Manuel d'utilisation / d'entretien du produit vehicle du fabricant Nissan
Aller à la page of 384
W elcome to the growing family of new NISSAN owners. This vehicle is delivered to you with confidence. It was produced using the latest techniques and strict quality control. This manual was prepared to help you under- stand the operation and maintenance of your vehicle so that you may enjoy many miles (kilome- ters) of driving pleasure.
This manual includes information for all options available on this model. Therefore, you may find some information that does not apply to your vehicle. All information, specifications and illustrations in this manual are those in effect at the time of printing.
NISSAN CARE S... Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Y our satisfaction with your vehicle and your NISSAN dealer are our primary concerns. Y our NISSAN dealer is always available to assist you with all your automobile sales and service needs.
Z REVIEW COPY— 2007 Quest (van) Owners Manual—USA_English (nna) 02/24/06—debbie X.
T able of Contents Illustrated table of contents Safety—Seats, seat belts and supplemental restraint system Instruments and controls Pre-driving checks and adjustments Display screen, heater, air co.
Z REVIEW COPY— 2007 Quest (van) Owners Manual—USA_English (nna) 02/24/06—debbie X.
0 Illustrated table of contents Airbags, seat belts and child restraints ...............0 - 2 Exterior front ......................................0 - 3 Exterior rear .......................................0 - 4 Passenger compartment .................
1. 3rd row bench center seat belt (P . 1-15) 2. 3rd row bench seat belts (P . 1-15) 3. T op tether strap anchor points (P . 1-30) 4. 2nd row captain’s chair seat belts (P . 1-15) 5. Front seat belts (P . 1-15) 6. Supplemental curtain side-impact air bag (P .
1. Engine hood (P . 3-14) 2. Headlight and turn signal switch (P . 2-19) 3. Replacing bulbs (P . 8-27) 4. Windshield wiper and washer switch (P . 2-17) 5. Windshield (P . 8-17) 6. P ower windows (P . 2-38) 7. Door locks, keyfob, keys (P . 3-3, 3-9, 3-2) 8.
1. Rear window defroster switch (P . 2-18) 2. V ehicle loading (P . 9-12) 3. Lift gate (P . 3-14) 4. Lift gate release (P . 3-18) 5. Rear view monitor (if so equipped) (P .4-29) 6. Replacing bulbs (P . 8-27) 7. Fuel-filler cap, fuel recommendation (P .
1. DVD entertainment system (if so equipped) (P . 4-62) 2. Personal lights (P . 2-44) 3. Skyview roof (if so equipped) (P . 2-41) 4. Sunroof (if so equipped) (P . 2-41) 5. Map lights (P . 2-45) , Console light P .2-45) 6. Sun visors (P . 3-22) 7. HomeLink T (if so equipped) (P .
1. V entilators (P . 4-31) 2. Headlight/fog light (if so equipped)/turn signal switch (P . 2-19) 3. Steering wheel switch for audio control/Bluetooth T hands-free phone system (if so equipped) (P . 4-59) 4. Driver supplemental air bag/horn (P . 1-51, P .
17. Shift selector lever (P . 5-10) 18. Ignition switch (P . 5-8) 19. Tilt steering wheel control (P . 3-21) 20. Rear sonar system off switch (if so equipped) (P . 2-26) 21. V ehicle dynamic control (VDC) off switch (if so equipped) or T raction con- trol system (T CS) off switch (if so equipped) (P .
1. P ower steering fluid reservoir (P . 8-11) 2. Engine oil filler cap (P . 8-8) 3. Air cleaner (P . 8-16) 4. Brake fluid reservoir (P . 8-12) 5. Battery (P . 8-13) 6. Fuse/fusible link box (P . 8-20) 7. T ransmission dipstick (P . 8-11) 8. Engine oil dipstick (P .
Warning light Name Page or Anti-lock brak- ing warning light 2-8 or Brake warning light 2-8 Charge warning light 2-8 Door open warning light 2-8 Engine oil pres- sure warning light 2-8 Low fuel warn- .
Indicator light Name Page Front passenger air bag status light 2-12 Security indica- tor light 2-13 Slip indicator light 2-13 Traction control system off indi- cator light (if so equipped) 2-13 Turn s.
1 Safety—Seats, seat belts and supplemental restraint system Seats ............................................1 - 2 Front manual seat adjustment (if so equipped) ................................1 - 2 Front power seat adjustment (if so equipped) ...
WARNING ● Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident, you could be thrown into it and receive neck or other serious injuries. Y ou could also slide under the lap belt and receive serious internal injuries.
Forward and backward Pull the lever up and hold it while you slide the seat forward or backward to the desired position. Release the lever to lock the seat in position. Reclining T o recline the seatback, pull the lever up and lean back. T o bring the seatback forward, pull the lever up and lean your body forward.
Lumbar support (driver’s seat) The lumbar support feature provides lower back support to the driver. Move the lever up or down to adjust the seat lumbar area. FRONT POWER SEAT ADJUSTMENT (if so equipped) Operating tips ● The power seat motor has an auto-reset overload protection circuit.
belt fit (see “Precautions on seat belt usage” later in this section) . Also, the seatback can be re- clined to allow occupants to rest when the ve- hicle is stopped. Seat lifter (if so equipped for driver’s seat) Push the front or rear end of the switch up or down to adjust the angle and height of the seat cushion.
2ND ROW CAPTAIN’S CHAIR ADJUSTMENT Forward and backward WARNING ● The 2nd row seats are heavy. Be careful when folding and unfolding. ● T o avoid injury to yourself and others, keep hands and body clear when folding. While seated, pull the lever s 1 and hold it while you slide s 2 the seat forward or backward to the desired position.
Tip up for easy entry to the 3rd row The 2nd row captain’s chairs can be tipped for- ward for easy entry or exit from the 3rd row bench seat. T o enter the 3rd row bench seat , lift up on the lever located on the lower base of the 2nd row captain’s chair to tip the seat forward.
● Do not attach anything to the head re- straint stalks. Doing so could impair active head restraint function. The head restraint moves forward utilizing the force that the seatback receives from the occu- pant in a rear-end collision.
Adjust the head restraint so the center is level with the center of your ears. ARMRESTS T o use the armrests, pull them down to the rest- ing position. s A Resting position s B Stowed position Adjustable front seat armrest’s (if so equipped) T o use the adjustable seat armrest, pull it down to the resting position.
● If the head restraints are removed for any reason, they should be securely stored to prevent them from causing injury to passengers or damage to the vehicle in case of sudden braking or an accident. ● When returning the seatbacks to the upright position, be certain they are completely secured in the latched posi- tion.
s 1 Fold the 2nd row captain’s chairs to the floor for maximum cargo hauling, move the head restraints forward before folding. s 2 Lift up on the recline lever to fold the seat- back forward on the seat base. s 3 Push down on the small knob on the back of the seat to release the base of the seat.
Folding T o fold the seatback forward, for cargo hauling, lift up on the latch in the center of the seatback to fold the seatback over the seat base. Folding the 3rd row bench seat WARNING ● The 3rd row bench seat is heavy. Be careful when folding and unfolding.
3. Pull back on the pull strap to release the back of the seat. Rotate the seatback toward the back of the vehicle. 4. Pull up on the lever located on the back of the seat base. This will fold the seat base toward the back of the vehicle. 5. The entire seat will rotate toward you and stow in the floor.
6. The rear seat anchors are spring loaded and can be folded into the side panels to maxi- mize cargo space. The anchors are held in the folded position by the items in the cargo area. When the load is removed from the cargo area, the rear seat anchors automati- cally return to the unfolded position.
PRECAUTIONS ON SEAT BELT USAGE If you are wearing your seat belt properly ad- justed and you are sitting upright and well back in your seat with both feet on the floor, your chances of being injured or killed in an accident and/or the severity of injury may be greatly reduced.
WARNING ● Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be properly re- strained in the rear seat and, if appro- priate, in a child restraint. WARNING ● The seat belt should be properly ad- justed to a snug fit.
WARNING ● Always route the shoulder belt over your shoulder and across your chest. Never run the belt behind your back, under your arm or across your neck. The belt should be away from your face and neck, but not falling off your shoulder. ● Position the lap belt as low and snug as possible AROUND THE HIPS, NO T THE WAIST .
There are three basic types of child restraint systems: ● Rear facing child restraint ● Front facing child restraint ● Booster seat The proper restraint depends on the child’s size. Generally , infants up to about 1 year and less than 20 pounds (9 kg) should be placed in rear facing child restraints.
have a label certifying that it complies with Fed- eral Motor V ehicle Safety Standards or Canadian Motor V ehicle Safety Standards. Once the child has grown so the shoulder belt is no longer on or near the face and neck, use the shoulder belt without the booster seat.
s 2 Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until you hear and feel the latch engage. ● The retractor is designed to lock during a sudden stop or on impact. A slow pulling motion permits the seat belt to move, and allows you some freedom of movement in the seat.
Unfastening the seat belts s 1 T o unfasten the seat belt, press the button on the buckle. The seat belt automatically re- tracts. Checking seat belt operation Seat belt retractors are designed to lock seat belt movement by two separate methods: ● When the seat belt is pulled quickly from the retractor.
WARNING ● Always fasten the connector tongue and the seat belt in the order shown. ● Always make sure both the connector tongue and the seat belt tongue are secured when using the seat belt. Do not use it with only the seat belt tongue attached. This could result in serious personal injury in case of an accident or a sudden stop.
● If the rear center seat belt connector and the seatbacks are not secured in the correct position, serious personal injury may result in an accident or sud- den stop. Attaching the 3rd row center seat belt Always be sure the 3rd row center seat belt connector tongue and connector buckle are at- tached.
● When attaching the rear center seat belt connector, be certain that the seat- backs are completely secured in the latched position and the rear center seat belt connector is completely secured.
SEAT BELT EXTENDERS If, because of body size or driving position, it is not possible to properly fit the lap-shoulder belt and fasten it, an extender is available which is compatible with the installed seat belts. The ex- tender adds approximately 8 inches (200 mm) of length and may be used for either the driver or front passenger seating position.
WARNING ● Infants and small children should al- ways be placed in an appropriate child restraint while riding in the vehicle. Failure to use a child restraint can re- sult in serious injury or death. ● Infants and small children should never be carried on your lap.
CAUTION Remember that a child restraint left in a closed vehicle can become very hot. Check the seating surface and buckles before placing your child in the child restraint. This vehicle is equipped with a universal child restraint lower anchor system, referred to as the LA T CH (Lower Anchors and T ethers for CHil- dren) system.
