Manuel d'utilisation / d'entretien du produit Quest (2008) du fabricant Nissan
Aller à la page of 375
W elcome to the growing family of new NISSAN owners. This vehicle is delivered to you with confidence. It was produced using the latest techniques and strict quality control. This manual was prepared to help you under- stand the operation and maintenance of your vehicle so that you may enjoy many miles (kilome- ters) of driving pleasure.
This manual includes information for all options available on this model. Therefore, you may find some information that does not apply to your vehicle. All information, specifications and illustrations in this manual are those in effect at the time of printing.
CALIFORNIA PERCHLORATE ADVISORY Some vehicle parts, such as lithium batter- ies, may contain perchlorate material. The following advisory is provided: “Perchlorate Material – special handling may apply, See www.dtsc .ca.gov/hazardouswaste/perchlorate.
NISSAN CARE S... Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Y our satisfaction with your vehicle and your NISSAN dealer are our primary concerns. Y our NISSAN dealer is always available to assist you with all your automobile sales and service needs.
T able of Contents Illustrated table of contents Safety—Seats, seat belts and supplemental restraint system Instruments and controls Pre-driving checks and adjustments Display screen, heater, air co.
Z REVIEW COPY— 2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X I n f o r m a t i o n P r o v i d e d b y :.
0 Illustrated table of contents Airbags, seat belts and child restraints ...............0 - 2 Exterior front ......................................0 - 3 Exterior rear .......................................0 - 4 Passenger compartment .................
1. 3rd row bench center seat belt (P . 1-15) 2. 3rd row bench seat belts (P . 1-15) 3. T op tether strap anchor points (P . 1-30) 4. 2nd row captain’s chair seat belts (P . 1-15) 5. Front seat belts (P . 1-15) 6. Roof mounted curtain side-impact air bag (P .
1. Engine hood (P . 3-14) 2. Headlight and turn signal switch (P . 2-18) 3. Replacing bulbs (P . 8-27) 4. Windshield wiper and washer switch (P . 2-16) 5. Windshield (P . 8-17) 6. P ower windows (P . 2-36) 7. Door locks, keyfob, keys (P . 3-3, 3-9, 3-2) 8.
1. Rear window defroster switch (P . 2-18) 2. V ehicle loading (P . 9-12) 3. Lift gate (P . 3-14) 4. Lift gate release (P . 3-18) 5. Rear view monitor (if so equipped) (P .4-28) 6. Replacing bulbs (P . 8-27) 7. Fuel-filler cap, fuel recommendation (P .
1. DVD entertainment system (if so equipped) (P . 4-65) 2. Personal lights (P . 2-42) 3. Skyview roof (if so equipped) (P . 2-39) 4. Moonroof (if so equipped) (P . 2-40) 5. Map lights (P . 2-43) , Console light P .2-44) 6. Sun visors (P . 3-22) 7. HomeLink T (if so equipped) (P .
1. V entilators (P . 4-30) 2. Headlight/fog light (if so equipped)/turn signal switch (P . 2-18) 3. Steering wheel switch for audio control/Bluetooth T hands-free phone system (if so equipped) (P . 4-62) 4. Driver supplemental air bag/horn (P . 1-52, P .
17. Shift selector lever (P . 5-8) 18. Ignition switch (P . 5-6) 19. Tilt steering wheel control (P . 3-21) 20. Rear sonar system off switch (if so equipped) (P . 2-25) 21. V ehicle Dynamic Control (VDC) off switch (if so equipped) or T raction Control System (T CS) off switch (if so equipped) (P .
1. P ower steering fluid reservoir (P . 8-11) 2. Engine oil filler cap (P . 8-8) 3. Air cleaner (P . 8-16) 4. Brake fluid reservoir (P . 8-12) 5. Battery (P . 8-13) 6. Fuse/fusible link box (P . 8-20) 7. T ransmission dipstick (P . 8-11) 8. Engine oil dipstick (P .
W arning light Name Page or Anti-lock Braking System (ABS) warn- ing light 2-8 or Brake warning light 2-8 Charge warning light 2-8 Door open warning light 2-8 Engine oil pressure warning light 2-9 Low.
0-10 Illustrated table of contents MEMO I n f o r m a t i o n P r o v i d e d b y :.
1 Safety—Seats, seat belts and supplemental restraint system Seats ............................................1 - 2 Front manual seat adjustment (if so equipped) ................................1 - 2 Front power seat adjustment (if so equipped) ...
WARNING ● Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident, you could be thrown into it and receive neck or other serious injuries. Y ou could also slide under the lap belt and receive serious internal injuries.
Forward and backward Pull the lever up and hold it while you slide the seat forward or backward to the desired position. Release the lever to lock the seat in position. Reclining T o recline the seatback, pull the lever up and lean back. T o bring the seatback forward, pull the lever up and lean your body forward.
Lumbar support (driver’s seat) The lumbar support feature provides lower back support to the driver. Move the lever up or down to adjust the seat lumbar area. FRONT POWER SEAT ADJUSTMENT (if so equipped) Operating tips ● The power seat motor has an auto-reset overload protection circuit.
The reclining feature allows adjustment of the seatback for occupants of different sizes for added comfort and to help obtain proper seat belt fit (see “Precautions on seat belt usage” later in this section) . Also, the seatback can be re- clined to allow occupants to rest when the ve- hicle is stopped and the transmission is in P (Park) .
2ND ROW CAPTAIN’S CHAIR ADJUSTMENT Forward and backward WARNING ● The 2nd row seats are heavy. Be careful when folding and unfolding. ● T o avoid injury to yourself and others, keep hands and body clear when folding. While seated, pull the lever s 1 and hold it while you slide s 2 the seat forward or backward to the desired position.
Tip up for easy entry to the 3rd row The 2nd row captain’s chairs can be tipped for- ward for easy entry or exit from the 3rd row bench seat. T o enter the 3rd row bench seat , lift up on the lever located on the lower base of the 2nd row captain’s chair to tip the seat forward.
● Do not attach anything to the head re- straint stalks. Doing so could impair Active Head Restraint function. The Active Head Restraint moves forward utiliz- ing the force that the seatback receives from the occupant in a rear-end collision.
Adjust the head restraint so the center is level with the center of your ears. ARMRESTS T o use the armrests, pull them down to the rest- ing position. s A Resting position s B Stowed position Adjustable front seat armrest’s (if so equipped) T o use the adjustable seat armrest, pull it down to the resting position.
● If the head restraints are removed for any reason, they should be securely stored to prevent them from causing injury to passengers or damage to the vehicle in case of sudden braking or an accident. ● When returning the seatbacks to the upright position, be certain they are completely secured in the latched posi- tion.
s 3 Push down on the small knob on the back of the seat to release the base of the seat. s 4 Then fold the entire seat forward into the stowed position in the floor. s 5 Reverse this process to return the 2nd row captain’s chairs to a seating position.
Folding T o fold the seatback forward, for cargo hauling, lift up on the latch in the center of the seatback to fold the seatback over the seat base. Folding the 3rd row bench seat WARNING ● The 3rd row bench seat is heavy. Be careful when folding and unfolding.
3. Pull back on the pull strap to release the back of the seat. Rotate the seatback toward the back of the vehicle. 4. Pull up on the lever located on the back of the seat base. This will fold the seat base toward the back of the vehicle. 5. The entire seat will rotate toward you and stow in the floor.
6. The rear seat anchors are spring loaded and can be folded into the side panels to maxi- mize cargo space. The anchors are held in the folded position by the items in the cargo area. When the load is removed from the cargo area, the rear seat anchors automati- cally return to the unfolded position.
PRECAUTIONS ON SEAT BELT USAGE If you are wearing your seat belt properly ad- justed and you are sitting upright and well back in your seat with both feet on the floor, your chances of being injured or killed in an accident and/or the severity of injury may be greatly reduced.
WARNING ● Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be properly re- strained in the rear seat and, if appro- priate, in a child restraint. WARNING ● The seat belt should be properly ad- justed to a snug fit.
WARNING ● Always route the shoulder belt over your shoulder and across your chest. Never run the belt behind your back, under your arm or across your neck. The belt should be away from your face and neck, but not falling off your shoulder. ● Position the lap belt as low and snug as possible AROUND THE HIPS, NO T THE WAIST .
There are three basic types of child restraint systems: ● Rear facing child restraint ● Front facing child restraint ● Booster seat The proper restraint depends on the child’s size. Generally , infants up to about 1 year and less than 20 pounds (9 kg) should be placed in rear facing child restraints.
have a label certifying that it complies with Fed- eral Motor V ehicle Safety Standards or Canadian Motor Vehicle Safety Standards. Once the child has grown so the shoulder belt is no longer on or near the face and neck, use the shoulder belt without the booster seat.
s 2 Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until you hear and feel the latch engage. ● The retractor is designed to lock during a sudden stop or on impact. A slow pulling motion permits the seat belt to move, and allows you some freedom of movement in the seat.
WARNING When fastening the seat belts, be certain that the seatbacks are completely se- cured in the latched position. If they are not completely secured, passengers may be injured in an accident or sudden stop. Unfastening the seat belts s 1 T o unfasten the seat belt, press the button on the buckle.
Center of the 3rd row bench seat The 3rd row center seat belt has a connector tongue s 1 and a seat belt tongue s 2 . Both the connector tongue and the seat belt tongue must be securely latched for proper seat belt opera- tion. WARNING ● Always fasten the connector tongue and the seat belt in the order shown.
Stowing the 3rd row center seat belt When folding down the 3rd row seat, the 3rd row center seat belt can be retracted into a stowed position as follows: s 1 Hold the connector tongue so that the seat belt does not retract suddenly when the tongue is released from the connector buckle.
Attaching the 3rd row center seat belt Always be sure the 3rd row center seat belt connector tongue and connector buckle are at- tached. Disconnect only when folding down the rear seat. T o connect the buckle: s 1 Pull out the connector tongue from the re- tractor base.
WARNING ● After adjustment, release the adjust- ment button and try to move the shoul- der belt anchor up and down to make sure it is securely fixed in position.
PRECAUTIONS ON CHILD RESTRAINTS WARNING ● Infants and small children should al- ways be placed in an appropriate child restraint while riding in the vehicle. Failure to use a child restraint can re- sult in serious injury or death. ● Infants and small children should never be carried on your lap.
● If the child restraint is not anchored properly, the risk of a child being in- jured in a collision or a sudden stop greatly increases. ● Child restraint anchor points are de- signed to withstand only those loads imposed by correctly fitted child re- straints.
