Manuel d'utilisation / d'entretien du produit Monarch 932TM du fabricant Paxar
Aller à la page of 24
TC0932OI Rev. AC 12/07 ©2004 Paxar Americas, Inc. a subsidiary of Avery Dennison Corp. All rights reserved. Operating Instr uctions Operating Instr uctions 23456 78901 Fishing T ackle $40.00 23456 78901 Fishing T ackle $40.00 23456 78901 Fishing T ackle $40.
Each product and program carries a respective written warranty , the only warranty on which the customer can rely . Paxar Americas reserves the right to make changes in the product, the programs, and their availability at any time and without notice.
T ABLE OF CONTENTS GETTING S T ARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Unpacking the Stacker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ii T able of Contents.
GETTING S T ARTED 1 The Monarch ® 932 stacker works with a Monarch® 9860 printe r . The stacker supports backfeed mode on the printe r . There is no power ON/OFF switch for the stacke r . Once the stacker is plugged into an outlet, it is on.
Step 1 - Installation for the 9860 Printer 1. Locate the screw hole on the stacker mounting plate. 2. Attach the adjusting bracket to the stacker mounting plate using a flanged screw as shown (do not tighten all the way). 3. Gently lift stacker and center the guide tabs in the knife opening.
Step 2 - Level the Stacker 1. Check the distance between the rollers and the knife. Make sure the rollers are not touching the front of the knife or too far from the knife. If incorrect, follow the steps below. If correct, skip this step and move on to Step 3 - Connect the Power Cord.
Step 3 - Connect the Power Cord 1. Plug the power cord into the stacker’s AC inlet. 2. Plug the other end of the power cord into a grounded outlet. Once the power cord is attached to an outlet, the stacker is on. There is no power ON/OFF switch for the stacke r .
Step 4 - Check the Alignment 1. Load supply in the printe r . For more information about loading suppl y , refer to the printer’s Operator’s Handbook or Quick Reference . 2. Set aside the tag weight. 3. Widen the guide rails to maximum width by pulling and extending the guide rails out of the grooves at the bottom of the tra y .
5. Move tag stop up and down by using your thumb to pull out slightly on the release tab and lift up until it stops. Adjust the tag stop to the length of the tags. 6. Make sure the transport lock handle is in the locked position. 7. Make sure supply is loaded and the printer is turned on.
9. Use the cut tags as a guide and adjust the guide rails back into the grooves so that they are barely touching the sides of the tag. Step 5 - Set the T ag Width 1. Set aside the tag. 2. Locate the tag weight. 3. Unlock the tag weight handle by turning the knob counterclockwise.
5. Tighten the knob. 6. Place the tag weight against the tag stop. 7. Print a test batch of 50 tags. The stacker’s LED is on when tags are moving through the stacke r . Step 6 - Set the Belt Speed. 1. Stack the tags in your hand. 2. Hold the stack against the tag gauge on the tag weight.
3. T urn the belt adjustment knob to the number from the stack. 4. Print another test batch of 50 or more. The stacker’s LED is on when tags are moving through the stacke r . Look at how the tags sit in the stacker tra y . If the tags are too: u Tight, turn the belt speed to a higher setting (higher number).
1-10 Getting Started.
HOW TO OPER A TE 2 This chapter describes how to u re-load and change supplies u empty the stacker tray u clear a tag jam u install verifier riser blocks How to Operate 2-1.
Re-Loading or Changing Supplies If you run out of supplies while printing, the printer display or keyboard shows a 756 status code. 1. Press the Feed button to feed the last tags into the stacke r . 2. Load a new roll of supplies. For more information on loading supplies, refer to the printer’s Operator’s Handbook or Quick Reference.
Stacker Running 1. Pick up some of the tags in front of the tag weight. 2. Move the tag weight against the stack. T ry not to push or compress the stack. 3. Continue to remove tags. Clearing a T ag Jam If a tag jams inside the stacke r , the printer and stacker automatically stops.
3. Use the tab to lift the transport. Check for tags. 4. Remove the tags. 5. Lower the transport. 6. Replace the transport lock handle. Make sure it is completely in the hole at the back of the stacke r . T urn the handle down to lock. 7. Press the Escape button to clear the status code.
TROUBLESHOOTING 3 Problem Action Stacker Full or 760 Warning Status Code 1. Empty the stacker tray. 2. Place the tag weight against the tag stop. 3. Press the Escape button to clear the status code. 4. Continue printing. The stacker may not be plugged into an outlet.
3-2 T roubleshooting.
SPECIFIC A TIONS A Stacker Height: 14 inches (355.6 mm) Depth: 7.9 inches (201 mm) Base Width: 24 inches (609.6 mm) T ag Bed: 29.6 inches long (752 mm) Weight: 18 lbs.
Supplies Thickness: .007 inches (.18 mm) minimum .012 inches (.30 mm) maximum Widths: 1.2 inch (30 mm) minimum 4.0 inches (102 mm) maximum Lengths: 1.2 inches (30 mm) minimum 3.66 inches (93 mm) maximum Minimum Stacked T ag Dimensions If a tag is printed width wise: 1.
Each product a nd program ca rries a respe ctive written warranty , the only warranty on wh ich the customer can rely . P axar Ame ricas reserves the righ t to make changes in the produc t, the programs, and their avai labili ty at any time and with out notice.
TC0932OI Rev. AB 12/04 ©2004 Paxar Americas, Inc. All rights reserved. Monarch 932 Stacker.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Paxar Monarch 932TM c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Paxar Monarch 932TM - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Paxar Monarch 932TM, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Paxar Monarch 932TM va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Paxar Monarch 932TM, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Paxar Monarch 932TM.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Paxar Monarch 932TM. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Paxar Monarch 932TM ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