LA T CH lower anchor point locations The LA T CH system anchors are located at the rear of the seat cushion near the seatback. A label is attached to the seatback to help you locate the LA T CH system anchors. WARNING ● Attach LA T CH system compatible child restraints only at the locations shown.
Installing child restraint LA T CH anchor attachments LA T CH compatible child restraints include two rigid or webbing-mounted attachments that can be connected to two anchors located at certain seating positions in your vehicle. This system is known as the LA T CH system.
T OP TETHER STRAP CHILD RESTRAINT If the manufacturer of your child restraint requires the use of a top tether strap, it must be secured to the anchor point. WARNING Child restraint anchor points are designed to withstand only those loads imposed by correctly fitted child restraints.
4. Tighten the tether strap according to the manufacturer’s instructions to remove any slack. For best child restraint fit, see the child restraint installation instructions in this section and the child restraint manufacturer’s instructions. 2nd row captain’s chairs (if so equipped) 1.
3rd row bench seat (if so equipped) 1. T op tether strap 2. Anchor point WARNING In the 3rd row bench seat, a child restraint with a top tether strap can only be used in the center position. Do not place in an outboard seating position and attempt to angle the tether strap to the center position.
CHILD RESTRAINT INSTALLATION USING LA T CH-2ND ROW CAPTAIN’S CHAIRS (if so equipped) WARNING ● Attach LA T CH system compatible child restraints only at the locations shown. For the LA T CH lower anchor locations see “LA T CH (Latch Anchors and T ethers for CHildren) system” .
with the proper child restraint fit, try another seating position or a different child restraint. 5. For child restraints that are equipped with webbing mounted attachments, remove any additional slack from the anchor attach- ments.
7. Before placing the child in the child restraint, hold the child restraint near the LA T CH at- tachment and use force to push the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 inch (25 mm) .
5. For child restraints that are equipped with webbing mounted attachments, remove any additional slack from the anchor attach- ments. Press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments.
CHILD RESTRAINT INSTALLATION USING LA T CH-3RD ROW BENCH SEAT (if so equipped) WARNING ● Attach LA T CH system compatible child restraints only at the locations shown. For the LA T CH lower anchor locations see “LA T CH (Latch Anchors and T ethers for CHildren) system” .
5. For child restraints that are equipped with webbing mounted attachments, remove any additional slack from the anchor attach- ments. Press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments 6.
8. Check to make sure the child restraint is properly secured prior to each use. If the child restraint is loose, repeat steps 3 through 8. Rear-facing Follow these steps to install a rear-facing child restraint in the 3rd row bench seats using LA T CH: 1.
6. Before placing the child in the child restraint, hold the child restraint near the LA T CH at- tachment and use force to push the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 inch (25 mm) .
● NISSAN recommends that child re- straints be installed in the rear seat. However, if you must install a forward- facing child restraint in the front pas- senger seat, move the passenger seat to the rearmost position. Also, be sure the front passenger air bag status light is illuminated to indicate the passenger air bag is OFF .
2. P osition the child restraint on the seat. Al- ways follow the child restraint manufactur- er’s instructions The back of the child restraint should be secured against the vehicle seat back. If necessary , adjust or remove the head restraint to obtain the correct child restraint fit.
5. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt. 6. Remove any additional slack from the seat belt; press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while pulling up on the seat belt.
8. Before placing the child in the child restraint, hold the child restraint near the seat belt path and use force to push the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 inch (25 mm) .
2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s in- structions for belt routing. 3. Pull on the shoulder belt until the belt is fully extended.
5. Remove any additional slack from the child restraint; press downward and rearward firmly in the center of the child restraint to compress the vehicle seat cushion and seat- back while pulling up on the seat belt.
PRECAUTIONS ON BOOSTER SEATS WARNING ● Infants and small children should al- ways be placed in an appropriate child restraint while riding in the vehicle. Failure to use a child restraint or booster seat can result in serious injury or death. ● Infants and small children should never be carried on your lap.
● After placing the child in the booster seat and fastening the seat belt, make sure the shoulder portion of the belt is away from the child’s face and neck and the lap portion of the belt does not cross the abdomen. ● Do not put the shoulder belt behind the child or under the child’s arm.
All U.S. states and Canadian provinces or territories require that infants and small children be restrained in an approved child restraint at all times while the vehicle is being operated. The instructions in this section apply to booster seat installation in the rear seats or the front passenger seat.
3. The booster seat should be positioned on the vehicle seat so that it is stable. If neces- sary , adjust or remove the head restraint to obtain the correct booster seat fit. See “Head restraint adjustment” earlier in this section. If the head restraint is removed, store it in a secure place.
7. If the booster is installed in the front passen- ger seat: When the ignition switch is turned to the ON position, the passenger air bag status light may or may not be illumi- nated, depending on the size of the child and the type of booster seat being used.
WARNING ● The supplemental front air bags ordi- narily will not inflate in the event of a side impact, rear impact, rollover, or lower severity frontal collision. Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents.
WARNING ● Never let children ride unrestrained or extend their hands or face out of the window. Do not attempt to hold them in your lap or arms. Some examples of dangerous riding positions are shown in the illustrations.
WARNING ● Children may be severely injured or killed when the supplemental front air bags, side air bags or curtain side- impact air bags inflate if they are not properly restrained. Pre-teens and chil- dren should be properly restrained in the rear seat, if possible.
WARNING ● Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the front seat. An in- flating supplemental front air bag could seriously injure or kill your child. See “Child restraints” earlier in this section for details.
WARNING ● The seat belts, the supplemental side air bags and curtain side-impact air bags are most effective when you are sitting well back and upright in the seat.
1. SRS curtain side-impact air bag mod- ules 2. SRS curtain side-impact air bag (driv- er’s side) 3. Seat belt buckle switches 4. Supplemental front air bag modules 5. Crash zone sensor 6. Diagnosis sensor unit 7. Occupant classification system control unit 8.
9. Seat belt pre-tensioner retractor 10. Satellite sensors 11. Supplemental side air bag modules (if so equipped) 12. SRS curtain side-impact air bag (pas- senger’s side) NISSAN Advanced Air Bag System (front seats) This vehicle is equipped with the NISSAN ad- vanced air bag system for the driver and front passenger seats.
The supplemental front air bags operate only when the ignition switch is in the ON or ST ART position. After turning the ignition key to the ON position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7 seconds if the system is operational.
The purpose of the regulation is to help reduce the risk of injury or death from an inflating air bag to certain front passenger seat occupants, such as children, by requiring the air bag to be auto- matically turned OFF . Certain sensors are used to meet the requirements.
passenger air bag status light is not illuminated (indicating that the air bag might inflate in a crash) , it could be that the child restraint or seat belt is not being used properly . In rare cases, the passenger air bag status light will not illuminate even though the air bag is OFF .
● Work on and around the supplemental front air bag system should be done by a NISSAN dealer. Installation of electri- cal equipment should also be done by a NISSAN dealer. The Supplemental Re- straint System (SRS) wiring should not be modified or disconnected.
The seat belts should be correctly worn and the driver and passenger seated upright as far as practical away from the supplemental side air bag. Rear seat passengers should be seated as far away as practical from the door finishers and side roof rails.
Pre-tensioner seat belt system (Front seats) WARNING ● The pre-tensioner seat belt cannot be reused after activation. It must be re- placed together with the retractor and buckle as a unit.
1. SRS Front Air Bag W arning Labels 2. SRS Side Air Bag W arning Label (if so equipped) SUPPLEMENTAL AIR BAG WARNING LABELS W arning labels about the supplemental front air bag and supplemental side air bag systems (if so equipped) are placed in the vehicle as shown in the illustration.
WARNING If the supplemental air bag warning light is on, it could mean that the supplemental front air bag, supplemental side air bag, curtain side-impact air bag systems and/or pre-tensioner seat belt systems will not operate in an accident.
Safety—Seats, seat belts and supplemental restraint system 1-67 MEMO.
2 Instruments and controls Instrument panel ...................................2 - 2 Meters and gauges ................................2 - 3 Speedometer and odometer .....................2 - 4 T achometer ....................................2 - 4 Engine coolant temperature gauge .
Cup holders .................................. 2-33 Cargo organizer (if so equipped) ................ 2-35 3rd row armrest bin ............................ 2-36 Cargo area storage bin ......................... 2-36 Garment hook .......................
1. V entilators (P . 4-31) 2. Headlight/fog light (if so equipped)/turn signal switch (P . 2-19) 3. Steering wheel switch for audio control/Bluetooth T hands-free phone system (if so equipped) (P . 4-59) 4. Driver supplemental air bag/horn (P . 1-51, P .
17. Shift selector lever (P . 5-10) 18. Ignition switch (P . 5-8) 19. Tilt steering wheel control (P . 3-21) 20. Rear sonar system off switch (if so equipped) (P . 2-26) 21. V ehicle dynamic control (VDC) off switch (if so equipped) or T raction con- trol system (T CS) off switch (if so equipped) (P .
SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates vehicle speed in miles per hour (MPH) and kilometers per hour (km/h) . Odometer/T win trip odometer The odometer/twin trip odometer is displayed when the ignition key is in the ON position.
ENGINE COOLANT TEMPERATURE GAUGE The gauge indicates the engine coolant tempera- ture. The engine coolant temperature is within the normal range s 1 when the gauge needle points within the zone shown in the illustration. The engine coolant temperature varies with the outside air temperature and driving conditions.
The indicates that the fuel-filler door is located on the driver’s side of the vehicle. CAUTION ● If the vehicle runs out of fuel, the malfunction indicator light (MIL) may come on. Refuel as soon as possible. After a few driving trips, the light should turn off.
or Anti-lock braking warning light Seat belt warning light and chime Front passenger air bag status light or Brake warning light Supplemental air bag warning light Security indicator light Charge warn.
W ARNING LIGHTS or Anti-lock braking warning light If the light comes on while the engine is running, it may indicate the anti-lock braking system is not functioning properly .
The engine oil pressure warning light is not designed to indicate a low oil level. Use the dipstick to check the oil level. See “Engine oil” in the “Maintenance and do-it-yourself” section of this manual. CAUTION Running the engine with the engine oil pressure warning light on could cause se- rious damage to the engine almost imme- diately.
If you select the tire pressure information in the display , the L OW PRESSURE warning message will be displayed. The tire pressure for each tire will also be displayed. Y our vehicle can be driven for a limited time on a flat tire. See “Michelin P AX Tires” in the “Mainte- nance and do-it-yourself” section.
