Manuel d'utilisation / d'entretien du produit RS-900 Series RS1100 Series du fabricant Runco
Aller à la page of 104
RS-900 Series RS1100 Series 1080p DLP TM Home Theater Projectors RS-900 RS-900/CineWide™ RS-900/CineWide with AutoScope™ RS1100 RS1100/CineWide™ RS1100/CineWide with AutoScope™ RS1100 Ultra RS.
.
RS-900 and RS1100 Series Inst allation/Operation Manual iii PRE L IMINAR Y TWO YEAR LIMITED WARRANTY For Projectors, Video Processors and Controllers from Runco International, LLC (“Runco”) Congra.
iv RS-900 and RS1100 Series Installation/Operation Manu al PRE L IMINAR Y THE FOREGOING DESCRIBED WARRANTIES ARE THE ONLY WARRANTIES THAT APPLY TO THE PRODUCTS.
RS-900 and RS1100 Series Inst allation/Operation Manual v PRE L IMINAR Y © Copyright 200 8 Runco Internat ional, LLC (“Run co”). This documen t contains prop rietary inform ation prote cted by copyri ght, trademark a nd other intellect ual prop erty laws.
vi RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Thank you for you r purchase of this qu ality Runco video prod uct! It has been desig ned to provide yo u with the quality of vide o that is exp ected in a home the ater.
RS-900 and RS1100 Series Inst allation/Operati on Manu al vii PRE L IMINAR Y 19. Never look directly int o the lens w hen the lamp is on. Manufacturer’s Name: Run co Internation al, LLC Manufacture .
viii RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Date of Decl aration: June 2008 NOTE: This equipment ha s been tes ted and found to comply w ith the limits fo r a Class B d igital device , pursuant to Part 15 o f the FCC Rules.
RS-900 and RS1100 Series Inst allation/Operation Manual ix PRE L IMINAR Y Table of Hazardous Substances Model Name: R S 900 S eries Presence of one of the following RoHS-regulated substances would be indicated on the table via an “O” = compliant or a “X” = non-compliant.
x RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Table of Hazardous Substances Model Name: R S 1100 S eries Presence of one of the following RoHS-regulated substances would be indicated on the table via an “O” = compliant or a “X” = non-compliant.
RS-900 and RS1100 Series Inst allation/Operation Manual xi 1 Table of Content s PRE L IMINAR Y TWO YEAR LIMITED WARRANTY ................... ................ ............. ................ ................ . iii Important S afety In s truction s .....
Table of Contents xii RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Mounting the RS-900/RS1 100 ................... ............ ............. ................ ............. .......... 30 Floor Mount ing (Upright) .......... ..
Table of Contents RS-900 and RS1100 Series Insta llation/Operation Manu al xiii PRE L IMINAR Y 5. Maintenance and Trouble s hooting .............. ............. ................ ............. ................ 69 Lamp Repla cement ................... .
Table of Contents xiv RS-900 and RS1100 Series Installation/Operation Manu al PRE L IMINAR Y Note s :.
RS-900 and RS1100 Series Inst allation/Operation Manual xv 1 Li s t of Figure s PRE L IMINAR Y 2-1. RS-900/RS1100 Front/Side/T op View .................... ................. ............ ................. ........ 5 2-2. RS-900/RS1100 Rear/Bottom/Sid e View .
List of Figures xvi RS-900 and RS1 100 Series Installation/Operation Manu al PRE L IMINAR Y 4-6. Keystone Co rrection ..... ............. ................. ............ ............. ................ ............. .......... 60 4-7. Pincushion C orrection .
RS-900 and RS1100 Series Inst allation/Operation Manual 1 PRE L IMINAR Y 1.1 About This Manual This Owner’s Manu al describes how to insta ll, set up and operate a Runco RS-900 Series or RS1100 Series DLP™ Home Thea ter Projector. T his product fam ily consists of the RS-900, RS1100 and RS1100 Ultra Proje ctors.
Introduc tion 2 RS-900 and RS1100 S eries Installation/Operation Manual PRE L IMINAR Y Graphic Convention s : These symb ols appear in n umerous plac es througho ut the manual, to emp hasize points that you mu st keep in mind to avoid proble ms with your equipment o r injury: 1.
Introd uction RS-900 and RS1100 Series Inst allation/Operation Manual 3 PRE L IMINAR Y 1.3 Description, Features and Benefits The RS-900 and RS1100 fami ly of Home Theater Proj ectors offer the a stounding pict ure quality and versatility heretofo re associated with more expensive projectors.
