 2004 Alamo Group Inc. WARNING! Transport only at safe speeds. Serious accidents and injuries can result from operating this equipment at unsafe speeds. Understand the Tractor and Implement and how it handles before transporting on streets and highways.
SAFETY Safety Section 1-6 DM 07-02 © 2004 Alamo Group Inc. DANGER! KEEP AWAY FROM ROTATING ELEMENTS to prevent entanglement and possible serious injury or death. (SG-24) DANGER! Never allow children to play on or around Tractor or Implement. Children can slip or fall off the Equipment and be injured or killed.
SAFETY Safety Section 1-7 DM 07-02 © 2004 Alamo Group Inc. DANGER! All Safety Shields, Guards and Safety devices including (but not limited to) - the Deflectors, Chain Guards, Steel Guards, Gearbox Shields, Hydraulic Tank Shields, and Retractable Door Shields should be used and main- tained in good working condition.
SAFETY Safety Section 1-8 DM 07-02 © 2004 Alamo Group Inc. DANGER! Replace bent or broken blade with new blades. NEVER ATTEMPT TO STRAIGHTEN BLADES SINCE THIS WILL LIKELY CRACK OR OTHERWISE DAMAGE THE BLADE WITH SUBSEQUENT FAILURE AND POSSIBLE SERIOUS INJURY FROM THROWN BLADES.
SAFETY Safety Section 1-9 DM 07-02 © 2004 Alamo Group Inc. WARNING! Never leave Tractor and Implemented unattended while the implement is in the lifted position. Accidental operation of lifting lever or a hydraulic failure may cause sudden drop of unit with injury or death by crushing.
SAFETY Safety Section 1-10 DM 07-02 © 2004 Alamo Group Inc. PARTS INFORMATION Servis-Rhino mowers use balanced and matched system components for blade carriers, blades, cuttershafts, knives, knife hangers, rollers, drivetrain components, and bearings.
SAFETY Safety Section 1-11 DM 07-02 © 2004 Alamo Group Inc. NOTES.
SAFETY Safety Section 1-12 DM 07-02 © 2004 Alamo Group Inc. 27 28 29 30 31 32 27 NOTE: Rhino supplies safety decals on this product to promote safe operation.
SAFETY Safety Section 1-13 DM 07-02 © 2004 Alamo Group Inc. ITEM PART NO. QTY. LEVEL DESCRIPTION 3210400 1 N/A Decal Kit - Safety (All Models) 00772628 1 N/A Decal Kit - DM82(Complete) 00772629 1 N/A.
SAFETY Safety Section 1-14 DM 07-02 © 2004 Alamo Group Inc. 1 - 00725746 5 - 00760657 4 - 00756494 6 - 02962765 16 - 000678 3 - 00756005 2 - 00756004 05-05-99.
SAFETY Safety Section 1-15 DM 07-02 © 2004 Alamo Group Inc. 8 - 3238318 9 - 3238319 11 - 999001 15 - 00763977 25 - D301 13 - 00758194 21 - 3238307 17 - 1458380 12 - 00756059 10 - 3238320 7 - 3238322 .
SAFETY Safety Section 1-16 DM 07-02 © 2004 Alamo Group Inc. 18 - 00772879 19 - 3238300 20 - 3238301 14 - 3238311 23 - 00772631 23 - 00772633 23 - 00772632 DM82 DM95 DM1 12 23 - 00772891 DM124.
SAFETY Safety Section 1-17 DM 07-02 © 2004 Alamo Group Inc. 22 - D103 26 - 2458315 27- 00776481.
SAFETY Safety Section 1-18 DM 07-02 © 2004 Alamo Group Inc. This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning employer and employee equipment operators. This section is not intended as a legal interpretation of the law and should not be considered as such.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Introduction Section 2-1 INTRODUCTION SECTION.
Introduction Section 2-2 DM 07-02 © 2004 Alamo Group Inc. INTRODUCTION This Mower is designed with care and built with quality materials by skilled workers. Proper assembly, maintenance, and operating practices, as described in this manual, will help the owner/operator get years of satisfactory service from the machine.
ASSEMBL Y SECTION Assembly Section 3-1.
ASSEMBL Y DM 07-02 © 2004 Alamo Group Inc. Assembly Section 3-2 Figure 1 Figure 2 Figure 3 CAUTION! CAUTION! 2. Attach the 3-point frame to the main frame as shown in illustration 2 using the mainframe pin and two roll pins(B). Make sure the parts are clean and well lubricated.
