Manuel d'utilisation / d'entretien du produit RS727LCD du fabricant Auto Page
Aller à la page of 25
1 RS - 72 7LCD PROFESSION AL 2 - WAY LCD REMOTE C AR ST ARTER & ALARM SYSTEM With Built in Temperature sensor And Serial Port Data Link OPERATION MANUAL Please register your product at: www.
2 TABLE OF CONTENTS: LCD REMOTE TRANSMITTER : A BATTERY REPLACEMENT 4 B THE REMOTE LCD ICONS WITH FUNCTION 5 C PROGRAMMING OF THE LCD REMOTE TRANSMITTER 1. Screen Lamp ON 2. Power Save Mode 3. Clear The Flash Icon and Melody Sound 4. Stop The Melody Sound.
3 L CAR LOCATOR 14 M PANIC FUNCTION 14 N TRIGGER THE SYSTEM Clear The Trigger Icons and Melody Sound Stop The Melody Sound Only Noise Abatement C ircuit 15 15 15 15 O ANTI CAR - JACKING Active Anti Ca.
4 United States and is a wholly owned subsidiary of Iwata Electric Co., of Tokyo, Japan. Iwata has been an industry leader for over 50 years, establishing a reputat ion for ingenuity in its engineering capability and innovative communication products.
5 WARNINGS: As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of. 1. Keep the transmitter out of children’s reach. 2. Do not leave anyone in the vehicle while running on remote control.
6 B. THE REMOTE LCD ICONS WITH FUNCTION: Door Lock Your vehicle doors are locked Door Unlock Your vehicle doors are unlocked and the system is Disarmed Armed Mode Your veh icle is in armed mode Valet Mode All the function shall be temporarily on hold.
7 C. PROGRAMMING OF THE LCD REMOTE TRANSMITTER: Transmitter Button Description Operation (1 second) LCD screen lamp turns o n for 5 seconds. Press and hold for 1 second 1 melody sound to confirm enters. ( 3 seconds) Timer Programming Mode. Press and hold for 3 seconds 2 - melody sounds to confirm enter.
8 6. Vibration / Melody Mode: This is useful when you are in a noisy place and it is difficult to hear the beep sound from the remote control. In this mode, the remote control vibrates itself if your security system is triggered.
9 D. CLOCK & TIMER SETTING: Transmitter Button Description Press Transmitter Button 1 Press & Hold button for 3 seconds Clock Setting (Hour) *Flash digit for adjusting for – and for + Press button once Time setting (Minute) *Fl ash digit for adjusting for – and for + 2 Press button once.
10 3. Cou nt Down Timer Setting: Example - Set the countdown timer at 2:30 1. Press & hold the button for 3 seconds, two - melodies will sound and the “Hours” digit will flash for adjustment. 2. Press the button 5 times, the LCD screen will show the icon and the “Hours” digit flashes for adjustment.
11 Trunk Release (Channel 3) Press and Hold for 2 seconds - Passive Armi ng By - pass While the system Disarmed. Activate or Turn Off The Remote Start Press twice within 3 seconds. + Channel # 4 Timer Output ( 4 ) Optional II Switching code For 2nd Car Operation .
12 F. ALARM OPERATING CONDITION: Siren / Horn Parking Light LED Doors Starter Dome Light 1. Arming 1 or 3 Chirps 1 Flash Slow Flash Locking Disable 2. Disarming 2 or 4 Chirps 2 or 3 Flashes Unlocking Turns on for 30 - second 3. Trigger Alarming Flashes Slow Flash Disable Flashes 4.
13 The vehicle doors will automatically lock after the passive arming cycle has been completed. PASSIVE ARMING BY - PASS: While the system is disarmed, Press the button twice, the system will respond with [1] chirp and LED will turn “ON”. The sec urity system will remain in this temporary state for as long as you wish.
14 2. Within 5 seconds, enter your chosen first di git code by pressing and releasing the Valet Switch. (When finished above procedures, system's siren will stop alarming, lights will stop flashing, but the vehicle can’t be started.
15 The trans mitter can be used as a remote panic switch to manually trigger the alarm in case of emergency. 1. Press and hold the button for 3 second. The alarm will immediately sound. 2. During panic mode, the normal function of this transmitter button will be di sabled.
16 “Noise Abatement Circuit” covers doors (Hood/Trunk) differently: If the alarm is triggered by an open door for six full cycles, t he doors will be bypassed until the trigger ceases. O. ANTI CAR - JACKING Warning: If you don't need the car jacking function in this alarm system, be sure to set car jacking feature “OFF”.
17 In Car Driver Paging With the ignition in the switched “off” condition, press and hold the valet switch for 2 seconds to page the driver. One chirp sound will be emitted from the vehicle and the paging melody sound will continue sounding from your Remote LCD Transmitter and th e “ ” icon will flash on the LCD screen.
18 or sun roof. ( Factory defaults setting at momentary output.) W . POWER ON MEMORY: This security system is equipped with circuitry that will allow the unit to remember its alarm state if the power is lost and then reconnected.
19 vehicle security system. It has one short “bi” sound while pressing the button of the LCD screen transceiver. REMOTE START OPERATION: A. TO REMOTE START THE VEHICLE: When you want to start your vehicle, 1. Press button once on the transmitter. 2.
20 Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down. C. TEMPORARY STOP FEATURE: This feature allows the vehicle to remain running after the key has been removed from the ignition.
21 4. Press the brake pedal to stop the veh icle running. Exit the timer start: Timer start can be exited manually as follows: 1. Make sure the remote start system is not operating the engine. 2. Turn the ignition on. The LED and parking light will flash (4) times.
22 I . DISABLING THE REMOTE START SYSTEM: (If installed) This feature allows your system’s remote start unit to be temporarily disabled to prevent the vehicle from b eing remote started accidentally. This feature is useful if the vehicle is being serviced or stored in an enclosed area.
23 indirectly from the use or presence of the equipment or parts; Consequential damages of any kind; any inability of the purchaser to use the equipment.
24 960 Knox Street Unit B, Torrance, CA 90502.
25 Tel: (310) 323 - 1800 or (800) 262 - 2527 www.autopageusa.com.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Auto Page RS727LCD c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Auto Page RS727LCD - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Auto Page RS727LCD, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Auto Page RS727LCD va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Auto Page RS727LCD, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Auto Page RS727LCD.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Auto Page RS727LCD. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Auto Page RS727LCD ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
