Manuel d'utilisation / d'entretien du produit c1487-c du fabricant Pelco
Aller à la page of 50
Pelco • 300 W. Pontiac Way, Clovis • CA 93612-5699 USA • Pelco Online @ http://www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 • DataFAX (800) 289-9108 Inte.
2 Pelco Manual C1487M-C (7/99) CONTENTS Section Page GENERAL .......................................................................................................................... 4 IMPORT ANT SAFEGUARDS AND WARNINGS ..............................
Pelco Manual C1487M-C (7/99) 3 Section Page LIMIT ST OPS .................................................................................................... 41 PARK TIME MINUTES ........................................................................
4 Pelco Manual C1487M-C (7/99) GENERAL IMPORT ANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.
Pelco Manual C1487M-C (7/99) 5 COMP ASS TOOL SAFETY BRACKET CONDUIT FITTING & LOCK NUT T -RAIL CLIP Figure 2. Back Box Parts Figure 1. In-Ceiling Components BACK BOX DOME DRIVE LOWER DOME IN-CEILI.
6 Pelco Manual C1487M-C (7/99) BACK BOX DOME DRIVE LOWER DOME Figure 3. Pendant Components PENDANT MODELS The Spectra II™ dome and Spectra Lite™ dome shipping cartons contain three boxes, plus the C1487M-C system manual that covers everything in the system (back box, dome drive, and lower dome).
Pelco Manual C1487M-C (7/99) 7 DESCRIPTION Spectra II™ and Spectra Lite™ domes are capable of the following: • 360 ° pan rotation • preset positioning • +2 to -92 ° tilt • variable speed The in-ceiling models can be installed in hard ceilings or standard 2' x 2' (61 cm x 61 cm) suspended ceilings.
8 Pelco Manual C1487M-C (7/99) SPECTRA LITE™ PENDANT COMPONENTS BB5T-PB Black pendant-mount back box (CE, UL, cUL) BB5T-PG Light gray pendant-mount back box (CE, UL, cUL) BB5T-PG-E Same as BB5T-PG e.
Pelco Manual C1487M-C (7/99) 9 SUSPENDED CEILING 1. Remove the ceiling tile from the ceiling. (The ceiling tile cannot be thinner than 0.50 inch [1.27 cm] nor thicker than 1.75 inches [4.45 cm].) 2. Locate the center point to drill a hole in the tile.
10 Pelco Manual C1487M-C (7/99) WIRING Bring wiring to the back box opening in the ceiling. Do not attach the wiring to the back box. Y ou will do that later . Refer to Figure 8 for the Spectra II™ wiring diagram or Figure 9 for the Spectra Lite™ wiring diagram.
Pelco Manual C1487M-C (7/99) 11 Figure 9. Wiring Diagram for Spectra Lite™ CONTROL (RS-422) SPECTRA LITE™ INTERCONNECT BOARD If you are using a Coaxitron ® controller , the control signals to operate the dome drive will be transmitted over the video coax.
12 Pelco Manual C1487M-C (7/99) T able B. 24 V AC Wiring Distances The following are the recommended maximum distances for 24 V AC with a 10-percent voltage drop.
Pelco Manual C1487M-C (7/99) 13 BACK BOX CONNECTIONS Refer to Figure 12 or 13 to attach the wiring to the interconnect circuit board inside the back box. Also refer to Figure 8 or 9 if necessary . 1. Ear th Gr ound - Connect earth ground to the middle connector on the power connector .
14 Pelco Manual C1487M-C (7/99) Figure 13. Interconnect Circuit Board Electrical Connections for Spectra Lite™ HTR/F AN RX– RX+ TX– TX+ PWR IN FUSE 1.6 A DOME DRIVE CONNECTOR RS-422 CONTROL SIGNALS POWER (24 V AC ONL Y) FA N 24 V AC MIDDLE PIN IS GND VIDEO CONNECTOR FOR OPTIONAL TRANSLA TOR SUBASSEMBL Y 5.
Pelco Manual C1487M-C (7/99) 15 DOME DRIVE 1. T urn on power to the back box. The red LED should light to indicate power. If the LED does not light, correct the trouble before proceeding.
16 Pelco Manual C1487M-C (7/99) T able D. Switch Settings for SW2 – P-T ype Control NOTES: For Coaxitron ® controls, all switches on SW2 MUST be OFF .
Pelco Manual C1487M-C (7/99) 17 T able E. Switch Settings for SW2 – D-T ype Control NOTES: For Coaxitron ® controls, all switches on SW2 MUST be OFF .
18 Pelco Manual C1487M-C (7/99) T able E. Switch Settings for SW2 – D-Type Control (continued) Receiver Address Switch Setting SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 57 ON OFF OFF ON ON ON .