LOWER ANCHORS AND T ETHERS FOR CHILDREN S Y STEM (LA T CH) Y our vehicle is equipped with special anchor points that are used with Lower Anchors and T ethers for CHildren System (LA T CH) compat- ible child restraints.
● Child restraint anchor points are de- signed to withstand only those loads imposed by correctly fitted child re- straints. Under no circumstance are they to be used for adult seat belts or harnesses.
straint installation using LA T CH on 3rd row bench seat (if so equipped)” in this section. T OP TETHER STRAP CHILD RESTRAINT If the manufacturer of your child restraint requires the use of a top tether strap, it must be secured to the anchor point.
Front passenger seat (2 passenger cargo van only) For the front passenger seat in the 2 passenger cargo van only , install the top tether strap as follows: 1. Adjust the head restraint to its highest posi- tion. 2. Route the top tether strap between the head restraint and the top of the seatback.
4. Tighten the tether strap according to the manufacturer’s instructions to remove any slack. For best child restraint fit, see the child restraint installation instructions in this section and the child restraint manufacturer’s instructions. 3rd row bench seat (if so equipped) 1.
3. Tighten the tether strap according to the manufacturer’s instructions to remove any slack. For best child restraint fit, see the child restraint installation instructions in this section and the child restraint manufacturer’s instructions.
is removed. If the seating position does not have an adjustable head restraint and it is interfering with the proper child restraint fit, try another seating position or a different child restraint. 5. For child restraints that are equipped with webbing mounted attachments, remove any additional slack from the anchor attach- ments.
8. Check to make sure the child restraint is properly secured prior to each use. If the child restraint is loose, repeat steps 4 through 7. Rear-facing Follow these steps to install a rear-facing child restraint in the 2nd row captain’s chairs using LA T CH: 1.
5. For child restraints that are equipped with webbing mounted attachments, remove any additional slack from the anchor attach- ments. Press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments.
● Inspect the lower anchors by inserting your fingers into the lower anchor area and feeling to make sure there are no obstructions over the LA TCH anchors, such as seat belt webbing or seat cush- ion material. The child restraint will not be secured properly if the LA TCH an- chors are obstructed.
5. For child restraints that are equipped with webbing mounted attachments, remove any additional slack from the anchor attach- ments. Press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments 6.
8. Check to make sure the child restraint is properly secured prior to each use. If the child restraint is loose, repeat steps 3 through 8. Rear-facing Follow these steps to install a rear-facing child restraint in the 3rd row bench seats using LA T CH: 1.
5. For child restraints that are equipped with webbing mounted attachments, remove any additional slack from the anchor attach- ments. Press downward and rearward firmly in the center of the child restraint with your hand to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments.
CHILD RESTRAINT INSTALLATION USING THE SEAT BELTS WARNING ● Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the front passenger seat. Front air bags inflate with great force. A rear-facing child restraint could be struck by the front air bag in a crash and could seriously injure or kill your child.
Front-facing Follow these steps to install a front-facing child restraint using the vehicle seat belt in the rear seats or in the front passenger seat: 1. If you must install a child restraint in the front seat, it should be placed in a front-facing direction only.
4. Pull the shoulder belt until the belt is fully extended. At this time, the seat belt retractor is in the Automatic Locking Retractor (ALR) mode (child restraint mode) . It reverts to the Emergency Locking Retractor (ELR) mode when the seat belt is fully retracted.
7. If the child restraint is equipped with a top tether strap, route the top tether strap and secure the tether strap to the tether anchor point. See “T op tether strap child restraint” in this section. Do not install child restraints that require the use of a top tether strap to seating positions that do not have a top tether anchor.
Rear-facing Follow these steps to install a rear-facing child restraint using the vehicle seat belt in the rear seats: 1. Child restraints for infants must be used in the rear-facing direction and therefore must not be used in the front seat. Position the child restraint on the seat.
4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt. 5. Remove any additional slack from the child restraint; press downward and rearward firmly in the center of the child restraint to compress the vehicle seat cushion and seat- back while pulling up on the seat belt.
7. Check that the retractor is in the ALR mode by trying to pull more seat belt out of the retractor. If you cannot pull any more seat belt webbing out of the retractor, the retrac- tor is in the ALR mode. 8. Check to make sure that the child restraint is properly secured prior to each use.
● Do not use towels, books, pillows or other items in place of a booster seat. Items such as these may move during normal driving or a collision and result in serious injury or death.
● Make sure the child’s head will be properly supported by the booster seat or vehicle seat. The seat back must be at or above the center of the child’s ears. For example, if a low back booster seat s 1 is chosen, the vehicle seat back must be at or above the center of the child’s ears.
1. If you must install a booster seat in the front seat, move the seat to the rear- most position. 2. Position the booster seat on the seat. Only place it in a front facing direction. Always follow the booster seat manufacturer’s in- structions. 3. The booster seat should be positioned on the vehicle seat so that it is stable.
4. Position the lap portion of the seat belt low and snug on the child’s hips. Be sure to follow the booster seat manufacturer’s in- structions for adjusting the belt routing. 5. Pull the shoulder belt portion of the seat belt toward the retractor to take up extra slack.
PRECAUTIONS ON SUPPLEMENTAL RESTRAINT SYSTEM This Supplemental Restraint System (SRS) sec- tion contains important information concerning the following systems: ● Driver and passenger supplemental f.
WARNING ● The front air bags ordinarily will not inflate in the event of a side impact, rear impact, rollover, or lower severity fron- tal collision. Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents.
WARNING ● Never let children ride unrestrained or extend their hands or face out of the window. Do not attempt to hold them in your lap or arms. Some examples of dangerous riding positions are shown in the illustrations.
WARNING ● Children may be severely injured or killed when the front air bags, side air bags or curtain air bags inflate if they are not properly restrained.
WARNING ● Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the front seat. An in- flating front air bag could seriously in- jure or kill your child. See “Child re- straints” earlier in this section for details.
WARNING ● The seat belts, the side air bags and curtain air bags are most effective when you are sitting well back and upright in the seat with both feet on the floor.
1. Roof-mounted curtain side-impact supplemental air bag inflators 2. Roof-mounted curtain side-impact supplemental air bag (driver’s side) 3. Seat belt buckle switches 4. Supplemental front-impact air bag modules 5. Crash zone sensor 6. Air bag Control Unit (ACU) 7.
8. Occupant classification sensor (pressure sensor) 9. Seat belt with pretensioner 10. Satellite sensors 11. Front seat-mounted side-impact supplemental air bag modules 12.
The front air bags operate only when the ignition switch is in the ON or START posi- tion. After turning the ignition key to the ON position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7 seconds if the system is operational.
The purpose of the regulation is to help reduce the risk of injury or death from an inflating air bag to certain front passenger seat occupants, such as children, by requiring the air bag to be auto- matically turned OFF . Certain sensors are used to meet the requirements.
the air bag might inflate in a crash) , it could be that the child restraint or seat belt is not being used properly. Make sure that the child restraint is installed properly, the seat belt is used properly and the occupant is positioned properly .
● No unauthorized changes should be made to any components or wiring of the seat belt system. This may affect the front air bag system. T ampering with the seat belt system may result in seri- ous personal injury. ● Work on and around the front air bag system should be done by a NISSAN dealer.
practical from the door finishers and side roof rails. The side air bags and curtain air bags inflate quickly in order to help protect the front and rear outboard occupants.
● If the vehicle becomes involved in a frontal collision but a pretensioner is not activated, be sure to have the pre- tensioner system checked and, if nec- essary, replaced by your NISSAN dealer. ● No unauthorized changes should be made to any components or wiring of the pretensioner system.
1. SRS Front Air Bag W arning Labels 2. SRS Front Seat-Mounted Side-Impact Supplemental Air Bag W arning Label SUPPLEMENTAL AIR BAG WARNING LABELS W arning labels about the supplemental front- impact .
Repair and replacement procedure The front air bags, side air bags, curtain air bags and pretensioners are designed to inflate on a one-time-only basis. As a reminder, unless it is damaged, the supplemental air bag warning light remains illuminated after inflation has occurred.
2 Instruments and controls Instrument panel ...................................2 - 2 Meters and gauges ................................2 - 3 Speedometer and odometer .....................2 - 4 T achometer ....................................2 - 5 Engine coolant temperature gauge .
Cup holders .................................. 2-32 Cargo organizer (if so equipped) ................ 2-34 3rd row armrest bin ............................ 2-35 Cargo area storage bin ......................... 2-35 Garment hook .......................
1. V entilators (P . 4-30) 2. Headlight/fog light (if so equipped)/turn signal switch (P . 2-18) 3. Steering wheel switch for audio control/Bluetooth T hands-free phone system (if so equipped) (P . 4-62) 4. Driver supplemental air bag/horn (P . 1-52, P .
17. Shift selector lever (P . 5-8) 18. Ignition switch (P . 5-6) 19. Tilt steering wheel control (P . 3-21) 20. Rear sonar system off switch (if so equipped) (P . 2-25) 21. V ehicle Dynamic Control (VDC) off switch (if so equipped) or T raction Control System (T CS) off switch (if so equipped) (P .
1. Speedometer 2. Odometer 3. Change button SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates vehicle speed. Odometer/T win trip odometer The odometer/twin trip odometer is displayed when the ignition switch is in the ON position. The odometer records the total distance the ve- hicle has been driven.
T ACHOMETER The tachometer indicates engine speed in revo- lutions per minute (rpm) . Do not rev the engine into the red zone s 1 . CAUTION When engine speed approaches the red zone, shift to a higher gear or reduce en- gine speed. Operating the engine in the red zone may cause serious engine damage.
FUEL GAUGE The gauge indicates the approximate fuel level in the tank. The gauge may move slightly during braking, turning, acceleration, or going up or down hills. The gauge needle returns to E (Empty) after the ignition key is turned to OFF . The low fuel warning light comes on when the amount of fuel in the tank is getting low .
or Anti-lock Braking System (ABS) warning light Seat belt warning light and chime Front passenger air bag status light or Brake warning light Supplemental air bag warning light Security indicator ligh.
W ARNING LIGHTS or Anti-lock Braking System (ABS) warning light When the ignition switch is in the ON position, the Anti-lock Braking System (ABS) warning light illuminates and then turns off.
Engine oil pressure warning light This light warns of low engine oil pressure. If the light flickers or comes on during normal driving, pull off the road in a safe area, stop the engine immediately and call a NISSAN dealer or other authorized repair shop.
