Manuel d'utilisation / d'entretien du produit 033 du fabricant Olympus
Aller à la page of 44
For the digital camera Stylus 720 SW, µ 720 SW ■ Thank you for buying the Underwater Case PT-033. ■ Please read this instruction manual carefully and use the product safely and correctly. ■ Please keep this instruction manual for reference after reading it.
E-1 Introduction ● Unauthorized copying of this manual in part or in full, except for private use, is prohibited. Unauthorized reproduction is strictly prohibited. ● OLYMPUS IMAGING CORP. shall not be responsible in any way for lost profits or any claims by third parties in case of any damage occurring from unsuitable use of this product.
E-2 1. Keep this product out of the reach of babies, infants, and children. There is the possibility of occurrence of the following types of accidents. Injury by dropping onto the body from a height. Injury from parts of the body getting caught in parts which open and close.
E-3 Batteries ● Use only an Olympus lithium-ion rechargeable battery (LI-42B) with the camera. ● Take care that the battery electrodes do not become wet. This may cause trouble or accidents. ● Carefully read the instruction manual for the camera about other cautions regarding batteries.
E-4 When water leakage occurs while this product is being used, repair of the camera housed in this product may become impossible. Please observe the following cautions for use.
E-5 Handling the Product ● Use or storage of the product at the following locations may cause defective operation, defects, trouble, damage, fire, internal clouding, or water leakage. Always avoid these locations. Locations reaching high temperatures such as those under direct sunlight, in an automobile, etc.
E-6 ● Do not perform operations other than specified in this instruction manual, do not remove or modify parts other than specified, and do not use parts other than specified. Any troubles in taking pictures or with the equipment resulting from the above actions shall be outside the guarantee.
E-7 Introduction ................................................................................E-1 Please read the following items before use ..............................E-1 For safe use ............................................................
E-8 Installation and Removal of the LCD Hood ..............................E-21 Installation ............................................................................E-21 Removal .....................................................................
E-9 1. Preparations Check the contents of the package. Check that all accessories are in the box. Contact your dealer if accessories should be missing or damaged.
E-10 Names of the parts Note : The Case operation parts marked by ❈ corresponds to the operation parts of the digital camera. When the operation parts of the Case are operated, the corresponding functions of the digital camera will operate. For details of the functions, refer to the instruction manual for the digital camera.
E-11 Install the strap on the Case body. : Please install the strap correctly as shown above. OLYMPUS IMAGING CORP. shall bear no responsibility for damage etc. caused by dropping the Case because of incorrect installation of the strap. CAUT ION :• Do not exert excessive force onto the lens window or the lens ring.
E-12 How to Press the Shutter When pressing the shutter lever, press it gently, so that there will be no movement of the camera. Note: • For detailed operation of the shutter, refer to the instruction manual for the digital camera.
E-13 2. Adv ance Check of the Case Advance test before use This Case has been the subject of thorough quality control for the parts during the manufacturing process and thorough function inspections during the assembly.
E-14 3. Install the digital camera. Check the digital camera. Check the digital camera before loading it in the Case. Battery Confirmation The flash is used very frequently during underwater shooting. Make sure that you have enough remaining battery power.
E-15 Prepare the camera. Applicable Digital Cameras This product (PT-033) is designed exclusively for use with the Stylus 720 SW and µ 720 SW digital cameras. Turn the digital camera ON. The digital camera can be switched ON by pressing the camera’s POWER button once.
E-16 Confirm that the digital camera is OFF and insert the digital camera gently into the Case. :• If the digital camera is not inserted properly, it may not be possible to seal the case so that it is airtight. Alternatively, some controls may become inoperable.
E-17 Insertion of silica gel Before sealing the Case, insert the accessory silica gel bag for prevention of fogging between the bottom of the camera and the Case. :• Insert the silica gel all the way at the specified location and with the specified orientation.
E-18 Seal the Case. Make sure the camera is loaded properly. :• Seal the Case by turning both buckle lock levers down in arrow direction. When one of the buckles is left open, the Case will not be sealed and water leakage will be caused. CAUT ION Gently close the rear lid (so that the O-ring does not slip out of the groove).
E-19 After sealing the Case, make sure the camera is functioning properly. 1. Press the POWER button on the Case and confirm that the camera turns ON/OFF. 2. Press the / /SCN button on the Case and confirm that the camera modes switch properly. 3. Press the shutter lever on the Case and confirm that the camera shutter releases.
E-20 When using the Case, current shooting scene and shooting mode information should be confirmed by checking the shooting scene/shooting mode indicators displayed on the camera’s LCD monitor. Confirm the shooting scene and shooting mode Shooting scene/shooting mode indicators PT033_E.
E-21 Installation and Removal of the LCD Hood Installation Strongly push the mounting projections of the LCD hood as shown in the figure into the guides above and below the LCD monitor window. Removal Remove the mounting projections of the LCD hood from the guides above and below the LCD monitor window by widening the LCD hood.
