Manuel d'utilisation / d'entretien du produit es3012 du fabricant Pelco
Aller à la page of 40
ES3012 Series Esprit ® C306M-K (4/05) ® INST ALLA TION MANUAL.
2 Pelco Manual C306M-K (4/05).
Pelco Manual C306M-K (4/05) 3 CONTENTS Section Page IMPORT ANT SAFETY INSTRUCTIONS ............................................................................ 5 DESCRIPTION .............................................................................
4 Pelco Manual C306M-K (4/05) LIST OF ILLUSTRA TIONS Figur e Page 1 Esprit ES3012 System Dimensions Drawing .................................................... 37 LIST OF TABLES T able Page A Switch Settings for SW1 ..................................
Pelco Manual C306M-K (4/05) 5 IMPOR T ANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer ’s instructions.
6 Pelco Manual C306M-K (4/05) DESCRIPTION The Esprit ® ES3012 Series Integrated Positioning System is available as a basic system or as an ImagePak ® camera and lens package. The basic system integrates a pan and tilt, camera enclosure, and receiver (camera and lens not included).
Pelco Manual C306M-K (4/05) 7 INST ALLA TION The basic ES3012 system does not include a camera and lens package. Therefore you must install a camera and lens in the enclosure before mounting the pan/tilt to the base of the system. CAMERA AND LENS INST ALLA TION (Skip this section if you are installing an ES3012 ImagePak camera and lens package.
8 Pelco Manual C306M-K (4/05) A B 3 Attach the camera and lens to the mount. Extend the lens to the maximum length before positioning the camera and lens.
Pelco Manual C306M-K (4/05) 9 P AN AND TIL T INST ALLA TION 1 When installing the ES3012 Esprit system, allow for sufficient clear- ance between the top of the unit and overhead obstructions. This will prevent interference when the en- closure is driven to its maximum el- evation of 40 degrees.
10 Pelco Manual C306M-K (4/05) 4 Route the wires and cables through the center of the Esprit mount. Re- install the transformer module into the base. The transformer module can be positioned in the mount base in only one orientation. 5 ES3012-5 Model Only – Set the 120/230 voltage selector switch on the trans- former to the appropriate voltage.
Pelco Manual C306M-K (4/05) 11 8 T urn on the power . If the red LED lights, turn off the power and proceed to the next step. If the red LED does not light, refer to the T roubleshooting section.
12 Pelco Manual C306M-K (4/05) TXB SERIES TRANSLA TOR BOARD INST ALLA TION (OPTIONAL) Pelco’s TXB Series allows controllers from other companies to communicate with the Esprit system. T o install a TXB Series board, remove the left cover of the pan and tilt.
Pelco Manual C306M-K (4/05) 13 T o reinstall the pan and tilt cover, do the following: 1. Properly position the cover and slide it into place. The sides of the cover must fit under the front and back rain guards of the pan and tilt, and the top of the cover must seat against the lip of the top gasket.
14 Pelco Manual C306M-K (4/05) OPERA TION POWER-UP DISPLA Y When the Esprit system is powered up or reset, the selected protocol, revision number , and other information is displayed on the monitor .
Pelco Manual C306M-K (4/05) 15 P AN, SCAN, AND TIL T SPEEDS Pan and scan speeds are adjustable from 3 to 40 degrees per second through the pro- gramming menu. The tilt speed is one-half of the pan speed. LENS FUNCTIONS Lens zoom, focus, and iris functions are operated from the controller .
16 Pelco Manual C306M-K (4/05) PROGRAMMING ESPRIT MENUS T o access the main menu, program preset 95. T o make selections in the main menu, use the following controls: Joystick: Move up or down to position cursor or to toggle between selections. Iris Open: Enter .
Pelco Manual C306M-K (4/05) 17 ACCESSING MAIN MENU (PRESET 95) Y ou can call up the main menu on your monitor by programming (setting or creating) preset 95 (28 if in 32-preset mode). Programming preset 95 for Pelco’s controllers varies according to the type of controller you are using.
18 Pelco Manual C306M-K (4/05) AZ/EL Other Menu Park Time 0 Pan/Scan Spd 7 Power Up Default Pat length 6 min Spd Profile 50 MPH wind <Zone Blank> <Az /El/ Direction> Exit Az/El/Direction S.
Pelco Manual C306M-K (4/05) 19 AZ/EL LINE Az/El Line controls the vertical display position of the Azimuth/Elevation label. The label may be displayed on lines 3 through 10. Line 3 is the third line from the top of the screen and line 10 is located at the bottom of the screen.
20 Pelco Manual C306M-K (4/05) AZIMUTH ZERO Azimuth is the pan angle from 0 ° to 359 ° . Azimuth zero is the programmed 0 ° point that is normally set to magnetic north. Once programmed, on-screen pan position (azimuth) and compass readings are based on the set azimuth zero point.
