Manuel d'utilisation / d'entretien du produit PR-DLSW du fabricant Asus
Aller à la page of 130
Motherboard PR-DLSW User Guide.
ii Checklist Copyright © 2002 ASUST eK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, sto.
iii Features Contents FCC/CDC statements ..................................................................... vi Safety information ......................................................................... vii About this guide .......................
iv Safeguards Contents 2.6 Expansion slots ................................................................. 2-1 1 2.6.1 Installing an expansion card ................................. 2-1 1 2.6.2 Configuring an expansion card .........................
v Contents Chapter 5: OS Installation 5.1 Microsoft ® Windows ® NT Server 4.0 ................................... 5-1 5.1.1 LSI® SCSI Driver Installation ................................. 5-1 5.1.2 Intel® 82551QM LAN Driver Installation ..........
vi FCC/CDC st atements Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation.
vii Safety information Electrical safety • T o prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected.
viii About this guide This user guide contains the information you need when installing the ASUS PR-DLSW motherboard. How this guide is organized This manual contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the PR-DLSW motherboard.
ix Conventions used in this guide T o make sure that you perform certain tasks properly , take note of the following symbols used throughout this manual. Where to find more information Refer to the following sources for additional information and for product and software updates.
x ASUS contact infor mation ASUST eK COMPUTER INC. (Asia-Pacific) Address: 150 Li-T e Road, Peitou, T aipei, T aiwan 1 12 General T el: +886-2-2894-3447 General Fax: +886-2-2894-3449 General Email: info@asus.
xi PR-DL SW specifications summar y CPU Chipsets Front Side Bus (FSB) Memory Onboard LAN Onboard SCSI Onboard audio Expansion slots Rear panel I/O Internal connectors BIOS features Support for Intel .
xii PR-DL SW specifications summar y Form Factor Support CD contents Extended A TX form factor: 12 in x 13 in (30.5 cm x 33 cm) Device drivers Utilities Contact information * Specifications are subject to change without notice.
Chapter 1 This chapter describes the features of the PR-DLSW motherboard. It includes brief explanations of the special attributes of the motherboard and the new technology it supports.
ASUS PR-DLSW motherboard Chapter summar y 1.1 W elcome! ........................................................ 1-1 1.2 Package contents .......................................... 1-1 1.3 Special features .............................................
ASUS PR-DLSW motherboard user guide 1-1 1 . 1 Welcome! Thank you for buying the ASUS ® PR-DLSW motherboard! The ASUS PR-DLSW motherboard delivers a host of new features and latest technologies making.
1-2 Chapter 1: Product introduction 1 .3 Special features 1.3.1 Product highlights Latest processor technology The PR-DLSW motherboard supports the Intel ® Xeon p rocessor via du al 604- pin surface mount ZIF sockets .
ASUS PR-DLSW motherboard user guide 1-3 Onboard audio The C-Media CMI8738/PCI-SX audio controller is onboard to provide HTRF-based 3D positional audio (C3DX ™ ) 4-channel audio output.
1-4 Chapter 1: Product introduction 1.3.2 V alue-added solutions T emperature, fan, and voltage monitoring The CPU temperature is monitored by the ASUS ASIC to prevent overheating and damage. The system fan rotations per minute (RPM) is monitored for timely failure detection.
ASUS PR-DLSW motherboard user guide 1-5 Compliance Both the BIOS and the hardware levels of the motherboard meet the stringent requirements for SDG 2.0 certification.
1-6 Chapter 1: Product introduction 1 .4 Motherboard over view Before you install the PR-DLSW motherboard, familiarize yourself with its physical configuration and available features to facilitate the motherboard installation and future upgrades.
ASUS PR-DLSW motherboard user guide 1-7 10 18 1 2 3 7 8 11 12 14 17 19 5 21 4 6 16 13 20 15 9 23 24 28 29 27 26 25 30 22.
1-8 Chapter 1: Product introduction DDR DIMM sockets. These six 184-pin DIMM sockets support up to 12GB system memory using registered ECC PC2100/1600 DDR DIMMs.