Introduc tion 4 RS-900 and RS1100 S eries Installation/Operation Manual PRE L IMINAR Y Key Features and Benefits The RS-900/RS110 0 offers th ese key feature s and benefits : • Native Resolution: 19.
RS-900 and RS1100 Series Inst allation/Operation Manual 5 PRE L IMINAR Y 2.1 RS-900/RS1100 at a Glance Figure 2-1 and Figure 2 -2 show the key RS-900/RS1 100 compone nts.
Controls and Functions 6 RS-900 and RS1100 S eries Installation/Operation Manual PRE L IMINAR Y 4. TEMP LED Indicates fan sta tus and internal temperature as follo ws: • Off during norm al operation • Red when internal temperatur e is too high or a fan failure occu rs 5.
Controls and Functi ons RS-900 and RS1100 Series Inst allation/Operation Manual 7 PRE L IMINAR Y Figure 2-2. R S -900/R S 1100 Rear/Bottom/ S ide View 1. RUNCO LOGO The logo can be rotated to match the projector orientation: invert ed (ceiling-mounted) or upright.
Controls and Functions 8 RS-900 and RS1100 S eries Installation/Operation Manual PRE L IMINAR Y 2.2 RS-900/RS1100 Rear Panel Figure 2-3 shows the RS-900/R S1100 rear panel. Figure 2-3. R S -900/ R S 1100 Rear Pane l 1. HDMI 1 (Digital) HDCP-compliant dig ital video in put for connec ting a DVD player or HD tuner w ith a DVI or HDMI output.
Controls and Functi ons RS-900 and RS1100 Series Inst allation/Operation Manual 9 PRE L IMINAR Y 9. 12-VOL T (2 50 mA) TRIGGER OUTPU T (3.5-mm, mini phono jac k) Connection fo r a 12-volt trig ger-controlle d device. This can be a ret ractable scre en, screen mask or the Runco CineWide with Auto Scope system.
Controls and Functions 10 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y 1. LIGHT Press to illumin ate the buttons. 2. ON / OFF Use these butto ns to turn the pr ojector on or off. 3. S our ce S election Butto n s : VID Press to select Co mposite vi deo input as the source.
Controls and Functi ons RS-900 and RS1100 Series Inst allation/Operation Manual 11 PRE L IMINAR Y 5. Picture Adju s tment Button s : BRT (Brigh tne ss ) Press to adjust black level. CONT (Contra s t) Press to adjust white level. COL (Color) Press to adjust color intensity.
Controls and Functions 12 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y 9. Picture -In-Picture (PIP) Co ntrol s : ACT Press to switch to the ac tive window in PIP mode . PIP Press to activate PIP m ode. PIP+ Press to enlarge the PIP window.
RS-900 and RS1100 Series Inst allation/Operation Manual 13 PRE L IMINAR Y 3.1 Remote Control To install batterie s in the rem ote control, push the battery cover and slide it off. Install the two AAA batteries w ith the correc t polarity a nd then replac e the cove r.
Installation 14 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y 3.2 Quick Setup Table 3-1 gives a qu ick overview of the RS-90 0/RS1100 installation pr ocess. The sections following this one provid e detailed instructions. Installation sh ould be performed by a qualified custom video installation specialist.
Installation RS-900 and RS1100 Series Inst allation/Operation Manual 15 PRE L IMINAR Y 3.3 Installation Considerations Proper installation of you r projector will ensur e the quality of yo ur display.
Installation 16 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Throw Distance Throw distance is the dista nce measured fro m the front of the projec tor to the screen.
Installation RS-900 and RS1100 Series Inst allation/Operation Manual 17 PRE L IMINAR Y Table 3-4 gives the thr ow ratios for the RS1100 Ultra. RS-900/CineWide or RS1100/CineWide (McKinley Lens) (n/a) 1.40 – 1.65 134.40 158.40 RS-900/CineWide with AutoScope or RS1100/CineWide with AutoScope (McKinley Lens) 1.
Installation 18 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Vertical and Horizontal Position Proper placem ent of the proje ctor relative t o the screen wil l yield a rectangu lar, perfectly-cen tered image that complet ely fills the scree n.
Installation RS-900 and RS1100 Series Inst allation/Operation Manual 19 PRE L IMINAR Y Figure 3-4. Horizontal Le n s S hift (Example O nly) 0% Screen Center 100% Width Lens Shift (1.0 x W) 50% Width Lens Shift (0.5 x W) Screen Width (W) Note: This is a general example of lens shift.
