Manuel d'utilisation / d'entretien du produit 241-5101-200 du fabricant Nortel Networks
Aller à la page of 62
Passport Installation Guide 241-5101-200.
.
P asspor t 8250 Installation Guide Publication: 241-5101-200 Document status: Standard Document version: R2.2 Document date: October 1999 Copyright © 1999 Nortel Networks. All Rights Reserved. Printed in Canada NORTEL, NORTEL NETWORKS, the globemark design, the NORTEL NETWORKS corporate logo, and PASSPORT are trademarks of Nortel Networks.
.
5 Passport 8250 Installation Guide R2.2 Publication history October 1999 R2.2 Standard Commercial av ailability ..
6 Publication history 241-5101-200 R2.2.
7 Passport 8250 Installation Guide R2.2 Contents About this document 11 Who should read this guide 11 What you need to kno w 11 How this guide is organiz ed 11 Conv entions 12 Documentation conv entio.
8 Contents 241-5101-200 R2.2 Chapter 2 Preparing for the hardware installation 21 Selecting an installation site 21 Unpacking the P asspor t 8250 shipment 22 T aking inv entor y of the P asspor t 8250.
Contents 9 Passport 8250 Installation Guide R2.2 Appendix A Replacing hardware 45 Replacing a pow er supply module 46 Replacing a board module 47 P asspor t 8250 board guidelines 49 Replacing the f an.
10 Contents 241-5101-200 R2.2.
11 Passport 8250 Installation Guide R2.2 About this document This document explains ho w to install the Passport 8250 de vice. This document uses the terms DS-1/E1 and STM-1/OC-3. The term DS-1/E1 is for information that applies to both DS-1 and E1 interfaces.
12 About this document 241-5101-200 R2.2 • “Replacing hardware” (page 45). • “LEDs” (page 51). • “Standards” (page 55). Con ventions There are documentation and symbol con ventions used in this document. Documentation con ventions There are a number of documentation con ventions you should kno w about.
About this document 13 Passport 8250 Installation Guide R2.2 • ... Three dots in a command indicate that the parameter may be repeated more than once in succession.
14 About this document 241-5101-200 R2.2 NMS documents See the follo wing NMS documents for information on how to monitor and configure the Passport 8250 de vice using the NMS Passport 8250 tools, integrating the P assport 8250 device into the NMS en vironment, and using backup and restore: • NTP 241-6001-028, NMS P assport 8250 T ools Guide .
15 Passport 8250 Installation Guide R2.2 Chapter 1 P asspor t 8250 This section describes the Passport 8250 de vice. Y ou can view the follo wing topics in this section: • “Passport 8250 functions.
16 Chapter 1 Passport 8250 241-5101-200 R2.2 Figure 1 P asspor t 8250 device The Passport 8250 can be used for the follo wing applications: • Providing medium to high density DS-1 or E1 ingress to an A TM carrier network. • Providing medium to high density DS-1 or E1 ingress to an A TM wireless network.
Chapter 1 Passport 8250 17 Passport 8250 Installation Guide R2.2 See “Passport 8250 front panel” (page 17) for an illustration of the hardware components. Figure 2 P asspor t 8250 fr ont panel Board modules The Passport 8250 de vice has a field-replaceable network board and up to three field-replaceable DS-1/E1 service boards.
18 Chapter 1 Passport 8250 241-5101-200 R2.2 Communication ports The communication ports, which are located on the network board, include a serial port, ethernet port, and redundant A TM uplink port. Serial port The serial port connects the Passport 8250 de vice to a local host using a RS-232 cable.
Chapter 1 Passport 8250 19 Passport 8250 Installation Guide R2.2 P asspor t 8250 software Y ou do not have to order softw are for the Passport 8250. The Passport 8250 comes preloaded with the operating system and the applications it needs.
20 Chapter 1 Passport 8250 241-5101-200 R2.2.
21 Passport 8250 Installation Guide R2.2 Chapter 2 Preparing f or the har dware installation This section provides the following procedures for preparing for installing the Passport 8250 de vice: 1 .
22 Chapter 2 Preparing for the hardware installation 241-5101-200 R2.2 — Access is through the use of a special tool, or lock and key , or other means of security , and is controlled by the authority responsible for the location.
Chapter 2 Preparing for the hardware installation 23 Passport 8250 Installation Guide R2.2 Ta b l e 1 In ventory checklist Item Options available Code # Chassis One option available.
24 Chapter 2 Preparing for the hardware installation 241-5101-200 R2.2 Getting the tools to mount the chassis in a rac k T o mount the chassis in a rack, you will need one or more of the follo wing tools: • 9.5 mm wide flat-bladed screwdri ver for 19” or ETSI rack installation.