ASUS PR-DLSW motherboard user guide 1-9 Ultra-160 SCSI connectors. These dual-channel 68-pin Ultra-160 SCSI connectors support up to 30 SCSI devices, and data transfers of 160Mbps. LSI ® SCSI controller . The LSI 53C1010R SCSI controller supports up to 30 SCSI devices through the onboard dual-channel SCSI connectors.
1-10 Chapter 1: Product introduction LPC super I/O controller . This Low Pin Count (LPC) interface provides the commonly used Super I/O functionality . The chipset supports UART compatible serial ports, one parallel port with EPP and ECP capabilities, a floppy drive, and PS/2 keyboard and mouse.
Chapter 2 Hardware information This chapter describes the hardware setup procedures that you have to perform when installing system components. It includes details on the switch/jumper settings and connector locations on the motherboard.
ASUS PR-DLSW motherboard Chapter summar y 2.1 Motherboard installation ............................... 2-1 2.2 Motherboard layout ....................................... 2-2 2.3 Before you proceed ....................................... 2-3 2.4 Central Processing Unit (CPU) .
ASUS PR-DLSW motherboard user guide 2-1 2. 1 Motherboard ins tallation Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. The PR-DLSW uses the extended A TX form factor that measures 12 in x 13 in (30.
2-2 Chapter 2: Hardware information 2.2 Motherboard layout The SCSI features are optional. These components are grayed out in the above motherboard layout.
ASUS PR-DLSW motherboard user guide 2-3 2.3 Before you proceed T ake note of the following precautions before you install motherboard components or change any motherboard settings. 1. Unplug the power cord from the wall socket before touching any component.
2-4 Chapter 2: Hardware information 2.4 Central Pr ocessing Unit (CPU) 2.4.1 Overview The motherboard comes with dual surface mount 604-pin Zero Insertion Force (ZIF) sockets. The sockets are designed for the Intel Processor in the 603/604-pin package with 512KB L2 cache.
ASUS PR-DLSW motherboard user guide 2-5 Follow these steps to install a CPU. 1. Locate the 604-pin ZIF sockets on the motherboard. Unlock the socket by pressing the lever sideways, then lift it up to at least 1 15° angle. 2. Position the CPU above the socket as shown.
2-6 Chapter 2: Hardware information The Intel ® Xeon ™ processors require specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. Follow these steps to install the CPU heatsink and fan. 2.4.3 Installing the CPU heatsink and fan 1.
ASUS PR-DLSW motherboard user guide 2-7 3. Use a small flat screw driver to attach the other end of the bracket, while firmly holding down the heatsink and fan assembly . The middle hook of the bracket snaps in place if you properly attached the two ends.
2-8 Chapter 2: Hardware information 2.5 System memor y 2.5.1 Overview The motherboard comes with six Double Data Rate (DDR) Dual Inline Memory Module (DIMM) sockets. These sockets support up to 12GB system memory using 184-pin registered PC2100/1600 DIMMs with Serial Presence Detect (SPD) and Error Check and Correction (ECC).
ASUS PR-DLSW motherboard user guide 2-9 2.5.2 Memory Configurations The motherboard supports system memory of up to 12GB in a two-way interleaved configuration. As a rule, this configuration requires that you install identical DDR DIMMs (exactly the same type and size) in pairs.
2-10 Chapter 2: Hardware information 2.5.3 Installing a DIMM Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components. Follow these steps to install a DIMM.
ASUS PR-DLSW motherboard user guide 2-11 2.6 Expansion slots In the future, you may need to install expansion cards. The following sub- sections describe the slots and the expansion cards that they support. 2.6.1 Installing an expansion card Follow these steps to install an expansion card.
2-12 Chapter 2: Hardware information Standard Interrupt Assignments IRQ Priority Standard Function 0 1 System T imer 1 2 Keyboard Controller 2 N/A Programmable Interrupt 3* 1 1 Communications Port (CO.