Pelco Manual C306M-K (4/05) 21 DIRECTION Direction programs the horizontal display position of the Direction label (N, NW , NE, …). The following settings are available for the Direction label: Off – Label is not displayed. Left – Label is displayed on the left-hand side of the screen.
22 Pelco Manual C306M-K (4/05) DIRECTION LINE NOTE: Direction display is not available while you are programming or running a pattern. Other Menu Park Time 0 Pan/Scan Spd 7 Power Up Default Pat length.
Pelco Manual C306M-K (4/05) 23 DISPLA Y DURA TION Display Duration programs the duration the Az/El, Direction, and Zoom labels are displayed on the monitor . The available settings for display duration include the following: CONST ANT - The label is displayed continuously .
24 Pelco Manual C306M-K (4/05) LIMIT STOPS TURNING LIMIT STOPS ON OR OFF T o change the limit stop mode: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Limits. 3. Press the Iris Open button to enter the Limits menu.
Pelco Manual C306M-K (4/05) 25 Scan Limit Stops When scan limit stops are set, the pan and tilt reverses direction during random, frame, or auto scanning when a limit stop is reached.
26 Pelco Manual C306M-K (4/05) P AN/SCAN SPEED The pan/scan speed is adjustable from 3-40 degrees per second. This occurs in three scan modes: auto, random, and frame scan. T o change the pan/scan speed: 1. Program preset 95 (28). The main menu appears.
Pelco Manual C306M-K (4/05) 27 POWER-UP MODE This feature lets the system resume a desired condition following power-up. The menu in- cludes the following choices. • Default - On power-up, the pan and tilt goes through a configuration cycle and stops at zero reference, showing “Configuration Done,” address, and mode settings on the screen.
28 Pelco Manual C306M-K (4/05) SPEED PROFILE This feature allows the operator to set the wind speed conditions for the location of the system. Y ou can set two wind speed profiles of 50 mph or 90 mph in which the system will remain operational. In both settings, the pan speed will be a maximum of 40 degrees per second.
Pelco Manual C306M-K (4/05) 29 ZONES Basic rules for setting zones: 1. Refer to the documentation for your control system to program zones. 2. Establish zones using the controller , prior to programming ZONE BLANK with the Es- prit onscreen menu. 3. T o accurately set zone areas, zoom wide to the maximum field of view.
30 Pelco Manual C306M-K (4/05) TROUBLESHOOTING Symptom: System does not operate. 1. Check system input voltage. 2. Check for proper positioning of input power select switch for the transformer (ES3012-5 models only). 3. The Esprit system is protected by a resettable overcurrent protective device located in the transformer module.
Pelco Manual C306M-K (4/05) 31 Symptom: No video or poor video 1. Check the video and power connections to the camera. 2. Check for power to the camera from the Esprit system camera power output. 3. Check all coax BNC connectors from the camera to the monitor .
32 Pelco Manual C306M-K (4/05) APPENDIX NOTE: Esprit will sense and automatically select input from Coaxitron control signals in either the standard or extended mode. Therefore, the DIP switches settings have no effect on Coaxitron control signals. T able A.
Pelco Manual C306M-K (4/05) 33 T able B. Switch Settings for SW2 NOTE: The Esprit will sense and automatically select input from Coaxitron control signals in either the standard or extended mode. Therefore, the DIP switches settings have no effect on Coaxitron control signals.
34 Pelco Manual C306M-K (4/05) T able B. Switch Settings for SW2 (continued) (Continued on next page) Receiver Address Switch Setting P-T ype D-Type Control Control SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6.
Pelco Manual C306M-K (4/05) 35 T able B. Switch Settings for SW2 (continued) Receiver Address Switch Setting P-T ype D-Type Control Control SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 – 232 OFF .
36 Pelco Manual C306M-K (4/05) SPECIFICA TIONS ELECTRICAL Input Voltage: 24 or 120/230 V AC, 50/60 Hz; on ES3012-5 models, a switch is installed on the transformer module located in the mount base to make 120 or 230 V AC input voltage selection. Reset feature enabled when power becomes unstable or interrupted.
Pelco Manual C306M-K (4/05) 37 Figure 1. Esprit ES3012 System Dimensions Drawing 13.8 (35.1) 4.1 (10.5) 14.0 (35.5) 4.8 (12.3) 9.1 (23.2) 7.7 (19.7) 6.9 (17.5) 7.9 (20.2) 16.4 (41.7) 5.2 (13.3) NOTE: V ALUES IN P ARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES.
38 Pelco Manual C306M-K (4/05) REGULA TORY NOTICES This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reason- able protection against harmful interference in a residential installation.
Pelco Manual C306M-K (4/05) 39 Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy , and Spectra are registered trademarks of Pelco. ©Copyright 2005, Pelco. Endura and ExSite are trademarks of Pelco. All rights reserved. Lexan is a registered trademark of the General Electric Company .
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Pelco es3012 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Pelco es3012 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Pelco es3012, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Pelco es3012 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Pelco es3012, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Pelco es3012.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Pelco es3012. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Pelco es3012 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