● If the light illuminates while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Driving with under-inflated tires may permanently damage the tires and in- crease the likelihood of tire failure.
● The supplemental air bag warning light does not come on at all. Unless checked and repaired, the supplemental restraint systems (air bag system) and/or the pretensioners may not function properly.
ness for inspection/maintenance (I/M) test” in the “T echnical and consumer information” section of this manual. Operation The Malfunction Indicator Light will come on in one of two ways: ● Malfunction Indicator Light on steady — An emission control system malfunction has been detected.
Push the traction control off switch again or re- start the engine and the system will operate nor- mally . See “T raction Control System (T CS)” in the “Starting and driving” section of this manual. The traction control light also comes on when you turn the ignition key to the ON position.
Y our vehicle has two types of security systems: ● V ehicle security system ● NISSAN V ehicle Immobilizer System V EHICLE SECURITY SYSTEM The vehicle security system provides visual and audible alarm signals if someone opens the doors when the system is armed.
glow for 30 seconds, unlock the driv- er’s door once and lock it again. ● Even when the driver and/or passen- gers are in the vehicle, the system will arm with all doors closed and locked with the ignition key in the OFF posi- tion.
Security indicator light The security indicator light blinks whenever the ignition switch is in the L OCK, OFF or ACC position. This function indicates the NISSAN V e- hicle Immobilizer System is operational. If the NISSAN Vehicle Immobilizer System is mal- functioning, the light will remain on while the ignition key is in the ON position.
CAUTION ● Do not operate the washer continu- ously for more than 30 seconds. ● Do not operate the washer if the reser- voir tank is empty. ● Do not fill the window washer reservoir tank with washer fluid concentrates at full strength.
T o defrost the rear window glass and outside mirrors (if so equipped) , start the engine and push the rear window defroster switch on. The rear window defroster indicator light comes on. Push the switch again to turn the defroster off. The rear window defroster automatically turns off after approximately 15 minutes.
CAUTION Use the headlights with the engine run- ning to avoid discharging the vehicle battery. Autolight system (if so equipped) The autolight system allows the headlights to be set so they turn on and off automatically.
Be sure you do not put anything on top of the autolight sensor s 1 located on top of the instrument panel. The autolight sensor controls the autolight ; if it is covered, the autolight sensor reacts as if it is dark out and the headlights will illuminate.
WARNING When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.
T URN SIGNAL SWITCH T urn signal s 1 Move the lever up or down to signal the turning direction. When the turn is com- pleted, the turn signals cancel automatically . Lane change signal s 2 T o signal a lane change, move the lever up or down to the point where the indicator light begins to flash, but the lever does not latch.
CORNERING LIGHT The cornering light provides additional illumina- tion toward the turning direction. The cornering light will illuminate on the turning direction side when a turn is signaled with the headlights on. Push the switch on to warn other drivers when you must stop or park under emergency condi- tions.
T o sound the horn, push the center pad area of the steering wheel. WARNING Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system. T am- pering with the supplemental front air bag system may result in serious personal injury.
The vehicle should be driven with the T raction Control System (T CS) on for most driving condi- tions. If the vehicle is stuck in mud or snow , the TCS reduces the engine output to reduce wheel spin. The engine speed will be reduced even if the accelerator is depressed to the floor.
The rear sonar system can be disabled by push- ing the OFF switch. When the system is disabled, the indicator light on the switch will illuminate. The system will automatically reset the next time the ignition switch is turned on. See “Rear sonar system” in the “Starting and driving” section.
● Avoid using power outlets when the air conditioner, headlights or rear window defroster is on. ● Before inserting or disconnecting a plug, be sure the electrical accessory being used is turned OFF . ● Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal temperature fuse may open.
CONSOLE BOX (if so equipped) Push the corresponding button s 1 to open the small storage compartments. Press the front portion of the lid s 2 down from the handle area until it stops. While keeping the downward force applied, push the lid rearward s 3 to the desired opening amount.
CENTER TRAY TABLE (if so equipped) T o use the center tray table, raise it up until it locks into the upright position. T o access the small storage compartment on the top of the tray table, raise the lid. CAUTION T o avoid damaging it, do not apply a total load of more than 50 lbs (23 kg) to the center tray table.
GLOVE BOX Open the glove box by pulling the handle. Use the master key when locking s 1 or unlocking s 2 the glove box. The valet key cannot be used to lock or unlock the glove box. WARNING Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop.
SEATBACK POCKETS The seatback pockets are located on the back of the driver’s and passenger’s seats. The pockets can be used to store maps. GROCERY HOOKS The grocery hooks allow for standard size plastic grocery bags to hang side by side. CAUTION Do not apply a total load of more than 18 lbs (8 kg) to a single grocery hook.
OVERHEAD CONSOLE WARNING Keep storage bins closed while driving to help prevent injury in an accident or a sudden stop. Large storage bin Push the button to open the storage bin. Push the lid up to close. Small storage bin Push the button to open the small storage bin.
T o use the cup holders, raise the center tray table. Refer to “Center tray table” earlier in this section. 2nd row 3rd row T ype B LIC0896 LIC0509 WIC0947 Instruments and controls 2-33 Z REVIEW C.
Soft bottle holder CAUTION ● Do not use bottle holder for any other objects that could be thrown about in the vehicle and possibly injure people during sudden braking or an accident. ● Do not use bottle holder for open liquid containers. CARGO ORGANIZER (if so equipped) T o access the cargo organizer: 1.
3RD ROW ARMREST BIN Raise the lid to open the 3rd row armrest bin. CARGO AREA STORAGE BIN T o open the cargo area storage bin, turn the knob counterclockwise s 1 . The lid can be removed. T o close, replace the lid and turn the knob clock - wise s 2 .
ROOF RACK (if so equipped) Always distribute the luggage evenly on the roof rack. Do not load more than 125 lb (56 kg) . Be careful that your vehicle does not exceed the Gross Vehicle W eight Rating (GVWR) or its Gross Axle Weight Rating (GAWR front and rear) .
1. Window lock button 2. P ower door lock switch 3. Front passenger’s side automatic switch 4. Right rear power vent window switch (if so equipped) 5.
Automatic operation T o fully open a window equipped with automatic operation, press the window switch down (only driver’s side shown) to the second detent and release it; it need not be held. The window auto- matically opens all the way. T o stop the window, lift the switch up while the window is opening.
The power vent windows operate when the igni- tion key is in the ON position, or for 45 seconds after the ignition key is turned to the OFF position. If the driver’s or passenger’s door is opened during this 45 second period, power to the vent windows is cancelled.
AUTOMATIC MOONROOF The moonroof will only operate when the ignition switch is in the ON position. The automatic moonroof is operational for about 45 seconds, even if the ignition switch is turned to the ACC or OFF position.
If the auto reverse function malfunctions and re- peats opening or tilting up the moonroof, keep pushing the tilt down switch within 5 seconds after it happens; the moonroof will fully close gradually . Make sure nothing is caught in the moonroof. WARNING ● In an accident you could be thrown from the vehicle through an open moonroof.
● The doors are unlocked by the keyfob, a key or the power door lock switch while all doors are closed and the ignition switch is in the OFF position. ● The driver’s door is opened and then closed while the key is removed from the ignition switch.
The personal lights on the overhead console (T ype B) can be swiveled 360 degrees. T o turn on the light, press the button. Press the button again to turn off the light. The cargo light on the overhead trim (T ype C) has a three-position switch. T o operate, push the light.
CONSOLE LIGHT The console light s 1 will turn on whenever the parking lights or headlights are illuminated. The console light brightness can be adjusted (if so equipped) with the illumination brightness control.
PROGRAMMING HOMELINK T 1. T o begin, press and hold the two outer HomeLink T buttons (to clear the memory) until the indicator light s 1 blinks (after 20 seconds) . Release both buttons. 2. Position the end of the hand-held transmitter 1 - 3 inches (26 - 76 mm) away from the HomeLink T surface.
NO TE: Once you have pressed and released the program button on the garage door open- er’s motor and the “training light” is lit, you have 30 seconds in which to perform step 7. Use the help of a second person for conve- nience to assist when performing this step.
CLEARING THE PROGRAMMED INFORMATION Individual buttons cannot be cleared. However, to clear all programming, press and hold the two outside buttons and release when the indicator light begins to flash (approximately 20 seconds) .
2-48 Instruments and controls MEMO I n f o r m a t i o n P r o v i d e d b y :.
3 Pre-driving checks and adjustments K e y s .............................................3 - 2 NISSAN vehicle immobilizer system keys ..........3 - 2 Doors ............................................3 - 3 Locking with key ...........................
1. T wo master keys (black) with transpon- der chip and chrome NISSAN brand symbol on one side 2. V alet key (black) with transponder chip 3. K ey number plate 4. T ransponder chip A key number plate is supplied with your keys. Record the key number and keep it in a safe place (such as your wallet) , not in the vehicle.
WARNING ● Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally open- ing the doors, and will help keep out intruders.
Opening and closing windows The driver’s door key operation allows you to open and close windows equipped with auto- matic operation at the same time. ● T o open the windows, turn the driver’s door key toward the rear of the vehicle for longer than 1 second after the door is unlocked.
LOCKING WITH POWER DOOR LOCK SWITCH T o lock all the doors without a key, push the door lock switch (driver’s or front passenger’s side) , to the lock position s 1 . When locking the door this way , be certain not to leave the key inside the vehicle.
USING THE MAIN ON/OFF SWITCH FOR THE POWER SLIDING DOOR (if so equipped) The main ON/OFF switch is located in the over- head console. Push the switch ON to enable the door pillar switches and the power assist feature. An indica- tor light will illuminate when the switch is in the ON position.
Power Assist : If the main on/off switch is ON and a sliding door is unlocked and manually moved toward the open or close position using the inside or outside handle, the power assist feature will be activated and the door will complete its motion automati- cally .
WARNING There are some small distances immedi- ately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc .
CHILD SAFETY SLIDING DOOR LOCK The child safety lock helps prevent the sliding door from being opened accidentally, especially when small children are in the vehicle.
CAUTION Listed below are conditions or occur- rences which will damage the keyfob: ● Do not allow the keyfob to become wet. ● Do not drop the keyfob. ● Do not strike the keyfob sharply against another object. ● Do not place the keyfob for an extended period in an area where temperatures exceed 140°F (60°C) .
Unlocking doors Push the button on the keyfob once. ● Only the driver’s door unlocks. ● The hazard indicator flashes once if all doors are completely closed with the ignition key in any position except the ON position.