ASUS PR-DLSW motherboard user guide 2-13 2.6.3 PCI slots This motherboard implements the PCI-X (Peripheral Component Interconnect Extended) bus technology to support up to 133MHz data transfers, or about 1.06GB/s. This bus technology is primarily designed for servers to increase the performance of high bandwidth devices such as Ultra3 SCSI.
2-14 Chapter 2: Hardware information PR-DLSW ® PR-DLSW Accelerated Graphics Port (AGP ) 2.6.4 AGP PRO slot This motherboard has an Accelerated Graphics Port (AGP) PRO slot that supports AGP cards. Note the notches on the card golden fingers to ensure that they fit the AGP slot on your motherboard.
ASUS PR-DLSW motherboard user guide 2-15 2.7 Switches and jumper 2.7.1 Switches The following figure shows the location and default settings of the DIP switches on the motherboard. Keep the default settings for stable system operation. PR-DLSW ® PR-DLSW DIP Switches CONFIG_SW 1.
2-16 Chapter 2: Hardware information SCSI setting (2-pin SCSI_EN) This jumper allows you to enable or disable the onboard SCSI feature. Keep the jumper open if you wish to install SCSI devices. Place a cap on the jumper to disable the onboard SCSI controller .
ASUS PR-DLSW motherboard user guide 2-17 2.8 Connectors This section describes and illustrates the internal connectors on the motherboard. Always connect ribbon cables with the red stripe to Pin 1 on the connectors.
2-18 Chapter 2: Hardware information 3. IDE connectors (40-1 pin IDE1, IDE2) This connector supports the provided UltraDMA/100/66 IDE hard disk ribbon cable.
ASUS PR-DLSW motherboard user guide 2-19 4. Chassis alarm lead (4-1 pin CHASSIS) This lead is for a chassis designed with intrusion detection feature. This requires an external detection mechanism such as a chassis intrusion sensor or microswitch.
2-20 Chapter 2: Hardware information 6. A TX power connectors (24/20-pin EA TXPWR, 8-pin CON12V) These connectors connect to an A TX 12V power supply . The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit.
ASUS PR-DLSW motherboard user guide 2-21 7. CPU, Chassis, and Power Fan Connectors (3-pin CPUF AN1, CPUF AN2, SYSF AN1, SYSF AN2, SYSF AN3) The fan connectors support cooling fans of 350mA~740mA (8.88W max.) or a total of 1A~2.22A (26.64W max.) at +12V .
2-22 Chapter 2: Hardware information 9. T wo 68-pin Ultra160 SCSI Connectors (CHA-WIDE, CHB-WIDE) This motherboard has two 68-Pin Ultra160 SCSI connectors; one for each of the two channels. Each channel can support a maximum of 15 devices as specified by Ultra160 standards.
ASUS PR-DLSW motherboard user guide 2-23 10. W ake-On-LAN Connector (3-pin WOL_CON) This connector supports a LAN card with a W ake-On-LAN output. The connector powers up the system when a wakeup packet or signal is received through the LAN card.
2-24 Chapter 2: Hardware information 13. System panel connector (20-pin P ANEL) This connector accommodates several system front panel functions. PR-DLSW ® PR-DLSW System Panel Connectors PLED MLED P.
ASUS PR-DLSW motherboard user guide 2-25 • System Power LED Lead (3-1 pin PLED) This 3-1 pin connector connects to the system power LED. The LED lights up when you turn on the system power , and blinks when the system is in sleep mode.
2-26 Chapter 2: Hardware information.
Chapter 3 Powering up This chapter describes the power up sequence and gives information on the BIOS beep codes..
ASUS PR-DLSW motherboard Chapter summar y 3.1 Starting up for the first time .......................... 3-1 3.2 Powering off the computer .............
ASUS PR-DLSW motherboard user guide 3-1 3. 1 St ar ting up for t he firs t time 1. After making all the connections, replace the system case cover . 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis.
