Manuel d'utilisation / d'entretien du produit MobileMax ST500LT032 du fabricant Seagate
Aller à la page of 32
Product Manual Seagate ® Laptop Ultrathin HDD SATA Gen 9.3 100715053 Rev. A May 2013 Standard models ST500LT032 ST320LT030 Self-Encrypting Drive models ST500LT033 ST320LT031.
© 2013 Seagate Technology LLC. All rights reserved. Publication number: 100715053, Rev. A May 2013 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A III C ONTENTS S EAGATE T ECHNOLOGY S UPPORT S ERVICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.0 I NTRODUCTION . . . . . . . . . . . . . .
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A IV F IGURES F IGURE 1T YPICAL 5V S TARTUP AND O PERATION C URRENT P ROFILE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 F IGURE 2A TTACHING SATA C ABLING . . . . . . . . . .
Seagate Laptop Ultrathin HDD SATA Product Manual, Rev. A 1 For information regarding online support and services, visit http://www.seagate.com/about/contact-us/technical-support/ Available services in.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 2 1.0 I NTRODUCTION This manual describes the functional, mechanical and interface specifications for the following Seagate ® Laptop Ultrathin HDD SATA model drives: These drives provide the following key features: 5400-RPM spindle speed.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 3 1.1 A BOUT THE S ERIAL ATA I NTERFACE The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages incl ude: Easy installation and configuration with true plug-and-play connectivity.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 4 D RIVE S PECIFICATIONS 2.0 D RIVE S PECIFICATIONS Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 5 D RIVE S PECIFICATIONS 2.1 F ORMATTED C APACITY F ORMATTED C APACITY (1) 1. One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 6 D RIVE S PECIFICATIONS 2.3 R ECORDING AND I NTERFACE T ECHNOLOGY Recording method Perpendicular Recording density 1885 Kb/in Track density 366 ktracks/in avg Areal density 690 Gb/in 2 avg Spindle speed 5400 RPM +/- 0.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 7 D RIVE S PECIFICATIONS 2.7 P OWER S PECIFICATIONS The drive receives DC power (+5V) through a native SATA power connector (refer to Figure 2 ). 2.7.1 Power consumption Power requirements for the drives are listed in the table in Table 3 .
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 8 D RIVE S PECIFICATIONS 2.7.1.1 Typical current profiles The typical 5V startup and operation current profile is shown in Figure 1 .
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 9 D RIVE S PECIFICATIONS 2.7.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 10 D RIVE S PECIFICATIONS 2.8 E NVIRONMENTAL S PECIFICATIONS This section provides the temperature, humidity, shock, and vibration specifications for Momentus drives. Ambient temperature is defined as the temperature of the environment immediately surrounding the drive.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 11 D RIVE S PECIFICATIONS 2.9 A COUSTICS Drive emission of sound is measured consistent with the ECMA-74 and its referenced standards. Testing is conducted at room temperature (approximately 25°C).
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 12 D RIVE S PECIFICATIONS 2.11 R ELIABILITY Nonrecoverable read errors 1 per 10 14 bits read, max Load/Unload (U/UL) 25°C, 50% relativ.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 13 D RIVE S PECIFICATIONS Reorient the receiving antenna. Move the device to one side or the other of the radio or TV.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 14 C ONFIGURING AND M OUNTING THE D RIVE 3.0 C ONFIGURING AND M OUNTING THE D RIVE This section contains the specifications and instructions for configuring and mounting the drive.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 15 3.3 D RIVE M OUNTING You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting h oles. Refer to Figure 3 for drive mounting dimensions.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 16 S ERIAL ATA (SATA) I NTERFACE 4.0 S ERIAL ATA (SATA) I NTERFACE These drives use the industry-standard Seri al ATA interface that supports FIS data tran sfers. It supports ATA programmed input/ output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 17 N OTES 1 All pins are in a single row, with a 1.27 mm (0.050 in) pitch. 2 The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the mating sequences are: • the ground pins P4 and P12.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 18 S ERIAL ATA (SATA) I NTERFACE Set Features EFh Set Max Address F9h Note: Individual Set Max commands are identified by the value placed in the Set Max Features register as defined to the right.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 19 S ERIAL ATA (SATA) I NTERFACE 4.3.1 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in Ta ble 7 .
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 20 S ERIAL ATA (SATA) I NTERFACE 51 PIO data-transfer cycle timing mode 0200 H 52 Retired 0200 H 53 Words 54–58, 64–70 and 88 are v.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 21 S ERIAL ATA (SATA) I NTERFACE 93 Hardware reset value (see description following this table) xxxx H 94 Auto acoustic management setting xxxx H 95 Stream Min.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 22 S ERIAL ATA (SATA) I NTERFACE Bit Word 88 0 Ultra DMA mode 0 is supported. 1 Ultra DMA mode 1 is supported. 2 Ultra DMA mode 2 is supported. 3 Ultra DMA mode 3 is supported. 4 Ultra DMA mode 4 is supported.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 23 S ERIAL ATA (SATA) I NTERFACE 4.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 24 S ERIAL ATA (SATA) I NTERFACE 4.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 25 I NDEX A acoustics 11 active mode 9 Address 18 agency certification 12 ambient temperature 6 areal density 6 ATA commands 17 Austral.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 26 I NDEX N noise 9 nominal power 6 nonoperating shock 10 nonoperating vibration 10 nonrecoverable read errors 12 O operating shock 10 .
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 27 I NDEX U UL60950-1 12 V vibration 10 voltage dips, interrupts 11 voltage tolerance 9 W warranty 12 weight 6 width 6 Write Buffer 18 .
Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000 ASIA/PACIFIC Seagate Singapore International Headquarters Pte.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Seagate MobileMax ST500LT032 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Seagate MobileMax ST500LT032 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Seagate MobileMax ST500LT032, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Seagate MobileMax ST500LT032 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Seagate MobileMax ST500LT032, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Seagate MobileMax ST500LT032.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Seagate MobileMax ST500LT032. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Seagate MobileMax ST500LT032 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
