Manuel d'utilisation / d'entretien du produit WNL-9500 du fabricant Planet Technology
Aller à la page of 61
802.1 1n W ireless PCI Express Adapter WNL-9500 User ’ s Manual V ersion: 1.00 Date: November 2007.
Copyright Copyright © 2007 by PLANET T echnology Corp. All rights reserved. No part of this publication may be reproduced, tran smitted, transcribed, stored in a retrieval system, or translated into .
equipment. This device complies with Part 15 of the FCC Ru les. Operation is subject to the Following two conditions: ( 1 ) This device may not cause ha rmful interference, and ( 2 ) this Devi ce must accept any interference received, including in terference that may cause und esi red operation.
municipal waste and have to co llect such WEEE sep arately . Revision User ’s Manual for PLANE T 802.1 1n Wireless P CI Expre ss Adapter Model: WNL-9500 Rev: 1.
C A T A L O G Chapter 1: Introduction ................................................................................ 6 1-1 Features ......................................................................................................... 6 1-2 Safety Information .
Chapter 1: Introduction For higher wirele ss transfer perfo rmance, we are glad to introduce th e PLANET 802.11n wireless PCI Express adapter – WNL-9500.
z QoS function: Control the bandwid th required for dif ferent applications z Support of most popular operating syst em s in cluding Windo ws 20 00 / XP / 2003 server and Vist a z Smart Antenna T echn.
1-3 S pecification Interface PCI Express 1.0a – x1 PCI Express St andards Conformance Compliant with 802.1 1b / 802.1 1g / 802.1 1n (draft 2.0) Data T ransfer R ate IEEE 802.
1-5 Hardware Intro 2 1 3 4 / 5 1. PCI Express Interface 2. WPS Button 3. Antenna Connectors (3x) 4. ‘Link’ LED 5. ‘Tx/Rx’ LED LED Name Light S tatus Description On Linked to a wireless acce ss.
Chapter 2: Installation 2-1 Hardware Installation 1. SWITCH THE COMPUTE R OFF , remove the cover and insert the wireless network card into an empty PCIe slot of your computer .
4. T o improve radio reception, please adjust antennas to the position s hown in the picture. Rear view T op view.
Side view 2-2 Utility Installation Note 1: If you had ever inst alled the other Wi rel ess Cards before, please uninstall the existed drivers and utilities first. Note 2: The install ation below is perform ed in Windows XP system. The installation s in Windows 2000 and V ista are silimar .
4. Read the License Agreement carefully . Click “Y es” to accept it and continue. 5. It is suggested to use “PLANET Configuration T ool”, which provides fully access to all functions, to manage the WNL-9 500.
devices. If you want to keep comp atibility and communicate with older wireless devices, please select ‘Optimize for WiFi Mode’. After you finish the selection, pl ease click ‘Next’ to continue. If you see ‘Found Ne w Hardware’ message agai n, please ign ore it and wait.
.
Chapter 3: General Configuration The Configuration Utility appears as an icon o n the system tray of Windows while the card is running. Y ou can open the utility by double-click on the icon. Right click the icon; there are some items for you to operate the configuration utility .
Parameter Description Profiles List The profiles list display all t he profiles and the relative setting s of the profiles including Profile Name, SSID, Channel, etc. This sign indicates the activated profile is been connecting. This sign indicates the acti vated profile i s not been connecting.
And you can set the param eter for this profile here:.
Parameter Description Profile Name Define a recognizable profile name for you to identify the dif ferent networks. SSID The SSID (up to 32 print able ASCII characters) is the unique name identified in a WLAN. The ID prevent s the unintentio nal merging of two co-located WLANs.
station in the Wireless LAN network with out through an Access Point or Router . Preamble The preamble defines the length of the CRC blo ck for communication among wireless devices. This o ption is only active in the Ad Hoc network. There are two modes including Auto and Long Preamble.
Authentication T ype This setting has to be consi stent with the wireless networks that the card intends to connect. Open – No authentication is needed among the wi reless network. Shared – Only wireless devices using a sha red key (WEP Key identified) are allowed to connecting each other .
their access point or gateway , as well as in each wireless st ation in the network. WP A-PSK takes over automatic ally from that point, keeping unauthorized use rs that don't have the ma tching pa ssword from joining th e network, while encrypting the dat a tr aveling between authorized devices.