Pelco Manual C1487M-C (7/99) 19 T able E. Switch Settings for SW2 – D-T ype Control (continued) Continued on next page 1 17 ON OFF ON OFF ON ON ON OFF 1 18 OFF ON ON OFF ON ON ON OFF 1 19 ON ON ON O.
20 Pelco Manual C1487M-C (7/99) T able E. Switch Settings for SW2 - D-T ype Control (continued) Continued on next page 177 ON OFF OFF OFF ON ON OFF ON 178 OFF ON OFF OFF ON ON OFF ON 179 ON ON OFF OFF.
Pelco Manual C1487M-C (7/99) 21 T able E. Switch Settings for SW2 - D-T ype Control (continued) 237 ON OFF ON ON OFF ON ON ON 238 OFF ON ON ON OFF ON ON ON 239 ON ON ON ON OFF ON ON ON 240 OFF OFF OFF.
22 Pelco Manual C1487M-C (7/99) INST ALLA TION FOR PENDANT MODELS PENDANT -MOUNT INST ALLA TION 1. Install the pendant dome mount. Refer to the instructions supplied with the mount. If the mount is outdoors, make sure it is properly sealed to keep moisture out.
Pelco Manual C1487M-C (7/99) 23 10. If you are installing an outdoor model, plug the two-pin heater connection in the lower dome into the mating connector in the back box. 1 1. Remove the two screws and the tube of Loctite ® from the parts bag. Apply a drop of Loctite ® to each screw .
24 Pelco Manual C1487M-C (7/99) POWER-UP DISPLA Y When the Spectra II™ dome or Spectra Lite™ dome is powered up or reset, the selected protocol, revision number , and other information is displayed on the monitor . For example, the screen might show the following information: PELCO SPECT II 4.
Pelco Manual C1487M-C (7/99) 25 ZOOM SPECTRA II™ ZOOM The Spectra II™ dome can magnify an object up to 128 times. The dome has 16X of optical zoom and 8X of electronic (digital) zoom for 128X total zoom. The amount of zoom can be set for 16X, 32X, 64X, or 128X.
26 Pelco Manual C1487M-C (7/99) RANDOM, FRAME, AND AUTO SCANNING Program preset 97 (30) to start random scanning. Program preset 98 (31) to activate frame scanning (three seconds of scanning followed by a three-second pause). Program preset 99 (32) to start auto (continuous) scanning.
Pelco Manual C1487M-C (7/99) 27 In certain situations, the dome will respond as follows: • If a preset has not been set, but an alarm is connected: the dome will go to a factory preset that will not be the desired position. • If one alarm is a preset and another is a pattern and both are received: the dome will alternate between them.
28 Pelco Manual C1487M-C (7/99) PROGRAMMING THE SPECTRA II™ AND SPECTRA LITE™ The Spectra II™ and Spectra Lite™ domes can be programmed for the following functions.
Pelco Manual C1487M-C (7/99) 29 MAIN MENU ACCESS Y ou can call up the main menu on your monitor by programming (setting or creating) preset 95 (28 if in 32-preset mode; refer to the Preset Functions section). Programming preset 95 for Pelco’s controllers varies according to the type of controller you are using.
30 Pelco Manual C1487M-C (7/99) 3. Press the Iris Open button to enter the Camera submenu. 4. Move the joystick up or down to position the cursor beside Backlight Comp. 5. Press the Iris Open button on your keyboard. A star will appear beside Backlight Comp and the cursor will move to the right beside the word On or Off.
Pelco Manual C1487M-C (7/99) 31 T urning off power to the Spectra II™ and Spectra Lite™ domes does not reset the camera. Camera settings are retained in memory , and when the power is turned back on, the settings will be the same as they were when it was turned off.
32 Pelco Manual C1487M-C (7/99) Gain The gain adjusts the signal level of the video output. Increasing the gain in low light conditions will increase the level of noise in the picture.
Pelco Manual C1487M-C (7/99) 33 PEAK - The cursor moves to a numeric value. Increasing this value will cause the auto iris circuit to react more to highlights or “peaks” in the picture. Decreasing this value will cause it to use the average video level to adjust the iris.
34 Pelco Manual C1487M-C (7/99) AUTO-FOCUS MODE (This section applies to Spectra II™ only .) There are two auto-focus modes: auto and off. If auto focus is in the auto mode, pressing the Focus Far or Focus Near button will place the focus in the manual mode.
Pelco Manual C1487M-C (7/99) 35 AUTO SHARPNESS - The cursor moves to one of two choices: On or Off. Move the joystick up or down to toggle between them. Press the Iris Open button to select the choice, or press the Iris Close button if you do not want to change the setting.
