Manuel d'utilisation / d'entretien du produit M6707-1-1 du fabricant Roper
Aller à la page of 56
SUPER PRO GUN & SUPER PRO GUN II Maintenance & Repair Manual MAGNUM VENUS PRODUCTS SUPER PRO GUN & SUPER PRO GUN II Part No. M6707-1-1 Revision 04.
SUPER PRO GUN & SUPER PRO GUN II © 2001 Magnum V enus Products Manual Part No: M6707-1-1 Corporate HQ & Mfg. Phone: (727) 573-2955 Fax: (727) 571-3636 Email: info@magind.
SUPER PRO GUN & SUPER PRO GUN II T able of Content s CHAPTER 1 - ASSEMBL Y INSTRUCTIONS Assembly Instructions for Super Pro Gun II Actuator Assembly Instructions for Super Pro Gun II Handle CHAPTE.
SUPER PRO GUN & SUPER PRO GUN II NOTE T o order the correct repair kit, refer to the gun handle before ordering part s. SUPER PRO GUN Rep air Kit NOTE A T urbulent Mixer is not used in FIT™ configurations.
SUPER PRO GUN & SUPER PRO GUN II SUPER PRO GUN II Rep air Kit NOTE The Super Pro Gun II is identified by either the blue handle or (on earlier versions) by the #2 stamped on the handle side.
SUPER PRO GUN & SUPER PRO GUN II SUPER PRO GUN Actuator Assembly 5106-01-01 1 . Install the 7301-3-020 (O-Ring) onto the 5106-7-1 (Actuator Piston) and the two 5106-4-1 (Cylinder Caps) 2 . Using 6706-3-1 (Pro Gun Oil), lightly coat the Inside of the 5106-1-01 (Cylinder Body) and the 5106-7-1 (Actuator Piston).
SUPER PRO GUN & SUPER PRO GUN II NOTE The Piston should be inserted “bushing end first”, with the bushing on the top side of center . 5 . Install the two 5106-4-1 (Cylinder Caps). 6 . Place the 5106-2-1 (Actuator Seal) over the 5106-1-01 (Cylinder Body) so the Mounting screw holes line up.
SUPER PRO GUN & SUPER PRO GUN II NOTE When installing the T rigger Assembly the 5105-8-1 (T rigger Lock) must be in the “down” position. SUPER PRO GUN Handle Assembly 5105-00-01 3 Chapter 2 1 . Carefully install the 5105-9-1 (T rigger Nut Seal) over the 5105-10-1 (T rigger Nut).
SUPER PRO GUN & SUPER PRO GUN II 4 NOTE The slot in the side of the 5105-5-1 (Porting Plate) must line up with the slot in the 5105-1-1 (Gun Handle). 5 . Set the 9203-2-1 (Compression Spring) into the spring seat located in the upper cavity of the 5105-1-1 (Gun Handle).
SUPER PRO GUN & SUPER PRO GUN II 3 . Screw the 5105-10-1 (T rigger Nut) into the 51 10-7-1 (Gun Handle) and tighten. Coat the 5110-4-1 (trigger stem) with 6706-3-1 (Pro Gun Oil) and install from the inside cavity of the 5110-7-1 (Gun Handle) through the 5105-10-1 (trigger nut).
SUPER PRO GUN & SUPER PRO GUN II 9 . Set the 5105-6-1 (T oggle W asher) into the washer seal seat of the 51 10-1-1 (Porting Plate) large side down. 10. Set the 5110-6-1 (Cylinder Gasket) over the screws, matching the slots in the 51 10-1-1 (Porting Plate) 11.
SUPER PRO GUN & SUPER PRO GUN II 7 SUPER PRO GUN Gun Block Assembly 5104-00-01 Chapter 3 1 . Install the 7301-1 1-008 (O-Ring) onto the 5104-25-1(Flush V alve Button). 2 . Install the 7301-3-007 (O-Ring) onto the 5104-23-1 (Flush Seal Body). 3 . Install the 9203-2-3 (Compression Spring) into the 5104-24-1 (Flush V alve Body).
