Manuel d'utilisation / d'entretien du produit RS-1000 du fabricant Auto Page
Aller à la page of 24
RS1000 OP 1/07 1 RS-1000 OLED PROFESSIONAL OLED 2-WAY 900 MHz. REMOTE CAR STARTER & 6 CHANNEL ALARM SYSTEM With Built-in Temperature Sensor And Serial Port Data Link OPERATION MANUAL Please register your product at: www.
RS1000 OP 1/07 2 OLED REMOTE TRANSCEIVER: A . OLED REMOTE DISPLA Y ……………………………….…..…………………………………..…………………… 4 The Remote Transceiver, XT -100 OLED B. CHARGING THE BATTERY ……….………………………………………………………………………….
RS1000 OP 1/07 3 E. TIMER STA RT …………………………………………….…………….……………………….…..…………………… 19 3 (2 or 1) Hours T imer Start Daily Timer Start Cancel the Timer Start F. TEMPERA TURE CHECK …………….
RS1000 OP 1/07 4 REMOTE TRANSCEIVER (TX) A. OLED DISPLAY B. CHARGE THE BATTERY The unit has a built-in 3.7V lithium polymer battery. If the OLED screen display low battery or the icon is flashing, your remote transceiver needs charging. Please use the included AC / USB charger to charge the battery .
RS1000 OP 1/07 5 AC Pow er Supply: The remote transceiver equipped AC POWER SUPPLY / AC ADAPTOR (Output Voltage: 4.2VDC – 5.5VDC and with same USB plug), then you can charge the battery indoors. This screen w ill be displayed w h ile the battery of the Remote Transceiver is charging.
RS1000 OP 1/07 6 While the icon is flashing. Push the button, the alert alarm time will display ed. Press button 2 to turn OFF the alert alarm timer. D. SELECT THE TRANSCEIVER’S BUTTON CONFIGURATION: 1. Spin the jog shuttle up Switch to select the transceiver button configuration.
RS1000 OP 1/07 7 E- P1- 1. “BUTTON BI” SETTING: Example : Set the “Button Bi Disable” . The unit has a short “bi” sound while pressi ng the buttons of the remote transceiver Spin down the switch to page 1. Press button 1 and it will display the previous setting.
RS1000 OP 1/07 8 E- P1- 4. “DEMO MODE”: To display the units demo mode Spin down the switch to page 1. Press button 4 to start the Demo movie. Demo movie playing. Press any Button to exit. E- P2- 1. “POWER SAVE” SETTING: Example set the “Power Save Enable”.
RS1000 OP 1/07 9 D- P3- 1. “ TIMER / CLOCK” SETTINGS: Example: set the clock to 08:20PM Spin down the switch to page 3. Press button 1 and the ”hours” digit flashes for adjusting. Press button 2 to set the ”hours” digit to “ 08 ”. This can also be done with the jog shuttle.
RS1000 OP 1/07 10 C- P3- 3. “COUNT DOWN TIMER” SETTING: Example: set the count down timer to 2:30 Note: When count down timer is triggered, press any button to stop the beeper. Spin down the switch to page 3. Press button 3 and the ”hours” digit flashes for adjusting.
RS1000 OP 1/07 11 D- P4- 1. “NAME OF TX ” SETTING: Example Set Name of Transceiver 1 to MIKE Spin down the switch to page 4. Press button 1 and the “ - ” flashes for setting. Spin down the switch to set the “ M ”. Press button 1 and the “ - ” flashes for setting.
RS1000 OP 1/07 12 D- P6- 2. SET TO DEFAULTS: Spin down the switch to page 6. Press button 4 . Press buttons 1 & 2 at same time to set the defaults. OPERATION: A. REMOTE TRANSMITTER OPERATION: Transmitter Button System Function Remark 1 Lock Doors & Arm System / Button 1 - Arm and Bypass Zone 4.
RS1000 OP 1/07 13 E. ACTIVE ARMING – LOCK & ARM: 1. Press the button on the transmitter. 2. The siren will chirp once and parking light will flash once indicating that the system is now armed. The vehicle door will lock upon arming when inte rfaced with the security system.
RS1000 OP 1/07 14 SILENT DISARMING: Spin up the switch to the page 1 and then press the “Silent Disarm” button or press the transmitter and buttons at the same time to disa rm your security system, No chirp sound will be heard, arm and disarm confirmation will be through the vehicles parking lights only.
RS1000 OP 1/07 15 transmitter to a parking attendants or a garage mechanic. When the system is in valet mode, all alarm function and remote start functions are bypassed, however the remote panic feature and remote door locks will remain operational. To use the valet mode, the system must first be disarmed.
RS1000 OP 1/07 16 Here’s how the “Noise Abatement Circuit” works: If the alarm triggers five times, each time the same sensor (zone 4) is triggered the “Noise Abatement Circui t” will interpret this pattern of triggers as false alarms.
RS1000 OP 1/07 17 P. DRIVER PAGING / LOST & FOUND This feature is useful in the ev ent that someone wants to page the driv er of the parked vehicle or you cannot find his OLED remote transceiver. Indoor Driving Paging If the ignition switch is in the “off” posit ion, press and hold the valet switch for 2 seconds to page the driver.
RS1000 OP 1/07 18 For 2-w ay OLED Remote Control Transceiv er: A maximum of four vehicle’s security systems can be controlled by this transceiver. TX1 Red Vehicle TX2 Blue Vehicle TX3 Yellow Vehicle.
RS1000 OP 1/07 19 2. Press the brake pedal. Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down. C. TEMPORARY STOP FEATURE: This feature allows the vehicle to remain running a fter the key has been removed from the ignition.
RS1000 OP 1/07 20 F. TEMPERATURE CHECK You can monitor the present indoor tem perature of the passenger compartment through the OLED screen, before coo ling or heating your vehicle. Spin up the switch to the page 4 and then press the “Monitor TEMP.” button; the in-door temperature will be shown on the OLED screen.
RS1000 OP 1/07 21 LIMITED LIFETIME WARRANTY PROVISIONS ( U.S. ,Continental U.S. and C anada Only) 1. Auto Page, Inc. WARRANTS that this new unit has been thoroughly in spected and tested at the factory prior to delivery .
RS1000 OP 1/07 22 Warning: Some batteries may contain Perchlorate What is Perchlorate? Perchlorate is both a naturally occurring and manmade contaminant increasingly found in groundwater, surface water and soil. Most perchlorate manufactured in the U.
RS1000 OP 1/07 23 [ This page left blank inte ntionally ].
RS1000 OP 1/07 24 960 Knox Street Unit B, Torrance, CA 90502 Tel: (310) 323-1800 or (800) 262-2527 www.autopageusa.com.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Auto Page RS-1000 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Auto Page RS-1000 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Auto Page RS-1000, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Auto Page RS-1000 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Auto Page RS-1000, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Auto Page RS-1000.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Auto Page RS-1000. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Auto Page RS-1000 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