ASSEMBL Y DM 07-02 © 2004 Alamo Group Inc. Assembly Section 3-3 7. Install the cover frame on the cutter bar using two M16 x 35mm bolts (F), locking plate and lockwashers at the top and three M16x35mm bolts and lockwashers (G) installed on the side. (See Figure 5 .
ASSEMBL Y DM 07-02 © 2004 Alamo Group Inc. Assembly Section 3-4 9. Place the cover sheet over the assembled frame and secure the sheet in place with plastic ties through grommets around cover frame at all locations. (See Figure 7 .) DO NOT OVERTIGHTEN PLASTIC TIE.
ASSEMBL Y DM 07-02 © 2004 Alamo Group Inc. Assembly Section 3-5 14. Attach the outer support weldment to the swath board bracket and the cover frame tube as shown ( Figure 1 1&12 ).Using two M10 x 75 mm bolts and locknut s on top (O), and one M12 x 50mm bolt (N), and one M12 x 50mm carriage bolt (M).
ASSEMBL Y DM 07-02 © 2004 Alamo Group Inc. Assembly Section 3-6 Figure 14 Figure 15 16. T o check the oil level, tilt the cutter bar up 90 degrees and remove Plug(L) . Add SAE EP90 gear lube, or equivalent, at opening until oil flows from opening . Reinstall plug.
OPERA TION SECTION Operation Section 4-1.
Operation Section 4-2 OPERA TION DM 07-02 © 2004 Alamo Group Inc. The Rhino Disc Mower requires 540 RPM PTO power and is designed to mount on Category II 3-point hitch equipped tractors. Model DM82 mowers require a minimum of 40 HP for operation. Model DM95 mowers require a minimum of 45 HP .
Operation Section 4-3 OPERA TION DM 07-02 © 2004 Alamo Group Inc. 6. Lower the mower so that the center of the lower linkage arm is 16" above the ground. (See Figure 5 .) 7. Connect the Support chain (S) to the tractor's top link support bracket and adjust to maintain the ground-to- linkage height of 16" set in Step in 5.
Operation Section 4-4 OPERA TION DM 07-02 © 2004 Alamo Group Inc. 4. Cut the shield and shaft of the mower half so the same amount is removed as the tractor half. Deburr the ends, lubricate the shaft halves with grease and reassemble the halves. 5. Install the IID shaf t on the tractor and mower .
Operation Section 4-5 OPERA TION DM 07-02 © 2004 Alamo Group Inc. Adjusting Mowing Height The mowing height is adjusted by adjusting the top link of the 3-point linkage to move the forward portion of the disc up or down. (See Figure 1 1 .) IMPORT ANT : Do not allow the disc blade to cont act the ground.
Operation Section 4-6 OPERA TION DM 07-02 © 2004 Alamo Group Inc. BEL T TENSION ADJUSTMENT The belt tension must be adjusted properly to prevent the belt from slipping.
Operation Section 4-7 OPERA TION DM 07-02 © 2004 Alamo Group Inc. Swath Board The Swath Board (W) is located on the outer end of the cutter bar . The swath stick can be positioned at three settings to handle different crop conditions such as long, short or flattened crops.
Operation Section 4-8 OPERA TION DM 07-02 © 2004 Alamo Group Inc. TRANSPORTING THE MOWER 1. Make sure the stand tube is secured in the "up" position. If not, pull clip and Pin (R) and slide S tand T ube (A) up. Secure with Pin (R) and clip.
Operation Section 4-9 OPERA TION DM 07-02 © 2004 Alamo Group Inc. Figure 22 Figure 23 W ARNING! SECURE TRANSPOR T LOCK BEFORE TRANSPORTING MOWER, OTHER WISE MOWER HEAD LIFT CYLINDER MA Y LEAK DOWN RESUL TING IN POSSIBLE INJURY OR DEA TH TO BYST ANDERS.
Operation Section 4-10 OPERA TION DM 07-02 © 2004 Alamo Group Inc. DISC MOWERS ARE NOT INTENDED FOR ROADSIDE OR MUNICIP AL MOWING . THEY ARE INTENDED FOR AGRICUL TURAL USE ONL Y . DO NOT OPERA TE MOWER NEAR STRUCTURES WHICH MA Y BE VULNERABLE TO DAMAGE FROM THROWN OBJECTS.