Installation 20 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Table 3-5 li sts the lens shift l imits for each available RS-900/RS11 00 lens, as pe rcentages and absolu te measur ements with a 100 x 56 inch (1.78:1) screen. Table 3-5.
Installation RS-900 and RS1100 Series Inst allation/Operation Manual 21 PRE L IMINAR Y Folded Optics In rear-screen applications wh ere space be hind the project or is limited, a m irror may be used to fold th e optical path , as shown in Figu re 3-5 .
Installation 22 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Installing the AutoScope Lens Motor Figure 3-6 shows the RS-900/Cin eWide with Aut oScope or RS1100 /CineWide with AutoScope motor assembly.
Installation RS-900 and RS1100 Series Inst allation/Operation Manual 23 PRE L IMINAR Y Figure 3-7 sh ows the RS1100 Ultra/Cin eWide with AutoScope mo tor assembly.
Installation 24 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y In s tall Ceiling Mount Adapter s /Projecto r S tand s : For ceiling installations, these brackets brin g the moun.
Installation RS-900 and RS1100 Series Inst allation/Operation Manual 25 PRE L IMINAR Y In s tall Len s Motor: 1. Position th e AutoScope Lens Motor (item #2) as shown in Figure 3-9 . 2. Line up the moun ting holes on the lens motor housing with those on th e underside of the projecto r.
Installation 26 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Installing the Fixed CineWide Base Plate (Prismatic Lens) To install the fixe d CineWide ba se plate on a n RS-900/CineWid e, RS1100/CineWide o r RS1100 Ultra/CineWide with a pri s matic anamorphic lens: 1.
Installation RS-900 and RS1100 Series Inst allation/Operation Manual 27 PRE L IMINAR Y Figure 3-10. Projector with Whitney (Pri s matic ) Len s Ba s e Plate and Ceiling Mounting Plate - Bottom View W .
Installation 28 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Installing the Fixed CineWide Base Plate (Cylindrical Lens) Figure 3-11 sh ows the cylindr ical (Rainier II/McKinley) lens b ase plate asse mbly for an RS-900/CineWide or RS1100/CineWide.
Installation RS-900 and RS1100 Series Inst allation/Operation Manual 29 PRE L IMINAR Y Figure 3-12 sh ows the RS110 0 Ultra/CineWide cylindrical (Rainier II/ McKinley) lens base plate assemb ly.
Installation 30 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y 1. Place the projector up side down on a blanket or other sof t surface. 2. Install a nylon spac er (item #3) at ea ch mounting ho le location. 3. Place the CineWide base p late (item #2) on the botto m of the pr ojector.
Installation RS-900 and RS1100 Series Inst allation/Operation Manual 31 PRE L IMINAR Y For a floor in stallation, turn t he four adjustab le feet on the b ottom of th e projector to adjust the projecto r height an d/or projec tion angle.
Installation 32 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y HDMI/DVI Connection s : See Figure 3-13. With an HDMI s ource, use the in cluded HDMI-to-HDMI ca ble; with a DVI source , use the includ ed DVI-to-HDM I cable. Figure 3-13.
Installation RS-900 and RS1100 Series Inst allation/Operation Manual 33 PRE L IMINAR Y RGB Connection s : Co nnect your per sonal comp uter or other RGB source ( DVD player or HD set top box) to the COMP 2/RGB input; see Figure 3-14 . You can use the included DB15HD-to-5 x BN C cable if your RGB s ource has a 15 -pin, VGA-type conne ctor.
Installation 34 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Compo s ite/ S -Video/Component Video Co nnection s : Use the included ca bles to connect you r composit e, S-Video and component video sources to the RS-9 00/RS1100 as shown in Figure 3-16 .
Installation RS-900 and RS1100 Series Inst allation/Operation Manual 35 PRE L IMINAR Y RS-232 Controller Connection Use the communicat ion cable sup plied with th e projector t o connect a P C or home theater control/ automation syste m (if present) to the RS-23 2 port on the RS-900/ RS1100; see Figure 3-17 .
Installation 36 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Connecting 12-Volt Trigger Output to External Theater Equipment If you are in stalling an RS-900/CineWide with Aut.
Installation RS-900 and RS1100 Series Inst allation/Operation Manual 37 PRE L IMINAR Y Connecting to AC Power Projector: The RS-900/RS1 100 ships with various types of AC power cord s. Choose t he one that is appropriate t o your locale. Plug the female end of the p ower cord into th e AC recept acle on the rear of the projector (AC 10 0V ~ 240V).