Operating the power sliding door (if so equipped) Push and hold the button on the keyfob for about 0.5 second to open or close the power sliding door. The door will reverse direction immediately dur- ing power open or power close if the keyfob button is pressed.
Silencing the horn beep feature If desired, the horn beep feature can be deacti- vated using the keyfob. NO TE: If you use the keyfob to change the horn beep and lamp flash feature for vehicles with color screen, the display will not show the current mode and cannot be used to change the mode.
s 1 Pull the hood lock release handle located below the driver’s side instrument panel. The hood will spring up slightly . s 2 Push the lever at the front of the hood to the side as illustrated with your fingertips and raise the hood. s 3 Insert the support rod into the slot on the underside of the hood.
OPERATING THE MANUAL LIFT GATE The power door lock system allows you to lock or unlock all doors including the lift gate simulta- neously . T o open the lift gate, depress the opener handle and lift up. T o close, lower and push the lift gate down se- curely .
OPERATING THE POWER LIFT GATE (if so equipped) NO TE: T o open, close or reverse the power lift gate, the shift selector lever must be in P (Park) . Also, the power lift gate will not operate if battery voltage is low.
Reverse: The power lift gate will reverse direction immedi- ately during power open or power close if the keyfob, overhead console or rear pillar switch is pressed.
CAUTION ● If the power lift gate does not stay open or if the lift gate unexpectedly closes at any time while a continuous warning chime sounds, do not operate the lift gate. There may be a pressure loss in one or both of the lift gate gas stays. Have the lift gate inspected by a NISSAN dealer.
P ower lift gate (if so equipped) If the lift gate cannot be opened with the door lock switch or keyfob due to a discharged battery, follow these steps: 1. Remove the cover on the inside of the lift gate. 2. Move the lever up to open the lift gate. OPENER OPERATION The fuel-filler door release is located on the driv- er’s door.
WARNING ● Gasoline is extremely flammable and highly explosive under certain condi- tions. Y ou could be burned or seriously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling.
TILT OPERATION Pull the lock lever forward and adjust the steering wheel up or down to the desired position. Push the lock lever back to lock the steering wheel in place. WARNING Do not adjust the steering wheel while driving. Y ou could lose control of your vehicle and cause an accident.
s 1 T o block glare from the front, swing down the main sun visor. s 2 T o block glare from the side, remove the main sun visor from the center mount and swing the visor to the side. s 3 Slide the sun visor in or out as needed. V ANITY MIRRORS T o access the vanity mirror, pull the sun visor down and flip open the mirror cover.
REARVIEW MIRROR (if so equipped) The night position s 1 reduces glare from the headlights of vehicles behind you at night. Use the day position s 2 when driving in daylight hours. WARNING Use the night position only when neces- sary, because it reduces rear view clarity.
OUTSIDE MIRRORS WARNING Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mirror or glance over your shoulder to properly judge distances to other objects.
Foldable outside mirrors Push the mirrors backward to fold them. Reverse tilt-down feature (if so equipped) The reverse tilt-down feature will turn the se- lected outside mirror surface downward to pro- vide better rear visibility close to the vehicle.
MEMORY STORAGE FUNCTION T wo positions for the driver’s seat, accelerator and brake pedals, and outside mirrors can be stored in the automatic drive positioner memory. Follow these procedures to use the memory sys- tem. 1. Set the automatic transmission selector le- ver to the P (Park) position.
stored memory position can be set again. Drive the vehicle over 25 MPH (40 km/h) to restart the memory storage function. Y ou can also restart the memory storage function using the following procedure. 1. Connect the battery cable or replace the fuse.
● When the memory switch (1 or 2) is not pushed and held for at least 1 second. ● When the seat has been already moved to the memorized position. ● When no seat position is stored in the memory switch. ● When the shift selector lever is moved from P (Park) to any other position.
Pre-driving checks and adjustments 3-29 MEMO I n f o r m a t i o n P r o v i d e d b y :.
4 Display screen, heater, air conditioner, audio and phone systems Control panel buttons — with monochrome screen ....4 - 2 How to use the TRIP button .....................4 - 3 How to use the SETTING button .................4 - 5 button ...........
FM/AM/SA T radio with compact disc (CD) changer (T ype A and B) (if so equipped) ......... 4-56 CD care and cleaning .......................... 4-61 Steering wheel switch for audio control .......... 4-62 Rear audio controls (if so equipped) .........
WARNING ● Do not disassemble or modify this sys- tem. If you do, it may result in accidents, fire, or electrical shock. ● Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound. Continued use of the system may result in accident, fire or electric shock.
Reference symbols: TRIP button — This is a button on the control panel. By pressing this button you can select the item or perform this action. HOW TO USE THE TRIP BUTTON When the TRIP button is pressed, the following modes will display on the screen.
Average speed (MPH or km/h) The Average Speed mode shows the average speed since the last reset. T o calculate the aver- age speed, driving distance is divided by driving time. For approximately the first 30 seconds after a reset or reconnecting the battery cables, the display will show —.
In case of low tire pressure, a message “L OW PRESSURE” or “CHECK ALL TIRES” is dis- played on the screen: L OW PRESSURE — CHECK ALL TIRES. WARNING ● When a spare tire is mounted or a whee.
Language The language can be changed to “ENGLISH” or “FRANÇAIS” by pressing the TUNE button. MP3 display type (if so equipped) T o change how MP3 discs are displayed, press the TUNE button to select “DISC NUMBER” or “FOLDER NUMBER” . Disc number mode will display the file number in the disc.
1. TRIP button (P . 4-8) 2. BACK (previous) button (P . 4-7) 3. Joystick and ENTER button (P . 4-7) 4. brightness control button (P . 4-16) 5. SETTING button (P . 4-11) If you use the system with the engine not running (ignition ON or ACC) for a long time, it will use up all the battery power, and the engine will not start.
HOW TO USE THE TRIP BUTTON When the TRIP button is pressed, the following modes will display on the screen. W arning message (if any) → TRIP 1 → TRIP 2 → FUEL ECONOMY → MAINTENANCE → Audio o.
Resetting fuel economy The average fuel economy calculation can be reset to 0. Press the TRIP button repeatedly until the FUEL ECONOMY menu is shown, then ei- ther: ● Select the “Reset” key on screen by press- ing the ENTER button, or ● Press the TRIP button for more than approxi- mately 1.
Resetting the maintenance interval The ENGINE OIL and TIRE RO T A TION mainte- nance intervals can be reset to 0 miles (kilome- ters) . Select the “Reset” key using the joystick and press the ENTER button.
Tire pressure information T o display tire pressure information, press the TRIP button repeatedly until the MAINTENANCE screen is displayed. Select the “Tire Pressure” key using the joystick and press the ENTER but- ton. Pressure indication in ** psi on the screen indi- cates that the pressure is being measured.
Display settings Select the “Display” key and press the ENTER button. The DISPLA Y SETTINGS screen will ap- pear. Brightness/contrast/screen background: Select the “Brightness/Contrast/Screen Back- ground” key to adjust the brightness and contrast of the screen.
T o turn the screen on, ● Press the SETTING button and select the “Display” key and then select the “Display Off” key. Then set the screen to on by press- ing the ENTER button, or ● Hold t.
V ehicle electronic systems Select the “V ehicle Electronic Systems” key by using the joystick and pressing the ENTER but- ton. The VEHICLE ELECTRONIC S Y STEMS screen will be displayed. Y ou can set the following operating conditions by selecting the desired item using the joystick, then pressing the ENTER button.
NO TE: If you change the horn beep or the lamp flash feature with the keyfob, the mode will not be changed with the display. Use the keyfob to return to the previous mode and re-enable the display control. Auto re-lock time: Select to set the length of time before doors automatically re-lock.
Clock Adjusting the time: Select the “Hours” or “Minutes” key and move the joystick to the right or left to adjust the time. The time will change step by step. The new settings are automatically saved when you exit the setting screen by pressing the BACK or any other mode button.
1. ROUTE button* 2. DEST button* 3. MAP button* 4. BACK (previous) button (P . 4-18) 5. zoom out button* 6. Joystick and ENTER button (P . 4-17) 7. zoom in button* 8. VOICE button* 9. SETTING button (P . 4-22) 10. brightness control button (P . 4-28) 11.
HOW TO USE THE BACK BUTTON This button has two functions. ● Go back to the previous display (cancel) . If you press the BACK button during setup, the setup will be canceled and/or the display will return to the previous screen. ● Finish setup. In some screens pressing the BACK button ac- cepts the changes made during setup.
Fuel economy Press the TRIP button to display Average Fuel Economy and Distance T o Empty. Average fuel economy (MPG or L/100 km) The Average Fuel Economy is calculated based on fuel consumption since the last reset. The display is updated every 30 seconds and 1/3 mile (500 m) .
Changing the maintenance interval Select the “Engine Oil” or “Tire Rotation” key using the joystick and press the ENTER button to display the screen to change the maintenance interval. Select the “Maintenance Schedule” key using the joystick and move the joystick to right or left to set the maintenance interval.
● The ignition key is turned ON the next time the vehicle will be driven. T o return to the previous display after the MAIN- TENANCE NO TICE screen is displayed, press the BACK button. The MAINTENANCE NOTICE screen displays each time the key is turned ON until one of the following conditions are met: ● “Reset” key is selected.
HOW TO USE THE SETTING BUTTON When the SETTING button is pressed, the SET - TINGS screen will appear on the display . Y ou can select and/or adjust several functions, features and modes that are available for your vehicle. Move the joystick and press the ENTER button to select each item to be set.
Display off: Select the “Display Off” key. The indicator of the “Display Off” turns amber and the message above will be displayed briefly . When the audio, HV AC (Heater and air conditioner) , or any mode button on the control panel is operated, the dis- play turns on for that operation.
Any time audio information is shown on the main part of the screen, HV AC information will be displayed on the lower part of the screen. HV AC information will be shown even if “ Audio” is se- lected to be displayed on the lower part of the screen.
NO TE: If you change the horn beep or the lamp flash feature with the keyfob, the display screen will not show the current mode. Use the keyfob to return to the previous mode and re-enable the display screen control.
Y ou can select the language and unit using the joystick or pressing the ENTER button. The settings are automatically saved when you exit the menu by pressing the BACK button or any other mode button. Clock Adjusting the time: Select the “Hours” or “Minutes” key and move the joystick to the right or left to adjust the time.
