Manuel d'utilisation / d'entretien du produit TU-400 du fabricant Roland
Aller à la page of 21
USER'S MANUAL Thank you very much for purchasing the automatic media take-up unit. • To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read through this manual completely and store it in a safe location.
ROLAND DG CORPORA TION 1-6-4 Shinmiyakoda, Hamamatsu-shi, Shizuoka-ken, JAP AN 431-2103 MODEL NAME : See the MODEL given on the rating plate. RELEV ANT DIRECTIVE : EC MACHINER Y DIRECTIVE (89/392/EEC).
1 In this manual, the following conventions are used to refer to different models that have items in common. TU-60/70 .............. TU-60 and TU-70 CJ .................... CJ-500 and CJ-400 TU-400/500 .......... TU-400 and TU-500 FJ .................
2 T o Ensure Safe Use Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly . About and Notices Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly .
3 Installation of the control box for the TU is a task which must be carried out by two or more persons. Injury may result if attempted by one person without assistance. To secure the part in place, use the bolt included with the unit. A loose bolt or use of other than the specified bolt may result in the falling of the part, leading to injury .
4 Do not strike the mirror . Doing so may damage the mirror , resulting in incorrect operation. About the Labels Affixed to the Unit These labels are affixed to the parts shown below . The following figure describes the location. Rating label Use a rated power supply .
5 TUC-60/70 1. System Configuration Use with the configuration shown below . 2. Confirmation of Included Items The items are in the two packing cartons.
6 Frame and Control Box Installation 3. Installation and Assembly Required tool Large Installation of the control box is a task which must be carried out by two or more persons. Injury may result if attempted by one person without assistance. To secure the part in place, use the bolt included with the unit.
7 (1) (2) Rail Slider Installation Follow steps (1) and (2) in sequence to install the rail slider . Required tool Small Front Required tool Small Installing the Sensor and the Small Retainer If the screw holes for the small cap screws do not line up, loosen all screws at the locations shown in the figure.
8 Power Cord Connection and Large Retainer Installation Arm Installation The configuration of the AC adapter varies according to regional differences in voltage.
9 5. Adjusting the Sensor's Position T urn on the power . T wo LEDs (green and red) light up. 1 Loosen the screw as shown in the figure, and adjust the angle of the sensor so that it is aligned with the mirror . 2 T ighten the adjustment screw securely at the angle where the red LED has gone dark.
10 Return of pulled-out material Material feed Take-up of fed material The CJ/FJ stops operation Take-up of fed material MOTOR ERROR TURN OFF POWER 6. Operating Conditions for the TU The TU takes up material fed from the CJ/FJ.
11 Mounting the Flange and Paper T ube When using the core from used-up rolled material as the paper tube When mounting the paper tube on the flanges, make sure that the paper tube fits snugly . Attempting to take up material when the paper tube is not stable may cause problems such as the pa- per tube coming loose.
12 25 mm (1 in.) or more 25 mm (1 in.) or more FJ T o ensure correct feed, make sure the material pulled out from the roll is free of slack. [Correct] FJ rear [Incorrect] FJ rear Entire material stretched taut Material is slack Loading Rolled Material * For more information, see the user's manual for the CJ/FJ main unit.
13 Pull out material so that it is perpendicular to the paper tube. 1 T o prevent the pulled-out material from becoming crooked, secure with tape at the two edges and center , as shown in the figure.
14 8. Starting Operation Do not allow the hands or hair to touch the paper tube, flange, or sheet during take-up. The hands or hair may become caught. During operation, do not enter the sensor's detection area. Doing so will result in excessive take-up and cause printing to be interrupted.
15 T urn off the power . 1 Cut off the piece of material from the roll. 2 9. Removing Material Removal of taken-up roll material from the TU is a task which must be carried out by two or more persons. Injury may result if attempted by one person without assistance.
16 1 1. What to Do If... The CJ doesn't run * If a message like the one shown at right appears on the CJ Is the cutting function of the application software you're using not enabled? Do not use in such modes. Has the prefeed function on the CJ been set to [ENABLE]? Change the setting to [DISABLE].
17 Acceptable media widths Material weight for which take-up is possible Maximum material diameter after take-up Speed during material take-up Control switches Power consumption Acoustic noise level T.
18 MEMO.
R8-990901.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Roland TU-400 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Roland TU-400 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Roland TU-400, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Roland TU-400 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Roland TU-400, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Roland TU-400.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Roland TU-400. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Roland TU-400 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