25 Passport 8250 Installation Guide R2.2 Chapter 3 Installing the P asspor t 8250 device This section provides the follo wing procedures for installing the Passport 8250 de vice: 1 “Mounting the chassis in a rac k” (page 25). 2 “Connecting cables to the ports” (page 29).
26 Chapter 3 Installing the Passport 8250 device 241-5101-200 R2.2 • Allo w at least 2 inches of ventilation space on both sides of the de vice as illustrated in “V entilation space” (page 26). • Do not block the air flo w around the device with cables.
Chapter 3 Installing the Passport 8250 device 27 Passport 8250 Installation Guide R2.2 Figure 4 Attaching mounting brac kets to chassis Figure 5 Installing the chassis on a 19” rac k Secure mounting brac kets to the unit using the fixing holes indicated T emporary fixing f or installation aid Allow a minimum of 2SU (88.
28 Chapter 3 Installing the Passport 8250 device 241-5101-200 R2.2 Mounting the P asspor t 8250 de vice on a NEBS or ETSI rack 1 Locate the brac ket mounting holes on each side of the chassis. 2 Attach the mounting brac kets to each side of the chassis using a Pozidriv e screw driv er .
Chapter 3 Installing the Passport 8250 device 29 Passport 8250 Installation Guide R2.2 Connecting cables to the ports Y ou hav e to connect cables to the following ports: • DS-1/E1 ports. For details on connecting cables, see “Connecting the DS-1/E1 ports” (page 29).
30 Chapter 3 Installing the Passport 8250 device 241-5101-200 R2.2 3 Connect the other end of the DS-1/E1 cable to the f ar end. Table 2 DS-1/E1 pin assignment Description Signal Pin Pin Signal Descri.
Chapter 3 Installing the Passport 8250 device 31 Passport 8250 Installation Guide R2.2 Connecting the ethernet port 1 Obtain the f ollowing equipment: • A regular RJ-45 ethernet cable with a male DB-8 connector and a 10 Base-T ethernet drop for a connection to a work station.
32 Chapter 3 Installing the Passport 8250 device 241-5101-200 R2.2 3 Connect the other end of the RJ-45 cable to a 10 Base-T ethernet drop or work station.
Chapter 3 Installing the Passport 8250 device 33 Passport 8250 Installation Guide R2.2 Connecting the A TM uplink por t 1 Obtain the f ollowing equipment: • Multi-mode fiber optic cables with SC co.
34 Chapter 3 Installing the Passport 8250 device 241-5101-200 R2.2 Figure 7 Dual power suppl y 1 Obtain the f ollowing equipment: • A -48 v DC power supply cable with 3W3-D connector for each power supply module. • Antistatic protection, such as an antistatic glov e.
Chapter 3 Installing the Passport 8250 device 35 Passport 8250 Installation Guide R2.2 The central contact is designated as the chassis ground. 4 Connect the -48v power supply cab le with the male 3W3-D connector to the f emale 3W3-D connector .
36 Chapter 3 Installing the Passport 8250 device 241-5101-200 R2.2 Exit and secure all cables to the left as illustrated in “Cables left of chassis” (page 36) or underneath the chassis as illustrated in “Cables underneath chassis” (page 36).
37 Passport 8250 Installation Guide R2.2 Chapter 4 Configuring the P asspor t 8250 for operations This section provides the follo wing procedures for configuring the Passport 8250 de vice for the op.
38 Chapter 4 Configuring the Passport 8250 for operations 241-5101-200 R2.2 a. F or each power supply module, turn the power supply breaker to ON. The LEDs on each power supply module is on. T ext is displa yed on the h yper ter minal screen. 3 From the hyperterminal session, stop the Passport 8250 de vice from starting-up: a.
Chapter 4 Configuring the Passport 8250 for operations 39 Passport 8250 Installation Guide R2.2 See “Boot command parameters” (page 39) for the boot parameters you need to configure. Viewing the boot parameter s T o display the e xisting boot parameters, T ype the bootconfig command without the [set] parameter .
40 Chapter 4 Configuring the Passport 8250 for operations 241-5101-200 R2.2 4 F or host inet, type the IP address of the remote host. 5 If the remote host is on a diff erent network, type the IP address of the gateway node at the gateway inet prompt. 6 F or user , type the FTP userid of the remote host.
Chapter 4 Configuring the Passport 8250 for operations 41 Passport 8250 Installation Guide R2.2 where [set] configures the clocking scheme for the Passport 8250 de vice. For details on the clockconfig parameters, see “Clockconfig command parameters” (page 41).
42 Chapter 4 Configuring the Passport 8250 for operations 241-5101-200 R2.2 Setting the cloc king scheme to External Primary 1 Displa y the clockconfig parameters: clockconfig [set] 2 F or Exter nal Primar y Board Number , enter a board number . 3 F or Exter nal Primar y P or t Number , enter a por t number .
