Manuel d'utilisation / d'entretien du produit EN250RYLB-O du fabricant Procom
Aller à la page of 21
1 COMP ACT VENT -FREE FIREPLACE SYSTEM OWNER ’ S OPERA TION AND INST ALLA TION MANUAL Do not store or use gasoline or other flam- mable vapors and liquids in the vicinity of this or any other appliance. WHA T TO DO IF YOU SMELL GAS Do not try to light any appliance.
2 T abel of Contents Safety Information W arnings...................................3 Air for Combustion and V entilation.........................5 Installation.............................................................7 Operating heater............
3 IMPORT ANT : Read this owner’s manual carefully and completely before trying to assemble, operate, or service this heater. Improper use of this heater can cause serious injury or death from burns, fire, explosion, electrical shock, and carbon monoxide poisoning.
4 SAFETY INFORMA TION Continued 15. Turn off and unplug heater and let cool before servicing. Only a qualified service person should service and repair heater. 16. Operating heater above elevations of 4,500 feet could cause pilot outage. 17. Do not operate heater if any log is broken.
5 AIR FOR COMBUSTION AND VENTILA TION W ARNING: This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate combustion and ventila- tion air. Read the following in- structions to insure proper fresh air for this and other fuel-burning appliances in your home.
6 W ARNING: Rework worksheet, adding the space of the adjoining unconfined space. The combined spaces must have enough fresh air to supply all appliances in both spaces. If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space.
7 NOTICE : This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your primary heat source. If you have a central heating system, you may run system's circulating blower while using heater.
8 CONNECTING T O GAS SUPPL Y W ARNING : A qualified service person must connect heater to gas supply. Follow all local codes. CAUTION: Never connect heater directly to the gas supply. This heater requires an external regulator (not supplied). lnstall the external regulator between the heater and gas supply.
9 W ARNING: T est all gas piping and connections for leaks after install- ing or servicing. Correct all leaks at once. W ARNING: Never use an open flame to check for a leak. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak.
10 W ARNING: Failure to position the parts in accordance with these diagrams may result in property damage or personal injury. CAUTION: After installation and periodically thereafter, check to en- sure that no flame comes in contact with any log. With the heater set to HIGH, check to see if flames contact any log.
11 b.manual select of main burner: Press BURNER button, the flame is on “MAN” select. At this selection, the main burner will keep working no matter what the temperature is set at. If there is a need to shut off the main burner, just press the “BURNER” button to make the burner on the “OFF” select.
12 3.After completion of the above-men- tioned two steps, the transmitter is kept in a state of readiness. If the appliance doesn’t working for a period time, just pull out the plug from the 1 10V electrical outlet. OPERA TIONS OF KEY -PRESS LOCKING 1.
13 Clean the pilot assembly also. A yellow tip on the pilot flame indicates dust and dirt in the pilot assembly. There is a small pilot air inlet hole about two inches from where the pilot flame comes out of the pilot assembly (see Figure 24). With the unit off, lightly blow air through the air inlet hole.
14 TROUBLESHOOTING ODS/pilot lights but flame is continuous igniting and the main burner couldn’t be lit. 1. Thermocouple connection loose at control board 2. Pilot flame not touching thermcouple which allows thermocouple to cool, causing pilot flame to go out.
15 SPECIFICA TIONS Btu 20,000/25,000 20,000/ 25,000 Gas T ype LP Gas Natural Gas Ignition Automatic Automatic Manifold Pressure 8"W.C. 3"W.C.
16 REPLACEMENT P ARTS Note : Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty. P ARTS UNDER W ARRANTY Contact authorized dealers of this product. If they can't supply original replacement part(s) call PRO-COM at (877) 886-5989 for referral information.
17 ILLUSTRA TED P ARTS BREAKDOWN EL250R YLB-O EN250RYLB-O.
18 P ARTS LIST This list contains replaceable parts used in your heater. When ordering parts, follow the instructions listed under Replacement Parts on page 16 of this manual.
19 ILLUSTRA TED P ARTS BREAKDOWN EL250R YLB-O EN250R YLB-O.
20 P ARTS LIST Y E K O N T R A P R E B M U N N O I T P I R C S E DY T Q 10 0 0 3 3 B Ey l b m e s s A s g o L g n i t a r o c e D1 2B 1 0 - 0 4 0 L E) B ( l e n a P p o T1 36 0 - 6 1 0 L El e n a P g .
21 Install the decorating logs. Fasten decorating logs 1 ¡¢ ¡¢ ¡¢ ¡¢ ¡¢ 2 ¡¢ ¡¢ ¡¢ ¡¢ ¡¢ 3 on to the co rresponde nt angle iron ( Figure 4 ). Insert the pinhole on the upper part of log 4 into the pin on the left side of log 1.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Procom EN250RYLB-O c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Procom EN250RYLB-O - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Procom EN250RYLB-O, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Procom EN250RYLB-O va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Procom EN250RYLB-O, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Procom EN250RYLB-O.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Procom EN250RYLB-O. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Procom EN250RYLB-O ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
