Manuel d'utilisation / d'entretien du produit PPCRT55 du fabricant Poulan
Aller à la page of 28
O WNER'S MANU AL MODEL: PPCR T55 REAR TINE TILLER AL W A YS WEAR EYE PRO TECTION DURING OPERA TION Visit our website: www .poulan-pr o.com W ARNING: Read this Man u al and f ollow all W ar nings and Saf ety Instr uctions . F ail ure to do so can re sult in serious in ju ry .
2 • Ne ver operate the tiller without proper guards , plates, or other saf ety protective de vices in place. • K eep children and pets awa y . • Do not ov er load the machine capacity b y attempting to till too deep at too f ast a rate. • Ne ver operate the machine at high speeds on slippery surf aces.
3 CONGRA TULA TIONS on your purchase of a new tiller . It has been designed, en gi neered and manu fac tured to giv e you the best pos sible de penda bil ity and per fo r m ance. Should you e xperience any prob lems you can not easily remedy , please contact your nearest authorized ser vice center .
4 T OOLS REQUIRED FOR ASSEMBL Y A sock et wrench set will make assemb ly easier . Standard wrench sizes are listed. (1) Utility knif e (1) Tire pressure gauge (1) P air of pliers (1) 9/16" wrench OPERA T OR’S POSITION (See Fig.
5 ASSEMBL Y • Grasp handle assembly . Hold in “up” position. Be sure handle lock remains in gearcase notch. Slide handle assembly into position. FIG. 4 UNP A CKING CART ON (See Fig. 2) CA UTION: Be careful of exposed sta ples when handling or disposing of cartoning material.
6 ASSEMBL Y INSERT CABLE CLIP (See Fig. 6) • Insert plastic cable clip into hole on the back of handle column. Push cab les into clip. A TT A CH THIS END T O SHIFT LEVER IN DI CA TO R SHIFT ROD FIG. 6 SHIFT ROD HAIRPIN CLIP SHIFT LEVER INDICA TOR FIG.
7 KNO W Y OUR TILLER READ THIS O WNER'S MANU AL AND SAFETY RULES BEFORE OPERA TING Y OUR TILLER. Compare the illustrations with y our tiller to familiarize y ourself with the location of various controls and adjustments. Sa ve this manual f or future reference .
8 TURNING • Release the drive control bar . • Mov e throttle control to “SLO W” position. • Place shift lev er indicator in “F” (f orward) position.
9 OPERA TION OIL LEVEL FIG. 12 BEFORE ST ART ING ENGINE IMPORT ANT : BE VERY CAREFUL NO T T O ALLOW DIR T T O ENTER THE ENGINE WHEN CHECKING OR ADDING OIL OR FUEL. USE CLEAN OIL AND FUEL AND ST ORE IN APPRO VED , CLEAN, CO VERED CONT AINERS. USE CLEAN FILL FUNNELS.
10 R U N C H O K E OPERA TION • Soil conditions are impor tant for proper tilling. Tines will not readily penetrate dry , hard soil which may con trib ute to e xcessive bounce and diffi cult handling of your tiller . Hard soil should be mois tened before tilling; how ev er , e xtremely wet soil will “ball-up” or clump during tilling.
11 MAINTENANCE GENERAL RECOMMEND A TIONS The warranty on this tiller does not co ver items that ha ve been subjected to operator ab use or negligence. T o receiv e full value from the w arranty , the operator must main tain tiller as instructed in this manual.
12 MAINTENANCE OIL FILLER PLUG OIL LEVEL OIL DRAIN PLUG FIG. 16 Disconnect spark plug wire before perf orming any maintenance (except car bu re tor adjustment) to prevent accidental start ing of engine . Prevent fi res! Keep the engine free of grass, leaves, spilled oil, or fuel.
13 MAINTENANCE e ngine_ar t _ 61 FIG. 19 AIR SCREEN BLO W ER HOUS ING MUFFLER Do not operate tiller without muffl er . Do not tamper with e xhaust system. Damaged muffl ers or spark arresters could create a fi re hazard. Inspect pe ri odi cally and re place if nec es sar y .
14 SER VICE AND ADJUSTMENTS CA UTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug. TILLER T O ADJUST HANDLE HEIGHT (See Fig. 20) Select handle height best suited f or your tilling conditions. Handle height will be diff erent when tiller digs into soil.
15 SER VICE AND ADJUSTMENTS CABLE CLIP SCREW DRIVE CONTROL CABLE EXTENSION SPRING ENGINE PULLEY IDLER PULLEY TRANS MIS SION PULLEY LESS TEN SION 5/8" MORE TEN SION FIG. 23 T O REPLA CE GROUND DRIVE BEL T (See Figs. 22 and 23) • Remove belt guard as described in “T O REMO VE BEL T GU ARD”.
