Manuel d'utilisation / d'entretien du produit PD18H42STA du fabricant Poulan
Aller à la page of 48
OWNER'S MANUAL MODEL: PD18H42ST A LA WN TRACTOR AL W A YS WEAR EYE PROTECTION DURING OPERA TION W ARNING: Read this Owner's Man u al and follow all W arn- ings and Safety Instructions. Fail ure to do so can re sult in serious in ju ry . IMPOR T ANT MANUAL Do Not Throw A way 184581 Re v .
2 DO NO T : • Do not turn on slopes unless necessar y , and then, turn slowly and gradually do wnhill, if possible . • Do not mow near drop-offs , ditches, or embankments . The mower could suddenly turn ov er if a wheel is o ver the edge of a cliff or ditch, or if an edge cav es in.
3 W ARNING: In order to pre vent ac- ci den tal starting when setting up, trans por t ing, ad just ing or making re- pairs, al ways dis con nect spark plug wire and place wire where it can not contact spark plug. W ARNING: Do not coast down a hill in neutral, y ou may lose contr ol of the tractor .
4 GASOLINE CAP A CITY 2.0 GALLONS AND TYPE: UNLEADED REGULAR OIL TYPE (API-SF-SJ): SAE 10W30 (abov e 32°F) SAE 5W -30 (below 32°F) OIL CAP A CITY : 4.0 PINTS SP ARK PLUG: CHAM PI ON RC12YC (GAP: .040") GROUND SPEED (MPH): Forw ard: 0-5.5 Rev erse 0-2.
5 UNASSEMBLED P AR TS (1) Large Flat Washer Steering Wheel Insert Steering Sleeve Steering Wheel (1) Knob (1) Washer 17/32 x 1-3/16 x 12 Gauge Seat (2) Mulch Blades (2) Keys Slope Sheet Steering Extension Shaft Steering Adapter (1) Oil Drain Tube (1) Hex Bolt 1/4-28 x 1-1/4 (1) Locknut 1/4-28 (1) Locknut 1/2-20 (4) Washers 3/8 x 3/4 x 14 Ga.
6 HO W T O SET UP Y OUR TRA CT OR INST ALL SEA T (See Fig. 2) Adjust seat bef ore tightening adjustment knob . • Remov e adjustment knob and fl at washer securing seat to cardboard packing and set aside f or assembly of seat to tractor . • Pivot seat upward and remov e from the cardboard pack- ing.
7 ASSEMBL Y FIG. 2 SEA T P AN SHOULDER BOL T ADJUSTMENT KNOB FLA T W ASHER SEA T FIG. 3 SEA T P AN LABEL CHECK B A TTER Y (See Fig. 3) • Lift seat pan to raised position. • If this batter y is put into ser vice after month and year indicated on label (label located between terminals) charge batter y f or minimum of one hour at 6-10 amps.
8 ASSEMBL Y ✓ CHE CKLIST BEFORE Y OU OPERA TE AND ENJO Y Y OUR NEW TRAC- TOR, WE WISH T O ASSURE THA T Y OU RECEIVE THE BEST PERFORMANCE AND SA TISF A CTION FR OM THIS QU ALITY PRODUCT . PLEASE REVIEW THE FOLLOWING CHECKLIST : ✓ All assembly instructions hav e been completed.
9 OPERA TION These symbols ma y appear on your tr actor or in literature supplied with the product. Learn and understand their mean- ing. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models .
10 OPERA TION KNO W Y OUR TRA CT OR READ THIS O WNER'S MANU AL AND SAFETY R ULES BEFORE OPERA TING Y OUR TRA CT OR Compare the illustrations with y our tractor to f amiliarize y ourself with the locations of v arious controls and ad just ments. Sav e this manual for future ref erence.
11 OPERA TION The operation of any tractor can result in f oreign objects thro wn into the ey es, which can result in severe e ye dam age. Al wa ys wear safety glass es or eye shields while operating your tractor or per for m ing any adjustments or repairs.
12 OPERA TION T O OPERA TE ON HILLS W ARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across an y slope. • Choose the slowest speed bef ore star ting up or down hills. • A v oid stopping or changing speed on hills.
13 OPERA TION T O ST ART ENGINE (See Fig. 5) When star ting the engine for the fi rst time or if the engine has run out of fuel, it will take e xtra cranking time to mo v e fuel from the tank to the engine. • Be sure freewheel control is in the transmission en gaged position.
14 FIG. 10 MO WING TIPS • Mower should be properly lev eled for best mowing per- f ormance. See “T O LEVEL MOWER HOUSING” in the Ser vice and Adjustments section of this manual. • The left hand side of mow er should be used f or trim- ming. • Drive so that clippings are discharged onto the area that has been cut.