CAUTION ● The TPMS is not a substitute for the regular tire pressure check. Be sure to check the tire pressure regularly. ● If the vehicle is being driven at speeds of less than 16 MPH (25 km/h) , the TPMS may not operate correctly. ● Be sure to install the specified size of tires to the 4 wheels correctly.
Cruise main switch indicator light The light comes on when the cruise control main switch is pushed. The light goes out when the main switch is pushed again. When the cruise main switch indicator light comes on, the cruise control system is operational.
– if possible, reduce the amount of cargo being hauled or towed. The malfunction indicator light may stop blinking and come on steady . Have the vehicle inspected by a NISSAN dealer.
V ehicle dynamic control off indicator light (if so equipped) This indicator light comes on when the vehicle dynamic control off switch is pushed to OFF . This indicates the vehicle dynamic control system is not operating. Push the vehicle dynamic control off switch again or restart the engine and the system will operate normally .
brief period. Never leave your keys in the ignition, and always lock the vehicle when unattended. Be aware of your surroundings, and park in secure, well-lit areas whenever possible.
NISSAN VEHICLE IMMOBILIZER SYSTEM The NISSAN V ehicle Immobilizer System will not allow the engine to start without the use of a registered key . If the engine fails to start using a registered key (f.
SWITCH OPERATION The windshield wiper and washer operates when the ignition switch is in the ON position. Push the lever down to operate the wiper at the following speed: s 1 Intermittent (INT) — intermittent operation can be adjusted by turning the knob toward s A (Slower) or s B (Faster) .
The rear window wiper and washer operate when the ignition switch is in the ON position. T urn the switch clockwise from the OFF position to operate the wiper. s 1 Intermittent (INT) – intermittent operation (not adjustable) s 2 ON – continuous low speed operation Push the switch forward s 3 to operate the washer.
HEADLIGHT CONTROL SWITCH Lighting s 1 When turning the switch to the posi- tion, the front parking, tail, license plate and instrument panel lights come on. s 2 When turning the switch to the posi- tion, the headlights come on and all the other lights remain on.
Autolight system (if so equipped) The autolight system allows the headlights to be set so they turn on and off automatically . The autolight system can: ● T urn on the headlights, front parking, tail, license plate and instrument panel lights au- tomatically when it is dark.
Be sure you do not put anything on top of the autolight sensor s 1 located on top of the instrument panel. The autolight sensor controls the autolight ; if it is covered, the autolight sensor reacts as if it is dark out and the headlights will illuminate.
WARNING When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.
T URN SIGNAL SWITCH T urn signal s 1 Move the lever up or down to signal the turning direction. When the turn is com- pleted, the turn signals cancel automatically . Lane change signal s 2 T o signal a lane change, move the lever up or down to the point where the indicator light begins to flash, but the lever does not latch.
CORNERING LIGHT The cornering light provides additional illumina- tion toward the turning direction. The cornering light will illuminate on the turning direction side when a turn is signaled with the headlights on. Push the switch on to warn other drivers when you must stop or park under emergency condi- tions.
T o sound the horn, push the center pad area of the steering wheel. WARNING Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system. T am- pering with the supplemental front air bag system may result in serious personal injury.
The vehicle should be driven with the T raction Con- trol System (T CS) on for most driving conditions. If the vehicle is stuck in mud or snow , the T CS reduces the engine output to reduce wheel spin. The engine speed will be reduced even if the accelerator is depressed to the floor.
The rear sonar system can be disabled by push- ing the OFF switch. When the system is disabled, the indicator light on the switch will illuminate. The system will automatically reset the next time the ignition switch is turned on. See “Rear sonar system” in the “Starting and driving” section.
● Before inserting or disconnecting a plug, be sure the electrical accessory being used is turned OFF . ● Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal temperature fuse may open. ● When not in use, be sure to close the cap.
CONSOLE BOX (if so equipped) Push the corresponding button s 1 to open the small storage compartments. Slide the console box cover s 2 back to access the large storage compartment. The CD/DVD tray is removable. Pull up on the lever to access the front storage bin on the console box.
CENTER TRAY TABLE (if so equipped) T o use the center tray table, raise it up until it locks into the upright position. T o access the small storage compartment on the top of the tray table, raise the lid. CAUTION T o avoid damaging it, do not apply a total load of more than 50 lbs (23 kg) to the center tray table.
GLOVE BOX Open the glove box by pulling the handle. Use the master key when locking s 1 or unlocking s 2 the glove box. The valet key cannot be used to lock or unlock the glove box. WARNING Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop.
SEATBACK POCKETS The seatback pockets are located on the back of the driver’s and passenger’s seats. The pockets can be used to store maps. GROCERY HOOKS The grocery hooks allow for standard size plastic grocery bags to hang side by side. CAUTION Do not apply a total load of more than 18 lbs (8 kg) to a single grocery hook.
OVERHEAD CONSOLE WARNING Keep storage bins closed while driving to help prevent injury in an accident or a sudden stop. Large storage bin Push the button to open the storage bin. Push the lid up to close. Small storage bin Push the button to open the small storage bin.
Front T ype B T o use the cup holders, raise the center tray table. Refer to “Center tray table” earlier in this section. 2nd row T ype A LIC0955 T ype B LIC0896 LIC0509 2-34 Instruments and contr.
3rd row Soft bottle holder CAUTION ● Do not use bottle holder for any other objects that could be thrown about in the vehicle and possibly injure people during sudden braking or an accident.
1. Move both front seats as forward as pos- sible. Refer to 9 Seats 9 in the 9 Safety – seats, seat belts and supplemental restraint sys- tem 9 section earlier in this manual. 2. Stow the center tray table (if so equipped) . Refer to “Center tray table” earlier in this section.
GARMENT HOOK T o store garments, pull the garment hook down to the use position. CAUTION Do not apply a total load of more than 55 lbs (25 kg) to the hook. HEAD RESTRAINT STORAGE The storage bag can be used to store up to three head restraints or other items.
WARNING Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, un- secured cargo could cause personal injury. CAUTION Use care when placing or removing items from the roof rack. If you cannot comfort- ably lift the items onto the roof rack from the ground, use a ladder or stool.
Driver’s side power window switch The driver’s side control panel is equipped with switches to open or close all of the windows. The power windows operate when the ignition switch is in the ON position, or for about 45 seconds after the ignition switch is turned to the OFF position.
Auto-reverse function The auto-reverse function can be activated when a window is closed by automatic operation. Depending on the environment or driving conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the window oc- curs.
MANUAL VENT WINDOWS (if so equipped) T o open a manual vent window, pull the latch handle toward you until it releases. T o lock the window in the open position, push the latch handle rearward until it locks.
T o open or close the sunroof part way, push the switch in any direction s 5 while the roof is sliding open or closed to stop it in the desired position. Tilting the sunroof T o tilt the sunroof up, push the tilt switch toward the up position s 1 . When the sunroof is open, it will automatically close and then tilt up.
If the sunroof does not close Have your NISSAN dealer check and repair the sunroof. The lights on demand switch allows the driver to select one of three lighting modes for the interior lights and puddle lamps (if so equipped) . The lights on demand switch operates regardless of ignition switch position.
NO TE: The footwell and door step lights illuminate when the driver and passenger doors are open regardless of the lights on demand switch position. These lights will turn off automatically after 30 minutes while doors are open to prevent the battery from be- coming discharged.
The cargo light on the overhead trim (T ype C) has a three-position switch. T o operate, push the light. On: The light is illuminated Normal: The light illuminates when any door is opened or unlocked by the keyfob. The light turns off after 30 seconds or when all doors are closed.
The HomeLink T Universal T ransceiver provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLink T Universal T ransceiver: ● Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and se- curity systems.
3. Using both hands, simultaneously press and hold both the HomeLink T button you want to program and the hand-held transmitter but- ton. DO NO T release the buttons until step 4 has been completed. 4. Hold down both buttons until the indicator light on the HomeLink T flashes, changing from a “slow blink” to a “rapidly flashing blink” .
PROGRAMMING HOMELINK T FOR CANADIAN CUSTOMERS Prior to 1992, D.O.C. regulations required hand- held transmitters to stop transmitting after 2 sec- onds.
that was just programmed. This procedure will not affect any other programmed HomeLink T buttons. IF YOUR VEHICLE IS STOLEN If your vehicle is stolen, you should change the codes of any non-rolling code device that has been programmed into HomeLink T .
2-50 Instruments and controls MEMO.
3 Pre-driving checks and adjustments K e y s .............................................3 - 2 Nissan vehicle immobilizer system keys ...........3 - 2 Doors ............................................3 - 3 Locking with key ..........................
1. T wo master keys (black) with transpon- der chip and chrome NISSAN brand symbol on one side 2. V alet key (black) with transponder chip 3. K ey number plate 4. T ransponder chip A key number plate is supplied with your keys. Record the key number and keep it in a safe place (such as your wallet) , not in the vehicle.
WARNING ● Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally open- ing the doors, and will help keep out intruders.
Opening and closing windows The driver’s door key operation allows you to open and close windows equipped with auto- matic operation at the same time. ● T o open the windows, turn the driver’s door key toward the rear of the vehicle for longer than 1 second after the door is unlocked.
LOCKING WITH POWER DOOR LOCK SWITCH T o lock all the doors without a key, push the door lock switch (driver’s or front passenger’s side) , to the lock position s 1 . When locking the door this way , be certain not to leave the key inside the vehicle.
USING THE MAIN ON/OFF SWITCH FOR THE POWER SLIDING DOOR (if so equipped) The main ON/OFF switch is located in the over- head console. Push the switch ON to enable the door pillar switches and the power assist feature. An indica- tor light will illuminate when the switch is in the ON position.
or close position using the inside or outside handle, the power assist feature will be activated and the door will complete its motion automati- cally . Power Open: The door automatically moves from the fully closed position to the fully open position in ap- proximatel y3–6 seconds.
Clutch Mode: T o help prevent unexpected slams due to gravity, the clutch mode is engaged intermittently for approximatel y5–8 seconds when power open or close is interrupted due to multiple obstacles, low battery voltage or the main ON/OFF switch turned to OFF .
CHILD SAFETY SLIDING DOOR LOCK The child safety lock helps prevent the sliding door from being opened accidentally , especially when small children are in the vehicle.
CAUTION Listed below are conditions or occur- rences which will damage the keyfob: ● Do not allow the keyfob to become wet. ● Do not drop the keyfob. ● Do not strike the keyfob sharply against another object. ● Do not place the keyfob for an extended period in an area where temperatures exceed 140°F (60°C) .
Unlocking doors Push the button on the keyfob once. ● Only the driver’s door unlocks. ● The hazard indicator flashes once if all doors are completely closed with the ignition key in any position except the ON position.
