Manuel d'utilisation / d'entretien du produit NV-T2DF du fabricant Nuvo
Aller à la page of 25
.
ENGLISH Danger Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably to noise induced hearing loss but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time.
GROUND CLAMPS GROUND CLAMPS ELECTRIC SERVICE ENTRANCE ELECTRIC SERVICE ENTRANCE ANTENNA DISCHARGE UNIT NEC SECTION 810-20 GROUNDING CONDUCTORS ANTENNA DISCHARGE UNIT NEC SECTION 810-20 GROUNDING CONDU.
L L OUT AUX IN R R TRIGGER ON=+12V AUDIO OUTPUT TUNER B TUNER A OUT AUDIO OUTPUT RS 232 ANTENNA INPUT IN USE ONL Y NuVo NV-T2P AS POWERED ANTENNA SYSTEM TRIGGER ON=+12V AUX IN Model NV -T2DF Dual XM Tuner NuVo Techonlogies LLC • Cincinnati Ohio USA www.
Front P anel 1. Stand-by LED: This LED (Light Emitting Diode) indicates that the T2 is plugged into an AC power source. 2. Remote Sensor: This IR (Infrared) receiver allows wireless remote control of the T2 functions. This IR input is active, even when it is used in conjunction with the direct IR input on the back panel.
Back P anel 1. Antenna Input: Coax “F” connector brings in the signal input from the NuVo NV-T2P AS antenna (pg. 10). 2. Aux. Input: This stereo RCA connector is enabled through the advanced menu options (pg. 14), and allows an additional audio source to be connected and accessed through the tuner source selection.
NV-T2RC3 Remote Control 1. P ower: The power button turns the selected tuner on and off . 2. Scroll Buttons: These buttons are the equivalent of turning the front panel Select knob. The top button is the equivalent of turning the knob clockwise, and the bottom button is the equivalent of counterclockwise.
I. Installing the NV-T2DF Dual T uner Stereo Audio Connections Each tuner has two audio output jacks. One is a stereo RCA connection, and the other is a stereo 3.5mm mini. The RCA output is an individual left and right channel connection made with a standard RCA cable.
IR Pass-Thru The mini jack labeled “IR pass-thru" mini connection is used for connecting forwarded IR signals to an audio component connected to the auxiliary audio input. Using the Aux. Input The T2 is equipped with an auxiliary audio input labeled “ AUX IN.
Antenna Input The T2 ships with a proprietary amplified AM/FM antenna. This antenna is designed to work only with the NuV o T2 series tuners. It can be located up to 200 feet from the tuner location, and we recommend 75-ohm RG 6 coaxial cable with a standard F style connector on each end.
II. Front P anel Menu Controls The T2 has many settings available in the menus. This allows for many specialized set up options for basic tuner operation.
The following menu selections are not necessary for standard tuner operation, but do provide a deeper level of control for those who need it. When you scroll to “ Advanced Settings” in the menu, p.
Audio Settings These selections are intended for some stand-alone applications. They should be left at default settings for NuV o audio systems. These systems allow identical audio control on a per-zone basis. Bass EQ: Bass output can be adjusted +12 dB or down to 12 dB.
AUX Input Disable/Enable: The T2 has an auxiliary audio input that allows access through either of the tuners to an additional audio source. T o use this you must first enable the input in the menu options. AUX Gain: The audio input from an auxiliary source can be adjusted to match the output of the T2's T uner A and T uner B.
III. Stand-alone Front P anel Use of the T2 T uning a Desired Station: Pressing the Select knob cycles through the tuning modes. Step T une Mode: Each of the T2's tuners default to step tune mode.
Actual use of these data fields is not regulated, and they may vary significantly in content between stations. If you choose not to have RDS information displayed, pressing the “Display” button will then indicate “RDS receive OFF”.
IV . Using the T2 with the Concerto NuV oNet Setting Up the T uner for NuVoNet The T2 must be set for one of the Concerto source inputs 1-6. This can be done at the front panel when the tuner is first turned on, in the T2 Configurator software, or through the front panel advanced menu.
Operating the T2 with the Concerto Display Pad By following the previous steps you should now be able to operate the T2 from any of the Concerto Display P ads. The Concerto Display Pads have secondary tuner functions silk-screened on the bezel below the associated keys.
T2 Configuration Sof tware Basic setup and operation of the T2 is easily done from the front panel, the included T2RC3 remote, or the Concerto Display P ad.
2.2 Regional Setup 2. 3 Brightness 2.4 Aut o-On Page 20 2.2 Regional Setup: Depending on your geographic location, the tuner needs to be set for the proper tuning standard.
3.3 R ename Bank 3.4 Erase Bank 3.2 Add Bank Page 21 3.2 Add Bank: If you want to add a bank of 10 presets, the “ Add Bank “ button will bring up a window that allows you to name the bank and automatically add it to the T2's presets. 3.3 Rename Bank: This button allows you to give a bank of presets a customized name.
4.1 C ustom Regional Setup Page 22 4.1 Custom Regional Setup: Some countries operate at a tuning standard outside the four preset regions. The Custom setting allows specific parameters. One determining factor for tuning is the “Pre-emphasis”. The two choices for this a are 50µS (microseconds) and 75µS.
4.5 A UX Input Page 23 4.5 AUX Input: The T2 has an additional input that allows an external device to be controlled through the T2's IR pass through. When this input is enabled, the level of the signal input can be adjusted up or down to match the tuners ' signal output level.
Page 24 6. 1 Categories T ab 6.2 FM Freqs: This tab lists all the available frequencies within the FM band. When highlighted, the Frequency Information on the right side of the tab allows you to name and categorize each desired frequency in up to four different categories.
Page 25 7 .2 Successful Download: When the download is complete a final window will appear indicating that all the information has downloaded successfully. Actual download time will vary based on your computer's processing capabilities. 7.2 S uccessful Down load NV-T2DF Specifications FM Section AM Section Tuning Range 87.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Nuvo NV-T2DF c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Nuvo NV-T2DF - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Nuvo NV-T2DF, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Nuvo NV-T2DF va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Nuvo NV-T2DF, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Nuvo NV-T2DF.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Nuvo NV-T2DF. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Nuvo NV-T2DF ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