E-22 Perform the final checks. Visual Inspection After sealing the Case, check the sealing part of front and rear lid visually to confirm that the O-ring is not twisted or out of the groove and that no foreign matter has been caught. Fit the lens cap onto the lens ring as shown in the figure.
E-23 Now everything is all right! Have a nice dive! Final Test The final test after loading the camera is explained below. This is the only way to eliminate worry about possible entry of water! Always perform this test. It can be performed easily in a water tank or a bathtub.
E-24 4. T aking Pictures Under Water How to Use the Hand Strap Pass your hand through the accessory hand strap and adjust the length with the stop button. Take pictures carefully. Confirm the picture on the LCD monitor. This Case uses the LCD monitor to confirm the picture.
E-25 5. Underwater Shooting According to the Scene T ype Underwater shooting modes Suitable for shooting a scene that extends across a wide range such as a school of fish swimming through the water. Background blues are vividly reproduced. The camera incorporates the following shooting scene modes.
E-26 How to select the shooting scene Press the / /SCN button on the Case to set the camera mode to the SCN (Scene) mode. When the selection display appears, press the Up/Down cross-cursor buttons to select Underwater Wide- angle 1, Underwater Wide-angle 2 or Underwater Macro.
E-27 6. Handling After Shooting Wipe off any waterdrop. After completing the shooting and returning to land, wipe off any waterdrop sticking to the Case. Use air or a soft cloth not leaving any fibers to thoroughly wipe any waterdrop etc. from the joint between the front and rear lid, the shutter lever, the palm grips, and the buckles.
E-28 Take out the digital camera. Open the Case carefully and take the digital camera out. :• Always place the opened Case with the O-ring side facing up. If the Case is placed with the O-ring side facing down, dirt or other foreign matter may get on the O-ring or the O-ring contact surface and may allow water penetration during the next dive.
E-29 Wash the Case with pure water. After use, seal the Case again after taking out the camera and wash it sufficiently in pure water as soon as possible. After use in sea water, it is effective to immerse it for a fixed time in pure water to remove any salt.
E-30 7. Maintaining the W aterpr oof Function Remove the O-ring. Open the Case and remove the O-ring from the Case. Removal of the O-ring Insert the O-ring remover between the O-ring and the O-ring groove. Pass the tip of the inserted O-ring remover below the O-ring.
E-31 :• Maintenance of the waterproof functions is required even before using this product underwater for the first time. •W hen a mechanical pencil or a similar other sharp object is used to remove the O-ring or to clean the inside of the O-ring groove, the Case and the O-ring may be damaged and water leakage may be caused.
E-32 1 Install the O-ring. Confirm that no foreign matter is attached, apply a thin coat of the accessory grease to the O-ring, and fit the O-ring into the groove. At this time, confirm that the O-ring does not stick out from the groove. How to Apply Grease to the O-ring Apply the exclusive lubricant to each O-ring.
E-33 Replace consumable products. The O-ring is a consumable product. Independent of the number of times the Case is used, it is recommended that the O-ring should be replaced by a new one at least once a year. Deterioration of the O-ring is accelerated by the use conditions and the storage conditions.
E-34 8. Appendix Q & A on the use of the PT-033 Q1 : What digital camera models can be used with this product? A1 : This product (PT-033) is designed exclusively for use with the Stylus 720 SW and µ 720 SW digital cameras.
E-35 (c) Places with volatile substances (d) Places with vibrations (3) In case of the following handling with a camera loaded into the Case, trouble or breakage may be caused for the Case and/or the loaded camera.
E-36 Case under direct sunlight. Exposure to high temperatures or direct sunlight may cause deformation, discoloration or breakage of the Case and deterioration of the O-ring. Wipe the inside of the Case with a soft cloth not causing any fibers. Remove the O-ring, wipe off any salt, sand, dust, etc.
E-37 (6) Catching of the strap, the bag of silica gel, etc. at the time of sealing the Case (7) Throwing the Case from a boat into the water, jumping with the Case into the water, or other sudden application of strong forces onto the Case. When entering the water, hand the Case over quietly or avoid impacts in other ways.
E-38 water is sufficient. • Do not use commercial defogging agents. Always use the original Olympus defogging silica gel. • Do not use adhesive for repairs or other purposes. When repair is required, please contact a service station of our company or your dealer.
E-39 Specifications ❈ We reserve the right to change the external appearance and the specifications without notice. Available models Olympus digital camera Stylus 720 SW, µ 720 SW Pressure resistan.
E-40 MEMO PT033_E.qxd 06.2.23 8:36 PM ページ E-40.
E-41 MEMO PT033_E.qxd 06.2.23 8:36 PM ページ E-41.
E-42 MEMO PT033_E.qxd 06.2.23 8:36 PM ページ E-42.
PT033_E.qxd 06.2.23 8:36 PM ページ E-43.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Olympus 033 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Olympus 033 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Olympus 033, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Olympus 033 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Olympus 033, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Olympus 033.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Olympus 033. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Olympus 033 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
