Manuel d'utilisation / d'entretien du produit EN2218 du fabricant Accton Technology
Aller à la page of 62
Multi-Function Ethernet + Modem/Fax PC Card User’s Guide.
Multi-Function Ethernet + Modem/Fax PC Card User’s Guide.
Accton Technology Corporation makes no representations or warranties with respect to the contents or use of this manual, any driver or testing software; and specifically disclaims any expressed or implied warranties of merchantability or fitness for any particular purpose.
About this Manual i About this Manual This is an installation guide for Accton’s Ethernet+Modem/Fax PC Card. This manual covers the following topics: • Product description, summary of features and.
Ethernet+Modem/Fax PC Card User’s Guide About this Manual ii Back up your driver diskettes and use the copy as the working diskette. Do this to protect the original from accidental damage. @ Fill in the Owner Registration Card and mail it to Accton Technology Corporation.
Quick Installation Guide iii Quick Installation Guide 1Step is designed to simplify the process of configuring the PC Card to run with NetWare or other network operating systems. To quickly install and configure your card, do the following: 1. Install the PC Card into a Type II PCMCIA slot.
.
Contents v Contents Chapter 1 Introduction 1-1 Features 1-1 Chapter 2 Installation 2-1 Pre-Installation Considerations 2-1 Installing the Hardware 2-1 PC Card Installation 2-1 Connecting the Adapter C.
Ethernet+Modem/Fax PC Card User’s Guide Contents vi Selecting the Frame Type 3-6 Selecting Memory Management Options 3-7 Identifying the Driver’s Directory Location 3-7 Installing the Software Dri.
Ethernet+Modem/Fax PC Card User’s Guide Contents vii Appendix E Product Support Services E-1 Product Registration E-1 Problem Report E-1 Hardware Repair Service E-1 Software Update and Upgrade Service E-2 Bulletin Board Service (BBS) E-2 Interactive Fast Fax (U.
Introdution 1- 1 Chapter 1 Introduction The Ethernet/Modem PC Card is a recent development in PCMCIA card technology. This card can manage the PC Ethernet interface and Data/Fax/ Modem connections simultaneously.
Installation 2- 1 Chapter 2 Installation This chapter describes your PC Card and shows you how to install it. To install the Fax Utility, see instructions that come with the software. Pre-Installation Considerations When preparing to install your PC Card, make sure you have the required hardware and software in place.
Ethernet+Modem/Fax PC Card User’s Guide 2-2 Installation Connecting the Adapter Cable to the PC Card 1. Plug the wide connector on the end of the Y-cable to the mating connector on the PC Card. Make sure the side of the Y-cable connector with the arrow heads faces upwards.
Ethernet+Modem/Fax PC Card User’s Guide Installation 2- 3 Installing the Software Running Card Diagnostics When hardware installation is complete, run diagnostics to check the card and the network cabling with the 1Step program. 1Step is in the root directory of the driver diskette that comes with the package.
Ethernet+Modem/Fax PC Card User’s Guide 2-4 Installation Software Installation Advisory 1. For those who intend to install Card and Socket Service Support drivers, reserve at least 64 KB of memory to provide enough resources for other PC Cards. Example: DEVICE=EMM386.
Ethernet+Modem/Fax PC Card User’s Guide Installation 2- 5 Using Card and Socket Services Support You can use third-party Card Services Super Client drivers to activate your PC Card. They are available from several vendors like SystemSoft, Phoenix, AMI, DataBook and Award, just to name a few.
Ethernet+Modem/Fax PC Card User’s Guide 2-6 Installation 2. Invoke the 1Step installation program and choose Install Software from the Action Menu to copy the Client Drivers for Novell into your PC. (Refer to Using 1Step in Chapter 3 for more details.
Ethernet+Modem/Fax PC Card User’s Guide Installation 2- 7 5. Test the PC Card’s Modem function by dialing out over the modem. (Refer to Chapter 4 for Modem Setup ). Installing under Window s for Workgroups (W FW 3.11) 1. Remove the existing PC Card and replace it with your EN2218 PC Card.
Ethernet+Modem/Fax PC Card User’s Guide 2-8 Installation 13. Reboot your PC. During bootup, the LAN/modem I/O addresses, modem Port and IRQ will be displayed.
Ethernet+Modem/Fax PC Card User’s Guide Installation 2- 9 Installing under Window s 95 The installation process under Win95 is fairly simple. Follow the procedures listed below to complete installation. 1. If you already have a PC Card installed, you need to remove its components by doing the following, otherwise go to step 2.
Ethernet+Modem/Fax PC Card User’s Guide 2-10 Installation 6. Verify the LAN function by using Network Neighborhood to browse the network for any existing server. Note: NetWare Network support is loaded by default when the PC Card is installed. 7. Verify the Modem function by opening up the Dial-Up Networking folder and connecting to a modem site.
