Manuel d'utilisation / d'entretien du produit PD2042STA du fabricant Poulan
Aller à la page of 48
OWNER'S MANUAL MODEL: PD2042ST A LA WN TRACTOR AL W A YS WEAR EYE PROTECTION DURING OPERA TION W ARNING: Read this Owner's Man u al and follow all W arn- ings and Safety Instructions. Fail ure to do so can re sult in serious in ju ry . IMPOR T ANT MANUAL Do Not Throw A way 185491 Re v .
2 DO NO T : • Do not turn on slopes unless necessar y , and then, turn slowly and gradually do wnhill, if possible . • Do not mow near drop-offs , ditches, or embankments . The mower could suddenly turn ov er if a wheel is o ver the edge of a cliff or ditch, or if an edge cav es in.
3 W ARNING: In order to pre vent ac- ci den tal star ting when setting up, trans por t ing, ad just ing or making re- pairs, al ways dis con nect spark plug wire and place wire where it can not contact spark plug. W ARNING: Do not coast down a hill in neutral, y ou may lose contr ol of the tractor .
4 GASOLINE CAP A CITY 2.0 GALLONS AND TYPE: UNLEADED REGULAR OIL TYPE (API-SF-SJ): SAE 30 (abov e 32°F) SAE 5W -30 (below 32°F) OIL CAP A CITY : W/FIL TER 4.0 PINTS W/O FIL TER 3.75 PINTS SP ARK PLUG: CHAM PI ON QC12YC (GAP: .040") GROUND SPEED (MPH): Forw ard: 1st 1.
5 UNASSEMBLED P AR TS (1) Large Flat Washer Steering Wheel Insert Steering Sleeve Steering Wheel (1) Knob (1) Washer 17/32 x 1-3/16 x 12 Gauge Seat (2) Mulch Blades (2) Keys Slope Sheet Steering Extension Shaft Steering Adapter (1) Oil Drain Tube (1) Hex Bolt 1/4-28 x 1-1/4 (1) Locknut 1/4-28 (1) Locknut 1/2-20 (4) Washers 3/8 x 3/4 x 14 Ga.
6 HO W T O SET UP Y OUR TRA CT OR INST ALL SEA T (See Fig. 2) Adjust seat bef ore tightening adjustment knob . • Remov e adjustment knob and fl at washer securing seat to cardboard packing and set aside f or assembly of seat to tractor . • Pivot seat upward and remov e from the cardboard pack- ing.
7 ASSEMBL Y FIG. 2 SEA T P AN SHOULDER BOL T ADJUSTMENT KNOB FLA T W ASHER SEA T FIG. 3 SEA T P AN LABEL CHECK B A TTER Y (See Fig. 3) • Lift seat pan to raised position. • If this batter y is put into ser vice after month and year indicated on label (label located between terminals) charge batter y f or minimum of one hour at 6-10 amps.
8 ASSEMBL Y FIG. 4B T O CONVERT T O B A GGING OR DISCHARGING NO TE: The mulcher blades will dis charge and bag grass , but f or best bagging and discharging install the high per- fo r mance blades. • Remov e mulcher plate and mulcher blades and install high perf ormance blades, (see BLADE REMO V AL in the MAINTENANCE sec tion of this man u al).
9 OPERA TION These symbols ma y appear on your tr actor or in literature supplied with the product. Learn and understand their mean- ing. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models .
10 OPERA TION KNO W Y OUR TRA CT OR READ THIS O WNER'S MANU AL AND SAFETY R ULES BEFORE OPERA TING Y OUR TRA CT OR Compare the illustrations with y our tractor to f amiliarize y ourself with the locations of v arious controls and ad just ments. Sav e this manual for future ref erence.
11 OPERA TION The operation of any tractor can result in f oreign objects thro wn into the ey es, which can result in severe e ye dam age. Al wa ys wear safety glass es or eye shields while operating your tractor or per for m ing any adjustments or repair s.
12 OPERA TION T O OPERA TE MO WER (See Fig. 8) Y our tractor is equipped with an operator presence sensing s witch. Any attempt b y the operator to lea ve the seat with the engine running and the attachment clutch engaged will shut off the engine. • Select desired height of cut.
13 OPERA TION BEFORE ST ARTING THE ENGINE CHECK ENGINE OIL LEVEL • The engine in your tractor has been shipped, from the f actor y , already fi lled with sum mer weight oil.
14 MULCHING MO WING TIPS IMPORT ANT : FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUIL T -UP GRASS AND TRASH. CLEAN AFTER EA CH USE. • The spe cial mulch ing blade will recut the g rass clip- pings many times and reduce them in size so that as they f all onto the lawn they will disperse into the g rass and not be noticed.
