Manuel d'utilisation / d'entretien du produit SANTAFE-B1 du fabricant Quadra-Fire
Aller à la page of 48
R www .quadrare.com 7001-142D September 1, 2008 SANT A FE PELLET ST OVE Owner ’ s Manual Installation and Operation SANT AFE-B1 Model: HOT! DO NOT TOUCH . SEVERE BURNS MA Y RESUL T . CLOTHING IGNITION MA Y RESUL T . W ARNING • Keep children away .
Page 2 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R Hearth & Home T echnologies welcomes you to our tradi - tion of excellence! In choosing a Quadra-Fire appliance, you have our assurance of commitment to quality , durabil - ity , and performance.
R R R September 1, 2008 7001-142D Page Santa Fe Pellet Stove Section 1: Listing and Code Approvals A. Appliance Certications ...................... 4 B. Mobile Home Approved ...................... 4 C. Glass Specications ....................
Page 4 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R 1 Listing and Code Approvals A. Appliance Certication C. Glass Specications E. BTU & Efciency Specications This appliance is equipped with 5mm ceramic glass. Replace glass only with 5mm ceramic glass.
R R R September 1, 2008 7001-142D Page 5 Santa Fe Pellet Stove 2 Getting Started A . Design, Installation & Location Considerations 1. Appliance Location Consideration must be given to safety , convenience, trafc ow , and the fact that the appliance will need a chimney and chimney connector .
Page 6 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R D. Inspect Appliance & Components and Pre-Use Check List Reciprocating Saw Channel Locks Hammer Phillips Screwdriver T ape Meausre Pl.
R R R September 1, 2008 7001-142D Page 7 Santa Fe Pellet Stove 3 Dimensions and Clearances A. Appliance Dimensions Figure 7.2- Front View Figure 7.1 - T op View Figure 7.3 -Side View Figure 7.4 - Side View with T op V ent Adapter 25-7/16 in. (646 mm) 12-1 1/16 in .
Page 8 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R Straight Back Against W all Inches Millimeters A Back W all to Appliance 2 51 B Side W all to Appliance 6 152 Corner Installation Inches .
R R R September 1, 2008 7001-142D Page 9 Santa Fe Pellet Stove *L Exception for Horizontal Installations: USA INSTALLATIONS : If optional Cast Base is installed use a non-combustible oor protector extending under unit and to the sides, front and back of unit as shown in Floor Protection Diagram.
Page 10 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R Do not terminate vent in any enclosed or semi-enclosed area such as a carport, garage, attic, crawl space, under a sun deck or porch, narrow walkway or closely fenced area, or any location that can build up a concentration of fumes such as a stairwell, covered breezeway , etc.
R R R September 1, 2008 7001-142D Page 1 1 Santa Fe Pellet Stove Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage.
Page 12 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R 5 V enting Systems NOTE: • Illustrations reect typical installations and are FOR DESIGN PURPOSES ONL Y . • Illustrations/diagrams are not drawn to scale. • Actual installation may vary due to individual design preference.
R R R September 1, 2008 7001-142D Page 1 Santa Fe Pellet Stove B. Through The W all Horizontal termination cap must be a minimum of 12 inches. (05mm) from the wall.
Page 14 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R We recommend a minimum of 60 in. (1524mm) vertical, however above the eave is preferred.
R R R September 1, 2008 7001-142D Page 15 Santa Fe Pellet Stove Fire Risk Inspection of Chimney: • Masonry chimney must be in good condition. • Meets minimum standard of NFP A 21 1 • Factory-built chimney must be 6 inch (152mm) UL10 HT . W ARNING E.
Page 16 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R 6 Mobile Home 1. An outs ide air inlet mus t be pro vid ed for the comb ust ion air and must remain clear of leaves, debris, ice and/or snow . It must be unrestricted while the appliance is in use to prevent room air starvation which causes smoke spill age.
R R R September 1, 2008 7001-142D Page 17 Santa Fe Pellet Stove 7 Appliance Set-Up A. Outside Air Kit Instructions Flex Hose Hose Clamp Collar Assembly T rim Ring T erminatio n Cap Assembly Hose Clamp.