3-2 Chapter 3: Powering up 3.2 Powering of f the com puter Y ou must first exit the operating system and shut down the system before switching off the power . For A TX power supplies, you can press the A TX power switch after exiting or shutting down the operating system.
Chapter 4 BIOS setup This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
ASUS PR-DLSW motherboard Chapter summar y 4.1 Managing and updating your BIOS .............. 4-1 4.2 BIOS Setup program ...................................... 4-5 4.3 Main Menu ...................................................... 4-8 4.4 Advanced Menu .
ASUS PR-DLSW motherboard user guide 4-1 4.1.1 Creating a bootable disk AFLASH.EXE is a Flash Memory W riter utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM on the motherboard.
4-2 Chapter 4: BIOS Setup 5. Select 1. Save Current BIOS to File from the Main menu and press <Enter>. The Save Current BIOS T o File screen appears.
ASUS PR-DLSW motherboard user guide 4-3 1. Download an updated ASUS BIOS file from the Internet (WWW or FTP) (see ASUS CONT ACT INFORMA TION on page x for details) and save to the boot floppy disk you created earlier . 2. Boot from the floppy disk. 3.
4-4 Chapter 4: BIOS Setup 7. The utility starts to program the new BIOS information into the Flash ROM. The boot block is updated automatically only when necessary . This minimizes the possibility of boot problems in case of update failures. When the programming is done, the message “Flashed Successfully” appears.
ASUS PR-DLSW motherboard user guide 4-5 4.2 BIOS Setup progr am This motherboard supports a programmable Flash ROM that you can update using the provided utility described in section “ 4.
4-6 Chapter 4: BIOS Setup 4.2.1 BIOS menu bar The top of the screen has a menu bar with the following selections: MAIN Use this menu to make changes to the basic system configuration. ADV ANCED Use this menu to enable and make changes to the advanced features.
ASUS PR-DLSW motherboard user guide 4-7 General help In addition to the Item Specific Help window , the BIOS setup program also provides a General Help screen. Y ou may launch this screen from any menu by simply pressing <F1> or the <Alt> + <H> combination.
4-8 Chapter 4: BIOS Setup System Time [XX:XX:XX] Sets the system to the time that you specify (usually the current time). The format is hour , minute, second. V alid values for hour , minute and second are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59).
ASUS PR-DLSW motherboard user guide 4-9 Supervisor Password [Disabled] / User Password [Disabled] These fields allow you to set passwords. T o set a password, highlight the appropriate field and press <Enter>. T ype in a password then press <Enter>.
4-10 Chapter 4: BIOS Setup 4.3.1 Primary and Secondary Master/Slave T ype [Auto] Select [Auto] to automatically detect an IDE hard disk drive. If automatic detection is successful, Setup automatically fills in the correct values for the remaining fields on this sub-menu.
ASUS PR-DLSW motherboard user guide 4-11 If no drive is installed or if you are removing a drive and not replacing it, select [None]. Other options for the T ype field are: [CD-ROM] - for IDE CD-ROM d.
4-12 Chapter 4: BIOS Setup T ranslation Method [LBA] Select the hard disk drive type in this field. When Logical Block Addressing (LBA) is enabled, the 28-bit addressing of the hard drive is used without regard for cylinders, heads, or sectors. Note that LBA Mode is necessary for drives with more than 504MB storage capacity .
ASUS PR-DLSW motherboard user guide 4-13 SMART Monitoring [Disabled] This field allows you to enable or disable the S.M.A.R.T . (Self-Monitoring, Analysis and Reporting T echnology) system that utilizes internal hard disk drive monitoring technology .
4-14 Chapter 4: BIOS Setup 4.3.2 Keyboard Features Boot Up NumLock Status [On] This field enables users to activate the Number Lock function upon system boot. Configuration options: [Off] [On] Keyboard Auto-Repeat Rate [6/Sec] This controls the speed at which the system registers repeated keystrokes.
ASUS PR-DLSW motherboard user guide 4-15 4.4 Advanced Menu CPU Speed [Manual] This field displays the auto-detected CPU speed. CPU Level 1 Cache, CPU Level 2 Cache [Enabled] These fields allow you to choose from the default [Enabled] or choose [Disabled] to turn on or of f the CPU Level 1 and Level 2 built-in cache.