Adjusting the time to the GPS: Select the “ Auto Adjust” key. The time will be reset to the GPS time. Selecting the time zone: 1. Select the “Select Time Zone” key . The TIME Z ONE screen will appear. 2. Select one of the following zones, depend- ing on the current location.
The GPS time (manual time) corresponding to the selected zone will be displayed. Pacific zone has been set as the initial (default) setting. Beep setting With this option ON, a beep will sound if any audio button is pressed. Navigation settings Refer to the separate Navigation System Own- er’s Manual for information regarding these set- tings.
They are indicated as reference distances to objects. The lines and colors in the display indi- cate distances from the back bumper line s A in the illustration. s 1 1.5 ft (0.5 m) red s 2 3 ft (1 m) yellow s 3 7 ft (2 m) green s 4 10 ft (3 m) green The vehicle clearance lines are wider than the actual clearance.
● Do not damage the camera as the monitor screen may be adversely affected. ● Do not use body wax on the camera window. Wipe off the wax with a clean cloth damp- ened with mild detergent diluted with water.
WARNING ● The air conditioner cooling function op- erates only when the engine is running. ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle.
— Air flows from defroster outlets T emperature control dial The temperature control dial allows you to adjust the temperature of the outlet air. T o lower the temperature, turn the dial to the left. T o increase the temperature, turn the dial to the right.
● T o quickly remove ice or fog from the win- dows, turn the fan control dial to the highest setting and the temperature control to the full HO T position. ● When the position is selected, the air conditioner automatically turns on (however, A/C will not appear on the display) if the outside temperature is more than 36°F (2°C) .
● For quick cooling when the outside tem- perature is high, push the button to the ON position ( shown on display) . Be sure to return the to the OFF po- sition for normal cooling ( shown on display) . Dehumidified heating This mode is used to heat and dehumidify the air.
WHA0644 WHA0645 Display screen, heater, air conditioner, audio and phone systems 4-35 Z REVIEW COPY— 2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X I n f o r m a t i o n P r .
WHA0646 WHA0647 4-36 Display screen, heater, air conditioner, audio and phone systems Z REVIEW COPY— 2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X I n f o r m a t i o n P r .
WHA0648 Display screen, heater, air conditioner, audio and phone systems 4-37 Z REVIEW COPY— 2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X I n f o r m a t i o n P r o v i d .
WHA0649 4-38 Display screen, heater, air conditioner, audio and phone systems Z REVIEW COPY— 2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X I n f o r m a t i o n P r o v i d .
WHA0650 Display screen, heater, air conditioner, audio and phone systems 4-39 Z REVIEW COPY— 2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X I n f o r m a t i o n P r o v i d .
1. Driver temperature control dial/ AUT O button 2. A/C ON/OFF button 3. Fan speed control (decrease) 4. Front window defroster button 5. System off button 6. Rear window defroster button 7. Fan speed control (increase) 8. Air recirculation button 9. Passenger temperature control dial/ DUAL button 10.
● The temperature of the passenger compart- ment will be maintained automatically. Air flow distribution, fan speed and A/C on/off are also controlled automatically . ● A visible mist may be seen coming from the ventilators in hot, humid conditions as the air is cooled rapidly .
The sunload sensor s 1 , located on the top center of the instrument panel, helps the system main- tain a constant temperature. Do not put anything on or around this sensor. Rear seat temperature and fan speed can be controlled from both the front seat overhead con- sole controls s A or the rear seat overhead con- sole controls s B .
CONTROLS Fan control dial The fan control dial turns the rear vent fan on and off, and controls fan speed. T emperature control dial The temperature control dial allows rear passen- gers to adjust the temperature of the outlet air.
Reception conditions will constantly change be- cause of vehicle movement. Buildings, terrain, signal distance and interference from other ve- hicles can work against ideal reception. De- scribed below are some of the factors that can affect your radio reception.
AUDIO OPERATION PRECAUTIONS Compact disc (CD) player CAUTION ● Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD changer/player. ● T rying to load a CD with the CD door closed could damage the CD and/or CD changer.
CHECK DISC: ● Confirm that the CD is inserted cor- rectly (the label side is facing up, etc .) . ● Confirm that the CD is not bent or warped and it is free of scratches. PRESS EJECT: This is an error due to excessive tem- perature inside the player.
● If there is a file in the top level of the disc, “ROO T” is displayed. ● The playback order is the order in which the files were written by the writing software.
Specification chart : Supported media CD, CD-R, CD-RW Supported file systems ISO9660 LEVEL1, ISO9660 LEVEL2, Apple ISO, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not supported. Supported versions* MP3 V ersion MPEG1, MPEG2, MPEG2.5 Sampling frequency 8 kHz - 48 kHz Bit rate 8 kbps - 320 kbps, VBR T ag information ID3 tag VER1.
T roubleshooting guide: Symptom Cause and Countermeasure Cannot play Check if the disc was inserted correctly. Check if the disc is scratched or dirty. Check if there is condensation inside the player. If there is, wait until the condensation is gone (about 1 hour) before using the player.
1. SEEK/TRACK button 2. PRESET A·B·C button 3. CD/DVD button 4. Station select (1 - 6) buttons 5. POWER/VOLUME control knob 6. REAR CTRL button 7. AUX button 8. TUNE/CA T button 9. DISP button 10. FM·AM/SA T (satellite) radio button* 11. SCAN/RPT button 12.
Audio main operation Power/V olume control: T urn the ignition key to ACC or ON, and then press the POWER/VOLUME control knob while the system is off to call up the mode (radio or CD) which was playing immediately before the system was turned off. T o turn the system off, press the POWER/VOLUME control knob.
T o change the default display mode press the AUDIO button to display mode and press the TUNE button to select the following display modes: Channel number ←→ Channel name ←→ Name ←→ Title. Once the display mode is selected press the AUDIO button again to store the setting.
3. The channel indicator will then come on and the sound will resume. Memorizing is now complete. 4. Other buttons can be set in the same man- ner. * SA T presets are only available on SA T equipped vehicles. If the battery cable is disconnected, or if the fuse opens, the radio memory will be canceled.
REAR CTRL: Pressing the REAR CTRL button turns the rear seat audio controller on. REAR CTRL ON will display . Pressing it again will turn the rear seat audio controller off. REAR CTRL OFF will display. If the vehicle is not equipped with a rear seat audio controller, the display will show “REAR A V N/A ” .
1. SEEK/TRACK button 2. PRESET A·B·C button 3. CD/DVD button 4. Station and CD select (1 - 6) buttons 5. POWER/VOLUME control knob 6. REAR CTRL button 7. AUX button 8. TUNE/FLDR·CA T button 9. DISP button 10. FM·AM/SA T (satellite) radio button* 11.
1. SEEK/TRACK button 2. PRESET A·B·C button 3. CD/DVD button 4. Station and CD select (1 - 6) buttons 5. POWER/VOLUME control knob 6. REAR CTRL button 7. AUX button 8. TUNE/FLDR·CA T button 9. DISP button 10. SCAN button 11. FM·AM/SA T (satellite) radio select button* 12.
No satellite radio reception is available and “NO SA T” is displayed when the SA T button is pressed unless optional satellite receiver and antenna are installed, and an XM T satellite radio service subscription is active. Satellite radio not available in Alaska, Hawaii and Guam.
Display satellite radio display mode (if so equipped) T o change the text displayed when listening to satellite radio (if so equipped) press the DISP button. The DISP button will scroll through the broadcast information as follows: Name ←→ Title ←→ Current display mode.
SCAN button is not pressed within 5 seconds, SCAN tuning moves to the next station. Station memory operations: 18 stations can be set for the FM, AM and SA T radio to the A , B and C preset button in any combination of AM, FM or SA T* stations. 1. Press the PRESET A·B·C button to change between storage banks.
TUNE/FLDR·CA T (Folder·Catalog) : While playing an MP3, press the TUNE/FLDR·CA T button or to scan through available folders. TUNE/FLDR·CA T (Fast Forward and Rewind) : When the TUNE/FLDR·CA T button is pressed for more than 1.
CD IN indicator: The slot numbers (1 – 6) will illuminate if CDs have been loaded into the changer in CD mode only . AUX (Auxiliary) button: The AUX jack is located on the CD player. The AUX audio input jack accepts any standard ana- log audio input such as from a portable cassette tape/CD player, MP3 player or a laptop com- puter.
1. V olume control switch 2. MODE select switch 3. POWER on/off switch 4. T uning switch 1. V olume control switch 2. Phone operation switch 3. POWER on and MODE select switch 4. T uning switch STEERING WHEEL SWITCH FOR AUDIO CONTROL The audio system can be operated using the controls on the steering wheel.
Next/Previous track (CD) : Push the tuning switch or for less than 1.5 seconds to return to the beginning of the present track or skip to the next track. Push several times to skip back or skip through tracks. This system searches for the blank intervals be- tween selections.
REAR AUDIO CONTROLS (if so equipped) Press the REAR CTRL button on the front radio control panel to turn the rear controls on. Press the button again to turn the rear controls off. The headphones symbol illuminates on the front display when the rear audio controls are on.
ANTENNA Window antenna The antenna pattern is printed inside the rear passenger and driver side windows. CAUTION ● Do not place metalized film near the rear driver or passenger side window glass or attach any metal parts to it. This may cause poor reception or noise.
1. EJECT button 2. DVD slot 3. ENTER button 4. POWER on/off button 5. MODE button 6. Input jacks 7. ST OP button 8. PLA Y/P AUSE button 9. MENU button 10. DISPLA Y button 11. NA VIGA TION keys DIGITAL VIDEO DISC (DVD) PLAYER CONTROLS Refer to “Playing a digital video disc (DVD)” later in this section for the function of each button.
6. DISPLA Y button 7. MODE button 8. SUBTITLE button 9. AUDIO button 10. ANGLE button 11. CLEAR button 12. P AUSE button 13. PLA Y button 14. F AST FORW ARD/F AST REVERSE button 15.
Headphones Power ON/OFF: Press the power button to turn the headphones on or off. V olume control: T urn the volume control knob to adjust the vol- ume. The headphones will automatically be turned off in 30 seconds if there is no sound during that period.
Pressing the button on the front controls turns the rear speakers on and off. It is possible to operate the DVD player by remote control. Headphones are a wireless type and no cables are necessary . Y ou can use them in almost all the ranges in the rear seat.
button is pressed again, it will resume at the stored disc track and time position. If the ST OP button is pressed again when the player is already in Stop mode, it will reinitialize the pointer to the beginning of the disc.
