Manuel d'utilisation / d'entretien du produit 486.248392 du fabricant Sears
Aller à la page of 28
Owner's Manual TRACT OR A TT ACHMENT Model No. 486.248392 42"- 2 ST AGE SNOW THROWER ® PRINTED IN U.S.A. FORM NO. 48936 (REV. 7/04) Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com/craftsman CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions.
2 T ABLE OF CONTENTS MODEL NUMBER: 486.248392 SERIAL NUMBER: __________________ DATE OF PURCHASE: __________________ The model number and serial numbers will be found on a decal attached to the snow thrower. You should record both the serial number and the date of purchase and keep in a safe place for future reference.
3 SAFETY Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times, when using power equipment. • Read this owner's manual carefully and know how to operate your snow thrower and how to stop the unit and disengage the controls quickly.
4 HARDW ARE P ACKAGE CONTENTS REF. QTY. DESCRIPTION REF. QTY. DESCRIPTION T 6 Hex Lock Nut, 1/4" U 12 Hex Nut, 5/16" V 1 Whizlock Nut, 5/16" W 4 Hex Lock Nut, 5/16" (2 pcs.
5 CARTON CONTENTS 1. Cross Brace (Weight Tray) 2. Side Brace (Weight Tray) 3. Right Hand Side Plate (Stamped "R") 4. Left Hand Side Plate (Stamped "L") 5. Anti-rotation Bracket 6. Engagement Rod (Not used on some models) 7. Engine Pulley Keeper (Not used on some models) 8.
6 • Remove all parts and hardware packages from the carton. Lay out parts and hardware and identify using the illustrations on pages 4 and 5. NOTE: Not all of the supplied parts and hardware will be needed for your particular tractor. Unneeded items may be discarded after you have completed assembly.
7 • Assemble a shoulder bolt, a 3/8" lock washer and a 3/8" hex lock nut to the bottom hole in each side plate. See figure 3. • Proceed to page 8.
8 FIGURE 10 RIGHT SIDE VIEW INSTALLING HANGER BRACKETS For better clearance, lower the tractor's suspension arms using the attachment lift lever. On Tractors With Foot Rest Brackets (Figure 7) • Remove the bolt and nut that fasten the L.H. and R.
9 FIGURE 13 RIGHT SIDE VIEW INSTALLING CLUTCH/IDLER ASSEMBLY This section covers the installation of the Clutch/Idler assembly to tractors with attachment clutches that are either rod operated (p. 9), cable operated (p. 10) or electric (p. 12). Use the appropriate instructions for your tractor.
10 • Assemble the short "V" belt onto the engine pulley and then onto the large pulley on top of the clutch/ idler assembly. The belt must be placed to the inside of the engine pulley keeper, the idler pulley and the keeper bolt located beside the large pulley.
11 Hold this drawing above you while viewing the Clutch/Idler Assembly from underneath the tractor. Right and left in the drawing will be the reverse of the viewer's right and left.
12 FIGURE 20 VIEW OF BOTTOM • Attach the clutch/idler assembly to the tractor frame as follows. Hook the assembly's notched arms onto the two shoulder bolts you assembled to the inside of the tractor frame. Lift the front of the assembly and attach it to the R.
13 ASSEMBLY OF THE SNOW THROWER • Place the lift handle into the lift bracket on the right side of the snow thrower. Fasten the handle to the bracket using two 5/16" x 1-3/4" hex bolts, 5/16" lock washers and 5/16" hex nuts. See figure 23.
14 • Tilt the snow thrower back down to the ground. • Remove the nylon tie which fastens the auger drive belt to the discharge housing, leaving the belt assembled around the pulleys. • Remove the nylon tie which fastens the chute crank rod to the crank rod support tube.
15 NOTE: An a dditional person's help may be required to mount the snow thrower to the front of the tractor. • Place the tractor and snow thrower on a flat, level surface so that the tractor can be rolled forward to attach the snow blower. • Remove the Attachment Pin from the snow thrower.
16 ATTACHING WEIGHT TRAY TO TRACTOR • Loosen the top hex bolt on each side of the tractor frame at the rear. Assemble the slotted end of the side braces down onto the loosened bolts.
17 • Place the plastic keg on the weight tray and fill with approximately 75 lbs. of dry sand. • Secure the keg with the rubber tarp strap hooked into the holes in the cross brace.
18 OPERA TION KNOW YOUR SNOW THROWER Read this owner's manual and safety rules before operating your snow thrower. Compare the illustration below with your snow thrower to familiarize yourself with the various controls and their locations. CHUTE TILT HANDLE Pivots the Upper Chute up or down to control the angle and distance of discharge.
19 RAISING AND LOWERING • To raise, push down on the lift handle until the snow thrower locks in the raised transport position. • To lower, push down slightly on the lift handle and pull the trigger. With the trigger pulled, slowly lower the snow thrower until it reaches the ground.
20 SERVICE AND ADJUSTMENTS CAUTION : Before servicing or adjusting the snow thrower, shut off the engine, remove the spark plug wire(s), set the parking brake and remove the key from the tractor ignition. FIGURE 38 FIGURE 37 REPLACING AUGER BELT • Disengage the tractor's attachment clutch.
21 ADDITIONAL PARTS TO REMOVE AT END OF SEASON • Remove the clutch/idler assembly. (The two hanger brackets and the two shoulder bolts may be left attached to the tractor frame.
22 P ARTS REP AIR P ARTS FOR MODEL 486.248392 42" SNOW THROWER.
23 REP AIR P ARTS FOR MODEL 486.248392 42" SNOW THROWER REF. PART QTY. DESCRIPTION NO. NO. 1 05931 1 Housing, Bearing 2 64184 1 Housing Assembly 3 618-0616 1 Gear Assembly 4 63579 1 Chute Crank R.
24 REP AIR P ARTS FOR MODEL 486.248392 42" SNOW THROWER.
25 REF. PART QTY. DESCRIPTION NO. NO. 1 64637 1 Lift Shaft Assembly 2 710-0865 2 Hex Bolt, 1/2-13 x 1" 3 710-0367 2 Hex Bolt, 5/8-11 x 1-1/2" 4 711-0332 2 Pin, Bracket Lift 5 712-0261 2 Nut,.
26 NOTES.
27 SLOPE GUIDE (Keep this sheet in a safe place for future reference.) Use this guide to determine if a slope is safe for the operation of your tractor and snow thrower. Refer also to the instructions in your vehicle owners manual. CAUTION: DO NOT OPERATE YOUR TRACTOR AND SNOW THROWER ON A SLOPE IN EXCESS OF 10 DEGREES.
Get it fixed, at your home or ours! For repair of major brand appliances in your own home… no matter who made it, no matter who sold it! 1-800-4-MY-HOME SM Anytime, day or night (1-800-469-4663) www.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Sears 486.248392 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Sears 486.248392 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Sears 486.248392, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Sears 486.248392 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Sears 486.248392, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Sears 486.248392.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Sears 486.248392. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Sears 486.248392 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