4-16 Chapter 4: BIOS Setup OS/2 Onboard Memory > 64M [Disabled] When using OS/2 operating systems with installed DRAM of greater than 64MB, you need to set this option to [Enabled].
ASUS PR-DLSW motherboard user guide 4-17 4.4.1 Chip Configuration Graphics Aperture Size [64MB] This feature allows you to select the size of mapped memory for AGP graphic data.
4-18 Chapter 4: BIOS Setup 4.4.2 I/O Device Configuration Floppy Disk Access Control [R/W] When set to [Read Only], this parameter protects files from being copied to floppy disks by allowing reads from, but not writes to, the floppy disk drive. The default setting [R/W] allows both reads and writes.
ASUS PR-DLSW motherboard user guide 4-19 Parallel Port Mode [ECP+EPP] This field allows you to set the operation mode of the parallel port. [Normal] allows normal-speed operation but in one direction .
4-20 Chapter 4: BIOS Setup 4.4.3 PCI Configuration Slot 1, Slot 2, Slot 3, Slot 4, Slot 5, Slot 6 IRQ [Auto] These fields set how IRQ use is determined for each PCI slot. The default setting for each field is [Auto], which utilizes auto-routing to determine IRQ use.
ASUS PR-DLSW motherboard user guide 4-21 Onboard SCSI BIOS [Auto] [Auto] allows the motherboard BIOS to detect whether you have a Adaptec SCSI controller . If the SCSI controller is detected, the SCSI BIOS will be enabled. If no SCSI controller is detected, the onboard SCSI BIOS will be disabled.
4-22 Chapter 4: BIOS Setup 4.5 Power Menu The Power menu allows you to reduce power consumption. This feature turns of f the video display and shuts down the hard disk after a period of inactivity . Power Management [User Defined] This field allows you to activate or deactivate the automatic power saving features.
ASUS PR-DLSW motherboard user guide 4-23 V ideo Off Option [Suspend -> Off ] This field determines when to activate the video off feature for monitor power management. Configuration options: [Always On] [Suspend -> Off] V ideo Off Method [DPMS OFF] This field defines the video of f features.
4-24 Chapter 4: BIOS Setup 4.5.1 Power Up Control AC PWR Loss Restart [Disabled] This allows you to set whether or not to reboot the system after power interruptions. [Disabled] leaves your system off. [Previous State] sets the system back to the state it was before the power interruption.
ASUS PR-DLSW motherboard user guide 4-25 Power On By PS/2 Keyboard [Disabled] This parameter allows you to use specific keys on the keyboard to turn on the system. This feature requires an A TX power supply that provides at least 1A on the +5VSB lead.
4-26 Chapter 4: BIOS Setup 4.5.2 Hardware Monitor MB Temperature [xxxC/xxxF] CPU1 Temperature [xxxC/xxxF] CPU2 Temperature [xxxC/xxxF] The onboard hardware monitor is able to detect the MB (motherboard) and CPU temperatures. Set to [Ignore] only if necessary .
ASUS PR-DLSW motherboard user guide 4-27 4.6 Boot Menu The motherboard BIOS supports the BIOS Boot Specification (BBS) version 1.01. BBS is an intelligent mechanism that provides flexible ways to set boot sequence for Initial Program Load (IPL) devices such as CD-ROMs, network remote boot ROM, and SCSI or RAID controllers on PnP cards.
4-28 Chapter 4: BIOS Setup 3rd Boot : (BEV) [<0> Intel Corporation] This field allows you to select a Bootstrap Entry V ector (BCV) device to boot from. BEV devices include network controllers or cards. The BEV devices present in the system will appear as options for this field.
ASUS PR-DLSW motherboard user guide 4-29 DRAM Hot Spare [Disabled] This field allows you to allocate rows of SDRAM for hot spare. Configuration options: [Disabled] [1 row] [2 rows] [3 rows] Remote Console [Disabled] This field allows the text mode VGA display to be sent out to VT100 terminal through COM1.
