Manuel d'utilisation / d'entretien du produit SKM-540S du fabricant Onkyo
Aller à la page of 80
E n 7.1ch Home Theater System HT -S790 AV Receiv er (HT -R540) Front Speak ers (SKF-540F) Center Speaker (SKC-540C) Surround Speak ers (SKM-540S) Surround Back Speak ers (SKB-540) Po wered Subwoofer (SKW -540) Instruction Manual Thank you for purchasing an Onkyo 7.
2 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follo w all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any v entilation openings.
3 Precautions 1. Recording Copyright —Unless it’ s for personal use only , recording copyrighted material is illegal with- out the permission of the copyright holder . 2. A C Fuse —The A C fuse inside the unit is not user- serviceable. If you cannot turn on the unit, contact your Onkyo dealer .
4 Speaker Precautions Placement • The speaker cabinets are made out of wood and are therefore sensitiv e to extreme temperatures and humidity , do not put them in locations subject to direct sunlight or in humid places, such as near an air condi- tioner , humidifier, bathroom, or kitchen.
5 Enjo ying Home Theater Y ou can use two sets of speakers with the A V receiv er: speak er set A and speak er set B . Speaker set A (included speakers) should be used in your main listening room for up to 7.1-channel playback. *While speaker set B is on, speaker set A is reduced to 5.
6 Pa ck ag e Contents Make sure you ha ve the follo wing items: * In catalogs and on packaging, the letter at the end of the product name indicates the color .
7 Features Amplifier • 7-channel amplifier • 110 watts per channel rms into 8 ohms, 2 channels driv en at 1 kHz, less than 0.9% total harmonic distor- tion (FTC rating) • WRA T (Wide Range Amp.
8 Connect the A V receiver to y our A V system. ☞ page 19 COA XIAL REMOTE CONTROL OPTICAL 1 Y P B P R 2 3 DIGITAL IN L R L R L L L R R L R R V S CD TAPE XM ANTENNA FM AM 75 COMPONENT VIDEO 2 IN IN I.
9 Contents Introduction Important Safety Instructions ....................2 Precautions ................................................. 3 Speaker Precautions ..................................4 Enjoying Home Theater ..............................5 Speaker Sets A and B .
10 Getting to Kno w the A V Receiver For detailed information, see the pages in parentheses. A ST ANDBY/ON button (34) Sets the A V receiv er to On or Standby . B ST ANDBY indicator (34) Lights up when the A V receiv er is on Standby and flashes while a signal is being receiv ed from the remote controller .
11 Getting to Know the A V Receiver —Continued J T ONE, [–], and [+] buttons (44) Used to adjust the bass and treble. K STEREO button (46) Selects the Stereo listening mode. L LISTENING MODE [ ]/[ ] buttons (46) Select the listening modes. M DISPLA Y button (37) Displays various information about the currently selected input source.
12 Getting to Know the A V Receiver —Continued A DIGIT AL IN OPTICAL 1, 2, 3, and CO AXIAL These optical and coaxial digital audio inputs are for connecting components with optical or coaxial digital audio outputs, such as CD and D VD players.
13 Remote Contr oller Notes: • If the remote controller doesn’t w ork reliably , try replacing the batteries. • Don’t mix ne w and old batteries or different types of batteries. • If you intend not to use the remote controller for a long time, remov e the batteries to prev ent damage from leakage or corrosion.
14 Remote Controller —Continued Including the A V receiv er, the remote controller can be used to control up to sev en different components. The remote controller has a specific operating mode for use with each type of component. Modes are selected by using the six REMO TE MODE buttons.
15 Remote Controller —Continued For detailed information, see the pages in parentheses. A ON/ST ANDBY button (34) Sets the A V receiv er to On or Standby . B INPUT SELECT OR buttons (36) Used to select the input sources. C MUL TI CH button (37) Selects the multichannel D VD input.