Installation 38 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y 3.8 Primary Lens Adjustments The RS-900/RS11 00 gives you a great deal of cont rol over the picture size, position and focus. Focus and Zoom – RS-900/RS1100 To focus the projected image, gras p the lens b y the oute r ring and ro tate it.
Installation RS-900 and RS1100 Series Inst allation/Operation Manual 39 PRE L IMINAR Y 3.10 Adjusting the Picture Orientation By default, the RS-900/RS110 0 is config ured for a “floor/front” in stallation, in which the projector is ins talled upright a nd in front o f the screen.
Installation 40 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Cylindrical Anamorphic Lens Installation and Adjustment The Cylindrical Anamorph ic lens mount kit consists of eve rything shown in Figure 3-20. Some compon ents shipped w ith your projec tor may differ slightly from what is shown in these instructions.
Installation RS-900 and RS1100 Series Inst allation/Operation Manual 41 PRE L IMINAR Y 5. Use the H eight/Y Adjustmen t T-Screws/Was hers (item #3), Pitc h Adjustmen t T-Screws/Wash ers (item #4) and T-Nuts (item #9) to attach the Pitch Adjustm ent Yoke and Lens Adapter Ring t o the Anamorph ic Lens Holder .
Installation 42 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y 6. Select the Cinema or Virtu al Cinema aspe ct ratio to move the an amorphic lens into position, if it isn’t already. To do this, press CINEMA or VCINE on the RS-900/RS1100 remote con trol ( Figure 2-4 ).
Installation RS-900 and RS1100 Series Inst allation/Operation Manual 43 PRE L IMINAR Y Adju s ting the Pitch (Angle): Next, angle the lens to ev en out any top-to-bottom pincushion disto rtion.
Installation 44 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Once the pr oper lens ang le has been set, firml y tighten the Yaw /X-Adjustmen t Levers to secure the lens in pl ace. Geometry: 1. Input an anamorph ic cross-hatch test patte rn to the projector.
Installation RS-900 and RS1100 Series Inst allation/Operation Manual 45 PRE L IMINAR Y Whitney (Prismat ic) Anamorphic Lens Installation and Adjustment The Whitney Anam orphic lens mo unt kit consists o f everything shown in Figure 3 -22. Some compone nts shipped with your projector ma y differ slightly from what is shown in these instructions.
Installation 46 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Adju s ting the Len s Height (Y): 1. Project a white f ield on the scre en. 2. Ensure th at the four H eight (Y) Ad justment Sc rews are loos e enough to allow vertica l movement of t he lens assembly.
Installation RS-900 and RS1100 Series Inst allation/Operation Manual 47 PRE L IMINAR Y Adju s ting the Yaw: Loosen the Yaw/Z-Adjus tment Knobs to allow the lens t o pivot freely from side to side.
Installation 48 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Note s :.
RS-900 and RS1100 Series Inst allation/Operation Manual 49 PRE L IMINAR Y 4.1 Selecting Video Memory • Press the CU S T1 or CU S T2 button on the remote con trol to recall settin gs for the cu rrent input from the “Custom 1” or “Custom 2” memory preset.
Operation 50 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y 4.5 Using Picture-In-Picture (PIP) For PIP purpos es, there are tw o groups o f inputs separated by th eir displa y modes: •V i d e o ( S D) group: Video and S-Video inpu ts.
Operation RS-900 and RS1100 Series Inst allation/Operation Manual 51 PRE L IMINAR Y Figure 4-1. R S -900/R S 1100 O S D Men u S tructure S etup Lamp Power 170W or 200W Lamp Hours View / Reset Fan Mode Normal, Hi. Alti tude or Manual Speed (if Manu al mode is selected) Background C olor Black, Blue o r Gray PIP On / Off RVR 0, 1, 2 .
Operation 52 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Main Menu The Main Menu is the starting point for accessing all project or functions. (You must ente r a passcode to access th e Setup and ISF menus.) Source Select Choose Source Sele ct from the Main Me nu to switch vi deo sources.
Operation RS-900 and RS1100 Series Inst allation/Operation Manual 53 PRE L IMINAR Y Picture Memory: For each input , the RS-900/ RS1100 le ts you store p icture qua lity settings as pre sets that yo u can recall at a later time .
Operation 54 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Select Brightness from the Pic ture Adjust menu and press ENTER . Adjust the level so that: • The darkest bla ck bars disappea r into the back ground. • The dark gray areas a re barely visible .