36 Pelco Manual C1487M-C (7/99) 2. If the cursor (>) is not beside Line Sync, move the joystick up or down to position the cursor beside Line Sync. 3. Press the Iris Open button on your keyboard. Another menu will appear with the Line Sync and Line Sync Phase selections.
Pelco Manual C1487M-C (7/99) 37 T o select the power-up mode: 1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to access the main menu (refer to the Main Menu Access section).
38 Pelco Manual C1487M-C (7/99) 6. Move the joystick up or down to toggle between On or Off. 7. SELECT - Press the Iris Open button on your keyboard to select your choice. CANCEL - Press the Iris Close button if you do not want to change the setting. ALARM DWELL (This section applies to Spectra II™ only .
Pelco Manual C1487M-C (7/99) 39 ALARM PA TTERN (This section applies to Spectra II™ only .) In response to an alarm, the Spectra II™ dome can do either one full pattern (1.5, 3, or 6 minutes long) or two half patterns (.75, 1.5, or 3 minutes long).
40 Pelco Manual C1487M-C (7/99) AUTO FLIP There are two auto flip modes: on or off. When the auto flip mode is on, the auto flip feature is enabled. When it is off, the feature is disabled.
Pelco Manual C1487M-C (7/99) 41 LIMIT STOPS There are two types of limit stops: Manual limit stops Scan limit stops When manual limit stops are set, a manual (joystick) pan operation will stop when a limit stop is reached.
42 Pelco Manual C1487M-C (7/99) PARK TIME MINUTES This feature causes the dome to park at preset 1 after a programmed number of minutes of control inactivity . The time can be set from 1 minute to 720 minutes (12 hours), or it can be set to zero, which disables this feature.
Pelco Manual C1487M-C (7/99) 43 3. Press the Iris Open button to enter the submenu entitled Other . 4. Move the joystick up or down to position the cursor beside Pattern Length. 5. Press the Iris Open button. The cursor will move to the right beside the number of minutes (1.
44 Pelco Manual C1487M-C (7/99) d. T urn on power. If the unit still does not operate, turn off power and replace the dome drive with a unit that is good, if you have a spare. Check the switch settings on the substitute dome drive before installing it.
Pelco Manual C1487M-C (7/99) 45 BACK BOX ELECTRONIC ASSEMBL Y REMOV AL T o remove the back box electronic assembly: 1. T urn of f power . 2. Open the interconnect door and disconnect all wiring to the back box. 3. Use an 1 1/32 socket driver to remove the three 8-32 washers and nuts that hold the electronic assembly to the back box.
46 Pelco Manual C1487M-C (7/99) SPECIFICA TIONS MECHANICAL Construction Back box: Aluminum Dome drive: Aluminum, ABS plastic Lower dome: Acrylic Cable Entry In-Ceiling: .
Pelco Manual C1487M-C (7/99) 47 Ratings: NEMA Type 1–In-ceiling back boxes, all dome drives NEMA Type 4–Pendant back boxes IP 66–Pendant back boxes Weight Unit Shipping In-Ceiling Back Box: 2.6 lb (1.18 kg) 4 lb (1.81 kg) Dome Drive: 2.65 lb (1.
48 Pelco Manual C1487M-C (7/99) Effective Pixels (NTSC Spectra II™): 768 (H) x 494 (V) (PAL Spectra II™): 752 (H) x 582 (V) (NTSC Spectra Lite™): 510 (H) x 492 (V) (PAL Spectra Lite™): 500 (H) x 582 (V) Horizontal Resolution (Spectra II™): >450 TV lines (Spectra Lite™): >330 TV lines Lens Minimum f-stop (Spectra II™): F1.
Pelco Manual C1487M-C (7/99) 49 MONOCHROME (Spectra II™ Only) Signal Format EIA (model DD5AM) CCIR (model DD5AM-X) Scanning System: 2:1 interlace Image Sensor 1/4-inch interline transfer CCD Horizontal Resolution: >500 TV lines Effective Pixels EIA: 768 (H) x 494 (V) CCIR: 752 (H) x 582 (V) Lens: Minimum f-stop: F1.
50 Pelco Manual C1487M-C (7/99) REVISION HISTOR Y Manual # Date Comments C1487M 7/98 Original version. C1487M-A 11/98 Revised the manual to incorporate Spectra Lite™ material. Added material on CCIR and EIA monochrome cameras, and P AL color camera.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Pelco c1487-c c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Pelco c1487-c - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Pelco c1487-c, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Pelco c1487-c va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Pelco c1487-c, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Pelco c1487-c.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Pelco c1487-c. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Pelco c1487-c ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