Operating the power sliding door (if so equipped) Push and hold the button on the keyfob for about 0.5 second to open or close the power sliding door. The door will reverse direction immediately dur- ing power open or power close if the keyfob button is pressed.
Silencing the horn beep feature If desired, the horn beep feature can be deacti- vated using the keyfob. NO TE: If you use the keyfob to change the horn beep and lamp flash feature for vehicles with color screen, the display will not show the current mode and cannot be used to change the mode.
s 1 Pull the hood lock release handle located below the driver’s side instrument panel. The hood will spring up slightly . s 2 Push the lever at the front of the hood to the side as illustrated with your fingertips and raise the hood. s 3 Insert the support rod into the slot on the underside of the hood.
OPERATING THE MANUAL LIFT GATE The power door lock system allows you to lock or unlock all doors including the lift gate simulta- neously . T o open the lift gate, depress the opener handle and lift up. T o close, lower and push the lift gate down se- curely .
OPERATING THE POWER LIFT GATE (if so equipped) NO TE: T o open, close or reverse the power lift gate, the shift selector lever must be in P (Park) . Also, the power lift gate will not operate if battery voltage is low.
Reverse: The power lift gate will reverse direction immedi- ately during power open or power close if the keyfob, overhead console or rear pillar switch is pressed.
CAUTION ● If the power lift gate does not stay open or if the lift gate unexpectedly closes at any time while a continuous warning chime sounds, do not operate the lift gate. There may be a pressure loss in one or both of the lift gate gas stays. Have the lift gate inspected by a NISSAN dealer.
P ower lift gate (if so equipped) If the lift gate cannot be opened with the door lock switch or keyfob due to a discharged battery , follow these steps: 1. Remove the cover on the inside of the lift gate. 2. Move the lever up to open the lift gate. OPENER OPERATION The fuel-filler door release is located on the driv- er’s door.
WARNING ● Gasoline is extremely flammable and highly explosive under certain condi- tions. Y ou could be burned or seriously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling.
TILT OPERATION Pull the lock lever forward and adjust the steering wheel up or down to the desired position. Push the lock lever back to lock the steering wheel in place. WARNING Do not adjust the steering wheel while driving. Y ou could lose control of your vehicle and cause an accident.
s 1 T o block glare from the front, swing down the main sun visor. s 2 T o block glare from the side, remove the main sun visor from the center mount and swing the visor to the side. s 3 Slide the sun visor in or out as needed. V ANITY MIRRORS T o access the vanity mirror, pull the sun visor down and flip open the mirror cover.
REARVIEW MIRROR (if so equipped) The night position s 1 reduces glare from the headlights of vehicles behind you at night. Use the day position s 2 when driving in daylight hours. WARNING Use the night position only when neces- sary, because it reduces rear view clarity.
OUTSIDE MIRRORS WARNING Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mirror or glance over your shoulder to properly judge distances to other objects.
Foldable outside mirrors Push the mirrors backward to fold them. Reverse tilt-down feature (if so equipped) The reverse tilt-down feature will turn the se- lected outside mirror surface downward to pro- vide better rear visibility close to the vehicle.
MEMORY STORAGE FUNCTION T wo positions for the driver’s seat, accelerator and brake pedals, and outside mirrors can be stored in the automatic drive positioner memory . Follow these procedures to use the memory sys- tem. 1. Set the automatic transmission selector le- ver to the P (Park) position.
3. Push the memory switch 1 or 2 fully for at least 1 second to operate the automatic drive positioner. 4. T urn the outside mirror control switch to L (left) . 5. Depress the brake pedal. 6. Move the automatic transmission shift lever to R (Reverse) .
● When the key is turned from ACC to L OCK with the driver’s door open. The driver’s seat will return to previous position: ● When the key is inserted into the ignition switch and the driver’s door is closed. ● When the driver’s door is closed with the key turned to L OCK.
Pre-driving checks and adjustments 3-29 MEMO.
4 Display screen, heater, air conditioner, audio and phone systems Control panel buttons — with monochrome screen ....4 - 2 How to use the TRIP button .....................4 - 3 How to use the SETTING button .................4 - 5 button ...........
CD care and cleaning .......................... 4-58 Steering wheel switch for audio control .......... 4-59 Rear audio controls (if so equipped) ............. 4-60 Antenna ...................................... 4-61 DVD entertainment system (if so equipped) .
WARNING ● Do not disassemble or modify this sys- tem. If you do, it may result in accidents, fire, or electrical shock. ● Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound. Continued use of the system may result in accident, fire or electric shock.
Reference symbols: TRIP button — This is a button on the control panel. By pressing this button you can select the item or perform this action. HOW TO USE THE TRIP BUTTON When the TRIP button is pressed, the following modes will display on the screen.
Average speed (MPH or km/h) The Average Speed mode shows the average speed since the last reset. T o calculate the aver- age speed, driving distance is divided by driving time. For approximately the first 30 seconds after a reset or reconnecting the battery cables, the display will show (*) .
In case of low tire pressure, a message “L OW PRESSURE” or “CHECK ALL TIRES” is dis- played on the screen: L OW PRESSURE — CHECK ALL TIRES. WARNING ● When a spare tire is mounted or a whee.
Language The language can be changed to “ENGLISH” or “FRANÇAIS” by pressing the TUNE button. MP3 display type (if so equipped) T o change how MP3 discs are displayed, press the TUNE button to select “DISC NUMBER” or “FOLDER NUMBER” . Disc number mode will display the file number in the disc.
1. TRIP button (P . 4-8) 2. BACK (previous) button (P . 4-7) 3. Joystick and ENTER button (P . 4-7) 4. brightness control button (P . 4-16) 5. SETTING button (P . 4-11) If you use the system with the engine not running (ignition ON or ACC) for a long time, it will use up all the battery power, and the engine will not start.
HOW TO USE THE TRIP BUTTON When the TRIP button is pressed, the following modes will display on the screen. W arning message (if any) → TRIP 1 → TRIP 2 → FUEL ECONOMY → MAINTENANCE → Audio o.
Resetting fuel economy The average fuel economy calculation can be reset to 0. Press the TRIP button repeatedly until the FUEL ECONOMY menu is shown, then ei- ther: ● Select the “Reset” key on screen by press- ing the ENTER button, or ● Press the TRIP button for more than approxi- mately 1.
Resetting the maintenance interval The ENGINE OIL and TIRE RO T A TION mainte- nance intervals can be reset to 0 miles (kilome- ters) . Select the “Reset” key using the joystick and press the ENTER button.
Tire pressure information T o display tire pressure information, press the TRIP button repeatedly until the MAINTENANCE screen is displayed. Select the “Tire Pressure” key using the joystick and press the ENTER but- ton. Pressure indication in ** psi on the screen indi- cates that the pressure is being measured.
Display settings Select the “Display” key and press the ENTER button. The DISPLA Y SETTINGS screen will ap- pear. Brightness/contrast/screen background: Select the “Brightness/Contrast/Screen Back - ground” key to adjust the brightness and contrast of the screen.
T o turn the screen on, ● Press the SETTING button and select the “Display” key and then select the “Display Off” key. Then set the screen to on by press- ing the ENTER button, or ● Hold t.
V ehicle electronic systems Select the “V ehicle Electronic Systems” key by using the joystick and pressing the ENTER but- ton. The VEHICLE ELECTRONIC S Y STEMS screen will be displayed. Y ou can set the following operating conditions by selecting the desired item using the joystick, then pressing the ENTER button.
Adjust driver seat when exiting vehicle: Se- lect so the driver’s seat automatically moves back and returns to the original position for ease of exit and entry .
Y ou can select the language and unit using the joystick or pressing the ENTER button. The settings are automatically saved when you exit the menu by pressing the BACK button or any other mode button. Clock Adjusting the time: Select the “Hours” or “Minutes” key and move the joystick to the right or left to adjust the time.
1. ROUTE button* 2. DEST button* 3. MAP button* 4. BACK (previous) button (P . 4-18) 5. zoom out button* 6. Joystick and ENTER button (P . 4-17) 7. zoom in button* 8. VOICE button* 9. SETTING button (P . 4-22) 10. brightness control button (P . 4-28) 11.
HOW TO USE THE BACK BUTTON This button has two functions. ● Go back to the previous display (cancel) . If you press the BACK button during setup, the setup will be canceled and/or the display will return to the previous screen. ● Finish setup. In some screens pressing the BACK button ac- cepts the changes made during setup.
Fuel economy Press the TRIP button to display Average Fuel Economy and Distance T o Empty. Average fuel economy (MPG or L/100 km) The Average Fuel Economy is calculated based on fuel consumption since the last reset. The display is updated every 30 seconds and 1/3 mile (500 m) .
Changing the maintenance interval Select the “Engine Oil” or “Tire Rotation” key using the joystick and press the ENTER button to display the screen to change the maintenance interval. Select the “Maintenance Schedule” key using the joystick and move the joystick to right or left to set the maintenance interval.
● The ignition key is turned ON the next time the vehicle will be driven. T o return to the previous display after the MAIN- TENANCE NO TICE screen is displayed, press the BACK button. The MAINTENANCE NO TICE screen displays each time the key is turned ON until one of the following conditions are met: ● “Reset” key is selected.
HOW TO USE THE SETTING BUTTON When the SETTING button is pressed, the SET - TINGS screen will appear on the display . Y ou can select and/or adjust several functions, features and modes that are available for your vehicle. Move the joystick and press the ENTER button to select each item to be set.
Display off: Select the “Display Off” key. The indicator of the “Display Off” turns amber and the message above will be displayed briefly . When the audio, HV AC (Heater and air conditioner) , or any mode button on the control panel is operated, the dis- play turns on for that operation.
Any time audio information is shown on the main part of the screen, HV AC information will be displayed on the lower part of the screen. HV AC information will be shown even if “ Audio” is se- lected to be displayed on the lower part of the screen.
Adjust driver seat when exiting vehicle: Se- lect so the driver’s seat automatically moves back and returns to the original position for ease of exit and entry .
Automatic headlights off delay: Select to change the setting for the length of time the automatic headlights remain on after exiting the vehicle. Speed dependent wiper: Select to turn on or turn off the driving speed dependent intermittent wiper function.
Clock Adjusting the time: Select the “Hours” or “Minutes” key and move the joystick to the right or left to adjust the time. The time will change step by step. The new settings are automatically saved when you exit the setting screen by pressing the BACK button or any other mode button.