Page 18 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R 3 to 3 inch T op V ent Adapter 3 to 6 inch T op V ent Offset Adapter 1. Put a layer of high temperature silicone on the inch (76mm) exhaust outlet. Figure 18.1 2. Slide the top vent adapter onto the rear exhaust outl et and adjust the asse mbly to a verti cal positi on.
R R R September 1, 2008 7001-142D Page 19 Santa Fe Pellet Stove D. Optional Log Set Placement Instructions Figure 19.1 4 PIECE LOG SET INST ALLA TION OPTIONAL T OP LOG Figure 19.2 Figure 19.3 CAUTION Logs are FRAGILE. Use extreme care when handling or cleaning logs.
Page 20 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R E. Optional Gold or Nickel Grille & T rim Ring 1 . While holding door to face, remove 2 screws from grille and remove existing grille. Figure 20.1. 2. Install new grille using screws removed in step 1.
R R R September 1, 2008 7001-142D Page 21 Santa Fe Pellet Stove 1 . A 12 volt AC thermostat is required to operate this pellet appl iance. Y ou may use the inclu ded wall mount ther mo - stat or purchase an optional programmable thermostat or remote control.
Page 22 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R 8 Operating Instructions A. Fuel Size And Material 1. Wood Pellets Fuel pellets are made from sawdust or wood by-products. If the sour ce mat eri al is har dwo od, t hey c an hav e a high er min era l content, creating more ash.
R R R September 1, 2008 7001-142D Page 2 Santa Fe Pellet Stove Figure 23.1 E. Fire Characteristics A properly adjusted re with the heat output control switch set on “high” has a short active ame pattern that extends out of the repot approximately 4 inches (102mm).
Page 24 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R G. Iginition Cycles 1. During each ignition cycle, it is normal to see some smoke in the rebox. The smoke will stop once the re starts. 2. The convection blower will automatically turn on after your appli ance has been burning for approximately 10 minutes.
R R R September 1, 2008 7001-142D Page 25 Santa Fe Pellet Stove 9 T roubleshooting With proper installation, operation, and maintenance your appliance will provide years of trouble-free service.
Page 26 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R Symptom Possible Cause Corrective Action Slow or smoky start-up (Cont’d ) Dirty exhaust and/or venting system. Check for ash build up in unit, includ - ing behind rear panels, rebox, heat exchanger , exhaust blower and venting.
R R R September 1, 2008 7001-142D Page 27 Santa Fe Pellet Stove Symptoms Possible Cause Corrective Action Convection blower fails to start. #1 snap disc defective. Blower not plugged in. Blower is defective. Control box is defective. Replace snap disc.
Page 28 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R 10 Maintaining & Servicing Y our Appliance C. General Maintenance 1. T ypes of Fuel Depending on the type of fuel you are burning will dictate how often you have to clean your repot.
R R R September 1, 2008 7001-142D Page 29 Santa Fe Pellet Stove W ARNING • The cleaning slide plates must be fully CLOSED when appliance is operating. Hot pellets may fall into ashpan and start a re. Fire Hazard. 2. Cleaning Firepot with Cleaning Rod & Firepot Scraper • Frequency: Daily or more often as needed • By: Homeowner a.
Page 0 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R Figure 30.2 V acuum inside Exhaust V enting Cleaning Rods 10 Heat Exchanger T ubes The amount of ash buildup in the repot will be a good guide to determine how often you should clean the heat exchangers.
R R R September 1, 2008 7001-142D Page 1 Santa Fe Pellet Stove 1 1. Cleaning the Glass • Frequency: When clear view of the repot becomes obscure • By: Homeowner a. Appliance must be completely cool before cleaning glass. b. Use a damp paper towel or any non-abrasive glass cleaner .
Page 2 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R B. High Ash Fuel Content Maintenance • Frequency: As needed • By: Homeowner Correct Flame Size, Y ellow/White in Colo r Correct Figure 32.3 Ash Build Up in Firebox Pellets Back Up In Feed T ube Firepot Overfills T all, Lazy Flame, Orange in Colo r Incorrect Figure 32.
