Manuel d'utilisation / d'entretien du produit Model 34 du fabricant Assa
Aller à la page of 25
© Copyright, 2003, all rights reserved • Securitron Magnalock Corp., 550 Vista Blvd., Sparks NV 89434, USA Tel: (775) 355-5625 • (800) MAGLOCK • Fax: (775) 355-5636 • Website: www.securitron.com An ASSA ABLOY Group company PN# 500-10420 Rev. A.
Rev. A.5, 8/03 SECTION 3. ELECTRICAL INSTALLATION -----------------------------------------------Page 14 SECTION 3.1 GENERAL ELECTRICAL CHARACTERISTICS -----------------------Page 14 This section explains technically the Magnalock's electrical characteristics as a load and is for reference.
Rev. A.5, 8/03 Use of the Magnalock (or any lock) can lead to an unsafe condition within the building if it is controlled in a manner that improperly restricts passage through certain doors. The most important area of concern is to insure that building evacuation is not impeded in the event of a fire or other emergency condition.
Rev. A.5, 8/03 Page- 1 SECURITRON 32, 34, 62 AND 82 SERIES MAGNALOCK INSTALLATION INSTRUCTIONS 1. DESCRIPTION Securitron’s Magnalock family repres ents the state of the art in electric locking. Three different size models are available: The Model 32 and Model 34 series with a holding force of 600 lbs.
Rev. A.5, 8/03 Page- 2 FIG. 1: STEPS IN MOUNTING THE STRIKE Step four is to insert roll pins furnished with the stri ke. The pins are hammered into the strike but be careful not to hit them too hard as it is possible to raise dents on the strike surface by over driving the pins which degrades strike flatness and therefore holding force.
Rev. A.5, 8/03 Page- 3 FIG. 2: STANDARD MAGNET DIMENSIONS AND ASSEMBLY Blind Nut PN# BN-250 or PN# BN-6MM (Metric) (Pack of 40 with tool) Gold Washer PN# FW-1 (Pack of 24) Tamper Cap PN# FC-1 (Pack of 24) Length Width Depth 32 8" 1.88 1.5 (mm) 203 47.
Rev. A.5, 8/03 Page- 4 FIG. 3: STRIKE DIMENSIONS AND ASSEMBLY Once a solid flat surface has been prepared for the magnet, it must be positioned so that its face is parallel and centered to the strike plat e. When the magnet ha s been experimentally positioned this way, it's ready for mounting.
Rev. A.5, 8/03 Page- 5 FIG. 4: COLLAPSING THE BLIND NUTS HEADER TOOL BLIND NU T NUT AS SHOWN PRESS IN BLI ND COLLAPSES WHEN CAP SCREW IS T UR N ED W IT H A LL E N W RE NC H WH IL E TO O L IS HE LD FA .
Rev. A.5, 8/03 Page- 6 sheet rock do not constitute a secure mounting s ubstrate). Note that when the roll pin bushings are used, they protrude through the Z bracket and interfere with the Z bracket cover. If a Senstat lock is being employed, the roll pin bushings must be used to provide insulation.
Rev. A.5, 8/03 Page- 7 FIG. 7: F MAGNALOCK MOUNTING Sex Bolt Drill 1/2" (12.7mm) hole Washer Stack Header T-Nut requires 3/8" (9.5mm) Dia hole in bracket and accepts strike mounting screw Roll pin plastic bushing require 1/2" (12.7mm) holes and must be shortened to work in Z bracket.
Rev. A.5, 8/03 Page- 8 method is to space the magnet down so as to cl ear the blade stop. This generally requires 1/2” of spacing (12.7mm) and Securitron offers bra ckets of the appropriate width with pre-drilled clearance holes for the Magnet mounting screws.
Rev. A.5, 8/03 Page- 9 FIG. 9: USE OF THE UMB BRACKET WITH THE MODEL 34 MAGNALOCK STOP HEADER DOOR ST RI KE MAGNET BLA DE UMB BRACKET ALUMINUM DOOR A ND FRAME WITH BLAD E STO P STOP HEADER DOOR ST RI .