Fill the text box by following the rules below . 64-bit – Input 10-digit Hex values (in the “A -F ”, “a-f” a nd “0-9” range) o r 5-digit ASCII characters (including “a-z” and “0-9”) as the encryption keys. For example: “0123456aef“ or “test1 ”.
check ( ) before its name. If the wireless a ccess point is not rea chabl e, a red check ( ) will be displayed before it s name. If you want to change the connection p arameters of a spe cific p rofil e, just select it and click ‘Edit’ button, you’ll be prompted to input the c onnection parameters, just like you’re cre ating a new profile.
TLS/Smart Card –TLS is the most secure of the EAP protocols but not D5-Challenge – MD5-Challen ge is the easiest EAP T ype. It requires easy to use. It requires that digit al certificates be exchanged in the authentication phase. The serv er present s a certificate to the client.
3-1-3 Using 802.1x - CA Server If you want to use CA server , please click ‘CA Server ’ tab. And the following message will be displayed: Parameter Description Use Certificate Chain When the EAP a.
Server name must match exactly When selected, the server name must match exactly the serve r name found on the certificat e. Domain name must end in specified name When selected, the serv er name field identifies a domain. The certificate must use a server name b elonging to this domain or t o one of its sub-do mains (e.
Authentication and Network T ype. If you want to connect to any networks on the list, double-cli ck the item on the list, and the card will automatically connect to the selected network. Rescan Button Click “Rescan” button to collect the new information of all the wireless networks nearby .
If the access point you selected doe s n ot enable e ncryption and d oes not require authentication, please skip this step. 5. Y ou’ll see ‘Connected <-> SSID’ (‘SSID’ is the SSID of the AP you connected to) message displayed at lower-lef t corner of configuration utility .
3-3 V iew Network Link S tatus and S t atistics The configuration utility provides informat ion about net work statistics and lin k st atus. 3-3-1 Link S tatus.
Parameter Description S tatus Display the SSID and MAC ID of t he network the card is connecting to. Extra Info Display the link status. Channel Display the number of the radi o channel and the frequency use d for the networking. Link S peed (Mbps) Display the transmissi on and reception rate of the network.
Signal S trength This bar shows the signal st rength level. The higher percent age shown in the bar , the more radio signal been received by the card. This indicator helps to find the proper po sition of the wireless device for quality network operation.
3-4 Advanced Settings Parameter Description Wireless Mode 802.1 1 B/G/N mix – If you have a mix of 802.1 1b, 802.1 1g, and 802.1 1n wireless st ations in your network, It is to maximize wireless compatibility with wireless access p oints and other wireless devices.
Wireless Protection If you have a mix of 802.1 1b and 802.1 1g wireless st ations in the n etwork, it is recommended to enable the protection mech anism. This mechanism can decrease the rate of data colli sion between 802.1 1b and 802.1 1g wireless st ations.
T urn on CCKM During normal operation, LEAP-enabled client devices mutually authenticate with a new access point by performing a complete LEAP authentication, including communicatio n with the main RADIUS server .
3-5 QoS Setting This wireless network card provide s QoS (Qualit y of Service) function, which can improve the performance of cert ain network applications, like audio / video streaming, network telephony (V oIP), and others.
Setting... Click this button to select the WMM dat a type which will suppress the function of power saving. When this kind of data is transferring, power saving functi on will be disabled. Available dat a types are AC_BK (Background / Lo w Priority), AC_BE (Best Effort), AC_VI (Video First), and AC_VO (V oice First).
3-6-1 WPS Setup - PBC (Push-Button Configuration) 1.Set ‘Config Mode’ to ‘Enrollee’, and then push the ‘WPS’ button on your wi reless access point (the button used to activate WPS standby mode may have an other na me), or use other way to start WPS st andby mode as the instru cti on given by your wireless acce ss point’s user manual.
2. Before you start to est ablish the wireless connection by using WPS, you can click ‘Rescan ’ button to search for WPS -enabled access point s near you, to make sure the WPS function of your access point is activated.
3.All access point s found will be displayed. Pleas e make su re th e access point you wish to connect is displayed. If not, please click ‘Res can’ few more times. Y ou can also click ‘Information’ button to see the detailed information about sele cted access point.
Sometime WPS may fail, and you can click ‘PBC’ button few more times to try again. When an access point is connected, you c an click ‘Dis connect ’ to disconnect your wireless netwo rk card fr.