16 Remote Controller —Continued By default, the remote controller is set to control an Onkyo D VD player . A ON/ST ANDBY button Sets the D VD player to On or Standby . B Number buttons Used to enter title, chapter , and track numbers and times for locating specific points.
17 Remote Controller —Continued By default, the remote controller is set to control an Onkyo CD player . A ON/ST ANDBY button Sets the component to On or Standby . B Number buttons Used to enter track numbers and times for locating specific points on CD/MD players.
18 Speaker s For detailed information, see the pages in parentheses. A ST ANDBY/ON indicator Red: Subwoofer in standby mode Green: Subwoofer on W ith the Auto Standby function, the SKW -540 automatically turns on when an input signal is detected in Standby mode.
19 Connecting Y our Speakers Read the following before connecting your speak ers: •Y ou can connect speakers with an impedance of 8 ohms or higher . If you use speakers with a lo wer impedance, and use the amplifier at high volume le v- els for a long period of time, the built-in protection circuit may be activ ated.
20 Connecting Antennas This section explains ho w to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially av ailable outdoor FM and AM antennas. The A V receiv er won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner .
21 Connecting Antennas —Continued If you cannot achiev e good reception with the supplied indoor FM antenna, try a commercially av ailable out- door FM antenna instead. Notes: • Outdoor FM antennas work best outside, b ut usable results can sometimes be obtained when installed in an attic or loft.
22 Connecting Y our Components • Before making any A V connections, read the manuals supplied with your other A V components. • Don’t connect the po wer cord until you’ ve completed and double-checked all A V connections.
23 Connecting Y our Components —Continued By connecting both the audio and video outputs of your D VD player and other A V components to the A V receiver, you can switch the audio and video signals simultaneously simply by changing the input source on the A V receiv er.
24 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from your TV and listen via speaker set B. •T o enjoy Dolby Digital and DTS, use connection or .
25 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from a D VD and listen via speaker set B. •T o enjoy Dolby Digital and DTS, use connection or .
26 Connecting Y our Components —Continued Hooking Up the Multichannel D VD Input If your D VD player supports multichannel audio formats such as DVD-Audio or SA CD, and it has a multichannel analog audio output, you can connect it to the A V receiv er’ s multichannel DVD input.
27 Connecting Y our Components —Continued W ith this hookup, you can use your VCR’ s tuner to listen to your fav orite TV programs via the A V receiv er, useful if your TV has no audio outputs. •W ith connection , you can listen to the VCR or DVD recorder e ven via speaker set B.
28 Connecting Y our Components —Continued Connecting a VCR or D VD Recorder f or Recording Connection A V receiver Signal flow VCR or D VD recorder Picture quality VIDEO 1 OUT S ⇒ S-Video input B.
29 Connecting Y our Components —Continued W ith this hookup, you can use your satellite or cable receiver to listen to your f av orite TV programs via the A V receiv er, useful if your TV has no audio outputs. •W ith connection , you can listen to and record audio from the video source and listen via speak er set B.
30 Connecting Y our Components —Continued ■ CD Play er or T urntable (MM) with Built-in Phono Preamp •W ith connection , you can listen to and record audio from your CD player or turntable and listen via speak er set B. •T o connect the CD player digitally , use connection or .
31 Connecting Y our Components —Continued As of this printing, the Onkyo Remote Interacti ve Dock is the only HDD-compatible component av ailable. ■ For HDD-compatible components that support vide.
32 Connecting Y our Components —Continued •W ith connection , you can listen via speak er set B. •T o connect the recorder digitally , use connections and , or and . The A V receiv er has an AC outlet on its rear panel for connecting the power cord of another A V component.
33 Connecting Y our Components —Continued W ith (Remote Interactive), you can use the follo wing special functions: ■ A uto P ower On/Standby When you start playback on a component connected via , if the A V receiv er is on Standby , it will automatically turn on and select that component as the input source.