4-30 Chapter 4: BIOS Setup 4.8 Exit Menu When you have made all of your selections from the various menus in the Setup program, save your changes and exit Setup.
ASUS PR-DLSW motherboard user guide 4-31 Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press <F5>, a confirmation window appears. Select [Y es] to load default values.
4-32 Chapter 4: BIOS Setup.
Chapter 5 OS Installation This chapter tells how to install SCSI, LAN, and audio drivers for various operating systems..
ASUS PR-DLSW motherboard Chapter summar y 5.1 Microsoft Windows NT Server 4.0 ................ 5-1 5.2 Microsoft Windows 2000 Server ................... 5-9 5.3 Microsoft Windows XP Professional .......... 5-18 5.4 Novell NetW are Server .............
ASUS PR-DLSW motherboard user guide 5-1 5. 1 Micr osof t ® W indows ® NT Ser ver 4.0 5.1.1 LSI ® SCSI Driver Installation Windows NT 4.0 do not have drivers for the new SCSI controllers, you must load the driver manually prior to Windows NT 4.0 installation.
5-2 Chapter 5: OS Installation 3. When prompted for the manufacturer-supplied hardware support disk, insert the appropriate LSI driver disk containing the Windows NT driver required to support your LSI adapter(s) and press Enter .
ASUS PR-DLSW motherboard user guide 5-3 9. Depending on the driver being installed, Symbios Ultra3 PCI SCSI Driver is shown highlighted. Press Enter to proceed. 10. The Windows NT Workstation Setup window reappears. If using an IDE CD-ROM Drive for installation, press S to load additional drives.
5-4 Chapter 5: OS Installation 9. For the path to the OEM SCSI Adapter files, A:WINNTMINIPORT should be displayed. Select Continue. Then remove the floppy disk from your A: drive. 10. The System Settings Change message displays: “Y ou must restart your computer before the new settings take effect.
ASUS PR-DLSW motherboard user guide 5-5 B. New System Installation 1. When the Installing Windows NT Networking screen appears, press Next to display the following screen. 2. Check the Wired to the Network box, then click Next . 3. On the screen that appears, click the button Select from list.
5-6 Chapter 5: OS Installation 8. Click Select from list... , then click Have Disk... 9. T ype A: in the dialog box, then click OK. 10. In the following screen, select Intel(R) PRO/1000 Family Adapter , then click OK. Follow the succeeding screen instructions.
ASUS PR-DLSW motherboard user guide 5-7 C. Existing System Installation 1. Double-click the Network icon in the Control Panel. 2. Select the Adapter tab, then click Add . A list of adapters appears. 4. Do not select an adapter from the list. Instead, insert the LAN driver disk that you created from the PR-DLSW support CD.
5-8 Chapter 5: OS Installation 5.1.3 C-Media Audio Device Driver Installation It is recommended that you install Windows NT 4.0 before installing the device driver for the C-Media CMI8738/PCI-SX audio controller . Do not install any other audio device drivers if you install the C-Media driver .
ASUS PR-DLSW motherboard user guide 5-9 5.2 Microsof t ® Windows ® 2000 Ser ver 5.2.1 LSI ® SCSI Driver Installation A. Preparing an LSI Driver Disk The drivers are located on ASUS Driver Support CD at: DriversSdmsDriversW in2k Copy all the files and subdirectory under the Win2k subdirectory to the root directory of a clean floppy disk.
5-10 Chapter 5: OS Installation 4. The appropriate driver is shown highlighted. Press Enter to proceed. 5. Return to the Windows 2000 Setup screen. Press Enter to proceed. The message about setup loading files appears. At this point, simply follow the Microsoft Windows 2000 installation procedure.
ASUS PR-DLSW motherboard user guide 5-11 Drivers are digitally signed by the Microsoft Windows Hardware Quality Lab (WHQL). Due to the delay between the general customer release by LSI Logic of Windows drivers and the completion of WHQL testing, some drivers that are distributed with adapters or downloaded from the LSI Logic web site at www .