Selecting the time zone: 1. Select the “Select Time Zone” key. The TIME Z ONE screen will appear. 2. Select one of the following zones, depend- ing on the current location. ● Pacific zone ● Mountain zone ● Central zone ● Eastern zone ● Atlantic zone ● Newfoundland zone After selection, the CL OCK SETTINGS screen will appear.
When the selector lever is shifted into the R (Reverse) position, the monitor display shows view to the rear of the vehicle. WARNING ● The system is designed as an aid to the driver in detecting large stationary ob- jects to help avoid damaging the ve- hicle.
ADJUSTING THE SCREEN T o adjust the quality of the screen, refer to “HOW T O USE THE SETTING BUTTON” in this section. ● When it is difficult to see in the rearward direction due to shady conditions, press the ENTER button to make objects in the moni- tor brighter.
Adjust air flow direction for the driver and pas- senger side s 1 , center s 2 , and rear passenger s 3 ventilators by moving the ventilator slide and/or ventilator assemblies. WARNING ● The air conditioner cooling function op- erates only when the engine is running.
1. Fan speed control dial 2. Air conditioner button 3. Front window defrost/defog button 4. Rear window defroster switch 5. Air recirculation button 6. T emperature control dial 7. Air flow control buttons CONTROLS Fan control dial The fan control dial turns the fan on and off, and controls fan speed.
Air conditioner button Start the engine, turn the fan control dial to the desired position and push the button to turn on the air conditioner. A/C will appear on the display when the air conditioner is operating. T o turn off the air conditioner, push the button again, the display will show A/C OFF .
Heating and defogging This mode heats the interior and defogs the wind- shield. 1. Press the air flow control button. 2. T urn the fan control dial to the desired posi- tion. 3. T urn the temperature control dial to the de- sired position between the middle and the hot position.
● If the engine coolant temperature gauge indicates engine coolant tem- perature over the normal range, turn the air conditioner off. See “If your vehicle overheats” in the “In case of emergency” section of this manual.
WHA0645 WHA0646 4-36 Display screen, heater, air conditioner, audio and phone systems Z REVIEW COPY— 2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X.
WHA0647 WHA0648 Display screen, heater, air conditioner, audio and phone systems 4-37 Z REVIEW COPY— 2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X.
WHA0649 4-38 Display screen, heater, air conditioner, audio and phone systems Z REVIEW COPY— 2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X.
WHA0650 Display screen, heater, air conditioner, audio and phone systems 4-39 Z REVIEW COPY— 2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X.
1. Driver temperature control dial/AUT O button 2. A/C ON/OFF button 3. Fan speed control (decrease) 4. Front window defroster button 5. System off button 6. Rear window defroster button 7. Fan speed control (increase) 8. Air recirculation button 9. Passenger temperature control dial/ DUAL button 10.
● The temperature of the passenger compart- ment will be maintained automatically . Air flow distribution, fan speed and A/C on/off are also controlled automatically . ● A visible mist may be seen coming from the vents in hot, humid conditions as the air is cooled rapidly .
The sunload sensor s 1 , located on the top center of the instrument panel, helps the system main- tain a constant temperature. Do not put anything on or around this sensor. Rear seat temperature and fan speed can be controlled from both the front seat overhead con- sole controls s A or the rear seat overhead con- sole controls s B .
CONTROLS Fan control dial The fan control dial turns the rear vent fan on and off, and controls fan speed. T emperature control dial The temperature control dial allows rear passen- gers to adjust the temperature of the outlet air.
Reception conditions will constantly change be- cause of vehicle movement. Buildings, terrain, signal distance and interference from other ve- hicles can work against ideal reception. De- scribed below are some of the factors that can affect your radio reception.
AUDIO OPERATION PRECAUTIONS Compact disc (CD) player CAUTION ● Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD changer/player. ● T rying to load a CD with the CD door closed could damage the CD and/or CD changer.
● If the CD cannot be played, one of the following messages will be displayed. CHECK DISC: ● Confirm that the CD is inserted cor- rectly (the label side is facing up, etc .) . ● Confirm that the CD is not bent or warped and it is free of scratches.
● If there is a file in the top level of the disc, “ROO T” is displayed. ● The playback order is the order in which the files were written by the writing software.
T roubleshooting guide: Symptom Cause and Countermeasure Cannot play Check if the disc was inserted correctly. Check if the disc is scratched or dirty. Check if there is condensation inside the player. If there is, wait until the condensation is gone (about 1 hour) before using the player.
1. SEEK/TRACK button 2. PRESET A·B·C button 3. CD/DVD button 4. Station select (1 - 6) buttons 5. POWER/VOLUME control knob 6. REAR CTRL button 7. AUX button 8. TUNE/CA T button 9. DISP button 10. FM·AM/SA T (satellite) radio button* 11. SCAN/RPT button 12.
1. SEEK/TRACK button 2. PRESET A·B·C button 3. CD/DVD button 4. Station and CD select (1 - 6) buttons 5. POWER/VOLUME control knob 6. REAR CTRL button 7. AUX button 8. TUNE/FLDR·CA T button 9. DISP button 10. FM·AM/SA T (satellite) radio button* 11.
1. SEEK/TRACK button 2. PRESET A·B·C button 3. CD/DVD button 4. Station and CD select (1 - 6) buttons 5. POWER/VOLUME control knob 6. REAR CTRL button 7. AUX button 8. TUNE/FLDR·CA T button 9. DISP button 10. SCAN button 11. FM·AM/SA T (satellite) radio select but- ton* 12.
No satellite radio reception is available and “NO SA T” is displayed when the SA T button is pressed unless optional satellite receiver and antenna are installed, and an XM T or SIRIUS™ satellite radio service subscription is active. Sat- ellite radio not available in Alaska, Hawaii and Guam.
Once a display mode is selected, press the AU- DIO button again to store the setting. ● Folder number mode displays the folder number and the file number of the folder currently being played. ● Disc number mode displays the number se- lected disc and the track that is currently being played.
The FM stereo indicator ST will glow during FM stereo reception. When the stereo broadcast signal is weak, the radio will automatically change from stereo to monaural reception. TUNE (T uning T ype A only) : T o manually tune the radio, press the TUNE button or .
Compact disc (CD) player operation (T ype A) T urn the ignition key to the ACC or ON position and insert the compact disc into the slot with the label side facing up. The compact disc will be guided automatically into the slot and start play- ing. If the radio is already operating, it will automati- cally turn off and the compact disc will play .
(SPEAKER CONTROL) button: Press this button to turn the rear speakers off and headphones on. Press this button again to turn rear seat speakers back on and headphones off. CD EJECT: When the button is pressed with the com- pact disc loaded, the compact disc will be ejected.
CD select buttons: T o play another CD that has been loaded, press a CD select button (1 – 6) . RPT•RDM button (T ype C only) : When the RPT•RDM button is pressed while the compact disc is playe.
CD CARE AND CLEANING ● Handle a CD by its edges. Do not bend the disc. Never touch the surface of the disc. ● Always place the discs in the storage case when they are not being used. ● T o clean a disc, wipe the surface from the center to the outer edge using a clean, soft cloth.
1. V olume control switch 2. Phone operation switch 3. POWER on and MODE select switch 4. T uning switch STEERING WHEEL SWITCH FOR AUDIO CONTROL The audio system can be operated using the controls on the steering wheel.
1. VOL (volume) control button 2. MODE select button 3. speaker control button 4. NEXT button 5. SEEK button 6. Headphone jacks 7. Infrared headphone transmitter lens* *Red transmitters will be visible when infrared headphones are on.
VOL (volume) button: The VOL button allows the rear passengers to adjust the headphone volume level. (SPEAKER CONTROL) button: Press this button to turn the rear speakers off and headphones on. Press this button again to turn rear seat speakers back on and headphones off.
WARNING ● The DVD Entertainment System is de- signed for rear seat passenger viewing only. ● The driver must not attempt to operate the DVD Entertainment System while the vehicle is in motion so that full at- tention may be given to vehicle operation.
1. EJECT button 2. DVD slot 3. ENTER button 4. POWER on/off button 5. MODE button 6. Input jacks 7. ST OP button 8. PLA Y/P AUSE button 9. MENU button 10. DISPLA Y button 11. NA VIGA TION keys DIGITAL VIDEO DISC (DVD) PLAYER CONTROLS Refer to “Playing a digital video disc (DVD)” later in this section for the function of each button.
6. DISPLA Y button 7. MODE button 8. SUBTITLE button 9. AUDIO button 10. ANGLE button 11. CLEAR button 12. P AUSE button 13. PLA Y button 14. F AST FORW ARD/F AST REVERSE button 15.
Headphones Power ON/OFF: Press the power button to turn the headphones on or off. V olume control: T urn the volume control knob to adjust the vol- ume. The headphones will automatically be turned off in 30 seconds if there is no sound during that period.
Pressing the button on the front controls turns the rear speakers on and off. It is possible to operate the DVD player by remote control. Headphones are a wireless type and no cables are necessary . Y ou can use them in almost all the ranges in the rear seat.
If the ST OP button is pressed again when the player is already in Stop mode, it will reinitialize the pointer to the beginning of the disc. In effect it will ignore the last stored disc position and upon receipt of the next play message it will begin at the Title Menu, or at “the beginning of the disc” .
TITLE (Remote control only) : Press TITLE button to return the DVD media to the “title” of the DVD. Press TITLE button again to return to the previous stop point and play . BACK (Remote control only) : Press the BACK button to exit the current active menu and return to the previous menu.
● Do not attempt to use the system in extreme temperature conditions [below -4°F (-20°C) or above 158°F (70°C)]. ● Do not attempt to operate the system in extreme humidity conditions (less than 10% or more than 75%) . HOW TO HANDLE THE DVD CAUTION ● Handle a DVD by its edges.
DVD player operation precautions Do not use the following DVDs as they may cause the DVD player to malfunction: ● 3.1 in (8 cm) disc s with an adapter ● DVDs with a region code other than “1” .
Remote control and headphones battery replacement Replace the battery as follows: 1. Open the lid. 2. Replace batteries with new ones. ● Size AA (remote control) ● Size AAA (headphones) Make sure that the and ends on the batteries match the markings inside the compartment.
When installing a CB, ham radio or car phone in your NISSAN, be sure to observe the following precautions, otherwise the new equipment may adversely affect the engine control system and other electronic parts. WARNING ● A cellular telephone should not be used while driving so full attention may be given to vehicle operation.
Y our NISSAN is equipped with the Bluetooth T Hands-Free Phone System. If you are an owner of a Bluetooth T enabled cellular phone, you can set up the wireless connection between your cellular phone and the in-vehicle phone module.