TITLE (Remote control only) : Press TITLE button to return the DVD media to the “title” of the DVD. Press TITLE button again to return to the previous stop point and play . BACK (Remote control only) : Press the BACK button to exit the current active menu and return to the previous menu.
Do not attempt to use the system in extreme temperature conditions [below -4°F (-20°C) or above 158°F (70°C)] Do not attempt to operate the system in extreme humidity conditions (less than 10% or more than 75%) . HOW TO HANDLE THE DVD CAUTION ● Handle a DVD by its edges.
DVD player operation precautions Do not use the following DVDs as they may cause the DVD player to malfunction: ● 3.1 in (8 cm) disc s with an adapter. ● DVDs with a region code other than “1” . The region code s A is displayed in a small symbol printed on the top of the DVD s B .
Remote control and headphones battery replacement Replace the battery as follows: 1. Open the lid. 2. Replace batteries with new ones. ● Size AA (remote control) ● Size AAA (headphones) Make sure that the and ends on the batteries match the markings inside the compartment.
When installing a CB, ham radio or car phone in your NISSAN, be sure to observe the following precautions, otherwise the new equipment may adversely affect the engine control system and other electronic parts. WARNING ● A cellular telephone should not be used while driving so full attention may be given to vehicle operation.
Y our NISSAN is equipped with the Bluetooth T Hands-Free Phone System. If you have an ap- proved Bluetooth T enabled cellular phone, you can set up the wireless connection between your cellular phone and the in-vehicle phone module.
– Y our cellular phone is locked to prevent it from being dialed. ● When the radio wave condition is not ideal or ambient sound is too loud, it may be difficult to hear the other person’s voice dur- ing a call.
Giving voice commands T o operate NISSAN Voice Recognition, press and release the button located on the steering wheel. The light on the overhead con- sole flashes to signal you have entered a voice recognition (VR) session. After the tone sounds, speak a command.
CONTROL BUTTONS The control buttons for the Bluetooth T Hands- Free Phone System are located on the steering wheel. PHONE/SEND Press the button to initiate a VR session or answer an incoming call. Y ou can also use the button to skip through system feedback and to enter commands during a call.
Pairing procedure NO TE: The pairing procedure must be performed when the vehicle is stationary. If the vehicle starts moving during the procedure, the procedure will be cancelled. Main Menu “Setup” s A “Pair phone” s B “New phone” s C Initiate from handset s D Name phone s E Assign priority s F Choose ringtone s G 1.
3. Say the number you wish to call s B . For example, 555-1212 can be said as “five five five one two one two.” See “How to say numbers” earlier in this section for more information. 4. When you have finished speaking the phone number, the system repeats it back and an- nounces the available commands.
When prompted by the system, say the name of the phone book entry you wish to call. The system acknowledges the name. If there are multiple locations associated with the name, the system asks you to choose the loca- tion. Once you have confirmed the name and location, the system begins the call.
“Phone book” NO TE: Phone book commands are not available when the vehicle is moving. Main Menu “Phone Book” “New Entry” s A “Edit” s B “Delete” s C 9 List Names” s D The Phone Book stores up to 40 names for each phone paired with the system.
The system acknowledges the location. The system will ask you to say a phone number or to transfer a phone number stored in the cellular phone’s memory . Enter a phone number by voice command: For example, say: “five five five one two one two. ” See “How to say numbers” earlier in this section for more information.
“Play” s B The system plays back all the memos in the order of newest to oldest. The system ends the VR session. If there are no memos recorded, the system an- nounces “No messages to play.” The system ends the VR session. “Delete” s C The Delete command erases all memos.
“Change priority” s D Use the Change Priority command to change the priority level of the active phone. The priority level determines which phone is ac- tive when more than one paired Bluetooth T phone is in the vehicle. The system states the priority level of the active phone and asks for a new priority level (1, 2, 3, 4, 5) .
T raining procedure The procedure for training a voice is as follows. 1. Position the vehicle in a reasonably quiet outdoor location. 2. Sit in the driver’s seat with the engine run- ning, the parking brake on, and the transmis- sion in P (Park) . 3.
● dial eight three zero five one ● Home ● four three pause two nine pause zero ● delete redial number ● phone book list names ● call eight oh five four one ● Correction ● setup change .
T ROUBLESHOOTING GUIDE The system should respond correctly to all voice commands without difficulty . If problems are en- countered, try the following solutions. Where the solutions are listed by number, try each solution in turn, starting with number 1, until the problem is resolved.
4-90 Display screen, heater, air conditioner, audio and phone systems MEMO I n f o r m a t i o n P r o v i d e d b y :.
5 Starting and driving Precautions when starting and driving ................5 - 2 Exhaust gas (carbon monoxide) ..................5 - 2 Three-way catalyst ..............................5 - 2 Tire Pressure Monitoring System (TPMS) ..........5 - 3 Avoiding collision and rollover .
WARNING ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle.
CAUTION ● Do not use leaded gasoline. Deposits from leaded gasoline will seriously re- duce the three-way catalyst’s ability to help reduce exhaust pollutants. ● Keep your engine tuned up. Malfunc- tions in the ignition, fuel injection, or electrical systems can cause overrich fuel flow into the three-way catalyst, causing it to overheat.
● The low tire pressure warning light does not automatically turn off when the tire pressure is adjusted. After the tire is inflated to the recommended pressure, the vehicle must be driven at speeds above 16 MPH (25 km/h) to activate the TPMS and turn off the low tire pressure warning light.
Some examples are: – Facilities or electric devices using similar radio frequencies are near the vehicle. – If a transmitter set to similar frequencies is being used in or near the vehicle. – If a computer (or similar equipment) or a DC/AC converter is being used in or near the vehicle.
WARNING Never remove or turn the key to the LOCK position while driving. The steering wheel will lock. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury.
K EY POSITIONS L OCK: Normal parking position (0) OFF: (Not used) (1) ACC: (Accessories) (2) This position activates electrical accessories such as the radio when the engine is not running. ON: Normal operating position (3) This position turns on the ignition system and the electrical accessories.
1. Apply the parking brake. 2. Move the shift selector lever to P (Park) or N (Neutral) . P (Park) is recommended. The shift selector lever cannot be moved out of P (Park) and into any of the other gear positions if the ignition key is turned to the OFF position or if the key is removed from the ignition switch.
The recommended operating procedures for this transmission are shown on the following pages. Follow these procedures for maximum vehicle performance and driving enjoyment. Starting the vehicle 1. After starting the engine, fully depress the foot brake pedal before moving the shift selector lever out of the P (Park) position.
4. Move the shift selector lever to P (Park) or N (Neutral) to restart the vehicle (P is pre- ferred) . Move the shift selector lever to P (Park) to park the vehicle and turn the igni- tion key to the L OCK position to remove the key . P (Park) : CAUTION Use the P (Park) position only when the vehicle is completely stopped.
T o push the shift lock release, complete the fol- lowing procedure: 1. T urn the ignition key to the L OCK position and remove the key 2. Apply the parking brake. 3. Remove the shift lock release cover as shown. 4. Insert a small screwdriver in the shift lock release slot and push down.
OFF: For driving up and down long slopes where engine braking is nec- essary push the Overdrive switch once. The O/D OFF indicator light in the instrument panel comes on at this time. When cruising at a low speed or climbing a gentle slope, you may feel uncomfortable shift shocks as the transmission shifts into and out of Overdrive repeatedly .
1. ACCEL/RES switch 2. COAST/SET switch 3. CANCEL switch 4. ON·OFF switch PRECAUTIONS ON CRUISE CONTROL ● If the cruise control system malfunctions, it cancels automatically. The SET indicator light in the instrument panel then blinks to warn the driver.
● the vehicle slows down more than 8 MPH (13 km/h) below the set speed. ● you move the shift selector lever to N (Neu- tral) . T o reset at a faster cruising speed, use one of the following three methods. ● Depress the accelerator pedal. When the vehicle attains the desired speed, push and release the COAST/SET switch.
● Accelerate slowly and smoothly. Maintain cruising speeds with a constant accelerator position. ● Drive at moderate speeds on the highway. Driving at high speed lowers fuel economy . ● Avoid unnecessary stopping and braking. Maintain a safe distance behind other ve- hicles.
WARNING ● Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire. ● Safe parking procedures require that both the parking brake be set and the transmission placed into P (Park) .
The power assisted steering uses a hydraulic pump, driven by the engine, to assist steering. If the engine stops or the drive belt breaks, you will still have control of the vehicle. However, much greater steering effort is needed, especially in sharp turns and at low speeds.
This procedure is described in the vehicle service manual and can be performed by a NISSAN dealer. ANTI-LOCK BRAKING SYSTEM (ABS) WARNING ● The Anti-lock Braking System (ABS) is a sophisticated device, but it cannot pre- vent accidents resulting from careless or dangerous driving techniques.
pedal. This is normal and does not indicate a malfunction. If the computer senses a malfunc- tion, it switches the ABS off and illuminates the ABS warning light on the instrument panel. The brake system then operates normally, but without anti-lock assistance.
● When driving on extremely inclined sur- faces such as higher banked corners, the T raction Control System may not operate properly and the indica- tor light may come on.
● If brake related parts such as brake pads, rotors and calipers are not stan- dard equipment or are extremely dete- riorated, the V ehicle Dynamic Control system may not operate properly and the V ehicle Dynamic Control off indica- tor light may come on.
● The system is designed as an aid to the driver in detecting large stationary ob- jects to help avoid damaging the ve- hicle. The system will not detect small objects below the bumper, and may not detect objects close to the bumper or on the ground.
DRAINING OF COOLANT WATER If the vehicle is to be left outside without anti- freeze, drain the cooling system, including the engine block. Refill before operating the vehicle. For details, see “Changing engine coolant” in the “Maintenance and do-it-yourself” section of this manual.
ENGINE BLOCK HEATER (if so equipped) WARNING ● Do not use your engine block heater with an ungrounded electrical system or a 2-pronged adapter. Y ou can be se- riously injured by an electrical shock if you use an ungrounded connection. ● Disconnect and properly store the en- gine block heater cord before starting the engine.
6 In case of emergency Flat tire ...........................................6 - 2 Tire Pressure Monitoring System (TPMS) ..........6 - 2 Changing a flat tire .............................6 - 2 Jump starting .....................................6 - 7 Push starting .
TIRE PRESSURE MONITORING SYSTEM (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS) . It monitors tire pres- sure of all tires except the spare. When the low tire pressure warning light is lit, one or more of your tires is significantly under-inflated.