5-12 Chapter 5: OS Installation 5.2.2 Intel ® 82551QM LAN Driver Installation Y ou may install the Intel 82551QM LAN drivers directly from the PR-DLSW support CD. Proceed to the section “B. Update LAN Driver on an Existing System Installation.” If you wish to create a LAN driver disk, proceed to the section “A.
ASUS PR-DLSW motherboard user guide 5-13 When done, your Computer Management window shows the installed LAN adapters. 4. Highlight the Intel(R) PRO-100 S Server Adapter , click the right mouse button, and select Properties to display the following.
5-14 Chapter 5: OS Installation Y ou may also update the LAN drivers from the LAN Driver Disk if you created one. Follow these steps to update from the LAN driver disk. 1. Boot Windows 2000 system and log on as Administrator . 2. Click on the Start button.
ASUS PR-DLSW motherboard user guide 5-15 5.2.3 C-Media Audio Device Driver Installation T o install the device drivers for the C-Media CMI8738/PCI-SX audio controller under Windows 2000: 1. Insert the PR-DLSW support CD into your CD-ROM drive. When Autorun in enabled in your computer , the Drivers menu automatically appears.
5-16 Chapter 5: OS Installation 6. When prompted for the destination folder to install the driver and applications, select the recommended default by clicking Next.
ASUS PR-DLSW motherboard user guide 5-17 5.2.4 Enabling A T A100 Feature in Windows ® 2000 T o enable the A T A100 feature under Windows 2000, you need to upgrade to Windows 2000 Service Pack 2 or 3. 5.2.5 Enabling AGP Bridge Driver in Windows ® 2000 T o enable the AGP bridge driver under Windows 2000: 1.
5-18 Chapter 5: OS Installation 5.3 Microsof t ® W indows ® XP Professional 5.3.1 LSI SCSI Driver and Intel 82551QM LAN Driver installation Windows XP contains default drivers to support the Intel 82551QM chipset and the LSI 53C1010R SCSI controller .
ASUS PR-DLSW motherboard user guide 5-19 5. Follow the succeeding installation instructions. 6. When done, the following screen appears. Click Finish to complete the installation.
5-20 Chapter 5: OS Installation C. NetW are 5.X New Installations Visit the Novell website (www .novell.com) for information on Netware 5.X support. 5.4 Novell ® NetWare ® Ser ver 5.4.1 LSI ® SCSI Driver Installation A single driver (*HAM) is provided for the Novell NetW are 4.
ASUS PR-DLSW motherboard user guide 5-21 D. NetW are 4.XX New Installations 1. Begin the file server installation according to the instructions in the file server installation chapter in the Novell NetW are Installation Manual.
5-22 Chapter 5: OS Installation 5.4.2 Intel ® 82551QM LAN Driver Installation A. Preparing Intel 82551QM LAN Driver Disk 1. Use the self-extracting image files. For the Intel(R) PRO/100 Server Adapter driver , the executable file is located here: DriversLanmakediskmakenw .
ASUS PR-DLSW motherboard user guide 5-23 B. NetW are 4.XX, 5.X, and 6.X Installations 1. Prepare the Intel(R) PRO/100 Server Adapter driver from the previous section.
5-24 Chapter 5: OS Installation 5.5 SUN Solaris 7 Ser ver 5.5.1 LSI ® SCSI Driver Installation A. Building the SYMHISL Driver Update Disk 1. Use the self-extracting image files For the LSI_U3.SYS driver , the executable file is located here: DriversSdmsDiskimagSolaris7.
ASUS PR-DLSW motherboard user guide 5-25 For DOS System Users: Under this section, you have two choices. 1. Use a utility that will copy the raw dd image onto a 1.44MB floppy disk. This dd image is located at: DriversSdmsDriversUNIXESSOLARISSolaris7SYMITU.