15 MULCHING MO WING TIPS IMPORT ANT : FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUIL T -UP GRASS AND TRASH. CLEAN AFTER EA CH USE. • The spe cial mulch ing blade will recut the g rass clip- pings many times and reduce them in size so that as they f all onto the lawn they will disperse into the g rass and not be noticed.
16 MAINTENANCE B E F O R E E A C H U S E T R A C T 0 R Inspect Muffler/Spark Arrester Lubrication Chart Check Brake Operation Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Pa.
17 MAINTENANCE BLADE REMO V AL (See Fig. 12) • Raise mower to highest position to allow access to bla d e s. • Remov e blade bolt, lock washer and fl at was he r se cur ing bla d e. • Install new or reshar pened blade with tr ailing edge up tow ards deck as sho wn.
18 CLEAN AIR INT AKE/COOLING AREAS T o insure proper cooling, make sure the gr ass screen, cooling fi ns, and other external surf aces of the engine are kept clean at all times . Ev er y 100 hours of operation (more often under e xtremely dusty , dir ty conditions), remov e the blo wer housing and other cooling shrouds.
19 MAINTENANCE MUFFLER Inspect and replace corroded muffl er and spar k arrester (if equipped) as it could create a fi re hazard and/or dam- age. SP ARK PLUGS Replace spark plugs at the beginning of each mowing season or after e very 100 hours of operation, whiche v er occurs fi rst.
20 SER VICE AND ADJUSTMENTS W ARNING: T O A V OID SERIOUS INJUR Y , BEFORE PERFORMING ANY SER VICE OR AD JUST - MENTS • Depress clutc h/brake pedal fully and set parking brake. • Place motion control le ver in neutral (N) position. • Place attachment c lutch in “DISENGA GED” position.
21 SER VICE AND ADJUSTMENTS NUT "E" "D" "D" MANDREL FIG. 21 NUT "F" FRONT LINKS FIG. 22 FRONT -T O-BA CK ADJUSTMENT (See Figs.
22 SER VICE AND ADJUSTMENTS FIG. 23 T O REPLA CE MO WER BLADE DRIVE BEL T (See Fig. 23) The mower b lade dr ive belt ma y be replaced without tools. P ark the tractor on le v el surf ace. Engage par king brake . BEL T REMO V AL - • Remove mow er from tractor (See “T O REMO VE MO W ER” in this section of man ual).
23 SER VICE AND ADJUSTMENTS T O REMO VE WHEEL FOR REP AIRS (See Fig. 27) • Block up axle securely . • Remov e axle co ver , retaining ring and washers to allow wheel remov al (rear wheel contains a square k ey - Do not lose). • Repair tire and reassemble .
24 T O REMO VE HOOD AND GRILL ASSEMBL Y (See Fig. 31) • Raise hood. • Unsnap headlight wire connector . • Stand in front of tractor . Grasp hood at sides , tilt tow ard engine and lift off of tractor . • T o replace, re v erse abov e procedure.
25 SER VICE AND ADJUSTMENTS CABLE CLAMP SCREW SPEED CONTROL BRA CKET IDLE FUEL ADJUSTING NEEDLE IDLE SPEED ADJUSTING SCREW THRO TTLE LEVER FIG. 32 FIG.
26 ST ORA GE Immediately prepare your tr actor f or storage at the end of the season or if the tractor will not be used f or 30 da ys or more. W ARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reac h an open fl ame or spark.
27 PROBLEM CA USE CORRECTION TR OUBLESHOO TING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “T O ST ART ENGINE” in Operation section. 3. Engine fl ooded. 3. Wait se veral minutes bef ore attempting to start.
28 PROBLEM CA USE CORRECTION TR OUBLESHOO TING POINTS Engine continues to run 1. F aulty operator-saf ety presence control system. 1. Check wiring, switches and connections. If not when operator leaves seat corrected, contact an authorized ser vice center/ with attachment clutc h depar tment.
29 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD18H42ST A, PRODUCT NO . 954 56 94-93 SCHEMA TIC 87 87A 85 86 30 RELAY WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE REPLACED TO PROPERLY SECURE YOUR WIRING.
30 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD18H42ST A, PRODUCT NO . 954 56 94-93 ELECTRICAL 28 29 26 24 42 43 27 27 25 41 27 27 40 33 30 90 8 2 1 27 16 16 52 D .
31 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD18H42ST A, PRODUCT NO . 954 56 94-93 ELECTRICAL 1 163465 Batter y 12 V olt 25 Amp 2 74760412 Bolt Hex Hd 1/4-20unc X 3/4 8 176689 Box Battery 16 176137 S.