34 T urning On the A V Receiver MASTER VOLUME VIDEO STANDBY TONE DISPLAY STEREO DIMMER MEMORY DIGITAL INPUT TUNING MODE AB SPEAKERS TUNER TAPE VIDEO 3 VIDEO 2 VIDEO 1 VCR DVD MULTI CH C D SETUP RETURN.
35 Fir st Time Setup To enjoy Dolby Digital and DTS, you must connect your D VD player to the A V receiver digitally (coaxial or opti- cal). Here are the default assignments.
36 Pla ying Y our A V Components Basic A V Receiver Operation MASTER VOLUME VIDEO STANDBY TONE DISPLAY STEREO DIMMER MEMORY DIGITAL INPUT TUNING MODE AB SPEAKERS TUNER TAPE VIDEO 3 VIDEO 2 VIDEO 1 VCR.
37 Playing Y our A V Components —Continued The multichannel D VD input is for connecting a compo- nent with a 7.1-channel analog audio output, such as a D VD-Audio or SACD-capable D VD player , or an MPEG decoder . See page 26 for hookup information.
38 Listening to the Radio W ith the built-in tuner , you can enjoy AM and FM radio stations. ■ AM Frequency Step Setup (not North America) Y ou must specify the AM frequency step used in your area. Note that when this setting is changed, all radio presets are deleted.
39 Listening to the Radio —Continued ■ T uning into Stations by Frequenc y Y ou can tune into AM and FM stations directly by enter- ing the appropriate frequency . Y ou can store a combination of up to 40 of your favorite AM/FM radio stations and XM channels as presets.
40 Listening to the Radio —Continued Note: Hardware and required basic monthly subscription sold separately . Premium Channels available at additional monthly cost. Installation costs and other fees and taxes, including a one-time activ ation fee may apply .
41 Listening to the Radio —Continued Signing Up for XM Satellite Radio Before you can use XM Satellite Radio, you must first sign up for an account. Y ou’ll need a major credit card and your XM Satellite Radio ID, which you can get from the A V receiv er, as explained below , or from the Passport System package and itself.
42 Listening to the Radio —Continued Selecting XM Channels from the Fr ont Panel: Selecting the Previous Channel: Displaying XM Radio Inf ormation The following information can be displayed: Notes: • If the category , artist, or song title is not av ailable, “- - -” will be displayed instead.
43 Listening to the Radio —Continued P ositioning the XM Passport System Y ou can check the signal strength of the XM radio signal and adjust the position of the XM Passport System accordingly . XM Radio Messages The following messages may appear while using XM radio.
44 Common Functions This section explains functions that can be used with an y input source. Y ou can adjust the brightness of the display . Y ou can adjust the bass and treble for the front speakers, except when the Direct or Pure Audio (not North Amer- ican models) listening mode is selected.
45 Common Functions —Continued W ith the sleep timer, you can set the A V receiver so that it turns off automatically after a specified period. To cancel the sleep timer , press the [SLEEP] button repeatedly until the SLEEP indicator disappears. To check the remaining sleep time, press the [SLEEP] b utton.
46 Using the Listening Modes F or a description of each listening mode, see “ About the Listening Modes” on page 48. Selecting on the A V Receiver ■ [PURE A UDIO] button (not North American model) This button selects the Pure Audio listening mode.
47 Using the Listening Modes —Continued The following table sho ws which listening modes can be used with each input signal format. : Only av ailable on 6.1/7.1-channel playback systems. Not av ailable while speaker set B is on. : Only av ailable on 7.
48 Using the Listening Modes —Continued The A V receiv er’ s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound.
49 Using the Listening Modes —Continued DTS-ES Matrix This mode is for use with DTS-ES Matrix soundtracks, which use a matrix-encoded back-channel for 6.1/7.1-channel playback. Use it with D VDs that bear the DTS-ES logo, especially those with a DTS-ES Matrix soundtrack.