– Y our cellular phone is locked to prevent it from being dialed. When the radio wave condition is not ideal or ambient sound is too loud, it may be difficult to hear the other person’s voice during a call.
● If you need to hear the available commands for the current menu again, say “Help” and the system will repeat them. ● If a command is not recognized, the system announces, “Command not recognized. Please try again.” Repeat the command in a clear voice.
CONTROL BUTTONS The control buttons for the Bluetooth T Hands- Free Phone System are located on the steering wheel. PHONE/SEND Press the button to initiate a VR session or answer an incoming call. Y ou can also use the button to skip through system feedback and to enter commands during a call.
Pairing procedure NO TE: The pairing procedure must be performed when the vehicle is stationary. If the vehicle starts moving during the procedure, the procedure will be cancelled. Main Menu “Setup” s A “Pair Phone” s B “New Phone” s C Initiate from handset s D Name phone s E Assign priority s F Choose ringtone s G 1.
3. Say the number you wish to call s B . For example, 555-1212 can be said as “five five five one two one two.” See “How to say numbers” earlier in this section for more information. 4. When you have finished speaking the phone number, the system repeats it back and an- nounces the available commands.
When prompted by the system, say the name of the phone book entry you wish to call. The system acknowledges the name. If there are multiple locations associated with the name, the system asks you to choose the loca- tion. Once you have confirmed the name and location, the system begins the call.
“Phone book” NO TE: Phone book commands are not available when the vehicle is moving. Main Menu “Phone Book” “New Entry” s A “Edit” s B “Delete” s C 9 List Names” s D The Phone Book stores up to 40 names for each phone paired with the system.
T o delete entries from the phone book, say a name or “ All entries” when prompted by the sys- tem. The system acknowledges the command and asks you to confirm the deletion. T o delete the current redial number or call back number, say “redial number” or “call back num- ber” when prompted by the system.
NO TE: The pairing procedure must be performed when the vehicle is stationary. If the vehicle starts moving during the procedure, the procedure will be cancelled. Also, see “Pairing procedure” earlier in this section for additional information. Up to 5 phones can be paired.
NO TE: When you delete a phone, the associated phone book for that phone will also be deleted. “Select ringtone” s F Use the Select Ringtone command to select the tone heard in the vehicle when an incoming call is received.
11. The system will announce that speaker ad- aptation has been completed and the sys- tem is ready . The SA mode will stop if: ● The button is pressed for more than 5 seconds in SA mode. ● The vehicle begins moving during SA mode. ● The ignition switch is turned to the OFF or L OCK position.
Symptom Solution System fails to interpret the command correctly. 1. Ensure that the command is valid. See “List of voice commands” earlier in this section. 2. Ensure that the command is spoken after the tone. 3. Speak clearly without pausing between words and at a level appropriate to the ambient noise level in the vehicle.
4-86 Display screen, heater, air conditioner, audio and phone systems MEMO.
5 Starting and driving Precautions when starting and driving ................5 - 2 Exhaust gas (carbon monoxide) ..................5 - 2 Three-way catalyst ..............................5 - 2 Tire pressure monitoring system (TPMS) (for models without Michelin T PA X T tires only) .
WARNING ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle.
CAUTION ● Do not use leaded gasoline. Deposits from leaded gasoline will seriously re- duce the three-way catalyst’s ability to help reduce exhaust pollutants. ● Keep your engine tuned up. Malfunc- tions in the ignition, fuel injection, or electrical systems can cause overrich fuel flow into the three-way catalyst, causing it to overheat.
● The TPMS will activate only when the vehicle is driven at speeds above 16 MPH (25 km/h) . Also, this system may not detect a sudden drop in tire pressure (for example a flat tire while driving) . ● Tire pressure rises and falls depending on the heat caused by the vehicle’s operation and the outside temperature.
TIRE PRESSURE MONITORING SYSTEM (TPMS) (for models with Michelin T PA X T tires only) Each tire, including the spare (if provided) , should be checked monthly when cold and in- flated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.
● Y ou can also check the pressure of all tires (except the spare tire) on the display screen. The order of the tire pressure figures dis- played on the screen does not correspond with the actual order of the tire position. See “Tire pressure information” in the “Display screen, heater, air conditioner and audio systems” section.
CAUTION Do not place metalized film or any metal parts (antenna, etc .) on the windows. This may cause poor reception of the signals from the tire pressure sensors, and the TPMS will not function properly.
WARNING Never remove or turn the key to the LOCK position while driving. The steering wheel will lock. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury.
K EY POSITIONS L OCK: Normal parking position (0) OFF: (Not used) (1) ACC: (Accessories) (2) This position activates electrical accessories such as the radio when the engine is not running. ON: Normal operating position (3) This position turns on the ignition system and the electrical accessories.
1. Apply the parking brake. 2. Move the shift selector lever to P (Park) or N (Neutral) . P (Park) is recommended. The shift selector lever cannot be moved out of P (Park) and into any of the other gear positions if the ignition key is turned to the OFF position or if the key is removed from the ignition switch.
The recommended operating procedures for this transmission are shown on the following pages. Follow these procedures for maximum vehicle performance and driving enjoyment. Starting the vehicle 1. After starting the engine, fully depress the foot brake pedal before attempting to move the shift selector lever out of the P (Park) position.
P (Park) : Use this selector position when the vehicle is parked or when starting the engine. Make sure the vehicle is completely stopped. The brake pedal must be depressed to move the se- lector lever from the N (Neutral) or any drive position to P (Park) .
T o push the shift lock release, complete the fol- lowing procedure: 1. T urn the ignition key to the LOCK position and remove the key 2. Apply the parking brake. 3. Remove the shift lock release cover as shown. 4. Insert a small screwdriver in the shift lock release slot and push down.
OFF: For driving up and down long slopes where engine braking is nec- essary push the Overdrive switch once. The O/D OFF indicator light in the instrument panel comes on at this time. When cruising at a low speed or climbing a gentle slope, you may feel uncomfortable shift shocks as the transmission shifts into and out of Overdrive repeatedly .
1. ACCEL/RES switch 2. COAST/SET switch 3. CANCEL switch 4. ON·OFF switch PRECAUTIONS ON CRUISE CONTROL ● If the cruise control system malfunctions, it cancels automatically . The SET indicator light in the instrument panel then blinks to warn the driver.
● the vehicle slows down more than 8 MPH (13 km/h) below the set speed. ● you move the shift selector lever to N (Neu- tral) . T o reset at a faster cruising speed, use one of the following three methods. ● Depress the accelerator pedal. When the vehicle attains the desired speed, push and release the COAST/SET switch.
● Accelerate slowly and smoothly . Maintain cruising speeds with a constant accelerator position. ● Drive at moderate speeds on the highway . Driving at high speed lowers fuel economy . ● Avoid unnecessary stopping and braking. Maintain a safe distance behind other ve- hicles.
WARNING ● Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire. ● Safe parking procedures require that both the parking brake be set and the transmission placed into P (Park) .
The power assisted steering uses a hydraulic pump, driven by the engine, to assist steering. If the engine stops or the drive belt breaks, you will still have control of the vehicle. However, much greater steering effort is needed, especially in sharp turns and at low speeds.
This procedure is described in the vehicle service manual and can be performed by a NISSAN dealer. ANTI-LOCK BRAKING SYSTEM (ABS) The anti-lock braking system controls the brakes so the wheels do not lock when braking abruptly or when braking on slippery surfaces.
● When installing a spare tire, make sure it is the proper size and type as speci- fied on the Tire and Loading Informa- tion label. For tire placard location in- formation, refer to “Tire and Loading Information label” in the “T echnical and consumer information” section of this manual.
When accelerating on slippery surfaces the tire may spin or slip. With the vehicle traction control system (T CS) , sensors detect these movements and control the braking and engine output to help improve vehicle stability while accelerating. ● When the traction control system is operat- ing, the slip indicator in the instrument panel blinks.
When accelerating or driving on slippery sur- faces, the tires may spin or slide. With the V ehicle Dynamic Control (VDC) system, sensors detect these movements and control the braking and engine output to help improve vehicle stability .
● If wheels or tires other than the recom- mended ones are used, the vehicle dy- namic control system may not operate properly and the vehicle dynamic con- trol off indicator light may come on. ● The vehicle dynamic control system is not a substitute for winter tires or tire chains on a snow covered road.
will sound for only three seconds. Once the sys- tem detects an object approaching, the tone will sound again. The RSS automatically turns on when the gear selector is placed in R (Reverse) and the ignition is ON. The RSS OFF switch on the instrument panel allows the driver to turn the RSS on and off.
3. Tire chains may be used. For details see “Tire chains” in the “Maintenance and do-it- yourself” section of this manual. TIRE EQUIPMENT 1. SUMMER tires have a tread designed to provide superior performance on dry pave- ment. However, the performance of these tires will be substantially reduced in snowy and icy conditions.
6 In case of emergency Flat tire ...........................................6 - 2 Tire pressure monitoring system (TPMS) ..........6 - 2 Changing a flat tire .............................6 - 3 Jump starting .....................................6 - 8 Push starting .
For vehicles equipped with Michelin T PA X T tires, the vehicle can be driven for a limited time on a flat tire, see 9 Michelin P AX Tires 9 in the 9 Mainte- nance and do-it-yourself 9 section. TIRE PRESSURE MONITORING SYSTEM (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS) .
CHANGING A FLAT TIRE If you have a flat tire, follow the instructions be- low . Stopping the vehicle 1. Safely move the vehicle off the road and away from traffic. 2. T urn on the hazard warning flashers. 3. Park on a level surface and apply the parking brake.
Getting the spare tire and tools 1. Tip up the passenger side second row cap- tain’s chair. Refer to “Tip up for easy entry to 3rd row” in the “Safety — seats, seat belts and supplemental restraint system” section of this owner’s manual.
Jacking up vehicle and removing the damaged tire WARNING ● Never get under the vehicle while it is supported only by the jack. If it is nec- essary to work under the vehicle, sup- port it with safety stands. ● Use only the jack provided with your vehicle to lift the vehicle.
Always refer to the proper illustrations for the correct placement and jack -up points for your specific vehicle model and jack type. Carefully read the caution label attached to the jack body and the following instruc- tions. 1. Loosen each wheel nut one or two turns by turning counterclockwise with the wheel nut wrench.
4. Lower the vehicle slowly until the tire touches the ground. Then, with the wheel nut wrench, tighten the wheel nuts securely in the sequence illustrated ( s A , s B , s C , s D , s E ) . Lower the vehicle completely. WARNING ● Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose or come off.