Rev. A.5, 8/03 Page- 10 2.5.4 DOUBLE DOOR MOUNTING Several possibilities exist for this application. In some cases, one of the door leaves is pinned so that only one leaf is used and this is secured by a single Magnalock. If both leaves are to be active, two Magnalocks can be used.
Rev. A.5, 8/03 Page- 11 FIG. 12: WOOD FRAME AND CONCRETE HEADER BRACKET S P L I C E C H A M B E R MA G N E T SC R E W S IN TO 4 OUTSIDE TAPPED H O LES 1/2" SHEET METAL SCREWS HEADER USED FO R C O.
Rev. A.5, 8/03 Page- 12 alignment, side alignment and twisting. The Magnalo ck is also fully sealed and waterproof so it is generally unaffected by tough environments.
Rev. A.5, 8/03 Page- 13 The drawings and descriptions, show conceptual in stallation concepts for different types of gate security applications. Note that the model 62 and model 82 are most commonly used in gate installations.
Rev. A.5, 8/03 Page- 14 compatibility. Dress covers are available in clear aluminum, satin black aluminum, polished stainless and polished brass finishes. Double dress covers are also available for insta llations on double doors. In this case, the cover fits over two locks so long as they are not separated by more than 2" (50mm).
Rev. A.5, 8/03 Page- 15 wires, while observing correct pol arity. The lock, however, automatically detects whether it is receiving 12 or 24 volts and draws the correct amount of current for that voltage (the current is twice as high when the lock is re ceiving 12 volts than when it is receiving 24 volts).
Rev. A.5, 8/03 Page- 16 installations, the calculation can become quite complex so refer to Appendix B for a more complete discussion. Distance Gauge 12V Gauge 24V Distance Gauge 12V Gauge 24V 80 FT 20 GA 24 GA 800 FT 10 GA 16 GA 200 FT 17 GA 22 GA 1500 FT.
Rev. A.5, 8/03 Page- 17 3.7 DOUBLE DOOR CONTROL SWITCHING It’s common to control two locks from a single access and/or exit switch on double doors or on an installation where two locks ar e mounted on a single door.
Rev. A.5, 8/03 Page- 18 MAGNACARE ® LIMITED LIFETIME WARRANTY SECURITRON MAGNALOCK CORPORATION wa rrants that it will replace at cu stomer’s request, at any time for any reason, products manufac tured and branded by SECURITRON.
Rev. A.5, 8/03 Page- i APPENDIX A TROUBLESHOOTING PROBLEM -- No magnetic attraction betw een magnet and strike plate. First be sure the lock is being correctly powered with DC voltage. This includes connecting the power wires with correct polarity. Positive must go to red and negative to bla ck.
Rev. A.5, 8/03 Page- ii PROBLEM -- Apparent electronic noise interference w ith the access control system. Electric locks, being inductive devices, return voltage spikes on their power wires and also emit microwave radiation when switched. This can interfere with acce ss control electronics causing malfunctions.
Rev. A.5, 8/03 Page- iii Note that a Magnalock operating on 12 vo lts has 1/4th the resistance of a uni t operating on 24 VDC. This means that wire voltage drops are 4 times more significant in a 12 volt system than in a 24 volt system. In any job that has w ire runs long enough to be of concern, alw ays use 24 volts.
Rev. A.5, 8/03 Page- iv attackers will not be familiar with it. Expecting a conv entional lock which secures between the door and frame, the attacker will employ the crowbar in an attempt to spread the door edge from the frame to clear the securing latch rather than to pry the door open against t he strength of the Magnalock.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Assa Model 34 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Assa Model 34 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Assa Model 34, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Assa Model 34 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Assa Model 34, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Assa Model 34.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Assa Model 34. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Assa Model 34 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