50 Using the Listening Modes —Continued W ith the Late Night function, you can reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts ev en when listening at low volume lev els—ideal for watching movies late at night when you don’t w ant to disturb anyone.
51 Using the Listening Modes —Continued The Audio Adjust settings are explained belo w . Input Channel Settings ■ Multiplex This setting determines which channel is output from a stereo multiplex source. Use it to select audio channels or languages with multiplex sources, multilingual TV broadcasts, and so on.
52 Ad v anced Setup Speaker Distance To get the best from surround sound, it’ s important that the sound from each speaker reaches the listener at the same time. T o achie ve this, you need to specify the dis- tance from each speaker to the listening position.
53 Adv anced Setup —Continued Speaker Levels W ith this function, you can adjust the volume of each speaker so that all speakers can be heard equally at the listening position.
54 Adv anced Setup —Continued Speaker Configuration This section explains ho w to specify which speakers are connected and their sizes. For speakers with a cone diameter larger than 6-1/2 inches (16 cm), specify Large (full band) . For those with a smaller diameter , specify Small (default crossov er 100 Hz) .
55 Adv anced Setup —Continued Crosso ver Frequency This setting only applies to the speakers that you speci- fied as Small in the “Speaker Configuration” on page 54.
56 Adv anced Setup —Continued The following table sho ws the display indicator for each digital signal format. Normally , the A V receiver detects the signal format auto- matically .
57 Recor ding This section explains ho w to record the selected input source to a component with recording capability , and how to record audio and video from dif ferent sources. Y ou can only record to a component that’ s connected to the T APE OUT or VIDEO 1 OUT jacks.
58 Contr olling Other Components Y ou can use the A V recei ver’ s remote controller (RC-649M) to control your other A V components, including those made by other manufacturers. This sec- tion explains ho w to enter the necessary remote control code for the component that you want to control (e.
59 Controlling Other Components —Continued Onkyo components that are connected via are con- trolled by pointing the remote controller at the A V receiv er, not the component. This allows you to control components that are out of view , in a rack, for example.
60 Controlling Other Components —Continued To control another component, point the r emote controller at it and use the buttons explained below . (Y ou must select the appropriate r emote control mode first.) W ith some A V components, certain buttons may not work as expected, and some may not work at all.
61 Tr oubleshooting If you hav e any trouble using the 7.1ch Home Theater System, look for a solution in this section. Can’t turn on the A V receiver • Make sure that the po wer cord is plugged into the wall outlet properly . • Unplug the power cord from the w all outlet, wait 5 seconds or more, then plug it in again.
62 Tr oubleshooting —Continued • The surround back speakers are not used with all lis- tening modes. Select another listening mode (page 48). • Not much sound may be produced by the surround back speakers with some sources. • Make sure the speakers are configured correctly (page 54).
63 Tr oubleshooting —Continued Reception is noisy , stereo FM reception suffers from hiss, or the FM STEREO indicator doesn’t appear • Relocate your antenna. •M ove the A V receiver a way from your TV or com- puter . • Listen to the station in mono (page 38).
64 Tr oubleshooting —Continued The following settings can be made for the S-Video and composite video inputs Y ou must use the buttons on the unit to make these set- tings. 1. While holding down the input selector b utton for the input source that you want to set, press the [SETUP] button.
65 Specifications Amplifier Section Video Section T uner Section ■ FM ■ AM General ■ Video Inputs ■ Video Outputs ■ A udio Inputs ■ A udio Outputs Rated Output Po wer (FTC) All channels: 110 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven at 1 kHz, with a maximum total harmonic distortion of 0.
66 Specifications —Continued ■ Po wered Subwoofer (SKW -540) ■ Front Speaker (SKF-540F) ■ Center Speaker (SKC-540C) ■ Surround Speaker (SKM-540S/SKB-540) Specifications and appearance are subject to change without prior notice.
67 Memo HT-S790_En.book Page 67 Friday, February 17, 2006 3:28 PM.
68 SN 29344189 I0602-1 Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8124 ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.