Operation Section 4-11 OPERA TION DM 07-02 © 2004 Alamo Group Inc. ST OP MOWER IMMEDIA TEL Y IF IT BEGINS TO VIBRA TE. OPERA TING THE MOWER WITH A VIBRA TION MA Y RESUL T IN COMPONENT F AILURE. DETERMINE CAUSE OF VIBRA TION AND CORRECT . CHECK IF KNIVES ARE IN GOOD CONDITION A ND ROT A TING FREEL Y .
.
MAINTENANCE SECTION Maintenance Section 5-1.
MAINTENANCE DM 07-02 Maintenance Section 5-2 © 2004 Alamo Group Inc. BEFORE PERFORMING INSPECTIONS, MAINTENANCE, OR ADJUSTMENTS OF THE MOWER, ST O P THE TRACTOR ENGINE, REMOVE THE KEY , AND SECURE P ARKING BRAKE. W AIT FOR ALL ROT A TING MOTION OF THE MOWER TO ST OP AND DISCONNECT THE DRIVELINE SHAFT .
MAINTENANCE DM 07-02 Maintenance Section 5-3 © 2004 Alamo Group Inc. Figure 2 T o remove the disc, remove the 6 bolts (DD)( See Figure 1 ). T o remove the hub (EE), remove the locknut (FF) and the conical washer (GG). Pull the hub upward evenly to remove.
MAINTENANCE DM 07-02 Maintenance Section 5-4 © 2004 Alamo Group Inc. LUBRICA TION Both the gearbox and the cutter bar are lubricated by a seperate oil supply . T o fill the cutter bar . Raise the cutter bar up 90 degrees and remove Plug. Add SAE HD90 gear lube or equivalent until oil flows from opening.
MAINTENANCE DM 07-02 Maintenance Section 5-5 © 2004 Alamo Group Inc. GEARBOX SECTION END VIEW CUTTERBAR SECTION END VIEW Oil Filler PLug 2716591 Bolt 61367C8 Bolt 7081 10C12 Hex Nut 00756164 Bolt 708.
MAINTENANCE DM 07-02 Maintenance Section 5-6 © 2004 Alamo Group Inc. PROPER TORQUE FOR F ASTENERS Because of the severe operating conditions, correct bolt torque is very important. An improperly torqued bolt can be easily shaken loose or broken by the vibrations.
MAINTENANCE DM 07-02 Maintenance Section 5-7 © 2004 Alamo Group Inc. T o prepare your Disc Mower for storage: 1. Clean the mower of all dirt and debris. 2. Drain the oil from the cutter bar and replace with fresh SAE HD90 lube oil. (See Lubrication Instructions.
MAINTENANCE DM 07-02 Maintenance Section 5-8 © 2004 Alamo Group Inc. Disc mowers are not intended for roadside or municipal mowing. The mowers are intended for agricultural use only . Do not operate mowers near structures which may be vulnerable to damage from thrown objects.
.
LIMITED WARRANTY 1. LIMITED WARRANTIES 1.01. Servis-Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser (“Purchaser”) and warran.
To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need.
DISC MOWER-OM 07/02 Printed U.S.A. 4909WC DM82, DM95, DM1 12 & DM124 Disc Mower DISC MOWER.
SERVIS-RHINO ® 1020 S. Sangamon Ave. Gibson City, IL 60936-9907 Please fold (do not tear), tape, and drop in any mailbox. PLEASE FILL OUT OWNER W ARRANTY REGISTRA TION INFORMA TION SIGN, AND DROP LAST COPY IN ANY MAILBOX.
• I have informed the Purchaser of this product of W arranty terms, provisions, and procedures that are applicable, reviewed the contents of the Operator ’ s Manual including safety equipment, saf.
.
• I have informed the Purchaser of this product of W arranty terms, provisions, and procedures that are applicable, reviewed the contents of the Operator ’ s Manual including safety equipment, saf.
.
• I have informed the Purchaser of this product of W arranty terms, provisions, and procedures that are applicable, reviewed the contents of the Operator ’ s Manual including safety equipment, saf.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Servis-Rhino DM95 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Servis-Rhino DM95 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Servis-Rhino DM95, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Servis-Rhino DM95 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Servis-Rhino DM95, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Servis-Rhino DM95.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Servis-Rhino DM95. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Servis-Rhino DM95 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