Operation RS-900 and RS1100 Series Inst allation/Operation Manual 55 PRE L IMINAR Y Color: On your extern al test pattern so urce, select a color bar pat tern like the on e shown in Figure 4-4 . Figure 4-4. Typical Color Bar Pattern for Adju s ting Color S aturation and Tint Select Color from the Pictur e Adjust menu and press ENTER .
Operation 56 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y S harpne ss : “Sharpness” is th e amount of high-frequen cy detail in the im age. To adjust sharpness, select Sharpness from the Picture Adjust menu and press ENTER .
Operation RS-900 and RS1100 Series Inst allation/Operation Manual 57 PRE L IMINAR Y Aspect Ratio To change the aspect ratio (size and shape) of the p rojected im age, select Aspect Rati o from the Ma in Menu an d press ENTER .
Operation 58 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y VirtualWide VWIDE VirtualWide scales a 4:3 image NON-linearly (more on the sides than in the center) to fit a 16:9 screen. On a 2.35:1 screen, the image is centere d between black bars on either side.
Operation RS-900 and RS1100 Series Inst allation/Operation Manual 59 PRE L IMINAR Y Installation To access the Instal lati on adjustments, press MENU , then press the or button to highlight Installation and press ENT ER . The Installation sub- menu appears.
Operation 60 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y GeoCorrection: Projector placemen t and other fa ctors can ca use geomet ric distortion in the projecte d image. To c orrect this, se lect GeoCorrection from the Installation menu.
Operation RS-900 and RS1100 Series Inst allation/Operation Manual 61 PRE L IMINAR Y • Pincu s hion: “Pincushion” distortion can sometimes occur if the throw dista nce is very short and/or the projector is equipped with an anamorphi c lens (refer to Installing and Adjusting the CineWide Anamorphic Lens in Section 3).
Operation 62 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Over s can: Overscan pushes the outside edge of the active picture area of th e video signal out beyo nd the edge o f the display area.
Operation RS-900 and RS1100 Series Inst allation/Operation Manual 63 PRE L IMINAR Y Information Select Informat ion from the Main Menu to see proje ctor status info rmation: the currently-act ive source, input sign al resolution, asp ect ratio, picture mem ory and lamp usage.
Operation 64 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y RVR: Use the RVR co ntrol to incre ase or decr ease the Refle ctance Volume Regulation setting. RVR lets you c ontrol the ap erture or iris size (the physica l opening th rough the lens; similar to a n “f-stop” on a cam era).
Operation RS-900 and RS1100 Series Inst allation/Operation Manual 65 PRE L IMINAR Y ISF To access the ISF Calibratio n menu, sele ct ISF from th e Main Menu and press ENTER . Use the numb er buttons o n the remot e control to en ter the ISF C alibration menu passcode when prompted and press ENTER again.
Operation 66 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Advanced Option s : For more precise contro l over picture quality, select Ad vanced Options from the ISF menu and press ENTER . • Image Enhance: The Image Enhance me nu gives you options for impr oving th e quality of standar d-definition , 480i images.
Operation RS-900 and RS1100 Series Inst allation/Operation Manual 67 PRE L IMINAR Y • Advanced Color Enhance (ACE): Use the Advanced Color Enhance (ACE) controls to customize th e stored color space charact eristics. To do t his, use the or button to select a component color (Red, Gree n, Blue, Yellow , Cyan or M agenta).
Operation 68 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Changing eithe r or both o f these num bers chang es the hue of the color and relocates the “triangle” f or possible colo rs.
RS-900 and RS1100 Series Inst allation/Operation Manual 69 PRE L IMINAR Y 5.1 Lamp Replacement The lamp should be repl aced when it reaches the e nd of its lif e (typically 20 00 hours), or sooner if a no ticeable degr adation in b rightness occ urs. Conta ct your Runco dealer to obtain a repl acement lamp.
Maintenance and Troublesh ooting 70 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y 5.2 Troubleshooting Tips Table 5-1 provide s some general guideline s for troubleshootin g problems you may encounter with the RS-900/R S1100.
Maintenance and Troubleshooting RS-900 and RS1100 Series Inst allation/Operation Manual 71 PRE L IMINAR Y LAMP LED ligh ts solid red. • The lamp has failed or exceeded its usage life. • Replace the lam p with a new one. TEMP LED lights solid red. • RS-900/RS1100 internal temperature is too high or one or more fans have failed.
Maintenance and Troublesh ooting 72 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y Note s :.