WARNING ● Make sure the parking brake is securely applied and the automatic transmission is shifted into P (Park) . ● Never change tires when the vehicle is on a slope, ice or slippery areas. This is hazardous. ● Never change tires if oncoming traffic is close to your vehicle.
3. Stow the center tray table (if so equipped) . 4. Move both front seats as forward as pos- sible. 5. Lift up the floor carpeting s 1 . Remove the spare tire cover s 2 and jack tool kit. 6. T urn the retainer counterclockwise and re- move the spare tire.
● Use the correct jack -up points. Never use any other part of the vehicle for jack support. ● Never jack up the vehicle more than necessary. ● Never use blocks on or under the jack. ● Do not start or run the engine while vehicle is on the jack.
Installing the spare tire The spare tire is designed for emergency use. See specific instructions under the heading “ Wheels and tires” in the “Mainte- nance and do-it-yourself” section of this manual. 1. Clean any mud or dirt from the surface be- tween the wheel and hub.
● The spare tire is designed for emer- gency use. See specific instructions un- der the heading “ Wheels and tires” in the “Maintenance and do-it-yourself” section of this manual. T o start your engine with a booster battery, the instructions and precautions below must be fol- lowed.
WARNING Always follow the instructions below. Failure to do so could result in damage to the charging system and cause personal injury. 1. If the booster battery is in another vehicle, position the two vehicles to bring their bat- teries near each other.
CAUTION Automatic transmission models cannot be push-started or tow-started. Attempt- ing to do so may cause transmission damage. If your vehicle is overheating (indicated by an extremely high temperature gauge reading) , or if you feel a lack of engine power, detect abnormal noise, etc.
6. After the engine cools down, check the cool- ant level in the engine coolant reservoir tank with the engine running. Add coolant to the engine coolant reservoir tank if necessary. Have your vehicle repaired at a NISSAN dealer. When towing your vehicle, all State (Provincial in Canada) and local regulations for towing must be followed.
T OWING RECOMMENDED BY NISSAN NISSAN recommends that your vehicle be towed with the driving (front) wheels off the ground or place the vehicle on a flat bed truck as illustrated.
V EHICLE RECOVERY (freeing a stuck vehicle) Front WARNING ● Stand clear of a stuck vehicle. ● Do not spin your tires at high speed. This could cause them to explode and result in serious injury. Parts of your vehicle could also overheat and be damaged.
7 Appearance and care Cleaning exterior ..................................7 - 2 W ashing ......................................7 - 2 W axing ........................................7 - 2 Removing spots ................................7 - 3 Underbody .
In order to maintain the appearance of your ve- hicle, it is important to take proper care of it. T o protect the paint surfaces, please wash your vehicle as soon as you can: ● after a rainfall to prevent possible damage from acid rain. ● after driving on coastal roads.
REMOVING SPOTS Remove tar and oil spots, industrial dust, insects, and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining. Special cleaning products are available at a NISSAN dealer or any automotive accessory store.
Occasionally remove loose dust from the interior trim, plastic parts and seats using a vacuum cleaner or soft bristled brush. Wipe the vinyl and leather surfaces with a clean, soft cloth damp- ened in mild soap solution, then wipe clean with a dry , soft cloth.
SEAT BELTS The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solution. Allow the belts to dry completely in the shade before using them. See “Seat belt maintenance” in the “Safety – Seats, seat belts and supplemen- tal restraint system” section of this manual.
CAUTION ● NEVER remove dirt, sand or other de- bris from the passenger compartment by washing it out with a hose. Remove dirt with a vacuum cleaner or broom. ● Never allow water or other liquids to come in contact with electronic compo- nents inside the vehicle as this may damage them.
8 Maintenance and do-it-yourself Maintenance requirements ..........................8 - 2 General maintenance ..............................8 - 2 Explanation of general maintenance items .........8 - 2 Maintenance precautions .........................
Y our new NISSAN has been designed to have minimum maintenance requirements with long service intervals to save you both time and money . However, some day-to-day and regular maintenance is essential to maintain your NIS- SAN’s good mechanical condition, as well as its emission and engine performance.
When driving in areas using road salt or other corrosive materials, check lubrication frequently . Lights* Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely.
Steering wheel Check for changes in the steer- ing system, such as excessive freeplay, hard steering or strange noises. Warning lights and chimes Make sure all warning lights and chimes are operating properly. Windshield wiper and washer* Check that the wipers and washer operate properly and that the wipers do not streak.
When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle.
1. P ower steering fluid reservoir 2. Engine oil filler cap 3. Air cleaner 4. Brake fluid reservoir 5. Battery 6. Fuse/fusible link box 7. T ransmission dipstick 8. Engine oil dipstick 9. Radiator cap 10. Drive belt location 11. Fuse block 12. Windshield washer fluid reservoir 13.
The engine cooling system is filled at the factory with Genuine NISSAN Long Life Antifreeze/Coolant to provide year-round anti- freeze and coolant protection. The anti-freeze solution contains rust and corrosion inhibitors. Additional engine cooling system additives are not necessary .
CHANGING ENGINE COOLANT A NISSAN dealer can change the engine coolant. The service procedure can be found in the NISSAN Service Manual. Improper servicing can result in reduced heater performance and engine overheat- ing. WARNING ● T o avoid the danger of being scalded, never change the coolant when the en- gine is hot.
CAUTION Oil level should be checked regularly. Op- erating the engine with an insufficient amount of oil can damage the engine, and such damage is not covered by warranty. CHANGING ENGINE OIL 1. Park the vehicle on a level surface and apply the parking brake.
7. Refill engine with recommended oil through the oil filler opening, then install the oil filler cap securely . See “Capacities and recommended fuel/lubricants” in the “T echnical and con- sumer information” section of this manual for drain and refill capacity .
When checking or replacement is required, we recommend your NISSAN dealer for servicing. CAUTION ● Use only Genuine NISSAN Matic K A TF . Do not mix with other fluids.
BRAKE FLUID Check the brake fluid level in the reservoir. If the fluid level is below the MIN line or the brake warning light comes on, add Genuine NISSAN Super Heavy Duty Brake Fluid or equivalent DOT 3 fluid up to the MAX line. If fluid must be added frequently , the system should be checked by a NISSAN dealer.
● K eep the battery surface clean and dry. Clean the battery with a solution of baking soda and water. ● Make certain the terminal connections are clean and securely tightened. ● If the vehicle is not to be used for 30 days or longer, disconnect the negative (-) battery terminal cable to prevent discharge.
2. Check the fluid level in each cell. If it is necessary to add fluid, add only distilled water to bring the level up to the bottom of the filler opening. Do not overfill. V ehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level.
2. Have the belt checked regularly for condi- tion and tension in accordance with the maintenance schedule found in the “NISSAN Service and Maintenance Guide” .
The air cleaner filter should not be cleaned and reused. Replace it according to the maintenance log shown in the “NISSAN Service and Mainte- nance Guide.” When replacing the filter, wipe the inside of the air cleaner filter housing and the cover with a damp cloth.
CLEANING If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running, wax or other material may be on the blade or windshield. Clean the outside of the windshield with a washer solution or a mild detergent.
Be careful not to let anything get into the washer nozzle s A . This may cause clogging or improper windshield washer operation. If something gets into the nozzle, remove it with a needle or small pin s B .
Rear window wiper blade s 1 Lift the wiper arm away from the rear win- dow . s 2 Push the wiper blade in and pivot until the blade becomes free. s 3 Insert a new blade onto the wiper arm and snap into place.
If the brakes do not operate properly , have the brakes checked by a NISSAN dealer. SELF-ADJUSTING BRAKES Y our vehicle is equipped with self-adjusting brakes.
3. Remove the fuse box cover by pushing the tab and lifting the cover up. 4. Remove the fuse with the fuse puller. The fuse puller is located in the center of the fuse block in the passenger compartment. 5. If the fuse is open s A , replace it with a new fuse s B .
2. Pull the sunglasses holder down to open s 1 . 3. Pull up on the sunglasses holder s 2 and remove to expose the fuse panel. 4. Remove the fuse with the fuse puller. 5. If the fuse is open s A , replace it with an equivalent good fuse s B . 6. Push the fuse box cover to install.
CAUTION Be careful not to allow children to swallow the battery and removed parts. K EYFOB Replace the battery in the keyfob as follows: s 1 Open the lid using a coin s A . s 2 Remove the battery s B . s 3 Install a new battery s C with the “+” facing down.
● Do not touch the internal circuit and electric terminals as it could cause a malfunction. Recommended battery: CR2025 or equivalent. s 4 Close the lid securely . 5. Press the button, then the button two or three times to check the key- fob operation.
● Use the same number and wattage as originally installed: Low beam: Wattage: 51 Bulb no.: 9006* High beam: Wattage: 60 Bulb no.: 9005* *: Always check with the Parts Depart- ment at a NISSAN dealer for the latest parts information.
4. Rotate the bulb counterclockwise and re- move. 5. Remove by pulling it straight out of the fog light assembly . Do not shake or rotate the bulb when removing it. Do not touch the glass envelope. 6. Install in the reverse order of removal. EXTERIOR AND INTERIOR LIGHTS Item W attage (W) Bulb No.
1. Room/map light 2. Front personal lights 3. Step light 4. Puddle lamp 5. High-mounted stoplight 6. Cargo light 7. License plate light 8. Rear combination light 9. Headlight assembly 10. Fog light Replacement procedures All other lights are either type A , B, C or D.
Use a cloth s 1 to protect the housing. Use a cloth s 1 to protect the housing. Use a cloth s 1 to protect the housing. Room/map lights LDI0517 Personal lights – T ype A LDI0364 Personal lights – .
Use a cloth s 1 to protect the housing. Use a cloth s 1 to protect the housing. Step light LDI0341 Cargo light LDI0366 Rear combination light LDI0367 Maintenance and do-it-yourself 8-29 Z REVIEW COPY.
If you have a flat tire, see the “In case of emergency” section of this manual. TIRE PRESSURE Tire Pressure Monitoring System (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS) . It monitors tire pressure of all tires except the spare.
WARNING ● Improperly inflated tires can fail suddenly and cause an accident. ● The Gross V ehicle Weight Rating (GVWR) is located on the F .M .V .S.S./C .M .V .S.S. certifica- tion label. The vehicle weight ca- pacity is indicated on the Tire and Loading Information label (if so equipped) .