R R R September 1, 2008 7001-142D Page Santa Fe Pellet Stove 1. Convection Blower Replacement a. T urn down the thermostat, let appliance completely cool and then unplug appliance before servicing. b. The Convection Blower is located on the oor at the rear of the appliance.
Page 4 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R NOTE : Combustion Blower Gasket is also required. Sold separately under Part Number 240-0812. a. Turn down the thermostat, let appliance completely cool and then unplug appliance before servicing.
R R R September 1, 2008 7001-142D Page 5 Santa Fe Pellet Stove D. Igniter Replacement E. Bafe & Brick Removal 1. Shut do wn the app lia nce by tu rn ing do wn th e th ermo sta t and let the appliance completely cool down . After the appliance has cooled down, unplug it and remove the ash drawer .
Page 6 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R F . Bafe & Brick Replacement Right Brick Installed Brick is flush against back wall Brick in front of clip and Notches exposed Lift Brick, pull forward at an angle and drop down into not ches Opening at left side of Baffle T abs Do not remove rope from center brick Figure 36.
R R R September 1, 2008 7001-142D Page 7 Santa Fe Pellet Stove G. Glass Replacement • Glass is 5mm thick high temperature heat- resistant ceramic glass. • DO NOT REPLACE with any other material. • Alternate material may shatter and cause injury .
Page 8 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R 1 1 Reference Materials 7. Heat Exchangers The heat exchan gers transfer hot air from the exhau st syste m into convecton air . Remove the stainless steel top bafe to access the heat exchangers.
R R R September 1, 2008 7001-142D Page 9 Santa Fe Pellet Stove 16. Snap Disc #1 (Convection Blower) 1 10°F Snap disc #1 is located on the right side of the appliance on the bottom of the heat exchanger box. There are 2 purple wires connected to it.
Page 40 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R B. Component Locations Red Call Light Fuse Control Box V acuum Switch Junction Box High Med Low Heat Output Switch Reset Button Reset B .
R R R September 1, 2008 7001-142D Page 41 Santa Fe Pellet Stove Figure 41.1 - Door , Face, Glass & Door Latch Assembly 2 56 5 5 6 7 55 Figure 41.
Page 42 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R Figure 42.1 39 31 30 32 33 34 35 36 37 38 40 41 42 43 44 45 46 47 49 50 51 52 53 54 55 56 57 48 58 59 Item Nbr Description Item Nbr Desc.
R R R September 1, 2008 7001-142D Page 4 Santa Fe Pellet Stove D. Service Parts and Accessories Item # Service Parts Description Part Nbr Ash Catcher 7001-1 16 Ash Drawer Assembly 7001-004 5.
Page 44 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R Accessory Description Part Number Grille, Louver , Gold L VGRL-SF-GD Grille, Louver , Nickel L VGRL-SF-NL Log Set, 4 pieces 81 1-0852 Lo.
R R R September 1, 2008 7001-142D Page 45 Santa Fe Pellet Stove Date of Service Performed By Description of Service E. Service And Maintenance Log.
Page 46 7001-142D September 1, 2008 Santa Fe Pellet Stove R R R F . Warranty Policy Hearth & Home T echnologies LIMITED W ARRANTY Hearth & Home T echnologies (“HHT”) and its respective bra.
R R R September 1, 2008 7001-142D Page 47 Santa Fe Pellet Stove Noise resulting from minor expansion, contraction, or movement of certain parts is normal and complaints related to this noise are not covered by this warranty .
R Hearth & Home T echnologies 1445 North Highway Colville, W A 991 14 Division of HNI INDUSTRIES 7001-142D September 1, 2008 Page 48 CONT ACT INFORMA TION : Please contact your Quadra-Fire dealer with any questions or concerns. For the number of your nearest Quadra-Fire dealer logo onto www .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Quadra-Fire SANTAFE-B1 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Quadra-Fire SANTAFE-B1 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Quadra-Fire SANTAFE-B1, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Quadra-Fire SANTAFE-B1 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Quadra-Fire SANTAFE-B1, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Quadra-Fire SANTAFE-B1.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Quadra-Fire SANTAFE-B1. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Quadra-Fire SANTAFE-B1 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