T o start your engine with a booster battery, the instructions and precautions below must be fol- lowed. WARNING ● If done incorrectly, jump starting can lead to a battery explosion, resulting in severe injury or death. It could also damage your vehicle.
WARNING Always follow the instructions below. Failure to do so could result in damage to the charging system and cause personal injury. 1. If the booster battery is in another vehicle, position the two vehicles to bring their bat- teries near each other.
CAUTION Automatic transmission models cannot be push-started or tow-started. Attempt- ing to do so may cause transmission damage. If your vehicle is overheating (indicated by an extremely high temperature gauge reading) , or if you feel a lack of engine power, detect abnormal noise, etc.
6. After the engine cools down, check the cool- ant level in the engine coolant reservoir tank with the engine running. Add coolant to the engine coolant reservoir tank if necessary . Have your vehicle repaired at a NISSAN dealer. When towing your vehicle, all State (Provincial in Canada) and local regulations for towing must be followed.
T OWING RECOMMENDED BY NISSAN NISSAN recommends that your vehicle be towed with the driving (front) wheels off the ground or place the vehicle on a flat bed truck as illustrated.
V EHICLE RECOVERY (freeing a stuck vehicle) Front WARNING ● Stand clear of a stuck vehicle. ● Do not spin your tires at high speed. This could cause them to explode and result in serious injury. Parts of your vehicle could also overheat and be damaged.
6-14 In case of emergency MEMO.
7 Appearance and care Cleaning exterior ..................................7 - 2 W ashing ......................................7 - 2 W axing ........................................7 - 2 Removing spots ................................7 - 2 Underbody .
In order to maintain the appearance of your ve- hicle, it is important to take proper care of it. T o protect the paint surfaces, please wash your vehicle as soon as you can: ● after a rainfall to prevent possible damage from acid rain. ● after driving on coastal roads.
UNDERBODY In areas where road salt is used in winter, it is necessary to clean the underbody regularly in order to prevent dirt and salt from building up and causing the acceleration of corrosion on the un- derbody and suspension. Before the winter pe- riod and again in the spring, the underseal must be checked and, if necessary , retreated.
Occasionally remove loose dust from the interior trim, plastic parts and seats using a vacuum cleaner or soft bristled brush. Wipe the vinyl and leather surfaces with a clean, soft cloth damp- ened in mild soap solution, then wipe clean with a dry , soft cloth.
SEAT BELTS The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solution. Allow the belts to dry completely in the shade before using them. See “Seat belt maintenance” in the “Safety – Seats, seat belts and supplemen- tal restraint system” section of this manual.
● Never allow water or other liquids to come in contact with electronic compo- nents inside the vehicle as this may damage them. Chemicals used for road surface de-icing are extremely corrosive.
8 Maintenance and do-it-yourself Maintenance requirements ..........................8 - 2 General maintenance ..............................8 - 2 Explanation of general maintenance items .........8 - 2 Maintenance precautions .........................
Y our new NISSAN has been designed to have minimum maintenance requirements with longer service intervals to save you both time and money . However, some day-to-day and regular maintenance is essential to maintain your NIS- SAN’s good mechanical condition, as well as its emission and engine performance.
When driving in areas using road salt or other corrosive materials, check lubrication frequently . Lights* Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely .
Windshield defroster Check that the air comes out of the defroster outlets properly and in sufficient quantity when operating the heater or air conditioner. Under the hood and vehicle The maintenance items listed here should be checked periodically (for example, each time you check the engine oil or refuel) .
When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle.
1. P ower steering fluid reservoir 2. Engine oil filler cap 3. Air cleaner 4. Brake fluid reservoir 5. Battery 6. Fuse/fusible link box 7. T ransmission dipstick 8. Engine oil dipstick 9. Radiator cap 10. Drive belt location 11. Fuse block 12. Windshield washer fluid reservoir 13.
The engine cooling system is filled at the factory with Genuine NISSAN Long Life Antifreeze/Coolant to provide year-round anti- freeze and coolant protection. The anti-freeze solution contains rust and corrosion inhibitors. Additional engine cooling system additives are not necessary .
CHANGING ENGINE COOLANT A NISSAN dealer can change the engine coolant. The service procedure can be found in the NISSAN Service Manual. Improper servicing can result in reduced heater performance and engine overheat- ing. WARNING ● T o avoid the danger of being scalded, never change the coolant when the en- gine is hot.
CAUTION Oil level should be checked regularly. Op- erating the engine with an insufficient amount of oil can damage the engine, and such damage is not covered by warranty. CHANGING ENGINE OIL 1. Park the vehicle on a level surface and apply the parking brake.
7. Refill engine with recommended oil through the oil filler opening, then install the oil filler cap securely . See “Capacities and recommended fuel/lubricants” in the “T echnical and con- sumer information” section of this manual for drain and refill capacity .
When checking or replacement is required, we recommend your NISSAN dealer for servicing. WARNING ● Use only Genuine NISSAN Matic K A TF . Do not mix with other fluids.
For further brake fluid specification information, refer to “Capacities and recommended fuel/lubricants” in the “T echnical and consumer information” section of this manual. WARNING Use only new fluid from a sealed con- tainer. Old, inferior or contaminated fluid may damage the brake system.
Refill the reservoir more frequently when driving conditions require an increased amount of win- dow washer fluid. Recommended fluid is Genuine NISSAN Wind- shield W asher Concentrate Cleaner & Anti- freeze or equivalent. CAUTION ● Do not substitute engine anti-freeze coolant for window washer solution.
1. Remove the battery caps with a screwdriver as shown. Use a cloth to protect the battery case. 2. Check the fluid level in each cell If it is necessary to add fluid, add only distilled water to bring the level up to the bottom of the filler opening.
1. P ower steering fluid pump 2. Crankshaft 3. Generator 4. Air conditioner WARNING Be sure the ignition key is in the OFF or LOCK position. The engine could rotate unexpectedly. 1. Visually inspect the belt(s) for signs of un- usual wear, cuts, fraying or looseness.
WARNING Be sure the engine and ignition switch are off and that the parking brake is engaged securely. CAUTION Be sure to use the correct socket to re- move the spark plugs. An incorrect socket can damage the spark plugs. If replacement is required, see your NISSAN dealer for assistance.
CLEANING If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running, wax or other material may be on the blade or windshield. Clean the outside of the windshield with a washer solution or a mild detergent.
Be careful not to let anything get into the washer nozzle s A . This may cause clogging or improper windshield washer operation. If something gets into the nozzle, remove it with a needle or small pin s B .
Rear window wiper blade s 1 Lift the wiper arm away from the rear win- dow . s 2 Push the wiper blade in and pivot until the blade becomes free. s 3 Insert a new blade onto the wiper arm and snap into place.
Self-adjusting brakes Y our vehicle is equipped with self-adjusting brakes. The front and rear disc-type brakes self-adjust every time the brake pedal is applied. WARNING See a NISSAN dealer for a brake system check if the brake pedal height does not return to normal.
3. Remove the fuse box cover by pushing the tab and lifting the cover up. 4. Remove the fuse with the fuse puller. The fuse puller is located in the center of the fuse block in the passenger compartment. 5. If the fuse is open s A , replace it with a new fuse s B .
2. Pull the sunglasses holder down to open s 1 . 3. Pull up on the sunglasses holder s 2 and remove to expose the fuse panel. 4. Remove the fuse with the fuse puller. 5. If the fuse is open s A , replace it with a known good fuse s B . 6. Push the fuse box cover to install.
K EYFOB Replace the battery in the keyfob as follows: s 1 Open the lid using a coin s A . s 2 Remove the battery s B . s 3 Install a new battery s C with the “+” facing down. Recommended battery: CR2025 or equivalent. s 4 Close the lid securely . 5.
HEADLIGHTS The headlight is a semi-sealed beam type which uses a replaceable headlight (halogen) bulb. If replacement is required, see your NISSAN dealer. CAUTION ● High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped.
1. Disconnect the negative (-) battery cable. 2. Remove the three splash shield screws and move the splash shield out of the way . 3. Disconnect the bulb connector. 4. Rotate the bulb counterclockwise and re- move. 5. Remove by pulling it straight out of the fog light assembly .
EXTERIOR AND INTERIOR LIGHTS Item W attage (W) Bulb No. Headlight assembly High 60 HB3/9005 Low* 51 HB4/9006 Park/T urn* 8/29 3457 Cornering* 27 3156 Front fog light 55 H11 Puddle lamp* 8 — Room/map lights 8 PL W 578 Personal lights T ype A 8 2GL T2P T ype B 8 TS578 Footwell 3.
1. Room/map light 2. Front personal lights 3. Step light 4. Puddle lamp 5. High-mounted stoplight 6. Cargo light 7. License plate light 8. Rear combination light 9. Headlight assembly 10. Fog light Replacement procedures All other lights are either type A , B, C or D.
Use a cloth s 1 to protect the housing. Use a cloth s 1 to protect the housing. Use a cloth s 1 to protect the housing. Room/map lights LDI0517 Personal lights – T ype A LDI0364 Personal lights – .
Use a cloth s 1 to protect the housing. Use a cloth s 1 to protect the housing. Step light LDI0341 Cargo light LDI0366 Rear combination light LDI0367 Maintenance and do-it-yourself 8-29 Z REVIEW COPY.
If you have a flat tire, see the “In case of emergency” section of this manual. TIRE PRESSURE Tire Pressure Monitoring System (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS) . It monitors tire pressure of all tires except the spare.
WARNING ● Improperly inflated tires can fail suddenly and cause an accident. ● The Gross V ehicle Weight Rating (GVWR) is located on the F .M .V .S.S./C .M .V .S.S. label. The vehicle weight capacity is indi- cated on the Tire and Loading Information label.
Tire and loading information label s 1 Seating capacity: The maximum num- ber of occupants that can be seated in the vehicle. s 2 V ehicle load limit: See loading infor- mation in the “T echnical and con- sumer information” section. s 3 Original tire size: The size of the tires originally installed on the vehicle at the factory .
Checking tire pressure 1. Remove the valve stem cap from the tire. 2. Press the pressure gauge squarely onto the valve stem. Do not press too hard or force the valve stem side- ways, or air will escape. If the hissing sound of air escaping from the tire is heard while checking the pressure, reposition the gauge to eliminate this leakage.
TIRE LABELING Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information iden- tifies and describes the fundamental characteristics of the tire and also pro- vides the tire identification number (TIN) for safety standard certification.