5-26 Chapter 5: OS Installation 5. Select the appropriate Solaris operating system, and press F2_Continue . The Loading Driver Update Software screen appears, along with a progress bar that shows the percentage of drivers that have been extracted from the diskette.
ASUS PR-DLSW motherboard user guide 5-27 14. Press F2_Continue . Drivers for the device controller that you selected are displayed. Y our system boots to run the install program. The install program starts and your machine begins booting the complete Solaris operating environment.
5-28 Chapter 5: OS Installation C. Existing System Installation Before adding new or updated drivers, the newly supported hardware devices should be installed and configured according to the instructions in the corresponding Device Reference Page, if any .
ASUS PR-DLSW motherboard user guide 5-29 7. If the driver is the one that you want to install, type Y for yes or press Enter . If the driver is not the one you want to install, type N for no. If you specify yes, the install.sh script installs the driver you indicated as well as bootmod and bootbin patches.
5-30 Chapter 5: OS Installation 5.6 SCO Open Ser ver 5.0.x 5.6.1 LSI ® SCSI Driver Installation A. Building the SCO OpenServer BTLD Diskette T o create a BTLD diskette for SCO OpenServer system, copy the raw dd image file onto a 1.44MB floppy disk. This process is dependent upon the operating system that you are using to create this diskette.
ASUS PR-DLSW motherboard user guide 5-31 B. New System Installation This procedure installs SCO UNIX onto a hard disk drive. This installation is necessary to build a new UNIX kernel that includes your SDMS driver . During installation, you are given the option of retaining current partitions on the root hard disk.
5-32 Chapter 5: OS Installation C. Existing System Installation This procedure assumes SCO UNIX is already installed on a hard disk drive. This installation is necessary to build a new UNIX kernel that includes the proper LSI host adapter driver . The basic steps for accomplishing this are outlined below .
ASUS PR-DLSW motherboard user guide 5-33 b. “Do you want the kernel envir onment rebuilt (y/n)?” T ype: y Press Enter . 9. T o activate the new kernel, you must reboot the system. At the command prompt, type: # r eboot (or init 6) 5.6.2 Intel ® 82551QM LAN Driver Installation SCO OpenServer 5.
5-34 Chapter 5: OS Installation 5.7 SCO UnixWare Ser ver 5.7.1 LSI ® SCSI Driver Installation A. Building the SCO UnixW are C8XX BTLD Diskette T o create a C8XX BTLD diskette to use with UnixW are 2.1.X or UnixW are 7, copy the raw dd image file onto a 1.
ASUS PR-DLSW motherboard user guide 5-35 For DOS System Users: Under this section, you have two choices. 1. Use a utility that will copy the raw dd image onto a 1.44MB floppy disk. For UnixW are 2.1.X, this dd image is located at: DriversSdmsDriversUNIXESUNIXW AREUW21XUNIXW ARE.
5-36 Chapter 5: OS Installation C. Existing System Installation Adding or Updating the C8XX Package for LSI SCSI controller . Before you install the C8XX driver , make a backup copy of the existing kernel: 1. Log on as root . 2. At the shell prompt, type: # cp /stand/unix /stand/unix.
ASUS PR-DLSW motherboard user guide 5-37 5.7.2 Intel ® 82551QM LAN Driver Installation SCO UnixW are 7.1.1 system can correctly recognize Intel 82551 network controller during installation. User doesn’t need to load or modify the network driver for the onboard LAN device.
5-38 Chapter 5: OS Installation 5.8 Linux RedHat 7 .x 5.8.1 LSI SCSI Driver Installation The LSI 53C1010R controller , you need to load the LSI driver (RedHat 7.0) for support the LSI 53C1010R/53C1030 controller . The RedHat 7.1 or later version already bundle with LSI 53C1010R/53C1030 driver support.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Asus PR-DLSW c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Asus PR-DLSW - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Asus PR-DLSW, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Asus PR-DLSW va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Asus PR-DLSW, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Asus PR-DLSW.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Asus PR-DLSW. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Asus PR-DLSW ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