RS-900 and RS1100 Series Inst allation/Operation Manual 73 PRE L IMINAR Y 6.1 RS-232 Connection and Port Configuration To interface the RS-900/RS1100 with a home theater automation/control system or a PC running te rminal emula tion software: 1. Connect it to yo ur control system or PC as shown in Figure 3-17 .
Serial Communications 74 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y X006X Up (arrow key) X007X Down (arrow key) X008X Left (arrow key) X009X Right (arrow key) X011X Show act.
Serial Communications RS-900 and RS1100 Series Inst allation/Operation Manual 75 PRE L IMINAR Y X065X Cinema aspect ratio X066X Virtual Cinema aspect ratio X082X Image orientation = floor front X083X .
Serial Communications 76 RS-900 and RS1100 Series Installation/Operation Manual PRE L IMINAR Y X180X Blue Image ON X181X Blue Image OFF Table 6-1. S erial Command s (continued) Code Function.
RS-900 and RS1100 Series Inst allation/Operation Manual 77 PRE L IMINAR Y 7.1 RS-900/RS1100 Specifications Table 7-1 lists the RS-900 /RS1100 specificat ions.
Specifications 78 RS-900 and RS1100 Series Installation/Operation Manual P RELI M INARY Brightne ss and Contra s t: Cin ema S tandard s Mea s urement S y s tem (C S M S ) S pecification s – R S -900 S erie s - Brigh tness*: 13.
Specifications RS-900 and RS1100 Series Inst allation/Operation Manual 79 PRE L IMINAR Y +12V Output: Max. 0.25 Amps, active when Cinema or V irtual Cinema Aspect Ratio is selected (Cin eWide versions only) or wh en projector is turned on; Tip = +12 V; Sleeve = Grou nd Power Requirement s : 100 to 240 VAC (auto-sensing), 50/60 Hz, 290 Watts (989.
Specifications 80 RS-900 and RS1100 Series Installation/Operation Manual P RELI M INARY 7.2 Overall Dimensions – RS-900/CineWide and RS1100/CineWide Figure 7-1 shows the RS-900/RS1100 dimensions (all di mensions are in inc hes). Figure 7-1. Overall Dimen s ion s – R S -900/CineWide and R S 1100/CineWide (Pri s matic Len s ) 0 9.
Specifications RS-900 and RS1100 Series Inst allation/Operation Manual 81 PRE L IMINAR Y 7.3 Overall Dimensions – RS1100 Ultra Figure 7-2 sh ows the RS1100 Ultra dimensio ns (all dime nsions are in inches). Figure 7-2. Overall Dimen s ion s – R S 1100 Ultra 0 9.
Specifications 82 RS-900 and RS1100 Series Installation/Operation Manual P RELI M INARY 7.4 Overall Dimensions – RS-900/CineWide with AutoScope and RS1100/CineWide with AutoScope Figure 7-3 sh ows the RS-900/RS110 0/CineWide with AutoScope dime nsions (all dimensions are in inches).
Specifications RS-900 and RS1100 Series Inst allation/Operation Manual 83 PRE L IMINAR Y 7.5 Supported Timings Table 7-2 lists the signal types suppo rted by each inp ut on the RS-900/RS110 0.
Specifications 84 RS-900 and RS1100 Series Installation/Operation Manual P RELI M INARY 1400x1050 1400x1050 60.00 64.744 101.000 60.00 65.317 121.750 75.00 82.278 156.000 1440x900 1440x900 60.00 55.469 88.7 50 60.00 59.935 106.500 75.00 70.635 136.750 85.
Specifications RS-900 and RS1100 Series Inst allation/Operation Manual 85 PRE L IMINAR Y S DTV S ignal s (Video / S -Video) NTSC 3.58 – 59.94/60.00 15.734/15.750 3.580 NTSC 4.43 – 59.94/60.00 15.734/15.750 4.430 PAL-B/G – 50.00 15.625 4.430 PAL-M – 59.
Specifications 86 RS-900 and RS1100 Series Installation/Operation Manual P RELI M INARY Note s :.
.
Runco International • (800) 23RUNCO • Fax (503) 748-8161 • www.runco.com SERIAL NUMBER 020-0706-03 Rev. A June 2008.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Runco RS-900 Series RS1100 Series c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Runco RS-900 Series RS1100 Series - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Runco RS-900 Series RS1100 Series, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Runco RS-900 Series RS1100 Series va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Runco RS-900 Series RS1100 Series, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Runco RS-900 Series RS1100 Series.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Runco RS-900 Series RS1100 Series. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Runco RS-900 Series RS1100 Series ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.