Manuel d'utilisation / d'entretien du produit MODEL 7310 du fabricant Porter-Cable
Aller à la page of 25
Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No.
T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury.
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm.
Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
6 ADDITIONAL SPECIFIC SAFETY RULES 1. HOLD POWER TOOLS BY INSULATED GRIPPING SURFACES WHEN PERFORMING AN OPERATION WHERE THE CUTTING TOOL MAY CONTACT HIDDEN WIRING OR ITS OWN CORD. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
7 NOTES.
8 SAVE THESE INSTRUCTIONS! SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F .
9 If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage.
10 FUNCTIONAL DESCRIPTION FOREWORD Porter-Cable Laminate Trimmers are designed for flush and bevel trimming laminated plastics, phenolics, and other similar materials having a bonding agent too hard to be trimmed with ordinary tools.
11 TO AVOID PERSONAL INJURY OR DAMAGE TO FINISHED WORK ALWAYS ALLOW THE MOTOR TO COME TO A COMPLETE STOP BEFORE SETTING TRIMMER DOWN. TO INST ALL BIT DISCONNECT TOOL FROM POWER SOURCE. 1. On Models 7310 and 7319 bits may be installed with the motor unit either assembled or removed from the base.
ADJUSTING DEPTH OF CUT DISCONNECT TOOL FROM POWER SOURCE. 1. Loosen base locking screw (Fig. 3) approximately one-quarter turn. 2. Turn depth adjusting wheel (Fig. 3) clockwise, looking at top of wheel, to raise cutter reducing depth of cut or counterclockwise to lower cutter for increasing depth of cut.
13 ASSEMBLING AND ADJUSTING BASE AND ROLLER GUIDE 1. Remove power unit from base unit (see “TO INSTALL BIT”), and install the bit. 2. The base and roller guide (A) Fig. 4, is assembled at the factory. To assemble, remove a sub-base mounting screw (A) Fig.
14 5. Remove guide setting gauge from trimmer and install flush trimming bit. 6. Adjust depth of cut so that the straight portion of the bit extends below the trimmer base at least the thickness of the material to be trimmed. 7. Make a trial cut on scrap material.
15 be sure at least 1 / 2 " of bit shank is engaged in collet. Do not use bits that result in having less than 1 / 2 " of bit shank engaged in collet. To do so may cause poor gripping of collet resulting in loose bit and damage to work, or personal injury should the bit come out of collet.
16 TO INST ALL & REMOVE BIT DISCONNECT TOOL FROM POWER SOURCE. 1 . Insert long portion of hex wrench (furnished) through spindle lock hole (see Fig. 10) so that wrench protrudes from both sides of base housing. It may be necessary to rotate spindle by hand to align hole in spindle with holes in housing.
17 3. DISCONNECT TOOL FROM POWER SOURCE. 4 . Firmly grasp motor housing being sure switch is in the “OFF” position. 5. Verify bit is clear of foreign objects and cord will not “hang up” on any obstructions. 6. Be sure workpiece is firmly held in place.
18 UNDERSCRIBE 7320 TRIMMER ASSEMBL Y The Underscribe Trimmer Base is assembled to the Model 7301 Trimmer Motor as follows: NOTE: The 43109 Trim Bit must be installed into the Trimmer Motor before attaching the motor to the Underscribe Base. DISCONNECT TOOL FROM POWER SOURCE.
19 bottoms. Then pull bit out approximately 1 / 8 ". 2 . Depress spindle lock (B) Fig. 14, and rotate collet nut (C) clockwise by hand until lock engages hole in motor spindle. 3 . While holding spindle lock engaged, tighten collet nut securely by turning clockwise using wrench provided.
20 If joint to TOO TIGHT (laminate will not snap into place), turn eccentric counterclockwise. 4. Repeat Steps 1 through 3 as required to achieve a good fit- up. USING THE UNDERSCRIBE TRIMMER The bottom plate of the Underscribe Trimmer has a guide lip (see Fig.
21 5. Position the underscribe trimmer onto the face frame so that the top (see Fig. 19), is against the edge of the stile. NOTE: The trimmer should be to the right of the rail, so that the cutting action will move from right to left (see Fig. 19). 6.
22 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.
23 SERVICE REPLACEMENT P ARTS When servicing use only identical replacement parts. SERVICE AND REP AIRS All quality tools will eventually require servicing or replacement of parts due to wear from normal use.
24 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase.
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Porter-Cable MODEL 7310 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Porter-Cable MODEL 7310 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Porter-Cable MODEL 7310, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Porter-Cable MODEL 7310 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Porter-Cable MODEL 7310, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Porter-Cable MODEL 7310.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Porter-Cable MODEL 7310. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Porter-Cable MODEL 7310 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