Tire and loading information label s 1 Seating capacity: The maximum num- ber of occupants that can be seated in the vehicle. s 2 V ehicle load limit: See loading infor- mation in the “T echnical and con- sumer information” section. s 3 Original tire size: The size of the tires originally installed on the vehicle at the factory .
Checking tire pressure 1. Remove the valve stem cap from the tire. 2. Press the pressure gauge squarely onto the valve stem. Do not press too hard or force the valve stem side- ways, or air will escape. If the hissing sound of air escaping from the tire is heard while checking the pressure, reposition the gauge to eliminate this leakage.
s 1 Tire size (example: P215/65R15 95H) 1. P: The 9 P 9 indicates the tire is de- signed for passenger vehicles (not all tires have this information) . 2. Three-digit number (215): This num- ber gives the width in millimeters of the tire from sidewall edge to side- wall edge.
s 2 TIN (Tire Identification Number) for a new tire (example: DO T XX XX XXX XXXX) 1. DO T : Abbreviation for the 9 Depart- ment Of T ransportation. 9 The symbol can be placed above, below or to the left or right of Tire Identification Num- ber. 2. T wo-digit code: Manufacturer’s identification mark 3.
s 7 The word “radial” The word “radial” is shown if the tire has radial structure. s 8 Manufacturer or brand name Manufacturer or brand name is shown.
For additional traction on icy roads, studded tires may be used. However, some U.S. states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires.
Wheel nut tightening torque: 83 ft-lb (112 N·m) The wheel nuts must be kept tight- ened to specifications at all times. It is recommended that wheel nuts be tightened to specification at each tire rotation interval. WARNING ● After rotating the tires, check and adjust the tire pressure.
Replacing wheels and tires When replacing a tire, use the same size, tread design, speed rating and load carrying capacity as originally equipped. Recommended types and sizes are shown in “Wheels and tires” in the “T echnical and consumer information” section of this manual.
Care of wheels ● W ash the wheels when washing the vehicle to maintain their appearance. ● Clean the inner side of the wheels when the wheel is changed or the underside of the vehicle is washed. ● Do not use abrasive cleaners when washing the wheels.
9 T echnical and consumer information Capacities and recommended fuel/lubricants .........9 - 2 Fuel recommendation ...........................9 - 3 Engine oil and oil filter recommendations ..........9 - 5 Air conditioner system refrigerant and oil recommendations .
The following are approximate capacities. The actual refill capacities may be slightly different. When refilling, follow the procedure described in the “Maintenance and do-it-yourself” section to determine the proper refill capacity. Capacity (Approximate) Recommended Fluids and Lubricants US measure Imp measure Liter Fuel 20 gal 16-5/8 gal 75.
FUEL RECOMMENDATION NISSAN recommends the use of unleaded pre- mium gasoline with an octane rating of at least 91 AKI (Anti-Knock Index) number (Research oc- tane number 96) .
E–85 fuel E-85 fuel is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. E-85 can only be used in a Flexible Fuel V ehicle (FFV) .
ENGINE OIL AND OIL FILTER RECOMMENDATIONS Selecting the correct oil It is essential to choose the correct grade, quality and viscosity engine oil to ensure satisfactory engine life and performance. See 9 Capacities and recommended fuel/lubricants 9 earlier in this section.
Y our engine was filled with a high-quality engine oil when it was built. Y ou do not have to change the oil before the first recommended change interval.
ENGINE Model VQ35DE T ype Gasoline, 4-cycle, DOHC Cylinder arrangement 6-cylinder, V-block, Slanted at 60° Bore x Stroke in (mm) 3.760 x 3.205 (95.5 x 81.4) Displacement cu in (cm 3 ) 213.5 (3,498) Firing order 1–2–3–4–5–6 Idle speed No adjustment is necessary.
WHEELS AND TIRES Wheels 16 x 6.5JJ 17 x 6.5JJ Tires P225/65R16 P225/60R17 Spare tire T135/80*16 Speed rating 16” H 17” H *: “R” or “D” depending on tire manufacturer DIMENSIONS AND WEIGHTS Overall length in (mm) 204.13(5,185) Overall width in (mm) 78.
When planning to drive your NISSAN ve- hicle in another country, you should first find out if the fuel available is suitable for your vehi- cle’s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline.
ENGINE SERIAL NUMBER The number is stamped on the engine as shown. F .M.V .S.S./C.M.V .S.S. CERTIFICATION LABEL The Federal/Canadian Motor V ehicle Safety Standard (F.
TIRE AND LOADING INFORMATION LABEL The cold tire pressure is shown on the Tire and Loading Information label. The label is located as shown. AIR CONDITIONER SPECIFICATION LABEL The air conditioner specification label is affixed to the underside of the hood as shown.
Use the following steps to mount the front license plate: Before mounting the license plate, confirm that the following parts are enclosed in the plastic bag: ● License plate bracket ● License plate bracket screws x 2 ● License plate screws x 2 ● Screw grommets x 2 1.
● Vehicle Capacity Weight, Load limit, T otal load capacity - maximum total weight limit specified of the load (passengers and cargo) for the ve- hicle.
Steps for determining correct load limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be trans- ferred to your vehicle.
WARNING Overloading or improper loading of a trailer and its cargo can adversely affect vehicle handling, braking and perfor- mance and may lead to accidents. CAUTION ● Do not tow a trailer or haul a heavy load for the first 500 miles (800 km) . Y our engine, axle or other parts could be damaged.
T emperature conditions can also affect towing. For example, towing a heavy trailer in high outside temperatures on graded roads can affect engine performance and cause overheating. The engine protection mode, which helps reduce the chance of engine damage, could activate and automati- cally decrease engine power.
T owing capacities are calculated assuming a base vehicle with driver and any options required to achieve the rating. Additional passengers, cargo and/or optional equipment, such as the trailer hitch, will add weight to the vehicle and reduce your vehicle’s maximum towing capacity and trailer tongue load.
The available towing capacity may be less than the maximum towing capacity due to the passen- ger and cargo load in the vehicle. Remember to keep trailer tongue weight be- tween 10 - 15% of the trailer weight. If the tongue load becomes excessive, rearrange the cargo to obtain the proper tongue load.
Class II hitch Class II trailer hitch equipment (receiver, ball mount and hitch ball) can be used to tow trailers of a maximum weight of 3,500 lb (1,510 kg) . CAUTION ● Do not use axle-mounted hitches. ● The hitch should not be attached to or affect the operation of the impact- absorbing bumper.
WARNING Never connect a trailer brake system di- rectly to the vehicle brake system. Pre-towing tips ● Be certain your vehicle maintains a level position when a loaded and/or unloaded trailer is hitched.
4. Release the parking brake. 5. Drive slowly until the vehicle and trailer are clear from the blocks. 6. Apply and hold the brake pedal. 7. Have someone retrieve and store the blocks. ● When going down a hill, shift into a lower gear and use the engine braking effect.
● Some states or provinces have specific regulations and speed limits for vehicles that are towing trailers. Obey the local speed limits. ● Check your hitch, trailer wiring harness con- nections, and trailer wheel lug nuts after 50 miles (80 km) of travel and at every break.
WARNING The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristic s.
If you believe that your vehicle has a de- fect which could cause a crash or could cause injury or death, you should immedi- ately inform the National Highway T raffic Safety Administration (NHTSA) in addi- tion to notifying NISSAN.
8. Stop the vehicle. Place the transmission se- lector lever in the P (Park) or N (Neutral) position. 9. T urn the engine off. 10. Repeat step s1-8a t least one more time. If steps 1 through 7 are interrupted, repeat the preceding step. Any safe driving mode is accept- able between steps.
A genuine NISSAN Service Manual is the best source of service and repair information for your vehicle. Filled with wiring diagrams, illustrations and step-by-step diagnostic and adjustment pro- cedures, this manual is the same one used by the factory-trained technicians working at NISSAN dealerships.
It’s your right! If you should need further information visit us at: www.nissanusa.com (for U.S. customers) or www.nissan.ca (for Canadian customers) .
10 Index A Active Head Restraint ............. .1-7 Adjusting pedal position ........... .3-21 Air bag (See supplemental restraint system) .................... .1-52 Air bag system Front (See supplemental front impact air bag system) ................ .
CD changer (See audio system) ....... .4-59 CD player (See audio system) ........ .4-53 Child restraint with top tether strap ..... .1-30 Child restraints ...... .1-17, 1-18, 1-26, 1-28 Precautions on child restraints ........... .1-26, 1-41, 1-47 T op tether strap anchor point locations .
F Flashers (See hazard warning flasher switch) ..... .2-23 Flat tire ..................... .6-2 Floor mat positioning aid ............ .7-4 Fluid Brake fluid ................. .8-11 Capacities and recommended fuel/lubricants ................ .9-2 Engine coolant .
Keyless entry system (See remote keyless entry system) ...... .3-9 L Labels Air conditioner specification label .... .9-11 C.M.V .S.S. certification label ....... .9-10 Emission control information label .... .9-10 Engine serial number ........... .9-10 F .
Overheat If your vehicle overheats .......... .6-9 Owner’s manual order form ......... .9-27 Owner’s manual/service manual order information ................... .9-27 P Parking Parking brake operation ......... .5-12 Parking/parking on hills .....
Security indicator light ............ .2-12 Security system (NISSAN vehicle immobilizer system) , engine start ........ .2-15, 3-2, 5-7 Self-adjusting brakes ............. .8-20 Service manual order form .......... .9-27 Servicing air conditioner ....
Tire rotation maintenance reminder .............. .4-4, 4-11, 4-21 T op tether strap child restraint ........ .1-30 T owing Flat towing ................. .9-23 T ow truck towing ............. .6-10 T owing load/specification ........ .9-19 T railer towing .
MEMO I n f o r m a t i o n P r o v i d e d b y :.
MEMO I n f o r m a t i o n P r o v i d e d b y :.
MEMO I n f o r m a t i o n P r o v i d e d b y :.
MEMO I n f o r m a t i o n P r o v i d e d b y :.
MEMO I n f o r m a t i o n P r o v i d e d b y :.
RECOMMENDED FUEL: Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) num- ber (Research octane number 91) . NISSAN recommends the use of premium un- leaded gasoline with an octane rating of at least 91 AKI number (Research octane number 96) .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Nissan Quest (2008) c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Nissan Quest (2008) - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Nissan Quest (2008), vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Nissan Quest (2008) va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Nissan Quest (2008), mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Nissan Quest (2008).
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Nissan Quest (2008). Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Nissan Quest (2008) ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
