Manuel d'utilisation / d'entretien du produit C2423M (5/00) du fabricant Pelco
Aller à la page of 28
SD5BCBW Series Spectra II™ Color/Black & White Dome Systems Operation and Programming Manual C2423M (5/00) ® P elco • 3500 P elco Wa y • Clovis , CA 93612-5699 USA • www .
2 Pelco Manual C2423M (5/00) CONTENTS Section Page IMPORT ANT SAFEGU ARDS AND W ARNINGS ................................................................ 3 OPERA TION .....................................................................................
Pelco Manual C2423M (5/00) 3 IMPOR T ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be obser v ed. 1. Installation and ser vicing should only be done by qualified service personnel and conform to all local codes.
4 Pelco Manual C2423M (5/00) OPERA TION POWER-UP DISPLA Y When the Spectra II™ dome is pow ered up, the selected protocol, re vision number , and other inf or mation is display ed on the monitor .
Pelco Manual C2423M (5/00) 5 OPERA TING NOTES P AN AND TIL T FUNCTIONS Controller T ype Pan Tilt Fixed speed Speed determined by controller Speed determined by controller Va r iable speed 0.
6 Pelco Manual C2423M (5/00) PA TTERNS The Spectra II dome can do either one full pattern (1.5, 3, or 6 minutes long) or two half patterns (.75, 1.5, or 3 minutes long). This patter n can consist of any standard pan and tilt or lens command. Presets, flip, and turbo are not allowed in a pattern.
Pelco Manual C2423M (5/00) 7 AUXILIAR Y OUTPUTS An A UX 1 command from the controller will activate the rela y in the dome and operate the de vice that is connected to the relay .
8 Pelco Manual C2423M (5/00) PROGRAMMING Programming Guide - Spectra II Color/Black & White 1. Access main menu (preset 95). 2. Make main menu selections . Joystic k: Move up or do wn to position cursor or to toggle between selections. Iris Open: Enter Iris Close: Cancel PRESETS The follo wing presets are reserved for special functions .
Pelco Manual C2423M (5/00) 9 ACCESSING MAIN MENU (PRESET 95) Y ou can call up the main menu on your monitor b y programming (setting or creating) preset 95 (28 if in 32-preset mode). Programming preset 95 f or P elco’ s controllers varies according to the type of controller you are using.
10 Pelco Manual C2423M (5/00) ALARMS The Spectra II dome has se ven alarm inputs, which can be designated as either high or low prior ity . The high prior ity setting is significant when more than one alarm is activated. If priority in alarms is not required, leave all alarms in the low setting.
Pelco Manual C2423M (5/00) 11 6. P osition the cursor (>) beside the number of the alarm input for which you w ant to set the pattern. 7. Press the Iris Open button. The cursor mov es to the right, beside the words Full Pat, Half P at 1, Half Pat 2, or No P attern.
12 Pelco Manual C2423M (5/00) AUTO FLIP There are two auto flip modes: On - Auto flip mode is enab led. Off - A uto flip mode is disabled. To change the auto flip mode: 1. Program preset 95 (28). The main menu appears . 2. P osition the cursor (>) beside Other .
Pelco Manual C2423M (5/00) 13 AUTO IRIS The following are the settings for auto iris: Mode Level To change the settings for auto iris: 1. Program preset 95 (28). The main menu appears . 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu.
14 Pelco Manual C2423M (5/00) AUTO IR LEVEL The IR lev el setting determines when the IR filter will switch IN or OUT . F ollowing are the av ailable settings f or the Auto IR Le vel: Dusk = 1/60 seco.
Pelco Manual C2423M (5/00) 15 There are two backlight compensation modes: On - The dome uses the center 10 percent of the picture to adjust the iris. If there is a bright light source outside of this area, it will wash out to white. The camera will adjust the iris so that the object in the sensitive area is properly exposed.
16 Pelco Manual C2423M (5/00) Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Camera Menu Backlight comp Off Zoom limit x72 Reset .
Pelco Manual C2423M (5/00) 17 Next Menu Slow shutter mode Auto Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpness> <White balance> Previous Exit Main Menu <Camera> .
18 Pelco Manual C2423M (5/00) NOTE: Programming preset 90 (23) disables the manual limit stops until preset 91 (24) is set. TURNING LIMIT STOPS ON OR OFF To change the limit stop mode: 1. Program preset 95 (28). The main menu appears . 2. P osition the cursor (>) beside Other .
Pelco Manual C2423M (5/00) 19 LINE SYNC PHASE - The cursor mov es to a numeric value. Mo ve the joystic k up or down to change the value . Press the Ir is Open b utton to select the choice. The value represents the phase angle in tenths of a degree between 0 degrees and 359 degrees.
20 Pelco Manual C2423M (5/00) Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Other Menu A uto flip On Proportional pan On Limit stops Off Park time minutes 0 Scan speed deg/s 25 Pattern length 1.
Pelco Manual C2423M (5/00) 21 3. Press the Iris Open button to enter the Other menu. 4. Position the cursor (>) beside Proportional Pan. 5. Press the Iris Open button. The cursor mov es to the right, beside the word On or Off. 6. Mov e the joystick up or do wn to toggle between On and Off.
22 Pelco Manual C2423M (5/00) SCAN SPEED Next Menu Slow shutter mode Auto Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpness> <White balance> Previous Exit Main Menu <.
Pelco Manual C2423M (5/00) 23 SHUTTER SPEED Next Menu Slow shutter mode Aut o Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpness> <White balance> Previous Exit Main Menu .
24 Pelco Manual C2423M (5/00) SLOW SHUTTER MODE Next Menu Slow shutter mode Aut o Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpness> <White balance>* Previous Exit Main .
Pelco Manual C2423M (5/00) 25 WHITE BALANCE Next Menu Slow shutter mode Auto Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpness> <White balance> Previous Exit Main Menu &.
26 Pelco Manual C2423M (5/00) NOTE: The Spectra II Color/Black and White camera cannot do electronic zoom in a pattern. Optical zoom will operate in a pattern.
Pelco Manual C2423M (5/00) 27 SPECIFICA TIONS MECHANICAL Pan Movement: 360 ° continuous pan rotation Ve r tical Tilt: Unobstructed +2 ° to -92 ° Manual P an/Tilt Speeds* Pan: 0.
28 Pelco Manual C2423M (5/00) P elco, the P elco logo , Camclosure, Esprit, Genex, Legacy , and Spectra are registered trademarks of Pelco . © Cop yright 2000, P elc o. Endura and ExSite are trademarks of P elco. All rights reser ved. U .S. P atent No.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Pelco C2423M (5/00) c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Pelco C2423M (5/00) - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Pelco C2423M (5/00), vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Pelco C2423M (5/00) va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Pelco C2423M (5/00), mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Pelco C2423M (5/00).
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Pelco C2423M (5/00). Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Pelco C2423M (5/00) ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