SUPER PRO GUN & SUPER PRO GUN II 8 1 . Check for and remove debris and burrs in 5104-1-1 (Gun Block). 2 . Install the two 5104-3-1 (Secondary Seals) in the 5104-1-1 (Gun Block). See Fig. 3.1 3 . Install the 5104-10-1 (Center Spacer) into the center area of the 5104-1-1 (Gun Block).
SUPER PRO GUN & SUPER PRO GUN II 7 . Press firmly , or tap with a hammer until the seal assembly bottoms out in the 5104-1-1 (Gun Block), then gently remove the Seal Installation T ool. 8 . Hold the 9301-4-1 (Catalyst Seal Alignment T ool) firmly with a p air of pliers.
SUPER PRO GUN & SUPER PRO GUN II 14. Press firmly , or tap with a hammer until the seal assembly bottoms out in the 5104-1-1 (Gun Block), then gently remove the Seal Alignment T ool. 15. Hold the 9301-4-2 (Resin Seal Alignment T ool) firmly with a p air of pliers.
SUPER PRO GUN & SUPER PRO GUN II Fig. 3.6 18. Install the 5104-2-1 (V alve Rod) through the resin side of the gun. Use the 9301-5-1 (Seal Installation T ool) to center the V alve Rod in the 5104-1-1 (Gun Block). 19. Install and hand tighten the 5104-8-1 (Packing Nut) onto the resin side of the 5401-1-1 (Gun Block).
SUPER PRO GUN & SUPER PRO GUN II 20. Install the 5104-1 1-1 (Actuating S tem) into the 5104-2-1 (V alve Rod). 21. Actuate the 5104-1 1-1 (V alve S tem) back and forth 3 or 4 times, then snug both 5104-8-1 (Packing Nuts) with 9301-2-3 (Packing Bit) until firm.
SUPER PRO GUN & SUPER PRO GUN II Fig. 3.8 27. Position the 5104-12-1 (Mix Housing Seal) onto the backside of the 5104-20-1 (Mix Housing). See Fig. 3.8. 28. Using the two 7102-1-6 (Socket Head Cap Screws), mount the 5104-20-1 (Mix Housing) onto the 5104-1-1 (Gun Block).
SUPER PRO GUN & SUPER PRO GUN II Chapter 4 SUPER PRO GUN SuperCutter Assembly 5101-01-01 NOTE The sharp edge of the Chopper Blades should be slightly dulled by stropping them on cardboard prior to installation into Rotor Assembly .
SUPER PRO GUN & SUPER PRO GUN II Rotor Assembly 1 . Insert 9210-1-1 (Chopper Blades) between the 5103-28-1 (Rotor Hub) and 5103-29-1 (Wedge Insert). The back edge of the Blade must be bottomed against the Rotor Hub. See Fig. 4.2. 2 . Align the edges of the blade with the end of the 5103-28-1 (Rotor Hub).
SUPER PRO GUN & SUPER PRO GUN II Fig. 4.4 Fig. 4.3 Rubber Roll Assembly 5 . Press the 5103-6-1 (Rubber Roll) onto the 5103-5-01 (Mandrel Assembly). Secure the Rubber Roll by inserting the 7205-3-31 (E-Ring) into the groove in the Mandrel. See Fig.
SUPER PRO GUN & SUPER PRO GUN II 7 . Slide Rubber Roll Assembly toward the 5103-03-01 (Wedge Rotor Assembly) and tighten the 7102-2-20 (Socket Head Cap Screw) Rubber Roll Adjustment 1 . Slightly loosen the 7102-2-20 (Socket Head Cap Screw), just enough so the Rubber Roll Assembly will slide in the T -Slot.
SUPER PRO GUN & SUPER PRO GUN II NOTE Proper adjustment has Idler Assembly touching the Rubber Roll, but still able to rotate with minimum effort. Fig. 4.7 Idler Adjustment 1 . Slightly loosen the 7102-2-20 (Socket Head Cap Screw), just enough so the Idler Assembly will slide in the T -Slot.