16 SER VICE AND ADJUSTMENTS tine_13 FIG. 26 TINE REPLA CEMENT (See Figs. 24, 25, and 26) CA UTION: Tines are sharp. Wear gloves or other pr otection when han- dling tines.
17 SER VICE AND ADJUSTMENTS FIG. 27 engine_art_78 THRO TTLE CONTROL CLAMP SCREW CASING AND WIRE ENGINE T O ADJUST THRO TTLE CONTROL CABLE (See Fig. 27) The throttle control has been preset at the f actor y and ad just ment should not be necessar y .
18 ST ORA GE ENGINE OIL Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this man ual). CYLINDER(S) • Remov e spark plug. • P our 1 ounce (29 ml) of oil through spark plug hole into cylinder .
19 Will not start 1. Out of fuel. 1. Fill fuel tank . 2. Engine not “CHOKED” proper ly . 2. See “T O ST AR T ENGINE” in Operation section. 3. Engine fl ooded. 3. Wait se ver al minutes before attempting to start. 4. Dir ty air cleaner . 4. Clean or replace air cleaner car tridge.
20 REP AIR P AR TS TILLER - - MODEL NUMBER PPCR T55 (96091001200), PRODUCT NUMBER 960 91 00-12 HANDLE ASSEMBL Y KEY P ART NO . NO. DESCRIPTION 17 532 10 92-29 Loc k, Handle 18 873 68 06-00 Nut, Cro wnlock 3/8-16 unc 19 819 13 16-11 W asher 13/32 x 1 x 11 Ga.
21 KEY P ART NO . NO. DESCRIPTION 2 810 04 06-00 W asher , Loc k 3/8 3 873 22 06-00 Nut, He x 3/8-16 4 532 17 01-27 Shield, Inner Belt Guard R T 5 532 16 43-29 Pin Spirol Flared 6 532 11 01-11 Le ver , Shift 7 872 11 04-04 Bolt, Carriage 1/4-20 x 1/2 Gr .
22 KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION REP AIR P AR TS TILLER - - MODEL NUMBER PPCR T55 (96091001200), PRODUCT NUMBER 960 91 00-12 MAINFRAME, RIGHT SIDE 2 873 97 05-00 Loc knut, He x, Flange 5/16-18 5 532 10 23-32 Br acket, Reinf orcement 7 532 10 21-73 Counter W eight, R.
23 12 13 15 16 14 9 9 8 5 18 23 22 21 19 18 3 2 29 31 7 6 5 4 11 10 30 28 18 32 33 34 18 48 60 24 44 18 42 43 41 49 40 39 37 38 37 50 36 20 25 27 35 25 24 44 51 58 53 52 53 transmission_19.5b KEY P ART NO . NO. DESCRIPTION NO TE: All component dimensions given in U .
24 1 2 29 29 15 1 11 11 12 12 13 14 14 24 23 26 27 22 21 20 19 11 12 16 25 33 32 16 3 4 7 8 9 5 5 23 23 28 24 18 6 5 5 30 tine_shield_16_in 12 12 11 11 10 21 532 10 21-56 Stak e, Depth 22 874 93 06-32 Bolt, He x 3/8-16 x 2 23 532 00 44-40 Hinge 24 872 14 04-04 Bolt, Carriage 1/4-20 x 1/2 Gr .
25 2 11 11 10 9 9 4 4 5 34 3 3 1 2 1 1 1 9 9 8 tine_ipb_1 KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION 1 532 00 44-59 Tine , Outer , L.H. 2 532 13 26-73 Cle vis Pin 3 532 00 65-54 Tine , Inner , L.H. 4 532 12 46-60 Retainer , Spr ing Zinc 5 532 13 27-27 Assemb ly , Hub and Plate, L.
26 1 532 40 37-07 Decal, Belt Guard 2 532 15 78-01 Decal, Control P anel 3 532 40 36-53 Decal, Logo 4 532 13 75-38 Decal, Control Tine 5 532 12 04-31 Decal, Hand Placement 6 532 10 21-80 Decal, Shift .
27 LIMITED W ARRANTY The Manuf acturer warrants to the original consumer purchaser that this product as manuf actured is free from de- f ects in mater ials and work man ship .
This product has been e xper tly en gi neered and carefully manu fac tured to rigid quality stan dards. As with all mechanical products, some adjustments or par t replacement ma y be necessar y during the lif e of your unit.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Poulan PPCRT55 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Poulan PPCRT55 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Poulan PPCRT55, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Poulan PPCRT55 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Poulan PPCRT55, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Poulan PPCRT55.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Poulan PPCRT55. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Poulan PPCRT55 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