If you want to delete a found access point from the list, select it and click ‘Delete’ button. 3-6-2 WPS Setup - PIN The PIN number of your WNL-9500 is an eight-dig it number located at the uppe r-right position of configuration utility .
Click ‘PIN’ button now , and wait for few seconds to one minute. If a wireless acces s point with correct PIN code is found, you’ll be connected to that access p oint:.
.
Y ou may have to click ‘PIN’ for few more times to try again. If you still can not connect to access point by this way , please make sure the PIN code you provided to access point is correct.
3-7 About By choosing this option, you can click the hyper link to conn ect the PLANET website. You can also obtain basic information about the WN L-9500 such as the Driver, Utility and EEPROM Version. The MAC Address of the card i s displayed in the screen a s well.
Chapter 4: Soft-AP Function Except becoming a wireless client of other wi reless access points, the WNL-95 00 can a ct as a wireless service provider also! Y ou can swit ch the WNL-9500’s ope rating.
If your computer has a nother n etwork ca rd which is co nnected to Int ernet, please sele ct it from ‘Name’ dropdown menu, and click ‘Enable ICS’; if your computer does not hav e another network card with Internet connection, please click ‘ Not enable ICS’.
Parameter Description SSID Please input the SSID (the name used to identify this wireless access point) here. Up to 32 numerical charact ers can be accepted here, ex cepting space. Channel Please select the wirel ess channel you wish to use. The num ber of channels available here will vary depends on the setting of ‘Country Region Code’.
Use MAC Address Click this b utton to use the MAC address of the wireless ca rd as SSID. A prefix of ‘AP’ will be added. Security Setting Set the security opti ons (w ireles s data encryp tion).
Default Click this button to restore a ll settings in this page back to default value. Apply Click this button to activate c urrent settings. T o exit, click ‘X’ button at the upper-ri ght corner of configuration window .
Encryption T ype Please select an encryptio n mode. The available options in this setting item will vary depending on th e authentication type you select. If you select ‘Not Us e’, data will not be encrypted and people with some netwo rking knowledge will be able to read the data you transfer with pro per tool.
Click ‘Access Control’ tab, and the following messages will appea r: Parameter Description Access Policy Select the policy type of your access rule: Disable: Allow any wireless client with proper authentication settings to connect to this access poin t.
Add A dd the MAC address you inputted in ‘MAC address’ field to the list. Delete Please select a MAC address from the l ist, then click ‘Delete’ button to remove it. Remove all Delete all MAC addresses in the list. Apply Save and apply changes you made.
Parameter Description MAC address Displays the MAC add ress of this wireless client AID The serial number of this wirel ess connection. Power Saving Mode Displays the capability of power-s aving function of this wireless client.
4-5 Event Log This software access poi nt will log all wireless-related activities as a log. Y ou can follow the following instructions to view the content of the event log: Click ‘Event Log’ tab, and the event log will be displayed: Y ou can click ‘Clea r’ to rem ove all entries in the log.
4-6 S tatistics If you want to know detaile d informatio n about ho w your softwa re access point works, you can follow the following instructions to view t he statistics of the acce ss point: Click ‘S tatistics’ tab, and t he event log will be displayed: Y ou can click ‘RESET COUNTERS’ button to reset all counters to zero.
CHAPTER 5: APPENDIX 5-1 T roubleshooting This chapter provides solutions to probl ems usually encountered durin g the installatio n and operation of the adapter . Q. The PLANET WNL-9500 does not w ork properly . A. 1. Right click on My Computer and select Prope rties.
might be necessary to set up one client to es t ablish a BSS (Basic Service Set) and wait briefly before setting up other cli ents. Thi s prevent s several client s from trying to establish a BSS at the same time, which can result in multiple singular BSSs being established, rather than a single BSS with multiple client s associ ated to it.
then present this value to the owner of acce ss point so he / she can add the MAC addre ss of your network card to his / her access point’ s list. Q. The network is slo w / having problem when transferring large files A. 1. Move closer to the place where access point is located.
copies of dat a by multiple antenn a, to improve data transfer performance. By using multiple antennas, not only data transfer rate is impr oved, but also the wireless stability .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Planet Technology WNL-9500 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Planet Technology WNL-9500 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Planet Technology WNL-9500, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Planet Technology WNL-9500 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Planet Technology WNL-9500, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Planet Technology WNL-9500.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Planet Technology WNL-9500. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Planet Technology WNL-9500 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.