C s C t F r S v D e E s E n I t N l Remote Contr ol Codes 1. While holding down the REMO TE MODE button that y ou want to set, press the [DISPLA Y] button f or 3 seconds. 2. Use the number buttons to enter the 4-digit remote contr ol code. Codes de télécommande 1.
2 D VD Codes DVD D VD Player Acoustic Solutions 0730, 0713 Advent 1016 Aiwa 0641 Akai 0899, 1115 Akura 0898 Amoisonic 0835 Amphion Media Wor k s 0872 Amstrad 0713 AMW 0872 Apex Digital 0755, 0794, 083.
3 CD/MD/CDR/HDD Codes M D/CDR HDD C D CD Player Anthem 0897 Bush 0388 Carver 0179 Classic 1297 Copland 0393 Denon 0034, 0766 Dynamic Bass 0179 Fisher 0179, 1325 Garrard 0393 Genexxa 0426 GoldStar 1208.
4 TV Codes TV TV 888 0264 Acura 0009 Addison 0653, 0108, 0092, 1150 Admiral 0463, 0163 Advent 0761, 0783, 0815, 0842 Aiko 0092 Aiwa 0701, 1180 Akai 0060, 0812, 0702, 0030, 0264, 0218, 0009, 0208, 0672.
5 TV GE 0047, 0051, 0451, 0180, 0030, 1447, 1454, 0560, 0092, 1147, 1347 GEC 0037 Geloso 0009 Genexxa 0218, 0163 Gibralter 0017, 0030 Gintai 1150 Go Video 0886 GoldStar 0154, 0030, 0037, 0001, 0056, 0.
6 TV Codes TV TV NEC 0154, 0156, 0051, 0053, 0030, 0264, 0508, 0009, 0056, 0170, 1150, 1182, 1378, 1456 Neck er mann 0556, 0037 NEI 0037 Netsat 0037 New av e 0009, 0092, 0161, 1150 Nikkai 0037, 0264, .
7 TV T eac 0037, 0698, 0712, 0264, 0009, 0418, 1149 T echnics 0250, 0051 T echnisson 0714 T echwood 0051, 0056 T eco 0051, 0264, 0218, 0653, 0009, 0092 T eknika 0054, 0180, 0150, 0060, 0056, 0092 T el.
8 VCR Codes VCR VCR ABS 1972 Admiral 0209, 0479 Aiwa 0348, 0307, 0352, 0124, 0479, 1291 Akai 0041, 0315, 0175 Akiba 0072 Alba 0209, 0072, 0352, 0315 Alienware 1972 American High 0035 Amoisonic 0479 An.
9 VCR Sany o 0047, 0046, 0159, 1330 Saville 0352 Schaub Lorenz 0041 Schneider 0072 Scott 0184, 0121 Sears 0035, 0047, 0046, 1237 Seleco 0041 Sharp 0209, 0807, 0848, 1285 Shintom 0072 Singer 0072 Sonic.
10 CABLE/SA T Codes CABLE SA T Cable Con ver ter ABC 0003, 0008, 0033 Americast 0899 Amstrad 1222 Bell South 0899 British T elecom 0003 Cable & Wireless 1068 Clearmaster 0883 ClearMax 0883 Contec .
11 Satellite Receiver Hirschmann 0173 Hisense 1535 Hitachi 0819, 1250, 1284, 1525 HTS 0775, 1775 Hughes 0749, 1749, 1442 Hughes Network Systems 1142, 0749, 1749, 1442, 1443, 1444 Humax 1176, 1427, 167.
12 SN 29344188A I0603-2 647 Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8124 ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Onkyo SKM-540S c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Onkyo SKM-540S - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Onkyo SKM-540S, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Onkyo SKM-540S va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Onkyo SKM-540S, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Onkyo SKM-540S.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Onkyo SKM-540S. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Onkyo SKM-540S ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