Michelin T PA X T Tire size (example: 225- 700R480A 100H) 1. Three-digit number (225): This num- ber gives the width in millimeters of the tire from sidewall edge to side- wall edge. 2. Three-digit number (700): This num- ber gives the outside diameter of the tire in millimeters.
s 2 TIN (Tire Identification Number) for a new tire (example: DO T XX XX XXX XXXX) 1. DO T : Abbreviation for the 9 Depart- ment Of T ransportation. 9 The symbol can be placed above, below or to the left or right of Tire Identification Num- ber. 2. T wo-digit code: Manufacturer’s identification mark 3.
The word 9 radial 9 is shown if the tire has radial structure. s 8 Manufacturer or brand name Manufacturer or brand name is shown. Other Tire-related T erminology In addition to the many terms that ar.
For additional traction on icy roads, studded tires may be used. However, some U.S. states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires.
● Do not drive at speeds above 50 MPH (80 km/h) and do not drive more than 125 miles (200 km) with a punctured Michelin T PA X T tire (if so equipped) . The actual distance the vehicle can be driven on a flat tire depends on outside temperature, vehicle load, road condi- tions and other factors.
CHANGING WHEELS AND TIRES Tire rotation NISSAN recommends rotating the tires every 7,500 miles (12,000 km) . See “Flat tire” in the “In case of emer- gency” section of this manual for tire re- placing procedures. As soon as possible, tighten the wheel nuts to the specified torque with a torque wrench.
● The original tires have built-in tread wear indicators. When the wear indicators are visible, the tire(s) should be replaced. ● Tires degrade with age and use. Have tires, including the spare, over 6 years old checked by a qualified technician because some tire damage may not be ob- vious.
Wheel balance Unbalanced wheels may affect vehicle handling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be bal- anced as required. Wheel balance service should be per- formed with the wheels off the vehicle.
CAUTION ● Do not use tire chains on a TEMPO- RAR Y USE ONL Y spare tire. Tire chains will not fit properly and may cause dam- age to the vehicle. ● Because the TEMPORAR Y USE ONL Y spare tire is smaller than the original tire, ground clearance is reduced.
8-44 Maintenance and do-it-yourself MEMO.
9 T echnical and consumer information Capacities and recommended fuel/lubricants .........9 - 2 Fuel recommendation ...........................9 - 3 Engine oil and oil filter recommendation ...........9 - 5 Recommended SAE viscosity number ...........
The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure described in the “Maintenance and do-it-yourself” section to determine the proper refill capacity. Capacity (Approximate) Recommended Fluids and Lubricants US measure Imp measure Liter Fuel 20 gal 16-5/8 gal 75.
FUEL RECOMMENDATION NISSAN recommends the use of unleaded pre- mium gasoline with an octane rating of at least 91 AKI (Anti-Knock Index) number (Research oc- tane number 96) .
T ake care not to spill gasoline during refu- eling. Gasoline containing oxygenates can cause paint damage. E–85 fuel E-85 fuel is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. E-85 can only be used in a Flexible Fuel V ehicle (FFV) .
ENGINE OIL AND OIL FILTER RECOMMENDATION Selecting the correct oil It is essential to choose the correct grade, quality and viscosity engine oil to ensure satisfactory engine life and performance. See 9 Capacities and recommended fuel/lubricants 9 earlier in this section.
Y our engine was filled with a high-quality engine oil when it was built. Y ou do not have to change the oil before the first recommended change interval.
ENGINE Model VQ35DE T ype Gasoline, 4-cycle, DOHC Cylinder arrangement 6-cylinder, V-block, Slanted at 60° Bore x Stroke in (mm) 3.760 x 3.205 (95.5 x 81.4) Displacement cu in (cm 3 ) 213.5 (3,498) Firing order 1–2–3–4–5–6 Idle speed No adjustment is necessary.
WHEELS AND TIRES Wheels 16 x 6.5JJ 17 x 6.5JJ Tires P225/65R16 P225/60R17 225-700R480A Spare tire T135/80*16 Speed rating 16” H 17” H P AX system H *: “R” or “D” depending on tire manufacturer DIMENSIONS AND WEIGHTS Overall length in (mm) 204.
When planning to drive your NISSAN ve- hicle in another country, you should first find out if the fuel available is suitable for your vehi- cle’s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline.
ENGINE SERIAL NUMBER The number is stamped on the engine as shown. F .M.V .S.S./C.M.V .S.S. CERTIFICATION LABEL The Federal/Canadian Motor V ehicle Safety Standard (F .
TIRE AND LOADING INFORMATION LABEL The cold tire pressure is shown on the Tire and Loading Information label. The label is located as shown. AIR CONDITIONER SPECIFICATION LABEL The air conditioner specification label is affixed as shown.
Use the following steps to mount the front license plate: Before mounting the license plate, confirm that the following parts are enclosed in the plastic bag: ● License plate bracket ● License plate bracket screws x 2 ● License plate screws x 2 ● Screw grommets x 2 1.
weight of occupants and cargo that can be loaded into the vehicle. If the vehicle is used to tow a trailer, the trailer tongue weight must be in- cluded as part of the cargo load. This information is located on the Tire and Loading Information label (if so equipped) .
Steps for determining correct load limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be trans- ferred to your vehicle.
WARNING Overloading or improper loading of a trailer and its cargo can adversely affect vehicle handling, braking and perfor- mance and may lead to accidents. CAUTION ● Do not tow a trailer or haul a heavy load for the first 500 miles (800 km) . Y our engine, axle or other parts could be damaged.
T emperature conditions can also affect towing. For example, towing a heavy trailer in high outside temperatures on graded roads can affect engine performance and cause overheating. The engine protection mode, which helps reduce the chance of engine damage, could activate and automati- cally decrease engine power.
T owing capacities are calculated assuming a base vehicle with driver and any options required to achieve the rating. Additional passengers, cargo and/or optional equipment, such as the trailer hitch, will add weight to the vehicle and reduce your vehicle’s maximum towing capacity and trailer tongue load.
to allow for proper tongue load. Always verify that available capacities are under the required rat- ings. T OWING LOAD/SPECIFICATION T OWING LOAD / SPECIFICA TION UNIT : lb (kg) Maximum T owing Load .
Tire pressures ● When towing a trailer, inflate the ve- hicle tires to the recommended cold tire pressure indicated on the Tire and Loading Information label. ● T railer tire condition, size, load rating and proper inflation pressure should be in accordance with the trailer and tire manufacturer’s specifications.
● Be certain your rearview mirrors conform to all federal, state or local regulations. If not, install any mirrors required for towing before driving the vehicle. ● Determine the overall height of the vehicle and trailer so the required clearance is known.
● For the first 500 miles (805 km) that you do tow , do not drive over 50 MPH (80 km/h) . ● Have your vehicle serviced more often than at intervals specified in the recommended Maintenance Schedule in the “NISSAN Ser- vice and Maintenance Guide” .
CAUTION ● Failure to follow these guidelines can result in severe transmission damage. ● Whenever flat towing your vehicle, al- ways tow forward, never backward. ● DO NO T tow any automatic transmis- sion vehicle with all four wheels on the ground (flat towing) .
WARNING The temperature grade for this tire is es- tablished for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, ei- ther separately or in combination, can cause heat build-up and possible tire failure.
Due to legal requirements in some states and Canadian Provinces, your vehicle may be re- quired to be in what is called the “ready condi- tion” for an Inspection/Maintenance (I/M) test of the emission control system. The vehicle is set to the “ready condition” when it is driven through certain driving patterns.
Y our vehicle is equipped with a variety of comput- ers that monitor and control a number of systems to optimize performance and help service techni- cians with diagnosis and repair. Some of the computers monitor emission control systems, braking systems, engine systems, transmission systems, tire pressure systems, and airbag sys- tems.
Insist on the use of genuine NISSAN collision parts! If you want your vehicle to be restored using parts made to NISSAN’s original exacting specifica- tions – if you want to help it to last and hold its resale value, the solution is simple. T ell your insurance agent and your repair shop to only use Genuine NISSAN Collision Parts.
9-28 T echnical and consumer information MEMO.
10 Index A Active head restraint .............. .1-7 Adjusting pedal position ........... .3-21 Air bag (See supplemental restraint system) .................... .1-51 Air bag system Front (See supplemental front impact air bag system) .............. .
CD player (See audio system) ........ .4-55 Child restraint with top tether strap ..... .1-30 Child restraints ...... .1-17, 1-18, 1-25, 1-27 Precautions on child restraints ........... .1-25, 1-40, 1-47 T op tether strap anchor point locations . .1-30 Child safety sliding door lock .
F Flashers (See hazard warning flasher switch) ..... .2-24 Flat tire ..................... .6-2 Floor mat positioning aid ............ .7-4 Fluid Brake fluid ................. .8-12 Capacities and recommended fuel/lubricants ................ .9-2 Engine coolant .
Keyless entry system (See remote keyless entry system) ...... .3-9 L Labels Air conditioner specification label .... .9-11 C.M.V .S.S. certification label ....... .9-10 Emission control information label .... .9-10 Engine serial number ........... .9-10 F .
Overheat If your vehicle overheats ......... .6-10 Owner’s manual order form ......... .9-25 Owner’s manual/service manual order information ................... .9-25 P Parking Parking brake check ........... .8-20 Parking brake operation ........
Setting button .......... .4-5, 4-11, 4-22 Shift lock release ............... .5-12 Shifting Automatic transmission .......... .5-11 Shoulder belt height adjustment ....... .1-24 Side air bag system (See supplemental side air bag and curtain side-impact air bag system) .
T ransceiver HomeLink T Universal T ransceiver .... .2-46 T ransmission Driving with automatic transmission . . . .5-10 Selector lever lock release ........ .5-12 T ravel (See registering your vehicle in another country) ..................... .9-9 T rip button .
MEMO.
MEMO.
MEMO.
MEMO.
MEMO.
MEMO.
MEMO.
RECOMMENDED FUEL: NISSAN recommends the use of unleaded pre- mium gasoline with an octane rating of at least 91 AKI (Anti-Knock Index) number (Research oc- tane number 96) .
1. Engine oil 8-8 2. Window washer fluid 8-12 3. Engine coolant 8-7 4. Power steering fluid 8-11 5. Meters and gauges 2-3 6. Audio system 4-43; Climate controls 4-31, 4-40 7. Spare tire 6-2 8. Fuel-filler door release 3-19; Fuel recom- mendation 9-3 9.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Nissan vehicle c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Nissan vehicle - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Nissan vehicle, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Nissan vehicle va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Nissan vehicle, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Nissan vehicle.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Nissan vehicle. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Nissan vehicle ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