Chapter 4 Configuring the Passport 8250 for operations 43 Passport 8250 Installation Guide R2.2 [E1-1]: clockconfig set External Primary Board Number (0 - 3) = 0 2 External Primary Port Number (1 - 16.
44 Chapter 4 Configuring the Passport 8250 for operations 241-5101-200 R2.2 clockconfig [set] 2 F or Exter nal Primar y Board Number , enter a board number . 3 F or Exter nal Primar y P or t Number , enter a por t number . 4 F or Exter nal Secondary Board Number, enter a board n umber .
45 Passport 8250 Installation Guide R2.2 Appendix A Replacing har dware This section provides instructions on how to replace hardware components on the Passport 8250 de vice.
46 Appendix A Replacing hardware 241-5101-200 R2.2 Replacing a power suppl y module The Passport 8250 de vice is powered by tw o power supply modules. If a po wer supply module stops operating, you need to immediately replace it with a dummy power supply filler pack to ensure proper cooling and air flo w .
Appendix A Replacing hardware 47 Passport 8250 Installation Guide R2.2 4 Slide the power supply module or dumm y power supply filler pac k out of the slot. 5 Insert the new po wer supply module or dummy power supply filler pack into the empty power supply slot.
48 Appendix A Replacing hardware 241-5101-200 R2.2 Figure 11 Board slots 1 F or each power supply module, set the po wer supply breaker to off . 2 Flip the lock hatch at each end of the circuit board slot open. 3 Slide the network board or ser vice board out of the circuit board slot.
Appendix A Replacing hardware 49 Passport 8250 Installation Guide R2.2 P asspor t 8250 boar d guidelines Use caution when handling, storing, and transporting circuit boards. Follo w these guidelines: • Do not stack or store boards without first replacing them in their antistatic material and shipping material.
50 Appendix A Replacing hardware 241-5101-200 R2.2 The f ans continue to rotate for a f ew seconds. 4 Remov e the new f an module from the package . 5 Inser t the new f an module into the empty fan module slot. 6 Tighten the two securing screws on the f an module.
51 Passport 8250 Installation Guide R2.2 Appendix B LEDs The LEDs located on the front panel of the Passport 8250 de vice. See “Passport 8250 LEDS” (page 52) for an illustration of the LEDs and “LEDs description” (page 53) for a description of the LEDs on the illustration.
52 Appendix B LEDs 241-5101-200 R2.2 Figure 12 P asspor t 8250 LEDS 5 1 2 3 4 F an module Network board P ower supply 1 P ower supply 2 Ser vice boards 876 5.
Appendix B LEDs 53 Passport 8250 Installation Guide R2.2 Ta b l e 5 LEDs description Item color Description 1 green on = system initialized and software loaded 2 red on = All provisioned CES connectio.
54 Appendix B LEDs 241-5101-200 R2.2.
55 Passport 8250 Installation Guide R2.2 Appendix C Standar ds This section describes the standards the Passport 8250 de vice meets. Y ou can view the follo wing topics in this section: • “Product.
56 Appendix C Standards 241-5101-200 R2.2 — FCC Part 15, Class A (USA) — ICES-003, Class A (Canada) — EN 55022, Class A (Europe) • Immunity , ESD, EFT (EU) — EN50082-1 — EN300 386-2 — Be.
Appendix C Standards 57 Passport 8250 Installation Guide R2.2 Federal Comm unications Commission (FCC) The Passport 8250 de vice complies with Part 68 of the FCC rules. On the top of this equipment is a label that contains, among other information, the FCC registration.
58 Appendix C Standards 241-5101-200 R2.2 Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company . The equipment must also be installed using an acceptable method of connection.
59 Passport 8250 Installation Guide R2.2 C Cable connections A TM uplink port 33 Ethernet port 31 Serial port 32 T1/E1 ports 29 Chassis assembly Installing on 19" rack 26 Installing on NEB or ETS.
60 Index 241-5101-200 R2.2.
.
P asspor t 8250 Installation Guide R2.2 Copyright © 1999 Nortel Networ ks . All Rights Reserved. NORTEL, NOR TEL NETWORKS, the globemark design, the NORTEL NETW ORKS corporate logo, and P ASSPORT are trademarks of Nor tel Networks. Publication: 241-5101-200 Document status: Standard Document version: R2.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Nortel Networks 241-5101-200 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Nortel Networks 241-5101-200 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Nortel Networks 241-5101-200, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Nortel Networks 241-5101-200 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Nortel Networks 241-5101-200, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Nortel Networks 241-5101-200.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Nortel Networks 241-5101-200. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Nortel Networks 241-5101-200 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