Ethernet+Modem/Fax PC Card User’s Guide Installation 2- 11 Connecting to a NetWare network is easy under Windows NT. To install NetWare network support: 1. Go to the Control Panel and double-click on the Network icon. 2. Click on Add Software... to display the N etwork Software list.
Using 1Step 3- 1 Chapter 3 Using 1Step TM 1Step is designed to simplify hardware diagnostics and software installation. Note that any changes made to the card’s hardware configuration are only made available for diagnostic tests performed under 1Step.
Ethernet+Modem/Fax PC Card User’s Guide 3-2 Using 1Step Overview of 1Step 1. Type the following command at the DOS prompt, then press <Enter> to display the main screen for 1Step: 1STEP <Enter> 2. Select the appropriate hardware settings for Card diagnostics.
Ethernet+Modem/Fax PC Card User’s Guide Using 1Step 3- 3 Setting the Hardw are Configuration Select the appropriate I/O base address and interrupt for diagnostics.
Ethernet+Modem/Fax PC Card User’s Guide 3-4 Using 1Step Running Diagnostics Select the Test Adapter command from the Action Menu to run diagnostics. Running diagnostics on a single PC lets you monitor the adapter and the corresponding cabling system.
Ethernet+Modem/Fax PC Card User’s Guide Using 1Step 3- 5 Available Diagnostic Tests You need not start any network operating system to run the following tests: • Configuration Test - Identifies th.
Ethernet+Modem/Fax PC Card User’s Guide 3-6 Using 1Step Press <F1> to activate on-line help and select the driver you need. The corresponding README.TXT file containing driver installation instructions will be displayed. The following are the Network Operating Systems supported by Accton’s 1Step: NetWare Workstation version 4.
Ethernet+Modem/Fax PC Card User’s Guide Using 1Step 3- 7 Selecting Memory Management Options The host PC may be using Memory Management software. There are four selections available, namely, Normal , Use XMSNETx , Use EMSNETx , and DOS5+LOADHIGH . The default setting is Normal .
Ethernet+Modem/Fax PC Card User’s Guide 3-8 Using 1Step Table 3.1 File Menu Commands File Menu Commands Action DOS Shell Opens a DOS shell within 1Step Exit Exits 1Step and returns to DOS The *.1st file contains the card’s software configuration for the network environment.
Modem/Fax Setup 4- 1 Chapter 4 Modem/Fax Setup When plugging your PC card into a phone line, make sure you use an analog line. Lines used by standard household telephones, Fax machines or other modems are analog phone lines. Do not use a digital line.
Ethernet+Modem/Fax PC Card User’s Guide 4-2 Modem/Fax Setup • Selecting a Mode (Modem Choice) To determine your modem’s model, check the modem equipment itself, and the documentation that comes with it.
Ethernet+Modem/Fax PC Card User’s Guide Modem/Fax Setup 4- 3 • Error Correction Accton’s Modem PC card utilizes the highly reliable Microcom Network Protocol (MNP) and V.42 correction method. These are industry standards which ensure an accurate modem connection and more stringent data security.
Fax Operations 5- 1 Chapter 5 Fax Operations This chapter describes some of the more common features of Fax software (each of which applies to the Delrina 4-in-1 Fax software). Unless you plan on using the Windows 95 Fax Utility, Fax software needs to be installed before you can transmit or receive a fax.
Troubleshooting A- 1 Appendix A Troubleshooting Ethernet Network Interface 1Step includes a diagnostics program for checking the card’s components and network cabling.
Ethernet+Modem/Fax PC Card User’s Guide A-2 Troubleshooting Symptoms 1. Twisted-pair connection results in card failure. 2. Running Test Adapter results to External Loopback Test failure. Possible Cause Invalid twisted-pair link Suggestions 1. Check the RJ-45 connection for loose cabling.
Ethernet+Modem/Fax PC Card User’s Guide Troubleshooting A- 3 Symptom Cannot run mouse while running 1Step. Possible Cause IRQ conflict Suggestions 1. Change the IRQ setting of the Card. 2. Run mouse driver. Symptom Card failure after configuration. Possible Cause 1.
Ethernet+Modem/Fax PC Card User’s Guide A-4 Troubleshooting Modem This section lists some of more common symptoms encountered and possible solutions during modem and software setup.
Ethernet+Modem/Fax PC Card User’s Guide Troubleshooting A- 5 Table A.1 Common Modem Problems and Possible Solutions(cont.) Symptoms Possible Solutions Modem won’t connect − Make sure the parity,.
Modem ATCommands and S-Registers B- 1 Appendix B Modem AT Commands and S-Registers The AT command set allows you to control your modem from a command line or from terminal mode. Some guidelines for using the AT command set are listed in the following tables.
Ethernet+Modem/Fax PC Card User’s Guide B-2 Modem AT Commands and S-Registers Table B.1 AT Command Summary Command Description Usage Default ATF0 Auto-detect mode Select auto-detect mode (equivalent to N1) Y ATH Initiate Hangup Sequence Break up connection between two modems.