32 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD18H42ST A, PRODUCT NO . 954 56 94-93 CHASSIS AND ENCLOSURES 26 25 58 64 208 13 208 11 1 3 2 9 208 209 209 5 5 207 3 3 3 142 3 3 3 142 145 37 3 37 24 26 2.
33 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD18H42ST A, PRODUCT NO . 954 56 94-93 CHASSIS AND ENCLOSURES 1 174619 Chassis 2 176554 Drawbar 3 17060612 Screw 3/8-16 x 3/4 5 155272 Bumper Hood/Dash 9 168337X012 Dash 10 72140608 Bolt RdHd Sqnk. 3/8-16 Unc x 1 11 174996 P anel Asm.
34 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD18H42ST A, PRODUCT NO . 954 56 94-93 DRIVE 66 29 28 32 30 52 32 59 38 61 41 53 35 55 36 62 35 36 22 39 34 16 1 77 77 30 52 56 64 65 212 63 116 70 57 96 2.
35 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD18H42ST A, PRODUCT NO . 954 56 94-93 DRIVE KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 - - - - - - T ransaxle Hydro Gear Model 314-.
36 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD18H42ST A, PRODUCT NO . 954 56 94-93 STEERING ASSEMBL Y 5 5 4 3 43 6 43 8 10 40 32 11 8 6 87 46 46 8 6 87 29 88 71 17 43 91 2 1 41 42 37 36 37 38 12 39 4.
37 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD18H42ST A, PRODUCT NO . 954 56 94-93 STEERING ASSEMBL Y 1 180656 Wheel Steer ing 2 184706 Axle Asm F ront 3 169840 Spin dle Asm Lh 4 169839 Spin dle Asm .
38 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD18H42ST A, PRODUCT NO . 954 56 94-93 ENGINE 2 1 OPTIONAL EQUIPMENT Spark Arrester 29 105 105 3 16 101 77 4 80 101 13 23 45 14 38 44 46 32 31 33 37 33.
39 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD18H42ST A, PRODUCT NO . 954 56 94-93 ENGINE NO TE: All component dimensions giv en in U .S. inches 1 inch = 25.
40 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD18H42ST A, PRODUCT NO . 954 56 94-93 SEA T ASSEMBL Y KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO .
41 WHEELS & TIRES KEY P ART NO . NO . DESCRIPTION 1 59192 Cap V alve Tire 2 65139 Stem V alve 3 170455 Tire F Ts 15 X 6 0 - 6 Service 4 59904 T ube Front (Service Item Only) 5 106732X421 Rim Asm 6.
42 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD18H42ST A, PRODUCT NO . 954 56 94-93 MO WER LIFT 36 15 20 16 17 18 20 20 15 20 4 5 6 2 3 1 6 5 4 7 37 41 40 38 12 11 31 32 31 32 19 19 13 13 13 13 23 24 .
43 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD18H42ST A, PRODUCT NO . 954 56 94-93 MO WER LIFT 1 184432 Plunger Asm. 2 159476 Shaft Asm Lift 3 178981 Pin Groov e 4 12000002 E Ring #5133-62 5 19211621 W asher 21/32 x 1 x 21 Ga.
44 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD18H42ST A, PRODUCT NO . 954 56 94-93 MO WER DECK 15 14 13 11 10 9 8 16 68 30 31 32 33 146 148 145 150 45 144 147 147 142 149 142 54 52 53 55 56 34 1 46 44 21 24 25 26 27 2 28 29 23 21 21 21 18 18 20 2 48 59 19 4 3 5 6 21 40 143 36 40 37 40 159 140 37 184 42_deck_man-t-path_4.
45 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PD18H42ST A, PRODUCT NO . 954 56 94-93 MO WER DECK 1 182032X421 Mower Dec k Assemb ly , 42" 2 72140506 Bolt 3 138017 Brack et Asm F r .
46 LIMITED W ARRANTY The Manuf acturer warr ants to the original consumer purchaser that this product as manufactured is free from def ects in mater i- als and work man ship .
47 15 DEGREES MAX. FO LD ALO NG DOTTED LINE THIS IS A 15 DEGREE SLO PE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
Y our POULAN PRO product has been expertly en gi neered and carefully manu fac tured to rigid quality stan dards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit. FOR SER VICE OR REPLACEMENT P AR TS: 1.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Poulan PD18H42STA c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Poulan PD18H42STA - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Poulan PD18H42STA, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Poulan PD18H42STA va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Poulan PD18H42STA, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Poulan PD18H42STA.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Poulan PD18H42STA. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Poulan PD18H42STA ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