SUPER PRO GUN & SUPER PRO GUN II 19 Chapter 5 SUPER PRO GUN Actuator Disassembly 5106-01-01 1 . Unscrew the two 5105-13-1 (Rear Screws), and the two 5105-12-1 (Front Screws) to remove the 5106-00-01 (Cylinder Body Assembly) from the 5105-00-01 (Gun Handle Assembly).
SUPER PRO GUN & SUPER PRO GUN II 20 Chapter 6 SUPER PRO GUN Handle Disassembly 5105-00-01 1 . Remove and discard the 5105-7-1 (Cylinder Gasket), and the 5105-6-1(T oggle W asher) from the 5105-5-1 (Porting Plate). 2 . Remove the 5105-5-1 (Porting Plate) from the 5105-1-1 (Gun Handle).
SUPER PRO GUN & SUPER PRO GUN II NOTE Discard all parts to be replaced by repair kit. All remaining parts should be thoroughly cleaned, inspected for damage, and replaced if necessary .
SUPER PRO GUN & SUPER PRO GUN II SUPER PRO GUN Gun Block Disassembly 5104-00-01 22 Chapter 7 1 . Remove the four 5106-6-1 (Mounting Screws), and the four 5106-3-1 (Mounting Seals) to remove the 5104-00-01 (Gun Block Assembly) from the 5106-00-01 (Gun Actuator Assembly).
SUPER PRO GUN & SUPER PRO GUN II 23 NOTE Discard all parts to be replaced by repair kit. All remaining parts should be thoroughly cleaned, inspected for damage, and replaced if necessary .
SUPER PRO GUN & SUPER PRO GUN II Chapter 8 SUPER PRO GUN SuperCutter Disassembly 5103-00-01 1 . Unscrew the 5103-14-1 (Cover Nut) and remove the 5103-13-1 (Chopper Cover) from the 5103-00-01 (Roving Cutter Basic Assembly). The remainder of the disassembly covered in this manual pertains to the rubber roll and the rotor .
SUPER PRO GUN & SUPER PRO GUN II Rotor Disassembly 4 . Loosen the two 7102-14-6 (Socket Cup Point Set Screws), and slide the 5103-03-01 (8-Blade Rotor Assembly) off of the 8402-1-1 (Air Motor) shaft.
SUPER PRO GUN & SUPER PRO GUN II SUPER PRO GUN & SUPER PRO GUN II Assembly Drawings Chapter 9 26.
SUPER PRO GUN & SUPER PRO GUN II 27 Fig. 9.1.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.2 28.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.3 29 SUPER PRO GUN.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.4 30.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.5 31 SUPER PRO GUN II.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.6 32.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.7 33.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.8 34.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.9 35.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.10 36.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.11 37.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.12 38.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.13 39 NOTE These wedge rotors will not fit on the old style “classic” pro gun choppers (58605-1). They are for SuperPro and SuperPro II chopper configurations. Please use the following part numbers for rotors: 77730-1 (6 blade) or 77731-1 (8 blade).
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.14 40.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.15 41.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.16 42.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.17 43.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.18 44.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.19 45.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.20 46.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.21 47.
SUPER PRO GUN & SUPER PRO GUN II Fig. 9.22 48.
SUPER PRO GUN & SUPER PRO GUN II.
SUPER PRO GUN & SUPER PRO GUN II.
SUPER PRO GUN & SUPER PRO GUN II © 2003 Magnum V enus Products Manual Part No: PRO-MGS-22 Corporate HQ & Mfg. 5148 1 13th Ave. Clearwater , FL 33760 · USA Phone: (727) 573-2955 Fax: (727) 571-3636 Manufacturing/Sales 1862 Ives Ave. Kent, W A 98032 · USA Phone: (253) 854-2660 (800) 448-6035 Fax: (253) 854-1666 Email: info@mvpind.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Roper M6707-1-1 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Roper M6707-1-1 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Roper M6707-1-1, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Roper M6707-1-1 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Roper M6707-1-1, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Roper M6707-1-1.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Roper M6707-1-1. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Roper M6707-1-1 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.