Ethernet+Modem/Fax PC Card User’s Guide Modem AT Commands and S-Registers B- 3 Table B.1 AT Command Summary (cont.) Command Description Usage Default ATX0 Basic call progress result codes report Report basic call progress result codes, i.
Ethernet+Modem/Fax PC Card User’s Guide B-4 Modem AT Commands and S-Registers Table B.1 AT Command Summary (cont.) Command Description Usage Default AT&C0 Force RLSD active Force RLSD active reg.
Ethernet+Modem/Fax PC Card User’s Guide Modem AT Commands and S-Registers B- 5 Table B.1 AT Command Summary (cont.) Command Description Usage Default AT&W Write to Stored Profile 0 Write a command to the modem’s memory (stored profile 0).
Ethernet+Modem/Fax PC Card User’s Guide B-6 Modem AT Commands and S-Registers S-registers are 8-bit status registers where modems store most of their configuration information. You can use the AT commands to modify the features of the modem’s operation by writing directly into these registers.
Specifications C-1 Appendix C Specifications System Configuration Ethernet Standards Conformance : IEEE 802.3 Standard, PCMCIA Release 2.1 Type II, JEIDA 4.
Ethernet+Modem/Fax PC Card User’s Guide C-2 Specifications Modem Standards Conformance Data : V.34, V.32bis, V.32, V.22bis, V.22A/B, V.23, V.21, Bell 212 A/B, Bell 103 Fax : V.17, V.29, V.27ter, V.21 channel 2, G3 Error Correction : V.42, MNP Data Compression : V.
Regulatory Standards Conformance D-1 Appendix D Regulatory Standards Conformance EMI Warning FCC Part 15 Class B Certification Accton Technology Corporation Model Numbers: EN2218 FCC ID: HEDEN2218 This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1.
Ethernet+Fax/Modem PC Card User’s Guide D-2 Regulatory Standards Conformance You are hereby cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
Ethernet+Fax/Modem PC Card User’s Guide Regulatory Standards Conformance D- 3 The REN is used to determine the quantity of devices that may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call.
Product Support Services E- 1 Appendix E Product Support Services Product Registration Fill in the Owner Registration Card and mail it to Accton Technology Corporation. Accton will keep your record and inform you of any new Accton product developments.
Ethernet+Modem/Fax PC Card User’s Guide E-2 Product Support Services Software Update and Upgrade Service Accton constantly improves its software products by adding enhancements and new features.
Ethernet+Modem/Fax PC Card User’s Guide Product Support Services E- 3 • To obtain software upgrades connect via ftp to ftp.accton.com.tw • Send your technical questions by email to support@accton.com.tw • Mail your technical questions to: For all countries except North America Accton Technology Corporation Attn: Technical Support No.
Ethernet+Modem/Fax PC Card User’s Guide E-4 Product Support Services Limited Five Year Warranty Limited Warranty Accton warrants to the original owner that the product delivered in this package will.
Ethernet+Modem/Fax PC Card User’s Guide Product Support Services E- 5 Return Process Before you may return any Accton product to Accton, you must request an RMA number by calling, Faxing or writing Accton’s Service Department at the number provided by Accton.
Ethernet+Modem/Fax PC Card User’s Guide E-6 Product Support Services Accton Offices Accton Technology Corporation International Headquarters No. 1 Creation Rd.
Glossary 1 Glossary 10BASE-T IEEE’s specifications for 10 Mbps Ethernet using twisted-pair cable (100 W STP or UTP). The m axim um length of c able f or a point-to-point connection is 100 m eters. 1Step Specialized program used with Accton's Ethernet Adapters for quick adapter software installation and diagnostics.
Ethernet+Modem/Fax PC Card User’s Guide 2 Glossary Loopback Diagnostic test in which a signal is transmitted across a medium while sending device waits for its return. Modem Device that performs modulation and demodulation, allowing data communications to occur in analog form over telephone circuit.
Index 1 Index Symbols 1Step 1-1 , 2-3 , 3-1 , A-1 Overview 3-2 Screen 3-1 Using 3-1 68-pin PC Card connector 2-1 A ACC2218.EXE 2-8 Action Menu A-1 Opening 3-8 B bps 4-1 Bulletin Board Service (BBS) E-.
Ethernet+Modem/Fax PC Card User’s Guide 2 Index Drivers C-1 Interactive Fast Fax E-2 Interrupt C-1 Selecting 3-3 Introduction 1-1 IRQ 2-7 L Limited Five Year Warranty E-4 Limited Warranty E-4 M Memo.
Ethernet+Modem/Fax PC Card User’s Guide Index 3 X XON/XOFF 4-2 Y Y-cable 2-2.
EN2218 E1196-R03 150640-101.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Accton Technology EN2218 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Accton Technology EN2218 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Accton Technology EN2218, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Accton Technology EN2218 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Accton Technology EN2218, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Accton Technology EN2218.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Accton Technology EN2218. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Accton Technology EN2218 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