15 MAINTENANCE B E F O R E E A C H U S E T R A C T 0 R Inspect Muffler/Spark Arrester Lubrication Chart Check Brake Operation Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Pa.
16 MAINTENANCE BLADE REMO V AL (See Fig. 11) • Raise mower to highest position to allow access to blades . • Remov e blade bolt, lock washer and fl at washer se cur ing blade . • Install new or resharpened blade with trailing edge up tow ards deck as sho wn.
17 MAINTENANCE V- B E LT S Check V -belts for deterioration and wear after 100 hours of operation and replace if necessary . The belts are not ad just able. Re place belts if they begin to slip from wear . FIG. 13 ENGINE LUBRICA TION Only use high quality detergent oil rated with API service classifi cation SF-SJ .
18 MAINTENANCE MUFFLER Inspect and replace corroded muffl er and spar k arrester (if equipped) as it could create a fi re hazard and/or dam- age. SP ARK PLUGS Replace spark plugs at the beginning of each mowing season or after e very 100 hours of operation, whiche v er occurs fi rst.
19 SER VICE AND ADJUSTMENTS W ARNING: T O A V OID SE RI OUS IN JU R Y , BEFORE PERFORMING ANY SER VICE OR ADJUST - MENTS: • Depress clutc h/brake pedal fully and set parking brake. • Place gearshift lever in neutral (N) position. • Place attachment c lutch in “DISENGA GED” position.
20 SER VICE AND ADJUSTMENTS NUT "E" "D" "D" MANDREL FIG. 20 NUT "F" FRONT LINKS FIG. 21 FRONT -T O-BA CK ADJUSTMENT (See Figs.
21 SER VICE AND ADJUSTMENTS FIG. 22 T O REPLA CE MO WER BLADE DRIVE BEL T (See Fig. 22) The mower b lade dr ive belt ma y be replaced without tools. P ark the tractor on le v el surf ace. Engage par king brake . BEL T REMO V AL - • Remove mow er from tractor (See “T O REMO VE MO W ER” in this section of man ual).
22 SER VICE AND ADJUSTMENTS T O REMO VE WHEEL FOR REP AIRS (See Fig. 26) • Block up axle securely . • Remov e axle co ver , retaining ring and washers to allow wheel remov al (rear wheel contains a square k ey - Do not lose). • Repair tire and reassemble .
23 REPLA CING BA TTER Y (See Figs. 28 and 29) W ARNING: Do not short batter y ter- mi nals by allowing a wrenc h or any other object to contact both terminals at the same time. Bef ore connect- ing battery , remove metal bracelets, wristwatch bands, rings, etc.
24 ENGINE T O AD JUST THR O TTLE CON TROL CABLE (See Fig. 31) The throttle control has been preset at the f actor y and ad just ment should not be necessar y . Check adjustment as described below bef ore loosening cable . If adjustment is necessar y , proceed as f ollows: • With engine not running, mov e throttle control le ver to f ast position.
25 ST ORA GE Immediately prepare your tr actor f or storage at the end of the season or if the tractor will not be used f or 30 da ys or more. W ARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reac h an open fl ame or spark.
26 PROBLEM CA USE CORRECTION TR OUBLESHOO TING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” proper ly . 2. See “T O ST ART ENGINE” in Operation section. 3. Engine fl ooded. 3. Wait se ver al minutes bef ore attempting to star t.
27 PROBLEM CA USE CORRECTION TR OUBLESHOO TING POINTS Engine continues to run 1. F aulty operator-safety presence control system. 1. Check wiring, switches and connections. If not when operator leaves seat corrected, contact an author ized service center/ with attachment clutc h depar tment.
28 NO TES.
29 TRA CT OR - - MODEL NUMBER PD2042ST A, PRODUCT NUMBER 954 56 97-07 SCHEMA TIC BATTERY FUSE IGNITION SWITCH RED RED RED BLACK IGNITION UNIT HEADLIGHTS REMOVABLE CONNECTIONS BLACK BLACK BLACK WHITE W.
30 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD2042ST A, PRODUCT NUMBER 954 56 97-07 ELECTRICAL 28 29 26 24 42 43 27 27 25 41 27 27 40 33 90 30 8 2 1 27 D .
31 KEY P ART NO . NO . DESCRIPTION 1 144927 Batter y 12 V olt 35 Amp 2 74760412 Bolt He x Hd 1/4-20unc X 3/4 8 176689 Batter y Bo x 16 176138 Switch Interlock Push-In 21 183759 Harness Socket Light 22.
32 26 25 64 208 13 208 11 1 3 2 9 208 209 209 209 5 5 207 3 3 3 142 145 37 3 37 24 26 25 31 24 30 35 3 26 33 10 26 34 35 205 38 205 206 159 3 115 3 142 211 114 58 18 17 28 264 263 259 258 261 166 39 c.
33 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD2042ST A, PRODUCT NUMBER 954 56 97-07 CHASSIS AND ENCLOSURES KEY P ART NO . NO . DESCRIPTION 1 174619 Chassis 2 176554 Dra wbar 3 17060612 Screw 3/8-16x.
34 29 28 112 14 41 38 39 57 51 74 75 78 76 77 1 25 19 24 2 53 35 34 37 36 35 62 36 59 212 55 77 61 22 27 26 6 113 18 51 5 18 6 85 52 30 32 32 30 52 11 85 80 4 3 13 81 84 82 64 65 145 79 16 96 26 27 51.
35 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD2042ST A, PRODUCT NUMBER 954 56 97-07 DRIVE KEY P ART NO . NO . DESCRIPTION KEY P AR T NO . NO . DESCRIPTION 1 - - - - - - T ransaxle P eerless (206-545C.
36 5 5 4 3 43 6 43 8 10 40 32 11 8 6 87 46 46 8 6 87 29 88 71 17 43 91 2 1 41 42 37 36 37 38 12 39 44 51 54 33 35 34 68 67 67 67 13 65 68 15 15 15 29 29 82 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD.
37 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD2042ST A, PRODUCT NUMBER 954 56 97-07 STEERING ASSEMBL Y KEY P ART NO . NO . DESCRIPTION 1 180656 Wheel Steering 2 172393 Axle Asm Cast Iron L T 3 169840.
38 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD2042ST A, PRODUCT NUMBER 954 56 97-07 SEA T ASSEMBL Y 1 171683 Seat 2 140551 Brac ket Piv ot Seat 8 720 3 71110616 Bolt Fin He x 3/8-16 Unc X 1 4 19131610 W asher 13/32 X 1 X 10 Ga 5 145006 Clip Push-In 6 73800600 Nut He x w/Ins.
39 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD2042ST A, PRODUCT NUMBER 954 56 97-07 DECALS NO TE: All component dimensions giv en in U .S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 6 2 1 5,8 4,10 3,9 11 7 WHEELS AND TIRES KEY P ART NO .
40 14 38 2 1 OPTIONAL EQUIPMENT Spark Arrester 29 10 6 5 72 13 26 25 4 8 17 16 17 3 81 23 45 44 46 32 31 33 37 33 41 112 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD2042ST A, PRODUCT NUMBER 954 56 97-.
41 36 15 20 16 17 18 20 20 15 20 4 5 6 2 3 1 6 5 4 7 23 24 25 27 28 29 30 37 41 40 38 12 11 31 32 31 32 19 19 13 13 13 13 49 26 50 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD2042ST A, PRODUCT NUMBER .
42 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD2042ST A, PRODUCT NUMBER 954 56 97-07 MO WER DECK 15 14 13 11 10 9 8 16 68 30 31 32 33 146 148 145 150 45 144 147 147 142 149 142 54 52 53 55 56 34 1 46 44 21 24 25 26 27 2 28 29 23 21 21 21 18 18 20 2 48 59 19 4 3 5 6 21 40 143 36 40 37 40 159 140 37 184 42_deck_man-t-path_4.
43 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 182032X421 Mo wer Dec k Assembly , 42" 2 72140506 Bolt 3 138017 Brac ket Asm F r .
44 NO TES.
45 LIMITED W ARRANTY The Manuf acturer warr ants to the original consumer purchaser that this product as manufactured is free from def ects in mater i- als and work man ship .
46 T E C U M S E H ® Issued Jan uar y 1980 Re vised January 1991 T E C U M S E H ® SER VICE POLICY W ARRANTY LIMITED W ARRANTIES FOR NEW PEERLESS GEAR PO WER TRAIN COMPONENTS A.
47 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
Y our POULAN PRO product has been expertly en gi neered and carefully manu fac tured to rigid quality stan dards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit. FOR SER VICE OR REPLACEMENT P ARTS: 1.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Poulan PD2042STA c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Poulan PD2042STA - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Poulan PD2042STA, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Poulan PD2042STA va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Poulan PD2042STA, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Poulan PD2042STA.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Poulan PD2042STA. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Poulan PD2042STA ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
